• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.234-239
• /
• 2000

The capillary pumped cooling system (CPCS) is a cooling system which controls temperature of the small electronic devices, such as IC device systems, notebook computers, etc. An important feature of CPCS is that a working fluid circulates in a system by capillary force in tubes instead of mechanical input power. The cooling effect of CPCS is investigated with respect to heat flux, condensation temperature under different working fluids (water, ethanol, methanol). Capillary pumped flows are visualized under various conditions and mass flow rate and temperature are experimentally measured. It is shown that the increasing tendency of mass flux for each working fluid is observed as the temperature of evaporator increases, and that the cooling possibility of CPCS depends on the performance of evaparator and condenser which sustains the steady state temperature continuously.

• Journal of the Korean Society of Safety
• /
• v.16 no.4
• /
• pp.14-21
• /
• 2001

SG-365 steel is an important material End used for manufacturing a pressure vessel and gas piping. In this investigation, the elastic plastic fracture toughness of this material is evaluated by the unloading compliance method according to the ASTM E8l3-97 and E1152-97 method on the smooth and side groove In specimens. The effect of smooth and side groove is studied on the elastic plastic fracture toughness. The side grooved specimen is very useful in estimation of the $J_{IC}$. Because it is much easier than the smooth specimen to the onset of the ductile tearing by the R curve method. Besides. it improves the accuracy of toughness values, decreases the scattering of them and crack tunneling effect and shear lip by the side groove.

• Electronics and Telecommunications Trends
• /
• v.36 no.4
• /
• pp.61-71
• /
• 2021

Navigation satellite systems (GPS, GLONASS etc.) provide three main services, i.e., positioning for location based services, navigation for multi-modal transportation services, and timing for communication and critical infrastructure services. They were started as military systems but were extended to civil service. Navigation satellite navigation system began with GPS in the USA and GLONASS in Russia at nearly the same time. Indian NavIC and Chines BDS announced their FOCs in 2016 and 2020, respectively and European Galileo and Japanese QZSS are catching up others. In these days, Navigation Satellite System, Positioning, Navigation, and Timing services are part of our daily life very closely. They are required for autonomous driving car, Unmanned vehicles like UAV, UGV, and UMV, 5G/6G telecommunications, world financial system, power system, survey, agriculture, and so on. The services among navigation satellite systems are very competitive and also cooperative one another. This article describes the status of these systems and evolution in the technical and service senses, which may be helpful for planning korea positioning system(KPS).

• Proceedings of the Korean Society of Plant Pathology Conference
• /
• 2003.10a
• /
• pp.127.2-127
• /
• 2003

YMV-K strains were purified from D. oppostita Thunb. tv. Dung-Gun-Ma showing mosaic symptom on their leaves. YMV-K strains were filamentous particles of 780nm in length and induced cytoplasmic disorder such as inclusion body formation. Nucleotide and amino acid sequences of 5'-UTR, Pl and CP of YMV-K strains shared 80.8, 64.7 and 98.3％ identity respectively to JYMV J1 in the mean value. Purification of YMV-K strains according to JYMV purification method(S. Fuji) was conducted to product antiserum. With antiserum against YMV-K strains, the Various diagnosis methods such as IC-RT-PCR, DIBA, RIPA and indirect-ELISA were used to detect YMV-K strains in Chinese yam plant.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.4
• /
• pp.488-503
• /
• 1999

The present paper considers the constraint effect on J-R curves under the two-parameter $J-A_2$ controlled crack growth within a certain amount of crack extension. Since the parameter $A_2$ in $J-A_2$ three-term solution is independent of applied loading under fully plasticity or large-scale defor-mation $A_2$ is a proper constraint parameter uring crack extension. Both J and $A_2$ are used to char-acterize the resistance curves of ductile crack growth using J as the loading level and $A_2$ are used to char-acterize the resistance curves of ductile crack growth using J as the loading level and A2 as a con-straint parameter. Approach of the constraint-corrected J-R curve is proposed and a procedure of transferring the J-R curves determined from standard ASTM procedure to non-standard speci-mens or real cracked structures is outlined. The test data(e.g. initiation toughness JIC and tearing modulus $T_R$) of Joyce and Link(Engineer-ing Fracture Mechanics 1997, 57(4) : 431-446) for single-edge notched bend[SENB] specimen with from shallow to deep cracks is employed to demonstrate the efficiency of the present approach. The variation of $J_{IC}$ and $T_R$ with the constraint parameter $A_2$ is obtained and a con-straint-corrected J-R curves is constructed for the test material of HY80 steel. Comparisons show that the predicted J-R curves can very well match with the experimental data for both deep and shallow cracked specimens over a reasonably large amount of crack extension. Finally the present constraint-corrected J-R curve is used to predict the crack growth resistance curves for different fracture specimens. over a reasonably large amount of crack extension. Finally the present constraint-corrected J-R curve is used to predict the crack growth resistance curves for different fracture specimens. The constraint effects of specimen types and specimen sizes on the J-R curves can be easily obtained from the constrain-corrected J-R curves.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.27 no.4
• /
• pp.373-379
• /
• 1994

Final biomass yields(cells/ml) and growth rates(divisions/day) of 4 clones of marine diatoms isolated from the Korean coastal waters were measured in media with 6 different levels of added cadmium concentrations. A neritic diatom, GS-12(Chaetoceros sp.), showed no growth at 0.1ppm cadmium, and its $IC_{50}$ for final biomass yield and growth rate was 0.03 and 0.02ppm, respectively. Two clones isolated from tidal pool, NC-37 and NC-29, showed enhanced tolerance to cadmium toxicity. Extremely high tolerance to cadmium addition was found in J-21 from a eutrophicated bay, with its high $IC_{50}$ for biomass yield(1.07ppm) and growth rate(1.92ppm). Present results implied a habitat related pattern of coastal diatom clones in the cadmium tolerances. Except GS-12, the other three diatom clones are considered to be highly tolerant to cadmium stresses.

