• Korean Journal of Optics and Photonics
• /
• v.20 no.5
• /
• pp.276-280
• /
• 2009

A Cr:YAG crystal was used as a saturable absorber for passive Q-switching of a Nd:$YVO_4$ laser which was pumped by a 1-W continuous wave laser diode. The first surface of the Cr:YAG was high-reflection coated for the pump wavelength. The high-reflection coating improved the absorption efficiency of the pump beam in the Nd:$YVO_4$ through double pass absorption. It also prevented pump beam induced partial bleaching of the Cr:YAG. The peak-to-peak pulse fluctuation of passively Q-switched laser output was approximately 4 %. The minimum pulse-width was measured to be 7.11 ns. Also, the average pulse repetition rate was 9 kHz and the maximum output power was 16.27 mW.

• Journal of the Optical Society of Korea
• /
• v.19 no.1
• /
• pp.7-12
• /
• 2015

Up to ${\sim}520{\mu}J$ broadband mid-infrared (IR) supercontinuum (SC) generation in telecommunication multimode fiber (MMF) directly pumped by a $2.054{\mu}m$ nanosecond Q-switched Tm, $Ho:YVO_4$ laser is demonstrated. An average output power of 3.64 W is obtained in the band of ~1900 to ~2600 nm, and the corresponding optic-to-optic conversion efficiency is 67% by considering the coupling efficiency. The spectrum has extremely high flatness with negligible intensity variation (<2%) in the wavelength interval of ~2070 to ~2475 nm. The SC long-wavelength edge is limited by the silicon glass material loss, and by optimizing the MMF length, the SC spectrum could extend out to ${\sim}2.6{\mu}m$. The output SC pulse shapes are measured at different output powers, and no splits are found. The SC laser beam is nearly diffraction limited with an $M^2=1.15$ in $2.1{\mu}m$ measured by the traveling knife-edge method, and the laser beam spot is monitored by an infrared vidicon camera.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1368-1371
• /
• 2007

Laser-ablated ITO patterns showed the formation of shoulders at the edge of the ITO lines and a ripple-like structure of the etched bottom. When the laser ablation was applied in the fabrication of PDP panel, the laser-ablated ITO patterns showed a higher sustaining voltage than that of chemically wet-etched ITO.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.11
• /
• pp.8-12
• /
• 2008

For the reduction of fabrication cost and process time of AC plasma display panel (PDP), indium tin oxide (ITO) layer was patterned as bus electrode using Nd:$YVO_4$ laser. In comparison with the chemically wet etched ITO patterns, laser ablated ITO patterns showed the formation of shoulders and ripple-like structures at the edge of the ITO lines. For the reduction of shoulders and ripple-like structures, pulse repetition rate and scan velocity of laser was changed. In addition, we analyzed a discharge characteristic of PDP test panel to observe how the shoulders and ripple-like structures influence on the PDP. Based on experimental results, the pattern etched at the 500 mm/s and 40 kHz was better than any other condition. From this experiment we could see the possibility of the laser direct patterning for the application to the patterning of ITO in AC-PDP.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.11
• /
• pp.1765-1771
• /
• 2010

In the case of micro.electro-mechanical system (MEMS) devices, the quality of punched via hole is one of the most important factors governing the performance of the device. The common features that affect the laser micromachining of via holes drilled by using Nd:$YVO_4$ laser are described, and efficient optimization methods to measure them are presented. The analysis methods involving an orthogonal array, analysis of variance (ANOVA), and response surface optimization are employed to determine the main effects and to determine the optimal laser process parameters. The significant laser process parameters were identified and their effects on the quality of via holes were studied. Finally, an experiment in which the optimal levels of the laser process parameters were used was carried out to demonstrate the effectiveness of the optimization method.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2007.06a
• /
• pp.94-98
• /
• 2007

