• Journal of the Korean Chemical Society
• /
• v.19 no.3
• /
• pp.186-192
• /
• 1975

In the course of anthracite briquet combustion, air draft is usually controlled to continue burning of definite amount of briquet in the conventional hollow clay cylinder with air inlet hole open for given time, so that a large amount of CO tends to be produced. Therefore, it is necessary to establish an improved combustion process to depress the yielding rate of CO and for this purpose, we performed a basic experiment in which combustion rate of CO was measured in the mixture of $N_2, O_2 $and CO gas with or without the presence charcoal at the various temperature. The observed results showed that the burning temperature of CO is about 680${\sim}700^{\circ}C$, further burning rate of it was increased with increasing the amount of draft. From these facts, longer combustion time and low CO generation are thus contradictory to each other and it has been long desired to make those two compatible somehow. The purpose of the present investigation lies in designing an effective new briquet stove to meet the above requirements. The essential feature of the new briquet stove consisted in the use of two hollow iron cylinders with different inside diameter. A cylindrical air jacket thus formed served as a path through which small amount of secondary air run from the bottom of the stove to the upper vent holes. Heat exchange occurred between the upgoing secondary air and the burning briquet, which lowered the combustion temperature of the briquet. The results observed were selfevident as anticipated. It was confirmed that the combustion time was increased tolerably due to the heat loss from the combustion zone and that CO in the flue gas was reoxidized at the upper portion of the stove by the upgoing hot secondary air. By this reoxidation reaction the concentration of CO in the flue gas was found to be about 1/20 of that in case the conventional clay cylinder was used as briquet jacket.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.16 no.3
• /
• pp.27-34
• /
• 1987

The present paper was attempted to obtain the basic date concerning a reasonable preparing method and optimum fermentation conditions of Kochujang (Red pepper paste). To establish the standard quality of Kochujang, the chemical compositions and the volatile components of Kochujang was discussed. The native Kochujang collected from 80 households contained 40.51% of moisture, 6.00% of salts, 3.25 % of crude fat, 10.30 % of crude ash, pH 4.79, 9.28ml of tillable acidity. 19.60% of reducing sugar, 179.51 mg/100g of amino nitrogen and 4.43% of total nitrogen. The volatiles of Kochujang were extracted by a steam-distillation under the reduced pressure and determined by gas chromatography-mass spectrometry (GC-MS). Total volatile components identified in the native Kochujang were 46 components, i. e., 30 components in neutral fraction, 8 components in phenolic fraction and 8 components in acidic fraction, respectively. But no components were detected basic fraction.

• Journal of the Korean Geographical Society
• /
• v.51 no.6
• /
• pp.893-914
• /
• 2016

This paper describes the development of an inquiry-based fieldwork program based on Yangdong village where students explore the ways that it can develop in a sustainable way. Important considerations in an inquiry-based fieldwork design include what the key inquiry questions should be, the geographical issues of fieldwork location, the potential roles of mobile technologies, design of learning activities and a final product, and the roles of a teacher. Student fieldwork activities, including mapping land-use changes at the building level, detecting what should be changed or remain the same, and conducting interview with residents to examine their perceptions of overall tourism impacts, are supported by mobile technologies (i.e., the Collector for ArcGIS and the Google Forms). Twenty one high school students participated in a field test of the program in February 2016, which allowed authors to evaluate the program. Students' pre-, in-, and post-fieldwork activities were observed and the data and final products which they gathered and producted were analyzed. The post-program survey indicated that the students deepened and expanded their understanding of Yangdong village and expressed their satisfaction with the program in general. Incorporating mobile technologies into inquiry-based geographical fieldwork can help students involved in collaborative problem solving and creative activities in real world settings and create a shareable multimodal product combining maps, photo, and text.

• Korean Journal of Child Education & Care
• /
• v.18 no.1
• /
• pp.77-102
• /
• 2018

The objectives of this study were to analyze the longitudinal mediation effects of maternal parenting stress and psychosocial development of infant on the influence of paternal involvement during infancy to children's peer interactions. For these objectives, latent growth modeling was used and adapted to the data taken from the Panel Study on Korean Children(PSKC), Wave I (0-year olds) to Wave III (2-year olds) and Wave V(4-year olds) to Wave VII(6-year olds). During a total of six years, 1,018 parent responded. The major results of this study were as follows. First, maternal parenting stress(initial status) had a significant mediating effect on the influence of paternal involvement(initial status) to children's play interaction(initial status). Second, maternal parenting stress(initial status/change rate) had a longitudinal mediating eff ect on the influence of paternal involvements(initial status/change rate) to children's play disruption-disconnection interactions(initial status/change rate). Third, psychosocial development of infants(initial status/change rate) had a longitudinal mediating effect on the influence of paternal involvement(initial status/change rate) to children's play interactions(initial status/change rate). Fourth, psychosocial development of infant(initial status) had a significant mediating effect on the influence of paternal involvement(initial status) to children's play disruption-disconnection interactions(initial status). The implications of the findings of the current study and suggestions for future research were also discussed.

