• 대한의용생체공학회:의공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• 마케팅과학연구
• /
• 제19권3호
• /
• pp.17-27
• /
• 2009

典型的价格促销是指降低一定数量产品的价格或以相同的价 格获得更多数量的产品, 从而增加价值和创造经济的激励购买. 价格促销经常用来鼓励没有消费过产品或服务的用户试用产品或服务. 因此, 理解价格促销对那些从来没有使用过促销品牌的消费者的此品牌质量认知的影响是很重要的. 然而, 如果消费者通过价格促销获得的产品的质量不好, 促销可能达不到用经济的刺激方法来增加销售的效果. 相反则有可能发生. 具体来说, 通过价格促销消费者产生低的质量的认知会削弱经济的和心理上的激励, 减少购买的可能性. 因此, 对市场营销人员来说理解品牌的价格促销信息如何影响消费者对此品牌的质量的不良认知是非常重要的. 先前的有关价格促销对质量认知的影响的研究有不一致的解释. 一些是关注价格促销对消费者认知的不利影响. 但是其他的研究显示价格促销并没有提高消费者对品牌的不良认知. 之前的研究发现这些不一致的结果和价格促销曝光的时机以及相关的试验得出的质量评估有关. 而且, 消费者是否经历过产品促销都可能会调节这些影响. 一些研究把产品类别的不同作为基本的因素. 本研究的目的是探讨在不同的情况下, 价格促销信息对消费者的不良的质量认知产生的影响. 作者控制了促销曝光的时机, 过去的各种促销形式以及信息发布的方式. 与以往的研究不同, 作者通过控制以前个人使用此产品的经验的潜在调节作用来测试事先设定限制的价格促销的影响. 这样的操作可以解决相关的有可能产生的争议. 这种方法对实际工作方面也是有意义的. 价格促销不仅适用于已存在的目标消费者, 而且可以鼓励没有使用过产品和服务的消费者尝试此产品或服务. 因此, 对市场营销人员来说理解品牌的价格促销信息如何影响消费者对此品牌的质量的不良认知是非常重要的. 如果没有使用过这个品牌的消费者通过价格促销获得的产品的质量不好, 促销可能达不到用经济的刺激方法来增加销售的效果. 相反则有可能发生. 另外, 如果价格促销结束, 购买了这个产品的消费者可能会出现明显的减少再购买行为. 通过文献回顾, 假设1用来探讨消费者通过过去的价格促销获得的质量认知的调节作用. 消费者对没有使用过的品牌的价格促销而产生的质量认知的影响会被此品牌过去的价格促销活动所调节. 换句话说, 消费者会对没有进行过价格促销的没有使用过的品牌产生不良的质量认知. 假设2-1:未使用过的品牌进行首次价格促销的时候, 价格促销的信息发布的方式将影响价格促销的成败. 假设2-2:消费者越不在意价格促销的原因, 越容易对产品的质量产生不良的认知. 通过测试1, 简要地解释了产品和品牌在提供四种价格促销形式之前并解释说明了每种价格促销形式. WAVEX这个虚拟品牌的质量的认知被评估为7. 网球拍被选中的原因是由于选定的产品组必须过去几乎没有价格促销活动来消除促销的平均次数对价格促销信息的影响, 正如Raghubir和Corfman(1999)所提出的. 测试2也用网球拍作为产品组, 主持测试2的管理者与测试1相同. 随着测试1, 选择了对产品组熟悉而对产品不熟悉的受访者. 每个受访者被分配到代表WAVEX价格促销的两种不同信息发布方式的两组中的一组. 在评估WAVEX的质量认知为7以前, 受访者看了每个促销信息. 不熟悉的实验品牌的价格促销对消费者的质量认知的影响被证明为会被以前有过或没有价格促销活动所调节. 与过去的促销行为一致是使品牌评估变得更糟的不良影响的重要变量. 如果此品牌从未进行过价格促销, 价格促销活动会对消费者的质量认知产生不良的影响. 第二, 不熟悉的品牌进行首次价格促销时, 促销信息的发布方式会影响公司促销的成败. 当消费者进行性格归因和情境归因的比较时, 质量认知的不良影响会更大. 与先前主要关注具有或不具有情境/性格归因中良好或不良的动机的研究不同, 本研究的焦点是检验如果公司提出了具有说服性的理由, 即使消费者在价格促销行为中有性格归因, 情境归因也可以被推断出的事实. 这种方法, 在学术方面取得了很大的成果, 意义在于它运用非数学的问题来解释固定和调整过程而不像以前的研究大部分是把它用于数学问题来解释. 换句话说, 根据基本属性错误, 有很大的倾向去性格地归因其他的行为. 当这种情况出现在价格促销时, 我们可以推断出消费者很有可能性格地归因公司的价格促销行为. 反而, 即使在这种情况下, 公司可以调整消费者的锚定性来降低性格归因的可能性. 另外, 不像多数对价格促销的长/短期影响的以往的研究, 只考虑价格促销对消费者的购买行为影响, 本 研究测试对质量认知的影响, 一个影响消费者购买行为的因素. 这些结果在实际工作方面有重要启示. 本研究的结果可以作为新产品有效的提供促销信息的指南. 如果品牌要避免错误的暗示, 比如在施行价格促销战略时被认为是产品的质量不好, 一定要为促销提供清晰合理的理由. 尤其是对那些以前没有进行过价格促销活动的公司来说, 提供明确的理由尤其重要. 不一致的行为可以导致消费者的不信任和焦虑. 这也是无止境的价格战的风险的重要因素之一. 没有事先通知的价格促销会使消费者怀疑, 但不会影响市场份额.

