• Tuberculosis and Respiratory Diseases
• /
• v.52 no.3
• /
• pp.251-259
• /
• 2002

Background : Reduced lung compliance and increased lung resistance are the primary lung mechanical abnormalities in acute respiratory distress syndrome (ARDS). Although there is little information regarding the mechanisms responsible for the increases in the respiratory resistance of ARDS, bronchodilators have been frequently administered in mechanically ventilated ARDS patients. To determine the effect of a bronchodilator on the respiratory mechanics depending on the level of applied positive end-expiratory pressure (PEEP), the changes in the respiratory mechanics by salbutamol inhalation was measured under the variable PEEP level in patients with ARDS. Materials and Methods : Fifteen mechanically ventilated paralyzed ARDS patients (14 of male, mean age 57 years) were enrolled in this study. The respiratory system compliance, and the maximum and minimum inspiratory resistance were obtained by the end-inspiratory occlusion method during constant flow inflation using the CP-100 pulmonary monitor (Bicore, Irvine, CA, USA). The measurements were performed at randomly applied 8, 10 and 12 cm $H_2O$ PEEP before and 30 mins after administrating salbutamol using a meter-dose-inhaler (100ug${\times}$6). Results : 1) The maximum inspiratory resistance of the lung was higher than the reported normal values due to an increase in the minimal inspiratory resistance & additional resistance. 2) The maximum inspiratory resistance and peak airway pressure were significantly higher at 12cm $H_2O$ of PEEP compared with those at 10cm $H_2O$ of PEEP. 3) Salbutamol induced a significant decrease in the maximum and the minimum inspiratory resistance but no significant change in the additional resistance only was observed at 12cm $H_2O$ of PEEP(from $15.66{\pm}1.99$ to $13.54{\pm}2.41$, from $10.24{\pm}2.98$ to $8.04{\pm}2.34$, and from $5.42{\pm}3.41$ to $5.50{\pm}3.58cm$ $H_2O$/L/sec, respectively). 4)The lung compliance did not change at the applied PEEP and salbutamol inhalation levels. Conclusion : The bronchodilator response would be different depending on the level of applied PEEP despite the increased respiratory resistance in patients with ARDS.

• Journal of the Korean Applied Science and Technology
• /
• v.28 no.3
• /
• pp.321-328
• /
• 2011

The autothermal reforming reaction of methane was investigated to produce hyd rogen with Ni/$CeO_2-ZrO_2$, Ni/$Al_2O_3$-MgO and Ni-Ru/$Al_2O_3$-MgO catalysts. Honeycomb metalli c monolith was applied in order to obtain high catalytic activity and stability in autothermal r eforming. The catalysts were characterized by XRD, BET and SEM. The influence of various catalysts on hydrogen production was studied for the feed ratio($O_2/CH_4$, $H_2O/CH_4$). The $O_2/CH_4$ and $H_2O/CH_4$ ratio governed the methane conversion and temperature profile of reactor. Th e reactor temperature increased as the reaction shifted from endothermic to exothermic reactio n with increasing $O_2/CH_4$ ratio. Among the catalysts used in the experiment, the Ni-Ru/$Al_2O_3$-MgO catalyst showed the highest activity. The 60% of $CH_4$ conversion was obtained, and th e reactor temperature was maintained $600^{\circ}C$ at the condition of GHSV=$10000h^{-1}$ and feed ratio S/C/O=0.5/1/0.5.

• Korean Journal of Materials Research
• /
• v.9 no.4
• /
• pp.414-418
• /
• 1999

Typical metal oxide thin films having optical and electrical properties are widely used as inorganic functional materials. Liquid phase deposition(LPD) method, a new low temperature process, has been developed for the several advantages of no vacuum system, low cost, high throughput, and low processing temperature(<$50^{\circ}C$). Silica powder was added to 40wt% hydrofluoro-silicic acid($H_2$SiF\ulcorner) to obtain an immersing solution of silica-saturated hydrofluorosilicic acid solution. Boric acid solution was continuously added in the range from 0 to 0.05M to prepare supersaturated hydrofluorosilicic acid solution. LPD $SiL_2$film was formed with the variation of added amount of $H_2$O. The SiO$_2$thin film could be prepared from hydrofluorosilicic acid by LPD method. The thickness of LPD $_SiO2$film was influenced by the boric acid concentration and added amount of $H_2$O. Silicon in thin film existed as SiF\ulcorner by Raman spectrum.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.6
• /
• pp.1675-1680
• /
• 2014