• Structural Engineering and Mechanics
• /
• v.31 no.2
• /
• pp.181-210
• /
• 2009

This paper presents the theoretical developments of an exact finite strip for the buckling and initial post-buckling analyses of isotropic flat plates. The so-called exact finite strip is assumed to be simply supported out-of-plane at the loaded ends. The strip is developed based on the concept that it is effectively a plate. The present method, which is designated by the name Full-analytical Finite Strip Method in this paper, provides an efficient and extremely accurate buckling solution. In the development process, the Von-Karman's equilibrium equation is solved exactly to obtain the buckling loads and the corresponding form of out-of-plane buckling deflection modes. The investigation of thin flat plate buckling behavior is then extended to an initial post-buckling study with the assumption that the deflected form immediately after the buckling is the same as that obtained for the buckling. It is noted that in the present method, only one of the calculated out-of-plane buckling deflection modes, corresponding to the lowest buckling load, i.e., the first mode is used for the initial post-buckling study. Thus, the postbuckling study is effectively a single-term analysis, which is attempted by utilizing the so-called semi-energy method. In this method, the Von-Karman's compatibility equation governing the behavior of isotropic flat plates is used together with a consideration of the total strain energy of the plate. Through the solution of the compatibility equation, the in-plane displacement functions which are themselves related to the Airy stress function are developed in terms of the unknown coefficient in the assumed out-of-plane deflection function. These in-plane and out-of-plane deflected functions are then substituted in the total strain energy expressions and the theorem of minimum total potential energy is applied to solve for the unknown coefficient. The developed method is subsequently applied to analyze the initial postbuckling behavior of some representative thin flat plates for which the results are also obtained through the application of a semi-analytical finite strip method. Through the comparison of the results and the appropriate discussion, the knowledge of the level of capability of the developed method is significantly promoted.

• KEPCO Journal on Electric Power and Energy
• /
• v.2 no.1
• /
• pp.97-101
• /
• 2016

ZnO has nanostructured material because of unique properties suitable for various applications. Amongst all chemical and physics methods of synthesis of ZnO nanostructure, the hydrothermal method is attractive for its simplicity and environment friendly condition. Nanostructure ZnO thin films have been successfully synthesized on fluorine doped tin oxide (FTO) substrate using hydrothermal method. A possible growth mechanism of the various nanostructures ZnO is discussed in schematics. The prepared materials were characterized by standard analytical techniques, i.e., X-ray diffraction (XRD) and Field-emission scanning electron microscopy (SEM). The XRD study showed that the obtained ZnO nanostructure thin films are in crystalline nature with hexagonal wurtzite phase. The SEM image shows substrate surface covered with nanostructure ZnO nanrod. The UV-vis absorption spectrum of the synthesized nanostructure ZnO shows a strong excitonic absorption band at 365 nm which indicate formation nanostructure ZnO thin film. Photoluminescence spectra illustrated two emission peaks, with the first one at 424 nm due to the band edge emission of ZnO and the second broad peak centered around 500 nm possibly due to oxygen vacancies in nanostructure ZnO. The Raman measurements peaks observed at $325cm^{-1}$, $418cm^{-1}$, $518cm^{-1}$ and $584cm^{-1}$ indicated that nanostrusture ZnO thin film is high crystalline quality. We trust that nanostructure ZnO material can be effectively will be used as a highly active and stable phtocatalysis application.

