• Solar Energy
• /
• v.20 no.2
• /
• pp.43-54
• /
• 2000

We prepared and characterized $Cu(In_{1-x}Ga_x)Se_2$(CIGS) films using a elemental co-evaporation method for absorbing layer of high efficiency thin film solar cells. The CIGS films deposited on a soda-lime glass exhibited low resistivity because of higher carrier concentration. Na was accumulated at the CIGS surface and the 0 and Se were also accumulated at the surface, suggesting that oxidation is a driving force of Na accumulation. The structure of CIGS film was modified or a secondary phase was formed in the Cu-poor CIGS bulk films probably due to the incorporation of Na into Cu vacancy sites. As the Ga/(In+Ga) ratio increased, the diffraction peaks of $Cu(In_{1-x}Ga_x)Se_2$ films were shifted to larger angle and splitted, and the grain size of $Cu_{0.91}(In_{1-x}Ga_x)Se_2$ films became smaller. All $Cu_{0.91}(In_{1-x}Ga_x)Se_2$ films showed the p-type conductivity regardless of the Ga/(In+Ga) ratio. Ag/n-ZnO/i-ZnO/CdS/$Cu_{0.91}(In_{0.7}Ga_{0.3})Se_2$/Mo solar cells were fabricated. The currently best efficiency in this study was 14.48% for $0.18cm^2$ area ($V_{oc}=581.5mV,\;J_{sc}=34.88mA$, F.F=0.714).

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.10 no.1
• /
• pp.42-48
• /
• 2011

In this paper, a passive load-pull using a GaN HEMT (Gallium Nitride High Electron Mobility Transistor) bare-chip in X-band is presented. To obtain operation conditions that characteristic change by self-heating was minimized, pulsed drain bias voltage and pulsed-RF signal is employed. An accuracy impedance matching circuits considered parasitic components such as wire-bonding effect at the boundary of the drain is accomplished through the use of a electro-magnetic simulation and a circuit simulation. The microstrip line length-tunable matching circuit is employed to adjust the impedance. The measured maximum output power and drain efficiency of the pulsed load-pull are 42.46 dBm and 58.7%, respectively, across the 8.5-9.2 GHz band.

• Proceedings of the KIPE Conference
• /
• 2018.11a
• /
• pp.193-194
• /
• 2018

본 논문은 $6kW/L(98W/in^3)$의 전력밀도를 갖는 xEV LDC를 위한 절연형 DC-DC컨버터의 설계 방법을 제안한다. 부피를 가장 많이 차지하는 수동소자의 부피를 줄이기 위해 GaN소자를 적용하여 스위칭 주파수를 700kHz를 적용하였다. 또한 자속 상쇄 개념이 적용된 매트릭스 평면 변압기를 적용하여 변압기의 부피를 크게 줄일 수 있었다. 본 논문에서는 후보 토폴로지들의 비교를 통해 고 전력 밀도에 가장 적합한 토폴로지를 선정하였으며, 자속상쇄 개념 기반의 매트릭스 평면 변압기를 설계방법을 제안하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.287.1-287.1
• /
• 2016

Three-dimensional (3-D) semiconductor nanoarchitectures, including nano- and micro- rods, pyramids, and disks, are emerging as one of the most promising elements for future optoelectronic devices. Since these 3-D semiconductor nanoarchitectures have many interesting unconventional properties, including the use of large light-emitting surface area and semipolar/nonpolar nano- or micro-facets, numerous studies reported on novel device applications of these 3-D nanoarchitectures. In particular, 3-D nanoarchitecture devices can have noticeably different current spreading characteristics compared with conventional thin film devices, due to their elaborate 3-D geometry. Utilizing this feature in a highly controlled manner, color-tunable light-emitting diodes (LEDs) were demonstrated by controlling the spatial distribution of current density over the multifaceted GaN LEDs. Meanwhile, for the fabrication of high brightness, single color emitting LEDs or laser diodes, uniform and high density of electrical current must be injected into the entire active layers of the nanoarchitecture devices. Here, we report on a new device structure to inject uniform and high density of electrical current through the 3-D semiconductor nanoarchitecture LEDs using metal core inside microtube LEDs. In this work, we report the fabrications and characteristics of metal-cored coaxial $GaN/In_xGa_{1-x}N$ microtube LEDs. For the fabrication of metal-cored microtube LEDs, $GaN/In_xGa_{1-x}N/ZnO$ coaxial microtube LED arrays grown on an n-GaN/c-Al2O3 substrate were lifted-off from the substrate by wet chemical etching of sacrificial ZnO microtubes and $SiO_2$ layer. The chemically lifted-off layer of LEDs were then stamped upside down on another supporting substrates. Subsequently, Ti/Au and indium tin oxide were deposited on the inner shells of microtubes, forming n-type electrodes of the metal-cored LEDs. The device characteristics were investigated measuring electroluminescence and current-voltage characteristic curves and analyzed by computational modeling of current spreading characteristics.