AC PDP에 사용되는 ITO 전극의 공정시간을 단축시키고 생산성을 향상시키기 위해서 $Nd:YVO_4$ laser(${\lambda}=1064\;nm$)를 사용하여 ITO 전극 패턴을 형성하였다. ITO etchant를 사용하여 ITO 전극 패턴을 형성한 샘플과 비교해서 laser를 사용하여 제작한 샘플은 ITO 라인 가장자리에 shoulder와 물결무늬를 형성했다. Q스위치 $Nd:YVO_4$ laser와 갈바노메트릭 스캐닝 시스템을 사용하여 500 mm/s의 스캔속도와 40 kHz의 펄스 반복 율을 기본조건으로 결정했다. PDP 테스트 샘플을 제작하여 방전 테스트를 진행하였다. 사진식각공정을 이용하여 만든 PDP 샘플과 비교해서 laser를 이용하여 제작한 PDP 샘플의 최소 방전유지전압은 더 높게 측정됐다. 이것은 ITO 라인의 shoulder와 물결무늬의 형성과 관련이 있다고 판단된다. 본 실험을 통해 레이저를 이용한 PDP용 ITO 전극막의 직접 패터닝 가능성을 확인할 수 있었다.

• Journal of the Optical Society of Korea
• /
• v.12 no.4
• /
• pp.298-302
• /
• 2008

We have developed a 270-W 15-kHz MOPA system based on side-pumped rod-type Nd:YAG gain modules. The master oscillator is a 3-W 15-kHz $TEM_{00}$ $Nd:YVO_4$ laser with a pulse duration of 30 ns. To preserve the high beam quality during the amplification, we use image relay and polarization rotation which can simultaneously compensate for thermal lensing and thermal birefringence generated in the rod-type gain modules. After the amplification to 270 W with six rod-type gain modules, the beam quality factor ($M^2$) of the amplified laser beam is 5-10, and the pulse duration is maintained at 30 ns.

• Journal of Photoscience
• /
• v.10 no.2
• /
• pp.203-208
• /
• 2003

Two coupled molecules were successfully synthesized by condensation of amine-donor-substituted barbituric acid derivativies as nonlinear optical chromophores. A flexible spacer of the alkyl chain with different lengths of carbon chains (5 and 6 carbons) was introduced between two chromophores, which prevented crystallization and aggregation of molecules. Two coupled molecules (B-Cn-B, n=5, 6) had glass-transition temperatures on a second heating around 81 and 76$^{\circ}C$ without melting points, respectively. To explore the linear optical properties, thin-films were prepared and examined by a photometry method using Nd:YVO$_4$ CW laser. Also, microscopic and macroscopic nonlinear optical properties were measured by Hyper-Rayleigh Scattering (HRS) and the Maker Fringes method using Nd:YAG ps pulse laser, respectively. In spite of the moderate hyperpolarizabilities of coupled molecules, the second order NLO coefficient (d$\_$33/) was larger than the conventional Disperse Red 1 doped PMMA polymeric system.

• Journal of Powder Materials
• /
• v.26 no.6
• /
• pp.463-470
• /
• 2019

Fe₃O₄/SiO₂/YVO₄:Eu³⁺ multifunctional nanoparticles are successfully synthesized by facile stepwise sol-gel processes. The multifunctional nanoparticles show a spherical shape with narrow size distribution (approximately 40 nm) and the phosphor shells are well crystallized. The Eu³⁺ shows strong photoluminescence (red emission at 619 nm, absorbance at 290 nm) due to an effective energy transfer from the vanadate group to Eu. Core-shell structured multifunctional nanoparticles have superparamagnetic properties at 300 K. Furthermore, the core-shell nanoparticles have a quick response time for the external magnetic field. These results suggest that the photoluminescence and magnetic properties could be easily tuned by either varying the number of coating processes or changing the phosphor elements. The nanoparticles may have potential applications for appropriate fields such as laser systems, optical amplifiers, security systems, and drug delivery materials.