• 한국임상수의학회지
• /
• 제32권4호
• /
• pp.374-379
• /
• 2015

A 10-year-old gelding Warmblood weighing 560 kg was referred to J&C Equine Hospital with the history of hyperpnea, depression, pawing, and rolling for 7 hours. According to the results of clinical and ultrasound examination, it was considered that intestines were distended with thickened wall. The horse had been treated with lactated Ringers' solution (14 L, IV), flunixin meglumine (1.1 mg/kg, IV), and mineral oil (1 L, PO), but he did not show any responses to those treatments. Exploratory laparotomy was performed and identified incarcerated small intestine through the epiploic foramen. The horse received resection and anastomosis of the entrapped small intestine. After surgery, the horse was treated with intensive postoperative care of fluid therapy (5 L with 20 mEq/L KCl, every 2 hours), flunixin meglumine (1.1 mg/kg, IV, sid), antibiotics (penicillin 22,000 IU/kg, IV, qid and gentamicin 6.6 mg/kg, IV, sid), lidocaine constant rate infusion (bolus 1.3 mg/kg over 15 minutes then 0.05 mg/kg/minute), common nutritional supplements, nasogastric intubation every 2 hours and trunk bandage. Postoperative feeding program had started with small amount of hay every 4 hours and gradually increased to normal amount till 5 days. At 77 days after surgery, he showed sudden outbreak of colic and was euthanized. The causes of colic were small intestinal strangulation by passing through the mesenteric rents and postoperative adhesion between small intestines. According to the results, it is recommended to perform perioperative intensive care of horse with colic and to use several methods to prevent adhesions during abdominal surgery of horses.

• 한국재료학회지
• /
• 제16권12호
• /
• pp.731-738
• /
• 2006

It is seriously considered using Al CMP (chemical mechanical planarization) process for the next generation 45 nm Al wiring process. Al CMP is known that it has a possibility of reducing process time and steps comparing with conventional RIE (reactive ion etching) method. Also, it is more cost effective than Cu CMP and better electrical conductivity than W via process. In this study, we investigated 4 different kinds of slurries based on abrasives for reducing scratches which contributed to make defects in Al CMP. The abrasives used in this experiment were alumina, fumed silica, alkaline colloidal silica, and acidic colloidal silica. Al CMP process was conducted as functions of abrasive contents, $H_3PO_4$ contents and pressures to find out the optimized parameters and conditions. Al removal rates were slowed over 2 wt% of slurry contents in all types of slurries. The removal rates of alumina and fumed silica slurries were increased by phosphoric acid but acidic colloidal slurry was slightly increased at 2 vol% and soon decreased. The excessive addition of phosphoric acid affected the particle size distributions and increased scratches. Polishing pressure increased not only the removal rate but also the surface scratches. Acidic colloidal silica slurry showed the highest removal rate and the lowest roughness values among the 4 different slurry types.

• 한국환경과학회지
• /
• 제16권10호
• /
• pp.1203-1208
• /
• 2007

Feathers are produced in huge quantities as a waste product at commercial poultry processing plants. Since feathers are almost pure keratin protein, feather wastes represent an alternative to more expensive dietary ingredients for animal feedstuffs. Generally they become feather meal used as animal feed after undergoing physical and chemical treatments. These processes require significant energy and also cause environmental pollutions. Therefore, biodegradation of feather by microorganisms represents an alternative method to prevent environment contamination. The aim of this study was to investigate cultural conditions affecting keratinolytic protease production by Bacillus pumilus RS7. We also assessed the nutritive value of microbial and alkaline feather hydrolysates, The composition of optimal medium for the keratinolytic protease was fructose 0.05%, yeast extract 0.3%, NaCl 0.05%, K2HPO4 0.03%, KH2PO4 0.04% and MgCl2 6H2O 0.01%, respectively. The optimal temperature and initial pH was $30^{\circ}C$ and 9.0, respectively. The keratinolytic protease production under optimal condition reached a maximum after 18 h of cultivation. Total amino acid content of feather hydrolysates treated by NaOH and B. pumilius RS7 was $113.8\;{\mu}g/ml$ and $504.9\;{\mu}g/ml$, respectively. Essential amino acid content of feather hydrolysates treated by NaOH and B. pumilius RS7 was $47.2\;{\mu}g/ml$ and $334.0\;{\mu}g/ml$, respectively. Thus, feather hydrolysates have the potential for utilization as an ingredient in animal feed.