• 한국농공학회지
• /
• 제16권1호
• /
• pp.3225-3262
• /
• 1974

The purposes of this thesis are to clarify experimentally the variation of ground water temperature in tube wells during the irrigation period of paddy rice, and the effect of ground water irrigation on the growth, grain yield and yield components of the rice plant, and, furthermore, when and why the plant is most liable to be damaged by ground water, and also to find out the effective ground water irrigation methods. The results obtained in this experiment are as follows; 1. The temperature of ground water in tube wells varies according to the location, year, and the depth of the well. The average temperatures of ground water in a tubewells, 6.3m, 8.0m deep are $14.5^{\circ}C$ and $13.1^{\circ}C$, respercively, during the irrigation period of paddy rice (From the middle of June to the end of September). In the former the temperature rises continuously from $12.3^{\circ}C$ to 16.4$^{\circ}C$ and in the latter from $12.4^{\circ}C$ to $13.8^{\circ}C$ during the same period. These temperatures are approximately the same value as the estimated temperatures. The temperature difference between the ground water and the surface water is approximately $11^{\circ}C$. 2. The results obtained from the analysis of the water quality of the "Seoho" reservoir and that of water from the tube well show that the pH values of the ground water and the surface water are 6.35 and 6.00, respectively, and inorganic components such as N, PO4, Na, Cl, SiO2 and Ca are contained more in the ground water than in the surface water while K, SO4, Fe and Mg are contained less in the ground water. 3. The response of growth, yield and yield components of paddy rice to ground water irrigation are as follows; (l) Using ground water irrigation during the watered rice nursery period(seeding date: 30 April, 1970), the chracteristics of a young rice plant, such as plant height, number of leaves, and number of tillers are inferior to those of young rice plants irrigated with surface water during the same period. (2) In cases where ground water and surface water are supplied separately by the gravity flow method, it is found that ground water irrigation to the rice plant delays the stage at which there is a maximum increase in the number of tillers by 6 days. (3) At the tillering stage of rice plant just after transplanting, the effect of ground water irrigation on the increase in the number of tillers is better, compared with the method of supplying surface water throughout the whole irrigation period. Conversely, the number of tillers is decreased by ground water irrigation at the reproductive stage. Plant height is extremely restrained by ground water irrigation. (4) Heading date is clearly delayed by the ground water irrigation when it is practised during the growth stages or at the reproductive stage only. (5) The heading date of rice plants is slightly delayed by irrigation with the gravity flow method as compared with the standing water method. (6) The response of yield and of yield components of rice to ground water irrigation are as follows: \circled1 When ground water irrigation is practised during the growth stages and the reproductive stage, the culm length of the rice plant is reduced by 11 percent and 8 percent, respectively, when compared with the surface water irrigation used throughout all the growth stages. \circled2 Panicle length is found to be the longest on the test plot in which ground water irrigation is practised at the tillering stage. A similar tendency as that seen in the culm length is observed on other test plots. \circled3 The number of panicles is found to be the least on the plot in which ground water irrigation is practised by the gravity flow method throughout all the growth stages of the rice plant. No significant difference is found between the other plots. \circled4 The number of spikelets per panicle at the various stages of rice growth at which_ surface or ground water is supplied by gravity flow method are as follows; surface water at all growth stages‥‥‥‥‥ 98.5. Ground water at all growth stages‥‥‥‥‥‥62.2 Ground water at the tillering stage‥‥‥‥‥ 82.6. Ground water at the reproductive stage ‥‥‥‥‥ 74.1. \circled5 Ripening percentage is about 70 percent on the test plot in which ground water irrigation is practised during all the growth stages and at the tillering stage only. However, when ground water irrigation is practised, at the reproductive stage, the ripening percentage is reduced to 50 percent. This means that 20 percent reduction in the ripening percentage by using ground water irrigation at the reproductive stage. \circled6 The weight of 1,000 kernels is found to show a similar tendency as in the case of ripening percentage i. e. the ground water irrigation during all the growth stages and at the reproductive stage results in a decreased weight of the 1,000 kernels. \circled7 The yield of brown rice from the various treatments are as follows; Gravity flow; Surface water at all growth stages‥‥‥‥‥‥514kg/10a. Ground water at all growth stages‥‥‥‥‥‥428kg/10a. Ground water at the reproductive stage‥‥‥‥‥‥430kg/10a. Standing water; Surface water at all growh stages‥‥‥‥‥‥556kg/10a. Ground water at all growth stages‥‥‥‥‥‥441kg/10a. Ground water at the reproductive stage‥‥‥‥‥‥450kg/10a. The above figures show that ground water irrigation by the gravity flow and by the standing water method during all the growth stages resulted in an 18 percent and a 21 percent decrease in the yield of brown rice, respectively, when compared with surface water irrigation. Also ground water irrigation by gravity flow and by standing water resulted in respective decreases in yield of 16 percent and 19 percent, compared with the surface irrigation method. 4. Results obtained from the experiments on the improvement of ground water irrigation efficiency to paddy rice are as follows; (1) When the standing water irrigation with surface water is practised, the daily average water temperature in a paddy field is 25.2$^{\circ}C$, but, when the gravity flow method is practised with the same irrigation water, the daily average water temperature is 24.5$^{\circ}C$. This means that the former is 0.7$^{\circ}C$ higher than the latter. On the other hand, when ground water is used, the daily water temperatures in a paddy field are respectively 21.$0^{\circ}C$ and 19.3$^{\circ}C$ by practising standing water and the gravity flow method. It can be seen that the former is approximately 1.