• Journal of the Optical Society of Korea
• /
• v.20 no.1
• /
• pp.125-129
• /
• 2016

In this study, we have investigated a high-temperature AlN nucleation layer and AlGaN epilayers on c-plane sapphire substrate by low-pressure metal-organic chemical vapor deposition (LP-MOCVD). High resolution X-ray diffraction (HRXRD), atomic force microscopy (AFM), scanning electron microscope (SEM) and Raman scattering measurements have been exploited to study the crystal quality, surface morphology, and residual strain of the HT-AlN nucleation layer. These analyses reveal that the insertion of an LT-AlN nucleation layer can improve the crystal quality, smooth the surface morphology of the HT-AlN nucleation layer and further reduce the threading dislocation density of AlGaN epifilms. The mechanism of inserting an LT-AlN nucleation layer to enhance the optical properties of HT-AlN nucleation layer and AlGaN epifilm are discussed from the viewpoint of driving force of reaction in this paper.

• Bulletin of the Korean Chemical Society
• /
• v.18 no.3
• /
• pp.311-316
• /
• 1997

The synthesis and characterization of the mononuclear group 13 heterocyclic carboxaldehyde methyldithiocarbazate complexes Me2M[NC5H4CRNNC(S)SCH3] (M=Al, R=H(1); M=Ga, R=H(2); M=Al, R=CH3(3); M-Ga, R=CH3(4); M=In, R=CH3(5)) are described. Compounds 1-5 were prepared by the reaction of MMe3 (M=Al, Ga, In) with 2-formy or 2-acetylpyridine-S-methyldithiocarbazate in toluene. These compounds 1-5 have been characterized by microanalysis, NMR (1H, 13C) spectroscopy, mass spectra, and single-crystal X-ray diffraction. X-ray single-crystal diffraction analyses reveal that 4-5 are mononuclear metal compounds with coordination number of 5 and N,N,S coordination mode.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.339-342
• /
• 2007

$Cu(In_{1-x}Ga_{x})Se_2$(CIGS)는 매우 큰 광흡수계수를 가지고 있으므로 박막형 태양전지의 광흡수층 재료로서 많은 연구가 진행되고 있다. 박막이 태양전지의 광흡수층으로 이용되기 위해서는 큰 결정크기와 평탄한 표면, 적당한 전기적 특성을 가져야 한다. 이러한 특성들은 CIGS 박막의 조성에 큰 영향을 받고 있는 것으로 보고되고 있다. 본 연구에서는 동시증발법을 이용하여 Cu/(In+Ga) 비를 0.9로 고정한 후 Ga 조성(Ga/(In+Ga)의 비 : 0.32, 0.49, 0.69, 0.8, 1)을 변화시켜 Wide band gap CIGS 박막태양전지를 만들었다. 기판은 soda line glass를 사용하였고 뒷면 전극으로는 Mo를 스퍼터링법으로 증착하였다. 또한 버퍼층으로는 기존에 쓰이고 있는 CdS를 CBD(Chemical Bath Deposition)법으로 층착시켰으며, 윈도우층으로는 i-ZnO/n-ZnO를 스파터링 법으로 층착하였다. 그리고 앞면전극으로는 Al을 E-beam 으로 증착하였다. 분석은 XRD, SEM, QE로 분석하였다. 위 실험에서 얻은 결과로는 Ga/(In+Ga)비가 증가할수록 Cu(In,Ga)Se2 박막은 회절 peak들이 큰 회절각으로 이동하였고, 이것은 Ga 원자와 In 원자의 원자반경의 차이에서 기인된 것으로 사료된다. 또한 Ga 조성이 증가할수록 단파장 쪽으로 이동하는 것을 볼 수 있으며, Voc가 증가하다가 에너지 밴드캡이 1.62 eV 이상에서는 Voc가 감소하는 것을 볼 수 있는데 이것은 Ga 조성이 증가할수록 에너지 밴드캡이 커지면서 defect level 이 존재하기 때문인 것으로 사료된다. Ga/(In+Ga)비가 1일 때의 변환효율은 8.5 %이고， Voc : 0.74 (V), Jsc : 17.2 ($mA/cm^{2}$), F.F : 66.6(%) 이다.