A peroxopolyoxotungsten-based ionic hybrid was synthesized by anion-change of peroxopolyoxometalate (POM) $PW_4O{_{24}}^{3-}$ with dicationic long-chain alkyl imidazolium ionic liquids. The characterization was conducted by FT-IR, TGA, $^1H$-NMR and CHN Elemental analyses. Its catalytic performance was evaluated by the epoxidation of soybean oil with $H_2O_2$ under solvent-free condition, including testing of organic cations influence, catalytic reusability and reaction conditions. The catalyst was proved to be a highly efficient recyclable catalyst for epoxidation of various vegetable oils with $H_2O_2$, showing high $H_2O_2$ utilization efficiency, high catalytic activity, convenient recovery and good reuse ability.

• Korean Journal of Microbiology
• /
• v.33 no.3
• /
• pp.187-192
• /
• 1997

The strain producing biosurfactant was isolated from soil. The isolated strain was identified as the genus Tsukamurella through its morphological, cultural, physiological, menaquinone type, fatty acid composition characteristics. The highest biosurfactant production by Tsukamurella sp. 26A was observed after 4 days cultivation in the culture medium containing n-hexadecane 7%, $NaNO_{3}$ 0.2%, $K_2HPO_4$ 0.001%, $MgSO_{4}$ center dot $7H_{2}O$ 0.02%, $CaCl_2$ center dot $2H_{2}O$ 0.02%, yeast extract 0.02%(pH 6.8-7.0, 30^{\circ}C.$ The surface and interfacial tension of an aqueous solution reached 30 mNim and 1.5 mNim, respectively. The biosurfactant stabilized oil-in-water emulsion with a variety of hydrocarbons, edible oils and petroleum oils.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2003.11a
• /
• pp.161-164
• /
• 2003

본 연구에서는 수열합성법으로 $SrAl_2O_4:Eu$ 형광체 분말을 합성하여 이들의 발광 특성과 장잔광 특성 등에 대해서 고찰하였다. 증류수에 $Sr(NO_3)_2,\;Al(NO_3)_3{\cdot}9H_2O,\;Eu(NO_3)_3{\cdot}6H_2O$ 등의 금속염을 용해시킨 용액을 $NH_4OH$ 수용액으로 pH를 적당히 조절하고 고온 고압의 Autoclave 반응용기 내에서 반응시켰다. 이렇게 합성된 분말은 균일한 입도 분포를 나타내었으면, sub-micron 크기의 초미세 분말이었다. 합성된 $SrAl_2O_4:Eu$ 초미세 분말을 $Ar-H_2$ 가스 환원분위기에서 $1100-1400^{\circ}C$ 온도로 2시간동안 열처리시켜서 형광 특성을 나타내도록 만들었다. 분말의 여기 및 발광 특성을 측정한 길과, 발광파장을 520 nm로 고정시켜 측정한 여기스펙트럼은 $250\~450nm$의 넓은 파장영역에 걸쳐 여기가 일어났고, 발광스펙트럼은 520 nm에서 최대 피크를 나타내었다. 또한 10분간 여기 시킨 후 520 nm 파장에 대한 잔광 특성이 1000분 이상 지속되는 우수한 장잔광 특성을 나타내었다.

• Journal of the Korean Wood Science and Technology
• /
• v.41 no.6
• /
• pp.566-575
• /
• 2013

The fruits of Taxus cuspidata were collected, divided into seeds and fruits, and extracted with 95% EtOH. The extracts were evaporated under the reduced vacuum pressure, concentrated, then successively fractionated with a series of n-hexane, dichloromethane, ethyl acetate and water on a separatory funnel to get some freeze dried samples. A portion of the EtOAc (arils:1.65 g, seeds:1.04 g) and $H_2O$ (arils:7 g, seeds:10 g) soluble samples were chromatographed on a Sephadex column using MeOH-$H_2O$ (1:1, 1:3, 1:5, v/v), EtOH-hexane (3:1, v/v) mixture and 100% $H_2O$ as eluting solvents to isolate pure compounds from the fractions. The isolates were developed by cellulose TLC using t-BuOH-HOAc-$H_2O$ (TBA; 3:1:1, v/v/v) and 6% aqueous HOAc. Visualization was done under ultraviolet light and by spraying the vanillin-HCl-EtOH reagent (4.8:12:480, v/v/v). followed by heating. The structures of the isolates were characterized by $^1H$- and $^{13}C$-NMR, DEPT, 2D-NMR, LC/MS and EI-MS spectra. In addition to the NMR and MS spectra, acid hydrolysis and permethylation were used to determine the correct structure of the isolated sugar compound. Their structures were elucidated as (+)-catechin (1), (-)-epicatechin (2), (+)-gallocatechin (3), (-)-epigallocatechin (4) and ${\beta}$-D-fructofuranose-($2{\rightarrow}4$)-O-${\beta}$-D-glucopyranose($1{\rightarrow}4$)-O-${\alpha}$-D-glucopyranose ($1{\rightarrow}2$)-O-${\beta}$-D-fructofuranose (5) on the basis of the above experimental evidences.