$0^{\circ}C$ higher than the latter. (2) When the non-water-logged cultivation is practised, the yield of brown rice is 516.3kg/10a, while the yield of brown rice from ground water irrigation plot throughout the whole irrigation period and surface water irrigation plot are 446.3kg/10a and 556.4kg/10a, respectivelely. This means that there is no significant difference in yields between surface water irrigation practice and non-water-logged cultivation, and also means that non-water-logged cultivation results in a 12.6 percent increase in yield compared with the yield from the ground water irrigation plot. (3) The black and white coloring on the inside surface of the water warming ponds has no substantial effect on the temperature of the water. The average daily water temperatures of the various water warming ponds, having different depths, are expressed as Y=aX+b, while the daily average water temperatures at various depths in a water warming pond are expressed as Y=a(b)x (where Y: the daily average water temperature, a,b: constants depending on the type of water warming pond, X; water depth). As the depth of water warning pond is increased, the diurnal difference of the highest and the lowest water temperature is decreased, and also, the time at which the highest water temperature occurs, is delayed. (4) The degree of warming by using a polyethylene tube, 100m in length and 10cm in diameter, is 4~9$^{\circ}C$. Heat exchange rate of a polyethylene tube is 1.5 times higher than that or a water warming channel. The following equation expresses the water warming mechanism of a polyethylene tube where distance from the tube inlet, time in day and several climatic factors are given: {{{{ theta omega (dwt)= { a}_{0 } (1-e- { x} over { PHI v })+ { 2} atop { SUM from { { n}=1} { { a}_{n } } over { SQRT { 1+ {( n omega PHI) }^{2 } } } } LEFT { sin(n omega t+ { b}_{n }+ { tan}^{-1 }n omega PHI )-e- { x} over { PHI v }sin(n omega LEFT ( t- { x} over {v } RIGHT ) + { b}_{n }+ { tan}^{-1 }n omega PHI ) RIGHT } +e- { x} over { PHI v } theta i}}}}{{{{ { theta }_{$\infty$ }(t)= { { alpha theta }_{a }+ { theta }_{ w'} +(S- { B}_{s } ) { U}_{w } } over { beta } , PHI = { { cpDU}_{ omega } } over {4 beta } }}}} where $\theta$$\omega$; discharged water temperature($^{\circ}C$) $\theta$a; air temperature ($^{\circ}C$) $\theta$$\omega$';ponded water temperature($^{\circ}C$) s ; net solar radiation(ly/min) t ; time(tadian) x; tube length(cm) D; diameter(cm) ao,an,bn;constants determined from $\theta$$\omega$(t) varitation. cp; heat capacity of water(cal/$^{\circ}C$ ㎥) U,Ua; overall heat transfer coefficient(cal/$^{\circ}C$ $\textrm{cm}^2$ min-1) $\omega$;1 velocity of water in a polyethylene tube(cm/min) Bs ; heat exchange rate between water and soil(ly/min)

• 한국문헌정보학회지
• /
• 제24권
• /
• pp.289-332
• /
• 1993

In china, six bibliographies of offical historical books are evaluated at the most important things among the systematically-editing bibliographies. These bibliographies would be usful to study the orign of classical sciences and their development, bibliographic research of Chinese classics, bibliographic judgement on genuine books, titles, authors, volumes. They could be refered to research into graving, correcting, and existence of ancient books. therefore, these bibliographies would be applied to estimation the phase of scientific and cultural development. The study of these bibliographies has been not yet made in Korea. This thesis lays its importance on the background of their appearance, their classification norms, organizing system of their catalogue, and comparison between their difference. 1. Editing and compiling of Chilyak (칠약) by Liu Chin (유흠) and official histories played an important role of entering an apperance of historical book's bibliographies. Chilyak has been lost. However, its classification and compiling system of classical books would be traced by Hansoyemunji(한서예문지) of which basic system is similar to Chilyak. It classified books according to their scientific characteristic. If a few books didn't have their own categories, they were combined by the circles parallel to the books' characteristic. With the books classified under the same scientific characteristic, they were again divided into the scientific schools or structures. It also arranged the same kinds of books according to the chronology. The some books wi th duplicate subjects were classified multiplely by their duplicate subject. 2. Ssu-ma Chon's (사마천) The Historical Records (Saki, 사기) and Pan Ku's (반고) The History of the Former Han Dynasty (Hanso, 한서) has also took effects on appearance of historical books' bibliographies. Covering overall history, Saki was structured by the five parts: The basic annals(본기), the chronological tables (표), the documents (서), the hereditary houses (세가), biographies (열전). The basic annals dealt with kings and courts' affairs according to the chronology. The chronological tables was the records of the annals. The documents described overall the social and cultural systems. The hereditary houses recorded courts' meritorious officials and public figures. The biographies showed exemplars of seventy peoples selected by their social status. Pan Ku(반구)'s The History of the Former Han Dynasty(한서) deserved to be called the prototype for the offical histories after Saki's (사기; The Historical Records) apperance. Although it modelled on Saki, it had set up its own cataloguing system. It was organized by four parts; the basic annals (본기), the chronological tables (표), treatises(지), biographies (열전). The documents in the Hanso(한서) was converted into treatises(지). The hereditary houses and biographies were merged. For the first time, the treatise with The Yemunji could operate function for historical bibliographies. 3. There were six historical bibliographies: Hansoyemunji(한서예문지), Susokyongjeokji (수서경적지), Kudangsokyongjeokji(구당서경적지), Shindangsoyemunji (신당서예문지), Songsayemunji (송사예문지), Myongsayemunji (명사예문지). 1) Modelling on Liu Chin's Chilyak except Chipryak(집략), Hansoyemunji divided the characteristic of the books and documents into six parts: Yukrye(육예), Cheja(제자), Shibu(시부), Pyongsoh(병서), Susul(수술), Pangki(방기). Under six parts, there were thirty eight orders in Hansoyemunji. To its own classification, Hansoyemunji applied the Chilyak's theory of classification that the books or documents were managed according to characteristic of sciences, the difference of schools, the organization of sentences. However the overlapped subjects were deleted and unified into one. The books included into an unsuitable subject were corrected and converted into another. The Hansoyemunji consisted of main preface (Taesoh 대서), minor preface (Sosoh 소서) , the general preface (Chongso 총서). It also recorded the introduction of books and documents, the origin of sciences, the outline of subjects, and the establishment of orders. The books classified by the subject had title, author, and volumes. They were rearranged by titles and the chronological publication year. Sometimes author was the first access point to catalogue the books. If it was necessary for the books to take footnotes, detail notes were formed. The Volume number written consecutively to order and subject could clarify the quantity of books. 