• Proceedings of the Korea Inteligent Information System Society Conference
• /
• 2005.05a
• /
• pp.190-197
• /
• 2005

본 논문에서는 출입국자 관리의 효율성과 체계적인 출입국 관리를 위하여 여권 코드를 자동으로 인식하고 위조 여권을 판별할 수 있는 여권 인식 및 얼굴 인증 방법을 제안한다. 여권 이미지는 기울어진 상태로 스캔되어 획득되어질 수도 있으므로 기울기 보정은 문자 분할 및 인식, 얼굴 인증에 있어 매우 중요하다. 따라서 본 논문에서는 여권 영상을 스미어링한 후, 추출된 문자열 중에서 가장 긴 문자열을 선택하고 이 문자열의 좌측과 우측 부분의 두께 중심을 연결하는 직선과 수평선과의 기울기를 이용하여 여권 여상에 대한 각도 보정을 수행한다. 여권 코드 추출은 소벨 연산자와 수평 스미어링, 8방향 윤곽선 추적 알고리즘을 적용하여 여권 코드의 문자열 영역을 추출하고, 추출된 여권 코드 문자열 영역에 대해 반복 이지화 방법을 적용하여 코드의 문자열 영역을 이진화한다. 이진화된 문자열 영역에 대해 CDM 마스크를 적용하여 문자열의 코드들을 복원하고 8방향 윤곽선 추적 알고리즘을 적용하여 개별 코드를 추출한다. 추출된 개별 코드는 ART2 알고리즘을 적용하여 인식한다. 얼굴 인증을 위해 템플릿 매칭 알고리즘을 이용하여 얼굴 템플릿 데이터베이스를 구축하고 여권에서 추출된 얼굴 영역과의 유사도 측정을 통하여 여권 얼굴 영역의 위조 여부를 판별한다. 얼굴 인증을 위해서 Hue, YIQ-I, YCbCr-Cb 특징들의 유사도를 종합적으로 분석하여 얼굴 인증에 적용한다. 제안된 여권 인식 및 얼굴 인증 방법의 성능을 평가를 위하여 원본 여권에 얼굴 부분을 위조한 여권과 노이즈, 대비 증가 및 감소, 밝기 증가 및 감소 및 여권 영상을 흐리게 하여 실험한 결과, 제안된 방법이 여권 코드 인식 및 얼굴 인증에 있어서 우수한 성능이 있음을 확인하였다.권 영상에서 획득되어진 얼굴 영상의 특징벡터와 데이터베이스에 있는 얼굴 영상의 특징벡터와의 거리 값을 계산하여 사진 위조 여부를 판별한다. 제안된 여권 인식 및 얼굴 인증 방법의 성능을 평가를 위하여 원본 여권에서 얼굴 부분을 위조한 여권과 기울어진 여권 영상을 대상으로 실험한 결과, 제안된 방법이 여권의 코드 인식 및 얼굴 인증에 있어서 우수한 성능이 있음을 확인하였다.진행하고 있다.태도와 유아의 창의성간에는 상관이 없는 것으로 나타났고, 일반 유아의 아버지 양육태도와 유아의 창의성간의 상관에서는 아버지 양육태도의 성취-비성취 요인에서와 창의성제목의 추상성요인에서 상관이 있는 것으로 나타났다. 따라서 창의성이 높은 아동의 아버지의 양육태도는 일반 유아의 아버지와 보다 더 애정적이며 자율성이 높지만 창의성이 높은 아동의 집단내에서 창의성에 특별한 영향을 더 미치는 아버지의 양육방식은 발견되지 않았다. 반면 일반 유아의 경우 아버지의 성취지향성이 낮을 때 자녀의 창의성을 향상시킬 수 있는 것으로 나타났다. 이상에서 자녀의 창의성을 향상시키는 중요한 양육차원은 애정성이나 비성취지향성으로 나타나고 있어 정서적인 측면의 지원인 것으로 밝혀졌다.징에서 나타나는 AD-SR맥락의 반성적 탐구가 자주 나타났다. 반성적 탐구 척도 두 그룹을 비교 했을 때 CON 상호작용의 특징이 낮게 나타나는 N그룹이 양적으로 그리고 내용적으로 더 의미 있는 반성적 탐구를 했다용을 지원하는 홈페이지를 만들어 자료 제공 사이트에 대한 메타 자료를 데이터베이스화했으며 이를 통해 학생들이 원하는 실시간 자료를 검색하여 찾을 수 있고 홈페이지를 방분했을 때 이해하기 어려운 그래프나 각 홈페이지가 제공하는 자료들에 대한 처리 방법을 도움말로 제공받을 수 있게 했다. 실