• Journal of Soil and Groundwater Environment
• /
• v.18 no.4
• /
• pp.50-57
• /
• 2013

For the last couple of decades, the Fenton (-like) systems have been extensively studied for oxidation of organic contaminants in water. Recently, zero-valent iron (ZVI) has received attention as a Fenton catalyst as well as a reducing agent capable of producing reactive oxidants from oxygen. In this study, the ZVI-based Fenton reaction was assessed for the oxidative degradation of phenol using $ZVI/O_2$, $ZVI/H_2O_2$, ZVI/Oxalate/$O_2$ and hv/ZVI/Oxalate/$O_2$ systems. Reaction parameters such as pH and reagent dose (e.g., ZVI, $H_2O_2$, and oxalate) were examined. In the presence of oxalate (ZVI/Oxalate/$O_2$ and hv/ZVI/Oxalate/$O_2$ systems), the degradation of phenol was greatly enhanced at neutral pH values. It was found that ZVI accelerates the Fenton reaction by reducing Fe(III) into Fe(II). The conversion of Fe(III) into Fe(II) by ZVI was more stimulated at acidic pH than at near-neutral pH values.

• Journal of Food Hygiene and Safety
• /
• v.13 no.4
• /
• pp.365-369
• /
• 1998

The in vitro effects of trisodium phosphate and cetylpyridinium chloride on E. coli 0157:H7 and L. monocytogenes were investigated. The trisodium phosphate and cetylpyridinium chloride was bactericidal toward E. coli 0157:H7 and L. monocytogenes. The killing effects of the $1{\times}10^{-2}\;M$ trisodium phosphate on E. coli 0157:H7 and L. monocytogenes were 30~40%, 40~50%, respectively. The killing effects of the $5{\times}10^{-7}\;M$ cetylpyridinium chloride on E. coli 0157:H7 and L. monocytogenes were 90~95%, 95~99%, respectively. The killing effects of the trisodium phosphate was $10^5$ times that of the cetylpyridinium chloride. Factors effecting the bactericidal action of trisodium phosphate and cetylpyridinium chloride were investigated and the action depended on temperature and pH.

• Journal of the Korean Chemical Society
• /
• v.38 no.4
• /
• pp.283-287
• /
• 1994

The crystal stucture of bithional surfoxide, $C_{12}H_6Cl_4O_3S$, has been determined from 2295 independent reflections collected on an automated CAD-4 diffractometer with a graphite-monochromated $Mo-K\alpha$ radiation. The crystal belongs to the monoclinic, space group P2$_1$/n, with a unit cell dimensions a = 12.448(4), b = 9.740(1), c = $11.815(2)\AA$, $\beta$ = $100.06^{\circ}$, $\mu$ = 9.02 cm$^{-1}$, Dm = 1.76 g/cm$^3$, Dc = 1.75 g/cm$^3$, F(000) = 744, and Z = 4. The structure was solved by the direct method and refined by the least-squares method. The final R values was 0.037 for 2295 independent reflections. Overall conformation of the molecule is folded with respect to central surfur atom. Comparing with the molecular conformation of bithional, one of phenyl rings was swinged with about $180^{\circ}.$ This conformational change in the molecule results in the existance of intramolecular-hydrogen bond of S-O(3)---H-O(1) type and its steric hindrance between this moiety and the other phenyl ring. The two best planes of the phenyl rings have a maximum deviation of 0.009 $\AA$ for C(1) atom. The dihedral angle between two phenyl rings is $99.22^{\circ}.$ In the crystal structure, the molecules are packed with intermolecular-hydrogen bond of O(3)---H-O(2).