2) Refering to Classfication System by Seven Norms (칠분법) and Classification System by Four Norms(사분법), Susokyongjeokji(수서경적지) had accomplished the classification by four norms. In fact, its classification largely imitated Wanhyosoh(완효서)'s Chilrok(칠록), Susokyongjeokji's system of classification consisted of four parts-Kyung(경), Sa(사), Cha(자), Chip(칩). The four parts were divided into 40 orders. Its appendix was again divided into two parts, Buddihism and Taiosm. Under the two parts there were fifteen orders. Totally Susokyongjeokji was made of six parts and fifty five orders. In comparison with Hansoyemunji(한서예문지), it clearly showed the conception of Kyung, Sa, Cha, Chip. Especially it deserved to be paid attention that Hansoyemunji laied history off Chunchu(춘추) and removed history to Sabu(사부). However Chabu(사부) put many contrary subjects such as Cheja(제자), Kiye(기예), Sulsu(술수), Sosol(소설) into the same boundary, which committed errors insufficient theoretical basis. Anothor demerit of Susokyongjeokji was that it dealt with Taiosm scriptures and Buddism scriptures at the appendix because they were considered as quasi-religion. Its compilation of bibliographical facts consisted of main preface(Taesoh 대서), minor preface(Sosoh 소서), general preface (Chongsoh 총서), postscript (Husoh 후서). Its bibliological facts mainly focused on the titles. Its recorded authors' birth date and their position. It wrote the lost and existence of books consecutive to total number of books, which revealed total of the lost books in Su Dynasty. 3) Modelling on the basis of Kokumsorok(고분서록) and Naewaekyongrok(내외경록), Kudangsokyongjeokji(구당서경적지) had four parts and fourty five orders. It was estimated as the important role of establishing basic frame of classification by four norms in classification theory's history. However it had also its own limit. Editing and compling orders of Kudangsokyongjeokji had been not progressively changed. Its orders imitated by and large Susokyongjeokji. In Its system of organizing catalogue, with its minor preface and general preface deleting, Kudangsokyongjeokji by titles after orders sometimes broke out confusion because of unclear boundaries between orders. 4) Shindangsoyemunji(신당서예문지), adding 28,469 books to Kudangsokyongjeokji, recorded 82,384 books which were divided by four parts and fourty four orders. In comparison with Kudangkyongjeokj, Sindangsoyemunji corrected unclear order's norm. It merged the analogical norms four orders (for instance, Kohun 고훈 and Sohakryu 소학류) and seperated the different norms four orders (for example, Hyokyong 효경 and Noneuhryu 논어류, Chamwi 참위 and Kyonghaeryu 경해류, Pyonryon 편년 and Wisaryu 위사류). Recording kings' behaviors and speeches (Kikochuryu 기거주류) in the historical parts induced the concept of specfication category. For the first time, part of Chipbu (집부) set up the order of classification norm for historical and literatural books and documents (Munsaryu 문사류). Its editing and compiling had been more simplified than Kudangsokyongjeokji. Introduction was written at first part of bibliographies. Appendants except bibliographic items such subject, author, title, volume number, total were omitted. 5) Songsayemunji(송사예문지) were edited in the basis of combining Puksong(북송) and Namsong(남송), depending on Sabukuksayemunji(사부국사예문지). Generally Songsayemunji had lost a lot of bibliographical facts of many books. They were duplicated and wrongly classified books because it committed an error of the incorrectly annalistic editing. Particularly Namsong showed more open these defaults. Songsayemunji didin't include the books published since the king Youngchong(영종). Its system of classification was more better controlled. Chamwiryu(참위류) in the part of Kyongbu(경부) was omitted. In the part of history(Sabu 사부), recordings of kings' behaviors and speeches more merged in the annals. Historical abstract documents (Sachoryu 사초류) were seperately arranged. In the part of Chabu(자부), Myongdangkyongmaekryu(명당경맥류) and Euisulryu(의술류) were combined. Ohangryu(오행류) were laied off Shikuryu(시구류). In the part of Chipbu(집부), historical and literatural books (Munsaryu 문사류) were independentely arranged. There were the renamed orders; from Wisa(위사) to Paesa(패사), Chapsa (잡사) to Pyolsa(열사), Chapchonki(잡전기) to Chonki(전기), Ryusoh(류서) to Ryusa(류서). Introduction had only main preface. The books of each subject catalogued by title, the volume number, and author and arranged mainly by authors. Annotations were written consecutively after title and the volume number. In the afternote the number of not-treated books were revealed. Difference from Singdangsohyemunji(신당서예문지) were that the concept and boundary of orders became more clearer. It also wrote the number of books consecutive to main subject. 6) Modelling on Chonkyongdangsomok (경당서목), Myongsayemunji(명사예문지) was compiled in the basis of books and documents published in the Ming Danasty. In classification system, Myongsayemunji partly merged and the seperated some orders for it. It also deleted and renamed some of orders. In case of necessity, combining of orders' norm was occured particulary in the part of Sabu(사부) and Chabu(자부). Therefore these merging of orders norm didn't offer sufficient theretical background. For example, such demerits were seen in the case that historical books edited by annals were combined with offical historical ones which were differently compiled and edited from the former. In the part of Chabu(자부), it broke out another confusion that Pubga(법가), Meongga(명가), Mukga(묵가), Chonghweongka's(종횡가) thoughts were classified in the Chapka(잡가). Scriptures of Taiosim and Buddhism were seperated from each other. There were some deleted books such as Mokrokryu(목록류), Paesaryu(패사류) in the part of history (Sabu 사부) and Chosaryu(초사류) in the part of Chipbu(집부). The some in the each orders had been renamed. Imitating compiling system of Songsayemunji(송사예문지), with reffering to its differ-ence, Myongsayemunji(명사예문지) wrote the review and the change of the books by author. The number of not-treated books didn't appear at the total. It also deleted the total following main subject.

