• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.373-373
• /
• 2011

$Cu(In,Ga)Se_2$(CIGS) 박막 태양전지는 Chalcopyrite계 박막 태양전지로 Cu, In, Ga, Se 각 원소의 조성을 적절히 조절하여 박막을 성장시킨다. 성장시킨 CIGS 박막은 광흡수계수가 105cm-1로 다른 물질 보다 뛰어나고 직접 천이형 반도체로서 얇은 두께로도 고효율의 박막 제작이 가능하다. 얇은 두께로도 충분히 빛의 흡수가 가능하지만, cell 표면 반사에 의한 광 손실은 cell 효율을 떨어뜨리게 된다. 본 연구에서는 CIGS 박막 태양전지의 광 흡수 향상을 위해 굴절률이 1.86인 ITO 위에 ITO보다 굴절률이 작은 $MgF_2$ (n=1.377) [1]를 80, 100, 120, 140 nm로 증착하여 $MgF_2$/Al/Ni/ITO/i-ZnO/CdS/CIGS/Mo/SLG 시료를 제작하고, optical reflectance, Quantum Efficiency를 이용하여 분석하였다. optical reflectance 분석 결과, $MgF_2$ AR coating을 한 경우, 두께가 두꺼워짐에 따라 광 반사도가 감소하는 경향을 보였다. 또한 AR coating 두께가 커짐에 따라 fluctuation이 점점 커지며, 파형이 장파장 쪽으로 shift하는 것을 관찰 할 수 있었다. Quantum efficiency (QE)를 분석한 결과 $MgF_2$ AR coating 할 경우, 측정된 대부분의 파장에서 QE가 향상되는 것을 확인할 수 있었다. 하지만 AR coating 두께에 따른 변화는 뚜렷한 차이를 보이지 않았다. AR coating 결과, JSC가 증가하여 efficiency가 향상되는 것을 확인 할 수 있다. 그러나 $MgF_2$ AR coating 80~140 nm 범위에서 cell 효율 변화의 뚜렷한 차이는 관찰할 수 없었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 춘계학술대회 논문집
• /
• pp.593-596
• /
• 1999

This paper presents a process optimization of antireflectiun (AR) coating on crystalline Si solar cells. Theoretical and experimental investigations were performed on a doble-layer AR(DLAR) coating of MgF$_2$/CeO$_2$, We investigated CeO$_2$ films as an All layer because they hale a proper refractive index of 2.46 and demonstrate the same lattice constant as Si substrate. RF sputter grown CeO$_2$ film showed strong dependence on a deposition temperature. The CeO$_2$ film deposited at 400 $^{\circ}C$ exhibited a strong (111) preferred orientation and the lowest surface roughness of 6.87 $\AA$. Refractive index of MgF$_2$ film was measured as 1.386 for the most of growth temperature. An optimized DLAR coating showed a reflectance as low as 2.04 % in the wavelengths ranged from 0.4 7m to 1.1 7m. We achieved the efficiencies of solar cells greater than 15% with 3.12 % improvement with DLAR coatings . Further details on MgF$_2$, CeO$_2$ films, and cell fabrication Parameters are presented in this paper.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제52권10호
• /
• pp.447-450
• /
• 2003

This paper presents a process optimization of antireflection (AR) coating on crystalline Si solar cells. Theoretical and experimental investigations were performed on a double-layer AR (DLAR) coating of MgF$_2$/CeO$_2$. We investigated CeO$_2$ films as an AR layer because they have a proper refractive index of 2.46 and demonstrate the same lattice constant as Si substrate. RF sputter grown CeO$_2$ film showed strong dependence on a deposition temperature. The CeO$_2$ deposited at 40$0^{\circ}C$ exhibited a strong (111) preferred orientation and the lowest surface roughness of 6.87 $\AA$. Refractive index of MgF$_2$ film was measured as 1.386 for the most of growth temperature. An optimized DLAR coating showed a reflectance as low as 2.04% in the wavelengths ranged from 0.4${\mu}{\textrm}{m}$ to 1.1${\mu}{\textrm}{m}$. We achieved the efficiencies of solar cells greater than 15% with 3.12% improvement with DLAR coatings. Further details on MgF$_2$, CeO$_2$ films, and cell fabrication parameters are presented in this paper.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.251-254
• /
• 2001

This paper describes an efficiency improvement of buried contact solar cell (BSCS) with a structure of MgF$_2$/CeO$_2$/Ag/Cu/Ni grid/n$^{+}$ emitter/p-type Si base/p$^{+}$/Al. Theoretical and experimental investigations were performed on a double layer antireflection (DLAR) coating of MgF$_2$/CeO$_2$. We investigated CeO$_2$ films as an AR layer because they have a proper refractive index of 2.46 and demonstrate the same lattice constant as Si substrate. An optimized DLAR coating shewed a reflectance as low as 2.04 % in the wavelengths ranged from 0.4 ${\mu}{\textrm}{m}$ to 1.1 ${\mu}{\textrm}{m}$. BCSC cell efficiency was improved from 16.2 % without any AR coating to 19.9 % by employing DLAR coatings. Further details on MgF$_2$/CeO$_2$ DLAR coatings on the BCSC cells are presented in this paper.per.

