• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.96-96
• /
• 2009

투명전도막은 FPD의 전자부품에서 전극으로 널리 사용되고 있으며 현재 대부분의 투명전도막으로는 ITO가 사용되고 있다. 하지만, ITO에 사용되는 In은 희유금속으로 지속적인 사용량 증가로 가격의 급등과 더불어 수급 불안정으로 인해 In을 대체하고자 하는 연구가 집중적으로 이루어지고 있다. 그러나 $In_2O_3$를 대체한 ZnO계 등은 비저항이 높아 대체 적용이 가능하지 못하고 있다. 이에 In의 양을 줄이면서 상대적으로 저가이면서 광학적 특성이 우수한 ZnO을 첨가하여 기존의 ITO에 상응하는 전기전도도와 광투과율을 얻을 수 있는 새로운 3성분계 TCO 에 대한 연구가 활발히 이루어지고 있다. 따라서, 본 연구그룹은 $In_2O_3$을 기본 조성으로 하는 $In_2O_3-ZnO-SnO_2$계를 선정하여 IZTO target을 제조 후 RF magnetron sputtering 방법으로 투명전도막을 제작하였다. 본 연구에서는 RF 파워와 동작압력, 동작시간 그리고 열처리온도의 증착 조건에 따른 IZTO 박막의 특성을 평가하였다. 박막의 특성 및 표면 미세구조를 관찰하기 위해 AFM(Atomic Force Microscope)을 이용하였으며, XRD(X-ray diffraction)을 이용하여 결정성을 분석하였고, 4 point-prove, Hall effect measurement와 UV/Visible spectrometer를 통해 전기적, 광학적 특성을 평가하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.93-93
• /
• 2011

The Indium Zinc Tin Oxide (IZTO) and Indium Tin Oxide (ITO) thin films are grown on PI substrate at different substrate temperature by pulsed DC magnetron sputtering with a sintered ceramic target of IZTO (In2O3 70 wt.%, ZnO 15 wt.%, SnO2 15 wt.%) and ITO (In2O3 90wt.%, SnO2 10wt.%). The structural, electrical, and optical properties are investigated. The IZTO thin films deposited at low temperature showed relatively low electrical resistivity compared to ITO thin films deposited at low temperature. As a result, we could prepare the IZTO thin films with the resistivity as low as $5.6{\times}10^{-4}({\Omega}{\cdot}m)$. Both of the films deposited on PI substrate showed an average transmittance over 80% in visible range (400.800nm). Overall, IZTO thin film is a promising candidate as an alternative TCO material to ITO in flexible and OLED devices.

• Journal of the Korean Ceramic Society
• /
• v.42 no.6 s.277
• /
• pp.384-390
• /
• 2005

[ ${\alpha}-Al_2O_3$ ] precursor was synthesised by sol-gel method using aluminum sulfate, sodium sulfate and sodium carbonate as law materials. The flaky ${\alpha}-Al_2O_3$ crystals were prepared by heating using precursor about $1,050^{\circ}C$. In this study, the effect of some transition-metal sulfate ($FeSO_4,\;SnSO_4,\;ZnSO_4$) addition have been investigated. When iron sulfate was added, it could see that act on impurities in crystal growth process. In case of tin sulfate, distribution of Platelets was very broad. When flaky ${\alpha}-Al_2O_3$ crystals were prepared zinc sulfate addition, thickness, size, and distribution of platelets was suited to industrial application. The average diameter of flaky ${\alpha}-Al_2O_3$ crystals was about 20 $\mu$m, and its thickness was about 0.3 $\mu$m. Increasing addition of zinc sulfate, thickness of ${\alpha}-Al_2O_3$ platelet was decreased.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.92-92
• /
• 2011