• Annual Conference of KIPS
• /
• 2001.10a
• /
• pp.297-300
• /
• 2001

최근의 컴퓨팅 환경은 이질적인 클라이언트와 서버들간의 상호 운용성을 요구하는 분산 어플리케이션을 위한 프로그래밍 파라다임을 지원하기 위한 분산 객체 컴퓨팅 환경으로 발전되고 있다. 여기에는 복잡한 네트워킹과 다양한 멀티미디어 응용 서비스를 위한 객체지향 기술들이 접목되고 있다. 이러한 분산 컴퓨팅 환경에서 처리되는 어플리케이션들의 실시간 서비스 지원을 위해 요구되는 실시간 특성과 분산 객체들의 관리의 어려움을 해결하기 위하여 본 논문에서는 실시간 객체그룹 플랫폼을 구축한다. 기존의 연구들은 실시간 CORBA를 사용하거나 또는 ORB를 수정하거나 실시간 운영체제상에 특정 CORBA 제품군을 사용하여 분산 환경의 특정 영역의 성능향상만을 도모하고 있다. 그러므로, 본 논문은 ORB의 수정 없이 표준 CORBA상에서 실시간 특성을 지원한 수 있는 실시간 객체그룹 플랫폼을 설계한다. 본 논문의 실시간 객체그룹 구조는 객체들의 관리적인 측면과 실시간 어플리케이션 서비스 지원 측면에 대한 요구사항들을 분석하여 정립한 모델이며, 구성요소들의 기능을 관리와 서비스로 분리하여 각각의 기능수행시에 발생하는 객체간의 상호작용이 다른 기능에 영향을 미치지 않도록 한다. 또한, 구축된 플랫폼은 실시간 어플리케이션 개발자에게 실시간 특성 파라미터의 표현과 처리에 대한 투명성을 부여하여 어플리케이션에 유연성과 확장성을 제공하기가 용이하도록 한다. 따라서, 본 논문은 실시간 객체그룹 플랫폼의 구성요소들에 대한 역할을 정의하고 기능을 정립하며, 각 구성요소들을 설계하고 구현하였으며, 구현되어진 실시간 객체그룹 플랫폼의 기능과 수행 성능을 검증한다.가지 유기화합물 중에서는 35.6%를 차지하였다. BTEX 각각 개별물질은 미국 환경보호청이 제시하는 일일 노출 기준량(Reference Concentration; RfC) 보다는 현저히 낮았다. 총 휘발성 유기화합물읜 농도는 실내가 실외 보다 높았다(I/O ratio 2.5). BTEX의 상대적 함량도 실내가 실외보다 높아 실내에도 발생원이 있음을 암시하고 있다. 자료 분석결과 유치원 실내의 벤젠은 실외로부터 유입되고 있었고, 톨루엔, 에틸벤젠, 크실렌은 실외뿐 아니라 실내에서도 발생하고 있었다. 정량한 8개 화합물 각각과 총 휘발성 유기화합물의 스피어만 상관계수는 벤젠을 제외하고는 모두 유의하였다. 이중 톨루엔과 크실렌은 총 휘발성 유기화합물과 좋은 상관성 (톨루엔 0.76, 크실렌, 0.87)을 나타내었다. 이 연구는 톨루엔과 크실렌이 총 휘발성 유기화합물의 좋은 지표를 사용될 있고, 톨루엔, 에틸벤젠, 크실렌 등 많은 휘발성 유기화합물의 발생원은 실외뿐 아니라 실내에도 있음을 나타내고 있다.>10)의 $[^{18}F]F_2$를 얻었다. 결론: $^{18}O(p,n)^{18}F$ 핵반응을 이용하여 친전자성 방사성동위원소 $[^{18}F]F_2$를 생산하였다. 표적 챔버는 알루미늄으로 제작하였으며 본 연구에서 연구된 $[^{18}F]F_2$가스는 친핵성 치환반응으로 방사성동위원소를 도입하기 어려운 다양한 방사성의 약품개발에 유용하게 이용될 수 있을 것이다.었으나 움직임 보정 후 영상을 이용하여 비교한 경우, 결합능 변화가 선조체 영역에서 국한되어 나타

• Korean Journal of Animal Reproduction
• /
• v.26 no.2
• /
• pp.87-94
• /
• 2002

This study was performed during the four seasons for the production of transgenic pigs containing the Cellulase Digest Gene. Purebred Landrace gilts and sows approximately 8∼15 months of age (n=126) were used for the collection of 1-cell zygotes for DNA microinjection and transfer. Retrospectively, estrus synchronization and superovulation schemes were evaluated to assess practicality fur zygote collection. Synchronization and superovulation procedures were used that cyclic gilts were synchronized with 20mg altrenogest (ALT) per day for 9 days after PG600 administration followed by superovulation with 1000 IU pregnant mares serum gonadotropin (PMSG) and 750IU human chorionic gonadotrophin (hCG). The cellulase digestion gene for microinjection is rat elasterase promoter (rEl) linked to CelD gene. After hormone treatment, 1,422 embryos were collected from 91 donors and 95.6% (1,359/1,422) embryos were in 1-cell stage which can be visualized the pronuclei for DNA microinjection. A total of 725 DNA microinjected embryos transferred into 35 recipients and produced 65 piglets from 13 litters. Pregnancy rate according to the number of transferred embryos to recipients was higher the group which received 21 to 24 embryos (50.0%) than other groups 20.0% in less and 33.3% in more. A tail tissue was collected from 65 piglets for biopsy. PCR screening was performed on each DNA sample using two separate sets of primers specific for the 5'- and 3'-flanking region of the rEl-CelD gene. Five of the 65 piglets (7.69%) were positive for the transgene. This study provide useful information regarding production of transgenic pig for bioreactor research.