• 한국작물학회지
• /
• 제18권
• /
• pp.88-123
• /
• 1975

본 연구는 대맥의 다수확 재배기술 개선의 기초자료를 얻고져 작물시험장(수원) 맥류포장에서 수원18호를 공시하여 1969년부터 1970년까지 2개년간 시비량, 파종기 및 파종량을 달리 하여 이들 처리가 수량 및 수량구성요소에 미치는 영향과 이들의 형성과정을 추구하였으며 또한 수원18호외 7품종을 공시하여 파종기이동에 따른 품종들의 수량 및 수량 구성요소의 변화를 검토한바 그 결과를 요약하면 다음과 같다. 1. 수원에서 대맥 수원 18호의 출현이수는 파종기 (9월 21일에서 10월 31일까지)에 따라 8~19일정도 소요되었고 조파할수록 빠른 경향을 보였으며 대체로 지중 5cm의 적산온도가 15$0^{\circ}C$내외면 출현하였다. 2. 파종기에 따른 냉해정도의 차이는 월동기간의 대맥 생육정도와 기상조건의 영향이 크며 월동전 생육이 과도하거나 주간출엽수가 5~6엽에 미달되면 냉해에 약하였다. 3. 주간출엽수는 파종기에 따라 11매로부터 16매까지 변화하지만 대체로 원동전 주간출엽수의 차이가 심하고 원동후 주간출엽수의 차이는 적으며 특히 9월 21일 파종부터 10월 11일 파종까지의 주간출엽수의 차이는 월동전 주간출엽수의 차이에 의하여 나타났다. 4. 월동전 지상부 건물생산량은 조파구에서 많고 만파할수록 적었으나 월동후에는 파종기에 따른 지상부 건물생산량의 차이가 적었으며 생육 재생기부터 출수기까지는 건물생산량이 급증하고 등숙기간에는 증가율이 낮았다. 5. 1$\m^2$당 경수는 대체로 조파한 것이 만파한 것보다, 후파한 것이 박파한 것보다 많았다. 개체당 분얼은 후파할 때는 적고 파종기에 따른 차이는 미미하였으나 박파하였을 때는 파종기에 따른 변이가 컸다. 조파에서는 파종량이 많아 질수록 개체당 분얼수가 현저히 감소되나 만파시에는 파종량의 영향이 적었다. 6. 최고분얼기는 조파할 경우에 일찍 오고 만파할 경우에 늦게 오며 파종량에 따른 차이가 크지는 않았으나 대체로 파종량이 많을수록 빨리 오는 경향이었다. 7. 분얼최성기는 파종기에 관계없이 주간출엽수가 4~6매일 때이었다. 8. 1$\m^2$당수수는 해에 따라 차이가 있으나 시비량이나 파종량이 증가할수록 많아졌으며 시비량과 파종량을 함께 증가할 때에는 수수의 확보가 용이하고 이러한 경향은 특히 적기파종에서 컸다. 또한 많은 수수를 확보하는 데는 적기 파종이 파종량 증가보다 중요하고 만파시에는 파종량을 증가시키는 것이 유리하였다. 9. 품종별 파종기에 따른 1$\m^2$당 수수는 대체로 모든 품종에서 만파할수록 감소되었으나 수원18호, 여기, 항미, 부흥는 수원 004, 수원006 칠보 및 영월 6각보다 만파에 의한 감소율이 적었다. 10. 1$\m^2$당 수수와 1$\m^2$당 경수와의 상관 관계를 보면 9월 21일 파종에서는 출수기부터, 10월 1일 파종에서는 월동전에, 10월 11일 파종부터 10월 31일 파종까지는 전 생육기간에서 대체로 높은 정의 상관이 있었으며 3월 하순부터 4월 상순까지는 어느 파종기에서나 상관정도가 낮았다. 11. 유효경 비율은 파종기 및 파종량에 따라 33~76%까지의 넓은 변이폭을 보였으며 50%정도에서 수량이 가장 높았고 파종량에 따른 변이폭보다 파종기에 따른 변이폭이 컸다. 또한 조파에서 유효경 비율이 낮고 만파일수록 높아 가는 경향이었으며 파종량이 증가하면 유효경 비율이 다소 감소하는 경향이었다. 품종별로는 수원18호, 항미, 여기 및 부흥는 유효경 비율이 높으며 이들 품종들은 만파할 경우의 증가율이 컸고 칠보, 수원004, 수원006, 영월6각은 유효경 비율이 낮고 만파에 의한 증가율도 낮았다. 12. 1수립수는 어느 경우에나 시비량이 증가할수록 증가하였고 파종량이 증가할수록 감소하였으며 파종기에 따라서는 10월 21일(1969), 10월 1일(1970)파종에서 1수립수가 가장 적었으며 이보다 조파하거나 만파할수록 증가하였다. 한편 품종별로는 파종기에 따른 경향이 일정하지 않았다. 13. 천립중은 1$\m^2$당 수수와 1수립수에 비하여 시비량, 파종기 및 파종량 차이에 따른 변이폭이 작았으나 년차변이는 컸으며, 파종량이 증가할수록 천립중은 다소 감소하였다. 품종별로는 차이가 뚜렷하여 부흥과 칠보는 대체로 무거웠고 수원18호, 항미 및 여기는 비교적 가벼웠다. 14. 수원지방의 파종적기는 10월 1일~10월 11일로 인정되었고, 시비량 증가에 따라 수량은 대체로 증가하였으며 조기 파종시의 수량감소를 비료증가로 다소 경감시킬 수 있었다. 15. 파종량 차이에 따른 수량의 변이폭은 시비량이나 파종기차이에 따른 변이폭보다 비교적 적었고, 조파나 소비조건에서는 파종량 차이에 따른 수량 변이가 미미하였다. 또한 파종량은 증가시킬 경우 증비의 효과가 크며 만파시에는 파종량의 증가로 수량의 심한 감소를 보상할 수 있었다. 16. 적정 파종량은 시비량 증감에 따라 다소 차이가 있었으나 10a당 시비량 10.5-6.6kg 수준에서는 10a당 파종량을 18~26$\ell$까지 증가시키는 것이 수량의 안정을 기할 수 있었다. 17. 파종적기는 품종별로 다소 달랐으며, 수원006 수원004 및 부흥은 비교적 조기 파종에서 증수되었고 수원18호, 여기 및 항미는 19월 1일경 파종에서 증수를 보였으며 부흥은 만파 적응성이 높았다. 18. 수량과 수수와는 모든 처리에서 고도의 정상관을 보였는데 시비량이 증가할수록 상관이 높아졌고 파종량이 증가할수록 수량과 수수의 상관은 낮았다. 수량과 1수립수는 대체로 부의 상관을 보였으며 천립중과 수량과는 상관 정도가 낮았다.