• 한국약용작물학회지
• /
• 제11권2호
• /
• pp.161-166
• /
• 2003

순계 분리된 인삼의 우수 계통으로부터 염류내성 계통을 선발하기 위하여 배배양으로부터 유기된 인삼 개체를 염류 종류와 농도별 차이에 따라 엽병의 생장율과 생존율을 조사한 결과 N, P, K 그리고 Na와 Fe의 복합처리구에서는 10배 이상의 농도로 첨가된 처리구 모두에서 엽병의 생장과 개체의 생존율이 전혀 이뤄지지 않는 것으로 나타났으나 K 처리구에서만 다수의 생존개체를 확인할 수 있었다. 또한 Ca 10배 처리구와 Mg 20배 처리구까지는 비교적 엽병의 생장과 개체의 생존이 유지되는 것으로 나타났다. 7가지 염류 모두를 복합처리한 결과에서도 1.25와 2.5배 처리구에서만 약간의 생장을 보였을 뿐 5배 이상 처리한 고농도에서는 생장과 생존을 모두 불가능한 것으로 나타나 인삼의 염류내성 계통을 선발하기 위한 종합염류 농도는 2.5배 수준으로 처리하는 것이 적절하리라 사료된다.

• 한국재료학회지
• /
• 제13권2호
• /
• pp.115-119
• /
• 2003

The thick film type sensor having Pt/Na Super Ionic Conductor(NASICON) solid electrolyte/Pt/$Na_2$$SO_4$/Pt catalyst system for $SO_2$gas was fabricated by screen-print method. The phase of Na Super Ionic Conductor solid electrolyte sintered at different temperature of 1050, 1150,$ 1250^{\circ}C$ and for different time of 1.5, 2.5, 3.5 hr were investigated by XRD. The Electromotive Force variation of the sensor with $SO_2$concentrations and operating temperatures were investigated. The major phase of Na Super Ionic Conductor film sintered at 115$0^{\circ}C$ for 3.5 hr was sodium zirconium silicon phosphate($Na_3$Zr$_2$$Si_2$PO$_{12}$). The Nernst's slope of Na Super Ionic Conductor sensor for $SO_2$gas with the variation of concentration from 10 to 100 ppm was 167.14 ㎷/decade at the operating temperature of $500 ^{\circ}C$. The increase of oxygen partial pressure was not affected to the variation of Nernst's slope.e.

• 분석과학
• /
• 제5권1호
• /
• pp.143-152
• /
• 1992

본 연구는 니켈기 초내열 합금 KM 1557의 내식성 및 고온 산화 성질을 조사하기 위하여 황산, 염산, 질산, 인산 및 초산에서의 부식시험과 $900^{\circ}C$, $950^{\circ}C$, $1050^{\circ}C$에서의 고온산화시험, 그리고 $900^{\circ}C$에서 75% $Na_2SO_4-25%$ NaCl 염욕에서 고온황화 침지시험을 실시하였다. 각 시험 후 시편의 단면을 광학현미경으로 관찰하였으며, EPMA 및 X-ray mapping으로 분석하여 시편의 조성분포를 조사하였다. 각종 산에서의 내식성 및 염욕에서의 고온 내식성은 우수하였으며 고온산화시험 결과 산화물의 양은 내부 및 입계간 산화물인 $Al_2O_3$층의 깊이에 주로 영향을 받는 것으로 나타났다.

• 생약학회지
• /
• 제37권4호
• /
• pp.278-282
• /
• 2006

In this study, we analyzed and quantified the contents of magnolol (1), honokiol (2), and obovatol (3) in the leaves of Magnolia species by HPLC. HPLC methods were developed and validated by ICH guide lines comparing the linearity, intraday precision, inter-day precision. The optimal conditions were as follows; wavelength: 288 nm, column: Zorbax Eclipse XDBC18 $(2.1\times150\;mm,\;5{\mu}m)$, mobile phase: Acetonitril - 0.1 % $H_3PO_4$ (45:55, v/v) buffer, flow rate: 0.5 ml/min. The contents of magnolol, honokiol and obovatol were 1.08%, 2.37%, and 0.57% in the leaves of M. officinalis, 0.50%, 0.03%, and 1.54% in the leaves of M. biloba, 0.37%, 0.03%, and 0.76% in the leaves of M. obovata. The contents of effective ingredients in the leaves of M. officinalis and M biloba were higher than that of M. obovata. Especially, the content of obovatol in the leaves of M. biloba was remarkably high. This result showed that the shapes of leaves have a certain relationship with the content of obovatol.