• Proceedings of the KIEE Conference
• /
• 1988.11a
• /
• pp.168-171
• /
• 1988

The p-n homo junction diode of the III-V ternary alloy semiconductor $In_{1-x}Ga_xP$ : S grown by the temperature gradient solution (TGS) was fabricated by Zn-diffusion, and it's characteristics was investigated. The carrier concentration of $In_{1-x}Ga_xP$ doped with sulfur, 0.5 mol %, was $1{\times}10^{17}cm^{-3}$ and the mobility was varied with the composition. In the case that the diffusion time was constant as 30 minutes. The temperature dependence of diffusion coefficient was decreased from D= $4.2{\times}10^{-5}$ exp (-1.74/$k_{B}T$) to D= $2.5{\times}10^{-5}$ exp (-3.272/$k_{B}T$) with increasing of composition $\times$ from 0.43 to 0.98. The major peak of E.L spectrum was due to D-A pair recombination and the peak intensity was increased with the increasing of input current. And the E.L intensity was decreased with the increasing temperature, and shift to the long wavelength. The luminescence efficiencies measured at $5^{\circ}C$, atmosphere temperature, was decreased from $2.6{\times}10^{-4}$% to $9.49{\times}10^{-6}$ % with increasing of composition it from 0.39, direct transition region, to 0.98, indirect transition region.

• Proceeding of EDISON Challenge
• /
• 2017.03a
• /
• pp.428-432
• /
• 2017

Silicon 기반 Metal-oxide-semiconductor field-effect transistor (MOSFET)의 크기가 감소함에 따라 silicon자체의 물성적 한계가 나타나고 있다. 이를 극복하고자 III-V 화합물 반도체가 채널소자로서 각광받고 있다. 본 연구에서는 III-V 화합물반도체 중 $In_xGa_{1-x}As$는 Indium 조성에 따른 전자구조 및 n-type MOSFET의 소자 특성을 본다. Indium의 조성이 증가함에 따라 subband의 개수와 간격이 증가하게 되어 Density of state가 감소하게 된다. 이로 인하여 Indium의 조성이 증가함에 따라 $In_xGa_{1-x}As$ 채널 MOSFET에서 상대적으로 Fermi level을 더 많이 상승시키게 되어 potential barrier를 얇아지게 만들며 또한 에너지에 따른 전류 밀도를 넓게 분포하도록 만든다. 이로 인하여 단채널에서는 In 조성이 증가함에 따라 direct source-to-drain tunnelling current이 증가하게 된다. 이로 인하여 In 조성의 증가에 따라 subthreshold swing과 ON-state current가 저하된다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.2-2
• /
• 2010

텐덤형 태양전지는 다양한 에너지 대역을 동시에 흡수할 수 있도록 제작할 수 있어 단일접합 태양전지에 비해 높은 에너지변환효율을 기대할 수 있다. 본 연구에서는 GaAs를 기반으로 양자점 혹은 양자우물 구조를 이용한 고효율 텐덤형 태양전지를 설계하고, 완충층 및 활성층의 특성을 분석하였다. 분자선 단결정 성장 장비를 이용하여 GaAs 기판 위에 메타모픽 (metamorphic)성장법을 이용하여 convex, linear, concave 형태로 조성을 변화시켜 $In_xAl_1-_xAs$ 경사형 완충층을 성장한 후 그 특성을 비교하였다. 또한, 최적화된 경사형 완충층 위에 1.1 eV와 1.3 eV의 에너지 대역을 각각 흡수할 수 있는 적층 (5, 10, 15 층)된 InAs 양자점 구조 또는 InGaAs 양자우물구조를 삽입하여 p-n 접합을 성장하였다. 그리고 GaAs/AlGaAs층을 이용한 터널접합에서는 GaAs층의 두께 (20, 30, 50 nm)에 따른 터널링 효과를 평가하였다. 그 결과, 경사형 완충층을 통해 조성 변화로 인한 결함을 최소화하여 다양하게 조성 변화가 가능한 고품위의 구조를 선택적으로 성장할 수 있었으며, 적층의 양자점 구조 및 양자우물 구조를 이용해 고효율 텐덤형 태양전지의 구현 가능성을 확인하였다.