• 한국산림과학회지
• /
• 제9권1호
• /
• pp.1-44
• /
• 1969

이상(以上)과 같이 조사(調査) 또는 실험(實驗)한 결과중(結果中) 그 중요(重要)한 것을 요약(要約)하면 다음과 같다. 1. 실험용(實驗用) 지상식(地上式) 양송이 재배사(栽培舍)의 효과(効果)에 관(關)하여는 이미 실험결과(實驗結果)및 그 분석(分析)에서 지적(指摘)된 바 있거니와 그 측벽(側壁)및 천정(天井)의 구조(構造)는 재배사(栽培舍)를 외계(外界)의 기상조건(氣象條件)에서 격리(隔離)하는데 충분(充分)한 효과(効果)가 있는 것으로 고려(考慮)된다. 2. 반지하실(半地下室)에 구축(構築)한 실험용(實驗用) 태양식(太陽式) 양송이 재배사(栽培舍)의 효과(効果)에 관(關)하여는 실험결과(實驗結果)및 그 분석(分析)에서 지적(指摘)한 바와 같거니와 태양열(太陽熱)을 이용(利用)하는데 있어 충분(充分)한 효과(効果)가 있는 것으로 고려(考慮)된다. 그러나 이것을 농가(農家)에 적용(適用)하기 위(爲)하여는 다음과 같은 제점(諸點)이 개선(改善)되어야 할 것으로 고려(考慮)된다. 즉 (1) 태양식(太陽式)의 지붕과 천정(天井)은 실험용(實驗用) 지상식(地上式) 재배사(栽培舍)의 그것과 동일(同一)히 하고 (2) 태양열(太陽熱) 수열장치(受熱裝置)는 적당(適當)히 재고(再考)되어야 할 것으로 고려(考慮)된다. 태양열(太陽熱) 수열장치(受熱裝置)는 그림 40과 같이 하면 유효(有效)할 것으로 구상(構想)된다. 3. 본실험연구(本實驗硏究)에서 실시(實施)한 각종(各種)의 환기법중(換氣法中) G.E.-C.V. 및 V.S.-C.V. 환기법(換氣法)이 가장 효과적(效果的)인 것으로 본다. 4. 측벽수직(側壁垂直)및 지중(地中) 환기장치(換氣裝置)는 이미 지적(指摘)된 바와 같이 농가(農家) 양송이 재배사(栽培舍)의 자연환기법(自然換氣法)으로 실용적(實用的) 가치(價値)가 충분(充分)하다. 그것은 이들 환기장치(換氣裝置)는 그 환기로(換氣路)를 통(通)하여 사내(舍內)에 유입(流入)되는 외기(外氣)의 온도(溫度)를 인공적(人工的)으로 가열(加熱)이나 또는 냉각(冷却)하지 않고 사내온도(舍內溫度)에 접근(接近)하도록 조절(調節)하는 효과(効果)가 있기 때문이다. 지금 외온(外溫)을 $X^{\circ}C$로 할 때 각종(各種) 환기로(換氣路)에 의(依)하여 흡수(吸收)되는 온도(溫度) $Y^{\circ}C$을 X의 흉수(凶數)로 하는 실험식(實驗式)은 다음과 같이 회귀직선(回歸直線)으로 표시(表示)된다. $$G.P.{\cdots}Y=0.9x-12.8$$ $$G.E.{\cdots}Y=0.96x-15.11$$ $$V.S.{\cdots}Y=0.94x-17.57$$ 5. 재배사내(栽培舍內)에 유입(流入)되는 공기(空氣)및 사외(舍外)로 배출(排出)되는 공기(空氣)에 관(關)한 실험식(實驗式)은 각각(各各) 다음과 같이 회귀직선(回歸直線)및 지수곡선(指數曲線)으로 표시(表示)된다. (1) 배출속도(排出速度) Ycm/Sec를 유입속도(流入速度)${\times}$cm/Sec의 흉수(凶數)로 하는 회귀직선식(回歸直線式) G.E.-C.V.(50%)법(法) $${\cdots}Y=1.01x-1.65$$ G.E.-C.V.(100%)법(法)$${\cdots}Y=0.42x+2.03$$ V.S.-C.V.(100%)법(法)Y=0.85x+0.96 (2) 배출량(排出量) Y $m^3/hr$ 유출량(流出量) ${\times}m^3/hr$의 함수(凾數)로 하는 회귀직선식(回歸直線式) G.E.-C.V.(50%)법(法)$${\cdots}Y=2.59x-10.88$$ G.E.-C.V.(10%)법(法)Y=2.16x+26.53 (3) 상면(床面) 공기이동(空氣移動) 속기(速氣) Y m/Sec를 배출공기(排出空氣) 속도(速度)${\times}$m/Sec의 함수(凾數)로 하는 회귀직선식(回歸直線式) G.E.-C.V.(50%)법(法)$${\cdots}Y=0.54x+0.84$$ (4) $Co_2$ 축적량(蓄積量)Y(%)를 상면(床面) 공기이동(空氣移動) 속도(速度)${\times}$cm/Sec의 함수(凾數)로 하는 회귀직선식(回歸直線式) G.E.-C.V(50%)법(法)$${\cdots}Y=114.53-6.42x$$ (5) $Co_2$ 축적량(蓄積量)Y(%)를 배출(排出) 공기량(空氣量) $m^3/hr$ 함수(凾數)로 하는 지수곡선식(指數曲線式) G.E.-C.V.(50%)법(法) -$$y=127.18{\times}1.0093^{-X}$$ (6) natural vontilation system에 있어서 양송이 생육(生育)에 적합(適合)한 환경적조건(環境的條件)을 마련하기 위(爲)한 환기구(換氣口)의 단면적(斷面績)은 재배사(栽培舍) 전용적(全容積)에 대(對)하여 다음과 같은 비율(比率)로 할 수 있다. G.E. (지중유입환기구단면적(地中流入換氣口斷面績) $${\cdots}0.3-0.5%$$(요조절(要調節)) C.V. (천정배출환기구단면적(天井排出換氣口斷面績) $${\cdots}0.8-1.0%$$(요조절(要調節)) (7) 본연구(本硏究)에서 실험(實驗)한 각종(各種)의 가열장치중(加熱裝置中) 무압(無壓) 증기수(蒸氣水) 보이라로 사용(使用)할 수 있는 온수(溫水) 보이라가 농가용(農家用) 양송이 재배사(栽培舍) 가열장치(加熱裝置)로서, 그 효과면(効果面)에 있어서나 또는 그가격면(價格面)에 있어서 최적합(最適合)하다는 것이 확인(確認)되고 있다.

