• Environmental Engineering Research
• /
• v.17 no.4
• /
• pp.217-225
• /
• 2012

In this study, the treatability of two target contaminants during the Fenton reaction, n-hexadecane and 1-methylnaphthalene, was evaluated as a function of the amounts of $FeCl_2$ and $H_2O_2$ injected into open and closed reaction systems. In the Fenton reaction of n-hexadecane and 1-methylnaphthalene, the mass recovery of the target contaminants was above 95% in the closed system. However, when the Fenton reaction was performed with high amounts of $H_2O_2$ and $FeCl_2$ injected in the open system, a reduction of approximately 40% of the initial mass of 1-methylnaphthalene was observed. This trend may be explained by the unique physical properties of 1-methylnaphthalene, which has higher volatility than n-hexadecane. Further, this trend was well correlated with the rise in high temperature at the initial reaction stage. Considering the mass recovery of the two target contaminants, the reaction temperature, and the residual concentration of $H_2O_2$ at different amounts of $FeCl_2$ and $H_2O_2$ injected, it can be suggested that the Fenton reaction should be performed with controlled conditions that can provide a suitable reaction environment between oxidant and contaminants.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.7
• /
• pp.600-604
• /
• 2005

We studied that structural and optical properties of ZnO films depend on oxygen contents. ZnO films were deposited on Si (111) substrates at room temperature by rf sputtering system and the thickness of films was 100 nm. The ZnO films were annealed in thermal furnace for 2 h at 800 and $900^{\circ}C$ in $H_2O,\;N_2$, and air ambient gases to control oxygen contents. We used AES, PL, XRD, AFM. As our result, crystal quality and luminescence improved until O/Zn is 1. However, when O/Zn ratio Is larger than 1, the structural and optical properties were getting worse.

• Journal of Korean Society for Atmospheric Environment
• /
• v.13 no.1
• /
• pp.91-98
• /
• 1997

Y-zeolite and ${\gamma}$-Al$_2$O$_3$ were used as supports on CO and $C_3$H$_{6}$ oxidation for diesel emission control. The catalysts composed of Pd and Pt as active components were wash coated on honeycomb type ceramic substrate. The oxidation of CO and $C_3$H$_{6}$ was carried out over prepared honeycomb in a fixed bed continuous reactor in the temperature range of 20$0^{\circ}C$~50$0^{\circ}C$ and 20,000 GHSV (h$^{-1}$ ). Surface area of Y-zeolite was larger than that of ${\gamma}$-Al$_2$O$_3$ due to channel structure of Y-zeolite. Therefore, high conversion of CO and $C_3$H$_{6}$ could be obtained because of good dispersion of active metals over Y-zeolite. The honeycomb used Y-zeolite as a support showed higher $C_3$H$_{6}$ conversion than that of ${\gamma}$-Al$_2$O$_3$ due to better cracking and isomerization activity of Y-zeolite. PdPt catalyst showed high conversion of CO and $C_3$H$_{6}$ at low temperature region, 20$0^{\circ}C$~30$0^{\circ}C$, for their synergy effects. PdPt/Y-Zeolite catalyst could achieve more than 80％ conversion of $C_3$H$_{6}$ at 30$0^{\circ}C$. The use of Y-zeolite as a support increased CO and $C_3$H$_{6}$ conversion, and decreased SO$_2$ conversion very effectively. Y-zeolite found to have a good adaptability as a support for the diesel emission after treatment system.

• Journal of Hydrogen and New Energy
• /
• v.21 no.4
• /
• pp.278-285
• /
• 2010

The Sulfur-Iodine (SI) thermochemical hydrogen production process of a closed cycle consists of three sections, which are so called the Bunsen reaction section, the $H_2SO_4$ decomposition section and the HI decomposition section. To identify the role of oxygen that can be supplied to the Bunsen reaction section via the $H_2SO_4$ decomposition section, Bunsen reactions with a $SO_2,\;SO_2-O_2$ mixture and $SO_2-N_2$ mixture as feed gases were carried out using a stirred reactor in the presence of $I_2/H_2O$ mixture. As the results, the amounts of $I_2$ unreacted under the feed of mixture gases were higher than those under the feed of $SO_2$ gas only, and the amount of HI produced was relatively decreased. The results of Bunsen reaction using $SO_2-O_2$ mixture were similar to those using $SO_2-N_2$ mixture. It may be concluded that an oxygen in $SO_2-O_2$ mixture has a role as a carrier gas like a nitrogen in $SO_2-N_2$ mixture. The effects of oxygen were decreased with increasing temperature and decreasing oxygen content in $SO_2-O_2$ mixture.

• Corrosion Science and Technology
• /
• v.5 no.6
• /
• pp.206-212
• /
• 2006

The effects of sub-ppm levels of $H_2S$ and the adsorbed water on the atmospheric corrosion of silver were studied with In situ weight balance to study the effect of the adsorbed water on the kinetic behavior and to determine the rate-controlling step, with XPS to analyze the tarnish film, and with calculation of phase equilibrium to predict the stable solid phase, the concentrations of dissolved species ($Ag^-$, $H^+$, $S^{2-}$, $HS^-$) and the equilibrium potentials ($E_{Ag^+/Ag}$, $E_{H^+/H_2}$, $E_{O_2/O^{2-}$). The results of weight measurements showed that oxygen was required for the sulfidation of silver in 100 ppb $H_2S$ and humidified environments enhanced the tarnished rate and oxidizing power. In addition, the rate determining step for tarnishing silver was shown to be changed to transport though the tarnish film.