• Journal of Nutrition and Health
• /
• v.38 no.10
• /
• pp.880-894
• /
• 2005

The purposes of this study were to a) measure the IC identified of CFMC (contract foodservice management company) ,b) examine IC circumstance of CFMC, c) evaluate practically IC measurement tool of CFMC, and d) present information for selecting an adequate CFMC to clients. The questionnaires of IC measurement were handed out to 108 CFMCs, there composing of main office employees, foodservice managers, customers, and clients of 207 school,38 hospital, and 86 husiness/industry foodservices. The statistical data analysis was completed using SPSS Win (ver 12.0) for descriptive analysis, t-test, Mann-Whitney U test. First, CFMCs had operational experience for an average of 8 years and 8 months, and served an average of 38,540 meals a day. Most of the respondent companies specialized in the school foodservice field and managed an average of 66 clients for the contract period of 2 years and 3 months. Second, the respondent companies had gotten a score of 77.78 points for the total average, 77.7 points in the large enterprise group and 78.1 points in the small and medium-sized enterprise group. Therefore, the minimum number of points for the accrediting license on Qualification is suggested to be over 70 out of a 100 point scale; this study would be serve as reference for the certification license on qualification. On the level of evaluation category, the scores were 14.15 to 20 points on $\ulcorner$finance$\urcorner$, 19.24 to 25 points on $\ulcorner$customer$\urcorner$, 19.33 to 25 points on $\ulcorner$process$\urcorner$, 14.31 to 20 points on $\ulcorner$human resource$\urcorner$, and 8.6 to 10 point on $\ulcorner$renewal and development$\urcorner$ . $\ulcorner$Renewal and development$\urcorner$ and $\ulcorner$customer focus$\urcorner$ received better grades than other evaluation categories. Third, $\ulcorner$Finance$\urcorner$ indicated similar distribution overall. Small and medium-sized companies had lower grades than large companies on 'market ability' of $\ulcorner$customer$\urcorner$ , but, clients of small and medium-sized companies had higher grade for 'client satisfaction' than large companies. Most of the companies supported 'infrastructure support for foodservice operation' of $\ulcorner$process$\urcorner$ by the main office of CFMCs, but, the branch chain offices of CFMCs were not applied efficiently. Large companies made more effort to improve the 'employee ability' of $\ulcorner$human focus$\urcorner$ than small and medium-sized CFMC. The 'research and development cost' of $\ulcorner$renewal and development$\urcorner$ was increased compared to the previous year. In conclusion, if CFMCs were to perform self-evaluation and a routine checkups by utilizing CFMC's IC measuring tool, improvements in CFMC operational capacities as well as foodservice quality can be noted. (Korean J Nutrition 38(10)'880$\sim$894,2005)

• Electronics and Telecommunications Trends
• /
• v.4 no.4
• /
• pp.108-134
• /
• 1989

본 고는 현재 공중회선망을 이용한 PC 통신에 필수장비인 모뎀을 구성하는 2,400bps Modem Chip Set을 비교하였다. 현재 널리 사용되는 Modem Chip Set들은 주로 2-3개 Chip으로 구성되며, 이것들을 사용하여 완전한 2,400bps Modem을 구성할 수 있다. 이러한 모뎀용 IC는 PC통신뿐만 아니라 휴대용 Terminal, 차량추적시스팀, 휴대용 전화기, 각종 원격검침계량기 등에서와 같이 그 사용범위가 다양화되고 있는 추세이다.

• Electronics and Telecommunications Trends
• /
• v.28 no.6
• /
• pp.206-216
• /
• 2013

전력반도체는 전력을 시스템에 맞게 배분하는 제어와 변환기능을 가진 소자이며, 에너지를 절약하고 제품을 축소하기 위하여 전력공급 장치나 전력변환 장치에 사용된다. 최근에는 모바일 기기의 증가와 전기자동차의 개발과 맞물려 전력반도체 적용 영역이 확대되고 있다. 선진국들은 산 학 연 관 중심으로 에너지를 절감할 수 있는 친환경 절전형 전력소자 공정, 회로, 모듈 및 시스템 기술 개발에 집중하고 있다. 국내는 원천기술 부족과 해외 특허 등으로 인해 90% 이상을 수입에 의존하고, 기술수준은 선진국대비 50~70%에 불과할 정도로 매우 취약한 편이다.

• 한국초전도학회:학술대회논문집
• /
• v.11
• /
• pp.74-74
• /
• 2001