• 한국물환경학회지
• /
• 제28권4호
• /
• pp.551-560
• /
• 2012

The objectives of this study were to elucidate spatio-temporal heterogeneity of water chemistry and develop empirical models using trophic variables in Daechung Reservoir during 2005-2010 along with in situ tests of nutrient enrichment bioassays (NEB). The relations of water quality parameters in regard to precipitation showed that seasonal and interannual fluctuations of biological oxygen demand (BOD), total nitrogen (TN) and pH were minor, whereas conductivity, suspended solids (SS), and total phosphorus (TP) were largely varied in response to the magnitude of rainfall. The CHL maxima occurred immediately after the spate of TP during the high flow, indicating that phytoplankton growth was directly controlled by phosphorus. Empirical linear models of CHL-TP indicated that the variation of CHL in premonsoon was accounted 60% ($R^2$ = 0.60, p < 0.05, n = 54) by TP. In the mean time, empirical models of annual CHL-TN showed that the variation of CHL was weakly accounted ($R^2$ = 0.16, p < 0.001) by TN and more strongly ($R^2$ = 0.44, p < 0.001) by TP. Thus, the variation of CHL was more explained by the variation of TP than TN. In situ tests of Nutrient Enrichment Bioassays (NEBs) showed that the growth of CHL was greater in the P-treatments (as $PO_4-P$) than the control and N-treatment (as $NO_3-P$). Overall, our results suggest that phosphorus was aprimary limiting nutrient controlling the seasonal phytoplankton growth, based on the in situ experiments of NEBs.

• 한국식품영양학회지
• /
• 제23권4호
• /
• pp.556-561
• /
• 2010

Tomato fruits(Lycoperisicon esculentum) synthesize the glycoalkaloids dehydrotomatine and ${\alpha}$-tomatine, possibly as defense against bacteria, fungi and insects. We developed a new effective method to prepare and purify dehydrotomatine and ${\alpha}$-tomatine that exists in tomato fruits using alumina column chromatography and high performance liquid chromatography (HPLC). The tomato glycoalkaloids(TGA) in tomato was extracted with 2% acetic acid, and then precipitated with ammonium hydroxide(pH=10.5). The dry precipitate substance was applied on alumina column, and then fractionated with water saturated n-butylalcohol. The TGA(Fr. No. 26~36) were collected and dried under reduced pressure. The TGA was performed on a reverse phase HPLC(Inertsil ODS-2, $5\;{\mu}m$), eluted with acetonitrile/20mM $KH_2PO_4$(24:76, v/v) at 208 nm. Two peaks were detected on HPLC, and individual peak was collected by repeating HPLC. Furthermore, to confirm the identity dehydrotomatine and ${\alpha}$-tomatine, each peak isolated was hydrolyzed with 1N HCl into sugar and aglycone tomatidine. The sugars were converted to trimethylsilyl ester derivatives. The nature and molar ratios of sugars were identified by gas-liquid chromatography(GLC) and the aglycone by high-performance liquid chromatography(HPLC). The first peak (Rt=17.5 min) eluted from HPLC was identified as dehydrotomatine, and second peak(Rt=21.0 min) was as ${\alpha}$-tomatine. This technique has been used effectively to prepare and isolate dehydrotomatine and ${\alpha}$-tomatine from tomato fruits.

• 대한치과보철학회지
• /
• 제30권1호
• /
• pp.73-83
• /
• 1992

Now composite resin restoration is clinically accepted in the repair of fractured PFM case, many mechanical surface treatment methods are performed to increase retentive force. The main purpose of this study was to compare the retentive force among the possible surface treatments and to insure the best method for the clinical application to the fractures porecelain and the exposed metal surface. To compare and to analyze the retentive force of repair resin, porcelain specimen were divided into 2 groups, etching group and non-etching group, and etching group were treated with 37% $H_3PO_4$, 1.23% APF, 10% HF and non-etching groups were treated with diamond bur, micro-sandblasasting. Also, metal specimens were divided by 2 groups : one was non-precious metal group which was treated with diamond bur, micro-sandblasting and tin plating and electrolytic etching, the other was precious metal group which was composed of micro-sandblasting treatment only and tin plating treatment with micro-sandblasting. Each specimen had been restored for 48 hours and the bond strength of each specimen was calculated with Universal testing machine. The results were as follows : 1. Porcelain specimen had higher bonding strength than metal specimen for the repair resin(P<0.01). 2. In porcelain specimen, 10% HF etching group had the highest bonding strength among etching and non-etching group. 3. Metal specimen treated with micro-sandblasting had highest bonding strength among the non-sandblasting had hightest bonding strength among the non-precious group, tin plating group had higher bonding strength than micro-sandblasting group between the precious metal groups. 4. Bonding strength of tin plating was increased in precious metal group only.