• 전자공학회논문지
• /
• 제52권5호
• /
• pp.206-213
• /
• 2015

함정용 전자광학추적장비의 센서부에서 해수면반사파에 의해 발생하게 되는 영상추적간섭 현상을 최소화하고자 전방향성, 점진적인 굴절률 및 표면 요철구조를 갖는 산화아연에 플루오르화마그네슘을 코팅한 반사방지막을 전자빔 증착 장비를 통해 제작하였다. 최적화된 산화아연에 플루오르화마그네슘을 코팅한 반사방지막은 기존의 산화아연 반사방지막과 비교하여 점진적인 굴절률 변화에 따라 표면 프레넬 반사를 최소화하고 이를 통해 전자광학추적장비의 영상추적간섭 현상을 제거하는 장점이 있다. 본 실험을 통해, 산화아연에 플루오르화마그네슘을 코팅한 반사방지막이 다양한 전자광학장비의 반사방지막으로써 적용이 가능함을 확인하였다.

• 열처리공학회지
• /
• 제36권4호
• /
• pp.198-205
• /
• 2023

We investigated the effects of Al and Mg on the microstructure and hardness of the coating layer of galvanized steel sheets, by thermodynamic calculations, X-ray diffraction, scanning electron microscopy, and Vickers hardness tests of Zn-0.2Al, Zn-6Al-2Mg, and Zn-10Al-5Mg coating layers. Regardless of the alloy composition of the galvanizing bath, a Fe-Al layer was observed between the coating layer and steel sheet. The Zn-0.2Al coating layer consists of major h.c.p. Zn phase and minor f.c.c. Al phase. The fraction of f.c.c. Al phase (containing a significant amount of Zn) of the coating layer increases with increasing the chemical composition of Al of the galvanizing bath. The h.c.p. MgZn₂ phase was formed in the Al/Mg-containing Zn-6Al-2Mg and Zn-10Al-5Mg coating layers, forming Zn-Al-MgZn₂ eutectic microstructure. The primary MgZn₂ phase was additionally formed in the Zn-10Al-5Mg coating layers containing high concentrations of Al and Mg. The Vickers hardness values of Zn-0.2Al, Zn-6Al-2Mg, and Zn-10Al-5Mg coating layers were 59.1 ± 1.2 HV, 161.2 ± 5.7 HV, and 215.5 ± 40.3 HV, respectively. The addition of Al and Mg increased the hardness of the coating layer by increasing the fraction of the Al phase (containing Zn) and MgZn₂ intermetallic compound, which were harder than the Zn phase.

• 한국표면공학회지
• /
• 제43권2호
• /
• pp.97-104
• /
• 2010

In this paper, we conducted MATLAB simulation using the reflectance formula and the Planck's black body radiation principle, for the purpose of identifying the opimum material and thickness of anti-reflective coating from double layered structures. We found that the optimum condition was obtained when refractive index of upper layer is 1.44 and that of lower layer is 2.29. As materials close to these refractive indices, $MgF_2$ as the upper layer and $HfO_2$, ZnS, $TiO_2$ as the lower layer were suggested. The best result in an average reflectance of 2.759% was obtained from a double layered structure of $MgF_2$ 94 nm/ZnS 55 nm.

• Journal of Information Display
• /
• 제7권2호
• /
• pp.1-5
• /
• 2006

The characteristics of MgO layer deposited under hydrogen atmosphere were investigated. Hydrogen gas was introduced during e-beam evaporation coating process of MgO layer and its effects on microstructure, cathode luminescence spectra, discharge voltages and effective yield of secondary electron emission were examined. The results indicated that the hydrogen influences the concentration and energy levels of defects in MgO layer, which in turn affects the luminance efficiency and discharge delays of the panels significantly.

• 한국안광학회지
• /
• 제7권2호
• /
• pp.175-180
• /
• 2002

렌즈의 thin film 균일성을 평가하기 위하여 spctrophotometer를 이용한다. 렌즈의 중심 중간, edge 등의 지점에서 파장의존상의 반사율을 측정하여 반사율 spectrum의 두 peak를 선택하여 비교하여, 박막 균일성 여부를 분석한다. 반사율의 두 peak의 파장 영역(${\lambda}_1,{\lambda}_2$)으로부터 thin film의 thickness(t)를 구한다. $$t=\frac{1}{2(n^2-\sin^2{\theta})^{1/2}}{\times}\frac{{\lambda}_1{\lambda}_2}{{\lambda}_2-{\lambda}_1}$$ 렌즈의 중심 중간, edge 등의 지점에서 반사율 pattern이 동일 값이면 coating 렌즈의 박막은 균일성 갖는다. coating 렌즈의 박막 균일성 평가 방법을 단층막 $MgF_2$(n=1.38) coating 렌즈에 적용하였다. 박막의 thickness 차이는 360nm 정도였다. 파장의존성에 대한 광반사율의 측정으로부터 coating 렌즈의 박막 균일성을 쉽게 분석할 수 있다.

• 한국재료학회지
• /
• 제32권6호
• /
• pp.301-306
• /
• 2022

This study explored the possibility of forming a coating layer containing alginic acid on the surface of a magnesium alloy to be used as a biomaterial. We formed a coating layer on the surface of a magnesium alloy using a plasma electrolytic oxidation process in an electrolytic solution with different amounts of alginic acid (0 g/L ~ 8 g/L). The surface morphology of all samples was observed, and craters and nodules typical of the PEO process were formed. The cross-sectional shape of the samples confirmed that the thickness of the coating layer became thicker as the alginic acid concentration increased. It was confirmed that the thickness and hardness of the sample significantly increase with increasing alginic acid concentration. The porosity of the surface and cross section tended to decrease as the alginic acid concentration increased. The XRD patterns of all samples revealed the formation of MgO, Mg₂SiO₄, and MgF₂ complex phases. Polarization tests were conducted in a Stimulate Body Fluid solution similar to the body's plasma. We found that a high amount of alginic acid concentration in the electrolyte improved the degree of corrosion resistance of the coating layer.