• Journal of the Korean Wood Science and Technology
• /
• 제13권1호
• /
• pp.19-62
• /
• 1985

본(本) 시험(試驗)은 국내(國內) 활엽수로서 중요한 참나무속(屬)의 상수리나무와 침엽수(針葉樹)의 대표적(代表的) 수종(樹種)인 소나무를 공시목(公試木)으로 선정(選定)하여 곡목가공분야(曲木加工分野)에서 널리 이용(利用)하는 자비법(煮沸法)과 증자법(蒸煮法)에 의한 휨가공성(加工性)을 조사(調査)하고, 이에 관련(關聯)된 인자(因子)로서 변(邊) 심재(心材), 연륜각도(年輪角度), 연화처리온도(軟化處理溫度), 연화처리시간(軟化處理時間), 목재함수율(木材含水率) 및 목재결함(木材缺陷) 등(等)의 영향(影響)과 휨가공(加工)후의 곡율반경변화(曲率半經變化) 및 약제처리(藥劑處理)에 의한 휨가공성(加工性)의 개선방법(改善方法)을 구명(究明)하기 위하여 실시(實施)되었다. 이 때 사용(使用)된 자비(煮沸)와 증자처리용(蒸煮處理用) 시편(試片)의 크기는 두께와 너비 15mm, 길이 350mm이고 약제처리용시편(藥劑處理試片)의 크기는 두께 5mm, 너비 10mm 및 길이 200mm로 제작(製作)하였으며, 시편(試片)의 함수율(含水率)은 자비처리(煮沸處理)에는 생재(生材)를 사용(使用)하고 증자처리(蒸煮處理)에는 15%로 조습(調濕)된 건조재(乾燥材)를 사용(使用)하였다. 또한 약제처리(藥劑處理)는 포화요소용액(飽和尿素溶液), 35% 포르말린 용액(溶液), 25% 폴리에칠렌(400) 수용액(水溶液) 및 25% 암모니아수에 5일간(日間) 상온(常溫)으로 침지(浸漬)한 우 휨가공(加工)을 행하였다. 본(本) 시험(試驗)에서 얻은 결과(結果)를 요약(要約)하면 다음과 같다. 1. 상수리나무와 소나무의 목재내부온도(木材內部溫度)는 자비(煮沸) 또는 증자처리시간(蒸煮處理時間)에 따라 초기(初期) 약(約) $30^{\circ}C$까지 완만(緩慢)한 상승(上昇)을 보이다가 그 후 직선적(直線的)으로 급상승(急上昇)하며 후기(後期) $80{\sim}90^{\circ}C$부터는 다시 완만(緩慢)해지는 경향(傾向)을 나타냈다. 2. 최종온도(最終溫度) $100^{\circ}C$까지 도달(到達)하는 데 소요(所要)되는 연화처리시간(軟化處理時間)은 목재(木材)의 두께에 비례(比例)하며 두께 15mm 각재(角材)에 대한 $25^{\circ}C$에서 $100^{\circ}C$까지의 소요시간(所要時間)은 상수리나무 9.6~11.2분(分), 소나무 7.6~8.1분(分)으로서 소나무의 연화속도(軟化速度)가 보다 빠르게 나타났다. 3. 증자처리시간(蒸煮處理時間)의 경과(經過)에 따른 목재(木材)의 함수율증가경향(含水率增加傾向)은 처음 약(約)4분(分)까지 급증(急增)하나 그후 점차(漸次) 둔화(鈍化)되어 상수리나무는 20분(分), 소나무는 15분경(分頃)부터 거의 직선적(直線的)으로 완만(緩慢)하게 증가(增加)하는 경향(傾向)을 나타냈다. 두께 15mm 각재(角材)에 대한 초기함수율(初期含水率) 15%에서 50분간(分間) 증자처리(蒸煮處理) 후의 함수율증가량(含水率增加量)은 상수리나무 3.6%, 소나무 7.4%로서 소나무의 흡습속도(吸濕速度)가 빠르게 나타났다. 4. 자비처리시간(煮沸處理時間)이 경과(經過)함에 따라 두 수종(樹種) 모두 기계적(機械的) 성질(性質)이 현저하게 감소(減少)하였으며, 60분간(分間) 자비처리(煮沸處理)에 의한 기계적(機械的) 성질(性質)의 감소율)減少率)은 압축강도(壓縮强度) 35.6~45.0%, 인장간도(引張强度) 12.5~17.5%, 휨강도(强度) 31.6~40.9% 및 휨탄성계수(彈性係數) 23.3~34.6%로 나타났다. 5. 변재(邊材)와 심재별(心材別) 최소곡률반경(最小曲律半徑)은 각각(各各) 상수리나무에서 60~80mm 및 90mm, 소나무에서 260~300mm 및 280~300mm로 두 수종(樹種) 모두 변재(邊材)의 휨가공성(加工性)이 양호하였다. 6. 상수리나무의 정목재(柾木材)와 판목재별(板目材別) 최소곡률반경(最小曲律半徑)은 모두 60~80mm로서 차이(差異)가 없었으나 소나무에서는 각각(各各) 240~280mm 및 260~300mm로 정목재(柾木材) 휨가공성(加工性)이 양호하였다. 7. 