• Transactions on Electrical and Electronic Materials
• /
• v.1 no.4
• /
• pp.11-15
• /
• 2000

This paper presents a process optimization of antireflection (AR) coating on crystalline Si solar cells. Theoretical and experimental investigations were performed on a double-layer AR(DLAR) coating of MgFe$_2$/GeO$_2$. We investigated GeO$_2$ films as an AR layer because they have a proper refractive index of 2.46 and demonstrate the same lattice constant as Si substrate. RF sputter grown GeO$_2$ film showed deposition temperature strong dependence. The GeO$_2$ at 400$\^{C}$ exhibited a strong (111) preferred orientation and the lowest surface roughness of 6.87 $\AA$. Refractive index of MgFe$_2$film was measured as 1.386 for the most of growth temperature. An optimized DLAR coating showed a reflectance as low as 2.04% in the wavelengths ranged from 0.4 ㎛ to 1.1 ㎛. Solar cells with a structure of MgFe$_2$/GeO$_2$/Ag/N$\^$+//p-type Si/P$\^$+//Al were investigated with the without DLAR coatings. We achieved the efficiency of solar cells greater than 15% with 3.12% improvement with DLAR coatings. Further details about MgFe$_2$,GeO$_2$ films, and cell fabrication parameters are presented in this paper.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.19 no.4
• /
• pp.190-195
• /
• 2009

Na-tetrasilicic fluorine mica powders were synthesized by skull melting method. The staring materials having chemical composition of $Mg_3(OH)_2Si_4O_{10}:Na_2SiF_6:SiO_2=8.3:24.8:66.9$ mol% were charged into a cold crucible of 13 cm in diameter and 14cm in height and heated by R.F. generator at working frequency of 2.84 MHz. The materials were maintained for 1hr as a molten state and cooled down in the container. In this study, the specific electric resistance of mica was estimated and the columnar and plate shaped mica were synthesized.

• Journal of Surface Science and Engineering
• /
• v.53 no.2
• /
• pp.59-66
• /
• 2020

Effects of Na₂SiO₃ concentration added into 0.1 M NaOH + 0.05 M NaF solution on the formation behavior and properties of PEO films on AZ91 Mg alloy were investigated under 1200 Hz of alternating current (AC) by voltage-time curves, in-situ observation of arc generation behavior and measurements of film thickness, surface roughness and micro vickers hardness. In the absence of Na₂SiO₃ in the 0.1 M NaOH + 0.05 M NaF solution, about 4 ㎛ thick PEO film was formed within 1 min and then PEO film did not grow but white spots were formed by local burning. Addition of Na₂SiO₃ up to 0.2 M caused more increased formation voltage and growth of PEO film with uniform generation of arcs. Addition of Na₂SiO₃ from 0.2 M to 0.4 M showed nearly the same voltage-time behavior and uniform arc generation. Addition of Na₂SiO₃ more than 0.5 M resulted in a decrease of formation voltage and non-uniform arc generation due to local burning. PEO film growth rate increased with increasing added Na₂SiO₃ concentration but maximum PEO film thickness was limited by local burning if added Na₂SiO₃ concentration is higher than 0.5 M. Surface roughness of PEO film increased with increasing added Na₂SiO₃ concentration and appeared to be proportional to the PEO film thickness. PEO film hardness increased with increasing added Na₂SiO₃ concentration and reached a steady-state value of about 930 H_V at more than 0.5 M of added Na₂SiO₃ concentration.

• Advances in nano research
• /
• v.3 no.4
• /
• pp.243-255
• /
• 2015

In this investigation, ecotoxicity of nano and micro metal oxides, namely silica ($SiO_2$) and alumina ($Al_2O_3$), on the growth of green algae (Porphyridium aerugineum Geitler) is discussed. Effects of nano and micro particles on the growth, chlorophyll content and protein content of algae are analysed using standard protocols. Results indicate that $SiO_2$ nano and micro $SiO_2$ particles are non-toxic to P. aerugineum Geitler up to a concentration of 1000 mg/L. In addition, $Al_2O_3$ microparticles are less toxic to P. aerugineum Geitler, whereas $Al_2O_3$ nanoparticles are found to be highly toxic at 1000 mg/L. Moreover, $Al_2O_3$ nanoparticles decrease the growth, chlorophyll content, and protein content of tested algae. In addition, zeta potential and contact angle are also important in enhancing the toxicity of metal oxide nanoparticles in aquatic environment. This study highlights a new insight into toxicity evaluation of nanoparticles on beneficial aquatic organisms such as algae.