IZTO and ITO thin films with a thickness of 200nm were deposited on Corning glass substrate to investigate the effects of substrate temperature on their electrical and optical properties by using pulsed DC magnetron sputtering with a sintered ceramic target of IZTO (In2O3 70 wt.%, ZnO 15 wt.%, SnO2 15 wt.%) and ITO (In2O3 90 wt.%, SnO2 10 wt.%). We investigated the structural, electrical, and optical properties of IZTO and ITO films. The structural and electrical properties of both films are sensitive on the substrate temperature. As the substrate temperature is increased, the electrical resistivity of ITO films is improved, but that of IZTO film increase over than $100^{\circ}C$. All IZTO and ITO thin films have good optical properties, which showed an average of transmittance over 80%. As a result, IZTO films can be a possible material for flexible display due to the low processing temperature.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.178.1-178.1
• /
• 2013

산화물 반도체는 가시광선영역인 380~780nm에서의 투과율이 80% 이상이고, 3.2eV 이상의 밴드갭과 높은 이동도를 가지는 물질로 투명하고 휘어지는 디스플레이에 전도유망한 물질로 연구되고 있다. $10cm^2/V{\cdot}s$ 이상의 이동도를 확보하기 위해 IGZO에서 Ga대신 Sn을 첨가한 ITZO 산화물 반도체에 대한 연구가 되고 있다. 본 연구에서 ITZO 산화물 반도체 박막 증착 시 가장 중요한 특성으로 알려진 산소의 영향에 따른 광학적 특성을 알아보기 위한 실험이다. RF 마그네트론 스퍼터링을 이용하여 산소 가스 분압에 따라 ITZO 박막을 증착하였다. $(Ar+O_2)$의 합을 20으로 고정하고 $O_2/(Ar+O_2)$의 비율을 0~40%까지 가변하였고, $O_2$의 비율이 증가함에 따라 증착율은 감소하는 경향을 보였다. 투명 소자로서의 가능성을 판단하기 위하여 밴드갭과 투과도를 측정하였다. 광학적 밴드갭은 증착 시 산소 분압이 0%에서 40%로 증가할수록 3.46eV에서 3.32eV로 감소하였고, 또한 투과도가 가시광 영역(380~770nm)에서 87%에서 85% 감소하였다. In, Sn, Zn 의 금속 원자와의 결합 과정에서 산소의 빈자리가 줄어들어 전도도가 감소하여 광학적 밴드갭이 감소함에 따라 투과도가 감소하는 것을 확인하였다.

• Korean Journal of Materials Research
• /
• v.33 no.5
• /
• pp.195-204
• /
• 2023

Micro-electronic gas sensor devices were developed for the detection of carbon monoxide (CO), nitrogen oxides (NO_x), ammonia (NH₃), and formaldehyde (HCHO), as well as binary mixed-gas systems. Four gas sensing materials for different target gases, Pd-SnO₂ for CO, In₂O₃ for NO_x, Ru-WO₃ for NH₃, and SnO₂-ZnO for HCHO, were synthesized using a sol-gel method, and sensor devices were then fabricated using a micro sensor platform. The gas sensing behavior and sensor response to the gas mixture were examined for six mixed gas systems using the experimental data in MEMS gas sensor arrays in sole gases and their mixtures. The gas sensing behavior with the mixed gas system suggests that specific adsorption and selective activation of the adsorption sites might occur in gas mixtures, and allow selectivity for the adsorption of a particular gas. The careful pattern recognition of sensing data obtained by the sensor array made it possible to distinguish a gas species from a gas mixture and to measure its concentration.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.346.2-346.2
• /
• 2014

To use the GaN based light-emitting diodes (LEDs) as solid state lighting sources, the improvement of light extraction and internal quantum efficiency is essential factors for high brightness LEDs. In this study, we suggested the new materials system of a zinc tin oxide (ZTO) layer formed on blue LED epi-structures to improve the light extraction. ZTO is a representative n-type oxide material consisted of ZnO and SnO system. Moreover, ZTO is one of the promising oxide semiconductor material. Even though ZTO has higher chemical stability than IGZO owing to its SnO2 content this has high mobility and high reliability. After formation of ZTO layer on p-GaN layer by using the spin coating method, structural and optical properties are investigated. The x-ray diffraction (XRD) measurement results show the successful formation of ZTO. The photoluminescence (PL) and absorption spectrum shows that it has 3.6-4.1eV band gap. Finally, the light extraction properties of ZTO/LED chip using electroluminescence (EL) measurement were investigated. The experimental and theoretical analyses were simultaneously conducted.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.3
• /
• pp.578-584
• /
• 2017