연화처리온도(軟化處理溫度)가 증가(增加)할수록 상수리나무와 소나무 모두 휨가공성(加工性)이 향상(向上)되었으며 휨가공(加工)을 위한 최저처리온도(最低處理溫度)는 각각(各各) $90^{\circ}C$ 및 $80^{\circ}C$로서 처리온도(處理溫度)에 대한 의존도(依存度)는 상수리나무에서 약간 높게 나타났다. 8. 연화처리시간(軟化處理時間)이 증가(增加)할수록 상승온도(上昇溫度)와 상응(相應)하여 휨가공성(加工性)을 향상(向上)시켰으나 최종온도(最終溫度)에 도달(到達)한 후에도 계속 연화(軟化)을 지속(持續)해야 비로서 최적연화상태(最適軟化狀態)를 나타냈다. 휨가공(加工)을 위한 최소처리시간(最少處理時間) 두께 15mm 각재(角材)에 대하여 상수리나무에서 자비처리시(煮沸處理時) 10분(分), 증자처리시(蒸煮處理時) 30분(分) 및 소나무에서 자비처리시(煮沸處理時) 10분(分), 증자처리시(蒸煮處理時) 20분(分)으로 나타났다. 9. 휨가공(加工)을 위한 상수리나무의 적정함수율(適定含水率)은 20%로 나타났으며 섬유포화점(纖維飽和點) 이상(以上)에서는 오히려 휨가공성(加工性)이 저하(低下)되었다. 반면(反面)에 소나무의 적정함수율(適定含水率)은 30% 이상(以上)을 필요(必要)로 하였다. 10. 본(本) 시험(試驗)에서 얻은 최적조건(最適條件)(Table 19)으로 휨가공(加工)을 실시(實施)한 결과(結果) 상수리나무의 최소곡률반경(最小曲律半徑)은 자비처리시(煮沸處理時) 80 mm, 증자처리시(蒸煮處理時) 50 mm이고 소나무에서는 자비처리시(煮沸處理時) 240 mm, 증자처리시(蒸煮處理時) 280 mm로서 상수리나무는 증자처리(蒸煮處理)의 연화효과(軟化效果)가 양호하였으나 소나무는 자비처리(煮沸處理)가 양호하였다. 11. 인장대철(引張帶鐵) 사용(使用)하지 않았을 경우 상수리나무와 소나무의 시편(試片)두께(t)와 최소곡률반경(最小曲律半徑)(r)의 비(比)(r/t)는 각각(各各) 자비처리시(煮沸處理時) 16.0 및 21.3, 증자처리시(蒸煮處理時) 17.3 및 24.0으로 나타났으나 인장대철(引張帶鐵) 사용(使用)하였을 때는 각각(各各) 자비처리시(煮沸處理時) 5.3 및 16.0, 증자처리시(蒸煮處理時) 3.3 및 18.7로서 휨가공성(加工性)의 현저한 향상(向上)을 나타냈다. 12. 미소(微小)한 옹이의 위치별(位置別) 상수리나무의 휨가공성(加工性)에 미치는 영향(影響)은 매우 심하게 나타났는 데 특히 옹이의 의치(位置)를 휨재(材)의 압축측(壓縮側)에 두고 곡률반경(曲律半徑) 100 mm로 휨가공(加工)하였을 때는 파양율(破壤率)이 90%로서 거의 휨가공(加工)이 불가능(不可能)하였다. 그러나 옹이를 인장측(引張側)에 두었을 경우에는 파양율(破壤率)이 10%에 불과(不過)하였다. 13. 곡률반경(曲律半徑) 300 mm로 휨가공(加工) 후 30 일간(日間) 실내조건(室內條件)에서 방치(放置)하였을 때의 곡률반경변화율(曲律半徑變化率)은 자비처리시(煮沸處理時) 4.0~10.3%, 증자처리시(蒸煮處理時) 13.0~15.0%로서 증자처리(蒸煮處理)에 의한 복원현상(復元現象)이 자비처리(煮沸處理)보다 심하게 나타났으며 에폭시수지(樹脂)를 도포(塗布)하여 방습처리(防濕處理) 하였을 경우에는 곡률반경변화율(曲律半徑變化率)이 -10~0%에 불과(不過)하였다. 14. 약제처리(藥劑處理)에 의한 가소성(可塑性) 효과(效果)는 35% 포르말린 용액(溶液)과 25% 폴리에칠렌 글리콜(400) 수용액(水溶液)에서는 나타나지 않았고 포화요소용액(飽和尿素溶液)과 25% 암모니아수에서는 나타났으나 증자처리(蒸煮處理)의 효과(效果)에는 미치지 못하였다. 그러나 약제처리(藥劑處理) 후 증자처리(蒸煮處理)를 병용실시(倂用實施)하였을 때는 증자처리(蒸煮處理)보다 10~24% 휨가공성(加工性)이 향상(向上)되었다. 15. 소서계수(塑性係數)와 곡률반경(曲律半徑)과의 관계(關係)는 하중(荷重)-변형계수(變形係數), 변형계수(變形係數) 및 에너지계수(係數) 모두 1% 수준(水準)에서 유의적(有意的)인 상관(相關)이 인정(認定)되므로 휨 가공용재(加工用材)의 품질지표(品質指標)로서 적합(適合)하였고 적합도(適合度)는 하중(荷重)-변형계수(變形係數), 에너지계수(係數) 및 변형계수(變形係數)의 순(順)으로 크게 나타났다.