• Korean Journal of Materials Research
• /
• v.24 no.2
• /
• pp.81-86
• /
• 2014

The nitrogen solubility and nitride capacity of $CaO-SiO_2-Al_2O_3-MgO-CaF_2$ slag systems were measured by using gas-liquid equilibration at 1773K. The nitrogen solubility of this slag system decreased with increasing CO partial pressure, with the linear relationship between nitrogen contents and oxygen partial pressure being -3/4. This system was expected to show two types of nitride solution behavior. First, the nitrogen solubility decreased to a minimum value and then increased with the increase of CaO contents. These mechanisms were explained by considering that nitrogen can dissolve into slags as "free nitride" at high basicities and as "incorporated nitride" within the network at low basicities. Also, the basicity of slag and nitride capacity were explained by using optical basicity. The nitrogen contents exhibited temperature dependence, showing an increase in nitrogen contents with increasing temperature.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.2
• /
• pp.27-37
• /
• 1997

Photoluminescent and cathodoluminescent charcteristics of inorganic luminescent materials were investigated ot develop possible phosphors for thin film electroluminescent (TFEL) device applications. Mg, Zn, and Photoluminescent and cathodoluminescent charcteristics of inorganic luminescent materials were investigated ot develop possible phosphors for thin film electroluminescent (TFEL) device applications. Mg, Zn, and $Si_3N_4$ powders were used to synthesize $(Mg_xZn_{1-x})SiN_2$ host materials. $Tb_4O_7$ and $Eu_2O_3$ powdrs were added as luminescent centers. Very sharp emission spectra of $Tb^{3+}$ ions were observed from $Mg._5Zn._5SiN_2:Tb$ sampels sintered at $1400^{\circ}C$ for an hour and the maximum intensity of emission spectra occured at wavelength of 550nm (green light). Synthetic conditions of $(Mg_xZn_{1-x})SiN_2:Eu$ phosphors were optimized for the hghest luminescence. The Eu concentrations were varied from 0.2% to 1.6%. Before firing, the powders were mixed using ballmills, methanol, acetone, or D.I. water. The Mg/Zn ratio also were varied from x=0.3 to x=0.7. The maximum PL intensity was obtained from a sample with 1.2% Eu concentration and the powder was mixed with methanol and dried before firing. The maximum intensity of the emission spectra occurred t the wavelength of 470nm(blue light). TFEL devices fabricated by using sputter deposition of $(Mg._3Zn._7)SiN_2:Eu$ phosphor layer showed yellowish white emission at the phosphor field of 2MV/cm.

• Journal of Powder Materials
• /
• v.22 no.1
• /
• pp.15-20
• /
• 2015

The composite of porous silicon (Si) and amorphous carbon (C) is prepared by pyrolysis of a nano-porous Si + pitch mixture. The nano-porous Si is prepared by mechanical milling of magnesium powder with silicon monoxide (SiO) followed by removal of MgO with hydrochloric acid (etching process). The Brunauer-Emmett-Teller (BET) surface area of porous Si ($64.52m^2g^{-1}$) is much higher than that before etching Si/MgO ($4.28m^2g^{-1}$) which indicates pores are formed in Si after the etching process. Cycling stability is examined for the nano-porous Si + C composite and the result is compared with the composite of nonporous Si + C. The capacity retention of the former composite is 59.6% after 50 charge/discharge cycles while the latter shows only 28.0%. The pores of Si formed after the etching process is believed to accommodate large volumetric change of Si during charging and discharging process.

• Journal of the Korean earth science society
• /
• v.32 no.7
• /
• pp.707-718
• /
• 2011