$SiO_2$ buffer layer (100 nm) has been deposited on PET substrate by electron beam evaporation. And then, IZTO (In-Zn-Sn-O) thin film has been deposited on $SiO_2$/PET substrate with different RF power of 30 to 60 W, working pressure, 1 to 7 mTorr, by RF magnetron sputtering. Structural, electrical and optical properties of IZTO thin film have been analyzed with various RF powers and working pressures. IZTO thin film deposited on the process condition of 50 W and 3 mTorr exhibited the best characteristics, where figure of merit was $4.53{\times}10^{-3}{\Omega}^{-1}$, resistivity, $4.42{\times}10^{-4}{\Omega}-cm$, sheet resistance, $27.63{\Omega}/sq.$, average transmittance (400-800 nm), 81.24%. As a result of AFM, all the IZTO thin film has no defects such as pinhole and crack, and RMS surface roughness was 1.147 nm. Due to these characteristics, IZTO thin film deposited on $SiO_2$/PET structure was found to be a very compatible material that can be applied to the next generation flexible display device.

• Korean Journal of Materials Research
• /
• v.23 no.6
• /
• pp.304-308
• /
• 2013

The effect of a sputter deposition sequence of Cu, Zn, and Sn metal layers on the properties of $Cu_2ZnSnS_4$ (CZTS) was systematically studied for solar cell applications. The set of Cu/Sn/Zn/Cu multi metal films was deposited on a Mo/$SiO_2$/Si wafer using dc sputtering. CZTS films were prepared through a sulfurization process of the Cu/Sn/Zn/Cu metal layers at $500^{\circ}C$ in a $H_2S$ gas environment. $H_2S$ (0.1%) gas of 200 standard cubic centimeters per minute was supplied in the cold-wall sulfurization reactor. The metal film prepared by one-cycle deposition of Cu(360 nm)/Sn(400 nm)/Zn(400 nm)/Cu(440 nm) had a relatively rough surface due to a well-developed columnar structure growth. A dense and smooth metal surface was achieved for two- or three-cycle deposition of Cu/Sn/Zn/Cu, in which each metal layer thickness was decreased to 200 nm. Moreover, the three-cycle deposition sample showed the best CZTS kesterite structures after 5 hr sulfurization treatment. The two- and three-cycle Cu/Sn/Zn/Cu samples showed high-efficient photoluminescence (PL) spectra after a 3 hr sulfurization treatment, wheres the one-cycle sample yielded poor PL efficiency. The PL spectra of the three-cycle sample showed a broad peak in the range of 700-1000 nm, peaked at 870 nm (1.425 eV). This result is in good agreement with the reported bandgap energy of CZTS.

• Resources Recycling
• /
• v.30 no.1
• /
• pp.66-76
• /
• 2021

Electric arc furnace dust (EAFD) contains compounds, such as oxides and chlorides, including large quantities of Zn, Pb and Fe. An efficient and stable method for the extraction of metal elements from EAFD is the Rotary Kiln Process. This method is used to recover Zn in the form of crude ZnO (approximately 60%) via the addition of a reducing agent (coke, anthracite) and limestone (for basicity control) to EAFD. This process is commonly used in industry as well as in research and development. Currently, this method is used in many Korean commercial plants, producing approximately 150,000 tons of Crude ZnO per year. The majority of Zn is found in crude ZnO (approximately 76%). In addition components such as Pb, Cd, Sn, In, Fe, Cl, and F are present as oxides, chlorides, and alkaline compounds. This elements have an adverse effect on the zinc smelting process. Therefore, a refining process that eliminates these impurities is essential. In this study, we developed a process technology that efficiently separates Zn and Pb from byproducts (mainly chlorides). A bag filter was used to collect Zn and Pb generated during the dry purification process of crude ZnO. Pure components were recovered as metals or metal carbonate.