• Applied Biological Chemistry
• /
• v.9
• /
• pp.125-147
• /
• 1968

This experiment was carried out as a part of the studies on reasonable application of nitrogen in rice plant to determine: (I) Nitrogen absorption. and rooting of rice seedlings as affected by urea foliar application at late seedling stage (II) Effect of leaf prunning and foliar application of urea at late heading stage on the maturation and yield of rice (III) Effect of foliar application of urea and its time during the stage of ear formation on yield of rice plant. Results obtained are summarized as follows. Exp.I: Nitrogen absorption and rooting of rice seedlings as affected be urea foliar application at late seedling stage. 1 : The foliar application of urea plots$(T_{1},T_2)$ snowed mare N-content than non-urea foliar application plot(T0) at lane seedling stage, being significant among treatments and foliar application of urea seemed more effective in increasing the N-content of seedlings. and promoted root settlement and early growth alter the transplanting. 2 : The carbon contents of the plants of $T_1$, and $T_2$ at late seedling stage increased than T0, and the carbon contents. of $T_1$ and $T_2$ plots became higher in amount in proportion to the nitrogen absorption as compared with those of $T_0$. 3 : C/N ratio appeared significant among soil application plots($N_1, \;N_2$) and foliar application of urea plots ($T_1$, $T_2$ and $T_0$). C/N ratio was lower in case of increased amount of nitrogen. The higher contents of nitrogen and carbon and lower C/N ratio resulted in the increment of root numbers and root lengths. Exp.II: Effect of leaf prunning and foliar application of urea at late heading stage on the maturation and yield of rice. 1 : There was a highly significant decrease in the maturing rate by severe leaf prunning. In the mean time, significant increase in maturing rate was observed with urea foliar application and it was found the more frequent application the more effective for higher maturing rate with a moderate significance. A correlationship between the level of prunning and maturing rate was enumerated to 0.961 of correlation coefficient, which indicated an increased maturing rate by the increased number of remaining leaves. 2 : The 1.000 grain weight, grain weight and hulled rice yield increased by leaf prunning in order (plot a$A_1$, $A_3$, $A_2$ and $A_0$ were 89.8%, 89.4%, 87.8% and 87.5% respectively, showing the highest of rate in $A_1$ and $A_3$ in methods of ear fertilization and being highly significant between its treatment. 3 : 1000 grain weights were highly significant between time of application, showing a tendency of increase of weights with the time lagging until days before earings as that of maturing rates. High significance was recognized between methods of ear fertilization, showing the highest in $A_2$ 23.18 gr. 4 : Yields per $3.3m^2$ were not significant between time of ear fertilization, whereas were highly significant between methods of ear fertilization. Those of $A_1$, $A_3$, $A_2$ and $A_0$ were 1.486 kg, 1.491 kg, 1.381 kg and 1.328 kg, respectively, showing the highest in $A_1$ and $A_3$. 5 : Hulling ratios showed significant different between time of ear fertilization, showing the highest in $T_2$, whereas those of methods of ear fertilization were highly significant between its treatment, Those of $A_1$, $A_3$, $A_2$ and $A_0$ were 84.72%, 84.06%, 83.29%, and 82.56% respectively, showing the highest m $A_2$ and $A_3$ among others. 6 : Yields of hulled rice per $3.3m^2$ showed significant different between time of ear fertilization, showing the highest in $T_1$ 1.192 kg. Whereas, those were highly significant between methods of ear fertilization. Those of $A_1$, $A_3$, $A_2$ and $A_0$ were 1.259 kg, 1.254 kg, 1.149 kg and 1.095 kg, respectively, showing the highest in $A_1$ and $A_2$. 7 : Contents of nitrogen on rice plant increased in case of nitrogen application as ear fertilizer and showed that the case of urea foliar application was more effective than that of soil application, showing the increased nitrogen content of rice plant was accompanied by carbon content.