We study the natural background and geochemical characteristics on geological groups of stream sediment in the Boseong-Hwasun area. We collected 186ea stream sediment samples along the primary channels and dried them naturally in laboratory. The contents of major, trace and rare earth elements were determined by XRF, ICP-AES and NAA analysis methods. In order to know the natural background and geochemical characteristics of geological groups, we classified the studied area into granitic gneiss (GGn) area and porphyroblastic gneiss (PGn) area. The contents range of major elements for GGn area is $SiO_2$ 45.5-73.09 wt.%, $Al_2O_3$ 12-20.76 wt.%, $Fe_2O_3$(T) 3.72-8.85 wt.%, $K_2O$ 2.38-4.2 wt.%, MgO 0.75-2.77 wt.%, $Na_2O$ 0.78-1.88 wt.%, CaO 0.27-2.1 wt.%, $TiO_2$ 0.56-1.72 wt.%, $P_2O_5$ 0.06-0.73 wt.% and MnO 0.03-0.95 wt.%, and for PGn area it is $SiO_2$ 43.74-70.71 wt.%, $Al_2O_3$ 11.54-25.05 wt.%, $Fe_2O_3$(T) 3.44-13.46 wt.%, $K_2O$ 2.08-3.86 wt.%, MgO 0.65-2.99 wt.%, $Na_2O$ 0.63-1.7 wt.%, CaO 0.35-2.07 wt.%, $TiO_2$ 0.68-4.17 wt.%, $P_2O_5$ 0.1-0.31 wt.% and MnO 0.07-0.33 wt.%. The contents range of hazard elements for GGn area is Cr 41.7-242 ppm, Co 7.6-25.1 ppm, Ni 12-61 ppm, Cu 10-47 ppm, Zn 48.5-412 ppm, Pb 17-215 ppm, and for PGn area, it is Cr 29.6-454 ppm, Co 5.9-53.7 ppm, Ni 8.7-287 ppm, Cu 6.4-134 ppm, Zn 43.6-370 ppm, Pb 15-37 ppm area. There is a good correlation between Cr and MgO and Co among $Al_2O_3$, $Fe_2O_3$(T), MgO and Ni among $Fe_2O_3$(T), CaO, MgO whereas Cu, Zn and Pb have a low correlation for major elements in GGn area. Generally Cr, Co, Ni, and Cu have a good correlation with major elements, but a low correlation with Zn and Pb in PGn area.

• Journal of the Korean Ceramic Society
• /
• v.20 no.4
• /
• pp.305-314
• /
• 1983

In order to enhance the rate of th nitridation and to give the high density of reaction-bonded silicon nitride MgO powder as nitriding aid were added to silicon powders and the mixture was pressed isostatically into compacts which were nitrided in the furnace of 1, 35$0^{\circ}C$ where 95% $N_2$-5% $H_2$ gases were flowing. As the other nitriding aid $Mg(NO_3)_2 6H_2O$ was selected, A slip made of magnesium nitrate solution and fine silicon particles was spray-dried and then decomposed at 30$0^{\circ}C$. Magnesium oxide-coated silicon powders were formed into compacts prior to the nitridation on the same condition as the former. Magnesium nitrate (MgO, produced from the decomposition of magnesium nitrate) was more effective for the formation of the $\beta$-phase in the initial stage of the nitridation probably due to the easy formation of $MgO-SiO_2$-metal oxide eutectic melt. It has been confirmed that forsterite was formed as a result of the reaction between MgO and $SiO_2$ film of silicon surface. It was considered that MgO produced from magnesium nitrate may be finer more reactive and more uniformly distributed on the surface of silicon particles than original MgO. The higher the forming pressure was the more the $\beta$-phase was formed.

• Current Research on Agriculture and Life Sciences
• /
• v.4
• /
• pp.1-6
• /
• 1986

This study was conducted to find out the effect of $SiO_2$ treatment on the $SiO_2$ concentration in guttation liquid, the amount of guttation liquid exudated from the margin of rice leaves, and the relationships between $SiO_2$ concentration in guttation liquid and foliar burn during the rice seedling stage, using two rice varieties;Nagdong-byeo (a Japonica) and Samgang-byeo (a - Indica - Japonica hybrid). Seedlings were cultivated in water solution and enveloped in polyvinyl case ($50cm{\times}150cm{\times}70cm$). $SiO_2$ treatment increased the amount of guttation liquid, the amount of guttation liquid (Nagdong-byeo:4.30mg/plant, Samgang-byeo:4.34mg/plant)) treated with 200ppm of $SiO_2$ was greater than any other level, decreased over 200ppm of $SiO_2$. $SiO_2$ concentration in guttation liquid was increased as application rates of $SiO_2$ increased, showing the positive correlation, and $SiO_2$ in guttation liquid/$SiO_2$ in culture ratio decreased over 100ppm of $SiO_2$. The highest concenitration of $SiO_2$ (Nagdong-byeo:172.6ppm/lcc, Samgang-byeo:199.8ppm/lcc) in guttation liquid was obtained at 12 hrs after $SiO_2$ applied. Foliar burn seemed to be closely related with $SiO_2$ concentration in guttation liquid.