• Applied Chemistry for Engineering
• /
• v.24 no.1
• /
• pp.67-71
• /
• 2013

$FeCl_3$ has been used as an etchant for metal etching such as Fe, Cu, and Al. In the process of metal etching, $Fe^{3+}$ is reducted to $Fe^{2+}$ and the etching rate becomes slow and etching efficiency decreased. Waste $FeCl_3$ etchant needs to be regenerated because of its toxicity and treatment cost. In this work, HCl was initially mixed with the waste $FeCl_3$ and then, strong oxidants, such as $O_2$ and $H_2O_2$, were added into the mixed solution to regenerate the waste etchant. During successive etching and regeneration processes, oxygen-reduction potential (ORP) was continuously measured and the relationship between ORP and etching capability was investigated. Regenerated etchant using a two vol% HCl of the total etchant volume and a very small amount of $H_2O_2$ was very effective in recovering etching capability. During the etching-regeneration process, the same oxygen-reduction potential variation cannot be repeated every cycle since concentrations of $Fe^{2+}$ and $Fe^{3+}$ ions were continuously changed. It suggested that the control of etching-regeneration process based on the etching time becomes more efficient than that of the process based on oxygen reduction potential changes.

• Journal of the Korean Ceramic Society
• /
• v.27 no.2
• /
• pp.274-282
• /
• 1990

SnO2 powder was prepared by hydroxide method and oxalate method. In hydroxide method, the pH dependence of powder characteristics was investigated by using buffer solution. As increasing the pH of solution, SnO2 powder size was decreased because nucleation rate was inctreased by more supersaturation of solution. Also, we found that the powder by our method has larger specific surface area in comaprison with other method. And the degree of agglomeration of precipitate with the change of precipitation temperature was investigated in oxalate method. The SnC2O4 was angular shape precipitate, and the size of the SnC2O4 was increased with the increase of precipitation temperature in methanol solvent.

• Journal of the Korean Ceramic Society
• /
• v.36 no.5
• /
• pp.465-470
• /
• 1999

Sensing properties of $\alpha$-Fe2O3 thin film to reducing gases such as CHx and CO were systematically examined after deposition on Al2O3 substrate by PECVD(Plasma Enhanced Chemical Vapor Deposition)technique. Microstructure of deposited $\alpha$-Fe2O3 thin film showed the porous island structure. This specimen was annealed at 450, 550, $650^{\circ}C$ to enhance the gas sensing properties and investigated in terms of CO and C4H10 concentration from 500ppm to 3,000 ppm at operating temperature of 35$0^{\circ}C$ The gas sensitivity(%) to C4H10 measured at the operating temperature of 35$0^{\circ}C$ was 98.24 (highest sensitivity) 69.51 to CO and 2% to CH4 respectviely.

• Journal of the Korean Ceramic Society
• /
• v.28 no.3
• /
• pp.225-233
• /
• 1991

In this study, we tried to find out the appropriate synthetic condition and magnetic properties of Ni-Zn ferrite {(NixZn1-x)Fe2O4} powders (where X=0, 0.1, 0.2, 0.3, ……0.9, 1). Ferrite powders were prepared by wet-direct method at 86℃ for 6hrs from FeCl36H2O, NiCl26H2O, and ZnCl2. The powders of (NixZn1-x)Fe2O4 (where X=0.4, 0.5, 0.6) have a good crystallinity, but the other ferrite powders consist of crystal and precursor ferrite. The ferrite powder's lattice constant is increased when ratio of ZnO contant is increased in the ferrite composition. And initial permeability was measured after sintering, result indicated regular pattern except (Ni0.4Zn0.6)Fe2O4 when the frequency were changed 10KHz to 10MHz.

• Journal of Industrial and Engineering Chemistry
• /
• v.67
• /
• pp.486-496
• /
• 2018

Bimetallic Pd@Ni nanostructure exhibited enhanced co-catalytic activity for the selective hydrogenation of benzaldehyde compare to their monometallic counterparts. Impregnation of these mono/bimetallic nanostructures on mesoporous $TiO_2$ leads to several surface modifications. The bimetallic PNT-3 ($Pd_3@Ni_1/mTiO_2$) exhibited large surface area ($212m^2g^{-1}$), and low recombination rate of the charge carriers ($e^--h^+$). The hydrogenation reaction was analyzed under controlled experiments. It was observed that under UV-light irradiations and saturated hydrogen atmosphere the bimetallic PNT-3 photocatalyst display higher rate constant $k=5.31{\times}10^{-1}h^{-1}$ owing to reduction in the barrier height which leads to efficiently transfer of electron at bimetallic/$mTiO_2$ interface.