• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 추계학술대회 논문집 학회본부
• /
• pp.305-307
• /
• 1996

Because most LIM is driven by inverter, input voltage is involved with the time harmonics. Therefore the equiLlQ/ent circuit for an inverter-fed LIM has to be modified to represent every harmonics present in supply voltage. This paper analyzes the characteristics and loss of LIM to construct the equivalent circuit for each time harmonics through the static test and theoretical analysis. To make an analysis of nonsinusoidal supply waveforms, it is developed the simulation program to calculate the RMS, peak value and THD for any waveforms expressing Fourier series.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 전력전자학술대회 논문집
• /
• pp.689-693
• /
• 2001

The conventional three-level high frequency phase-shifted dc/dc converter has a disadvantage that a circulating current flows through transformer and switching devices during the freewheeling interval. Due to this circulating current and RMS current stress, conduction losses of transformer and switching devices increases. To alleviate these problems, we propose an improved three-level Zero Voltage and Zero Current Switching (ZVZCS) dc/dc converter using a tapped inductor, a snubber capacitor and two snubber diodes attached at the secondary side of transformer. The proposed ZVZCS converter is verified on a 10 kW, 30kHz experimental prototype.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.330-333
• /
• 2005

The fabrication of mold fur nano imprint lithography (NIL) is experimentally reported using the scanning probe lithography (SPL) technique, instead of the conventional I-beam lithography technique. The nanometer scale patterning structure is fabricated by the localized generation of oxide patterning on the silicon (100) wafer surface with a thin oxide layer, The fabrication method is based on the contact mode of scanning probe microscope (SPM) in air, The precision cleaning process is also performed to reach the low roughness value of $R_{rms}=0.084 nm$, which is important to increase the reproducibility of patterning. The height and width of the oxide dot are generated to be 15.667 nm and 209.5 nm, respectively, by applying 17 V during 350 ms.

• Wind and Structures
• /
• 제16권2호
• /
• pp.179-192
• /
• 2013

The flow around two rectangular cylinders with aspect ratio of 0.5 in a tandem arrangement, was investigated using pressure measurements (in a wind tunnel) and flow visualizations (in a water tunnel) in the range of P/h from 0.6 to 4.0. Four flow patterns were identified, and processes of shear layers wrapping around, the shear layer reattachment, vortices wrapping around and vortices impingement, were observed. Mean and rms pressure distributions, flow visualizations and Strouhal numbers were presented and discussed. The paper revealed that the variations of Strouhal numbers were associated with the shear layers or vortex interference around two cylinders.

• Nuclear Engineering and Technology
• /
• 제41권9호
• /
• pp.1191-1204
• /
• 2009

In this study, a CFD methodology is employed to address the problem of the prediction of the flow in a T-junction. An Unsteady Reynolds Averaged Navier-Stokes (URANS) approach has been selected for its low computational cost. Moreover, Unsteady Reynolds Navier-Stokes methodologies do not need complex boundary formulations for the inlet and the outlet such as those required when using Large Eddy Simulation (LES) or Direct Numerical Simulation (DNS). The results are compared with experimental data and an LES calculation. In the past, URANS has been tried on T-junctions with mixed results. The biggest limit observed was the underestimation of the oscillatory behavior of the temperature. In the present work, we propose a comprehensive approach able to correctly reproduce the root mean square (RMS) of the temperature directly downstream of the T-junction for cases where buoyancy is not present.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1996년도 춘계학술발표회논문집(2)
• /
• pp.199-204
• /
• 1996

In the present the mean temperature and the temperature fluctuation of non-isothermal parallel liquid sodium jets were measured and analyzed changing the temperature difference and mean velocity of the hot and cold sodium. The sampling frequency and sampling time were 420Hz and three seconds, respectively. The wave-form characteristics were discussed in regard to the peak-to-peak amplitudes and the periods provided by a wave analysis. And also the correlations of the temperature fluctuation in rms value and the peak amplitude are derived. The overall mean accuracy ratios of the correlations are 1.07 and 1.08 with a standard deviation of 0.17 and 0.15, respectively.

• 한국진공학회지
• /
• 제4권S2호
• /
• pp.24-29
• /
• 1995

The magnetic amd magneto-optical(MO)properties of Co-based multilayered(ML)films are known to vary sensitively according to the manufacturing methods and the film microstructures. Co/Pd and Co/Pt ML films with ultrathin layers of Co were prepared by alternating deposition in an ultrahigh-vacuum physical-vapor-deposition system. The individual layer thicknesses of the samples were estimated making use of the angular positions of x-ray diffraction peaks. The magnetic and MO properties were investigated, and correlated systematically to the structural parameters of the films. A Kerr spectrometer was self-manufactured to measure the MO properties such as Kerr rotation angle, ellipticity and reflectivity. The rms surface roughness was also measured using atomic force microscopy. Some of the samples showed good properties for MO medium, such as large perpendicular magnetic anisotropy and Kerr rotation, and perfect squareness of the magnetic hysteresis loop.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 A
• /
• pp.388-391
• /
• 1996

The conventional high frequency phase-shifted full bridge DC-DC converter has a disadavantage that a circulating current flows through transformer and switching devices during the freewheeling interval Due to this circulating current, RMS current stress, conduction losses of transformer and switching devices are increased. To alleviate this problem, this study provides a novel circulating current free type high frequency soft switching phase-shifted full bridge DC-DC converter which applies the energy recovery snubber(ERS) attached at the secondary side of transformer. The ERS adopted in this study is consisted of three fast recovery diode($Ds_1$, $Ds_2$, $Ds_3$), two resonant capacitor($Cs_1$, $Cs_2$) and a small resonant inductor [(Lr) : It can be ignored because the transformer leakage inductance(Ll) is able to use in stead of inserting the resonant inductor(Lr)]

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.617-617
• /
• 2013

최근 그래핀 연구와 더불어 2차원 구조의 나노소재에 대한 관심이 급증하면서 육각형의 질화붕소(hexagonal boron nitride; h-BN) 박막(nanosheet) [1]이나 붕소 탄화질화물(boron caronitride; BCN) 박막 [2,3]과 같은 2차원 구조체에 대한 연구가 활발히 진행되고 있다. 그 중 BCN은 반금속(semimetal)인 흑연(graphite)과 절연체인 h-BN이 결합된 박막으로 원소의 구성 비율에 따라 전기적 특성을 제어할 수 있다는 장점이 있다. 따라서 다양한 나노소자로의 응용을 위한 연구가 활발히 진행되고 있다. 본 연구에서는 폴리스틸렌(polystyrene, PS)과 보레인 암모니아(borane ammonia)를 고체 소스로 이용하여 열화학기상증착법으로 BCN 박막을 SiO2 기판 위에 직접 합성하였다. SEM과 AFM 관측을 통해 합성된 BCN 박막의 두께가 약 10 nm이며, RMS roughness가 0.5~2.6 nm로 매우 낮은 것을 확인하였다. 합성과정에서 PS의 양을 조절하여 BCN 박막의 탄소의 밀도를 성공적으로 제어하였으며, 이에 따라 전기적인 특성이 제어되는 양상을 확인하였다. 또한 합성온도 변화에 따른 BCN 박막의 전기적인 특성이 제어되는 양상을 확인하였다. 추가적으로 같은 방법을 이용하여 BCN 박막을 Cu 위에서 합성하여 SiO2 기판위에 전사하였다. 합성된 BCN 박막의 구조적 특징과 화학적 조성 및 결합 상태를 투과전자현미경(transmission electron microscopy), X-선 광전자 분광법(X-ray photoelectron spectroscopy), 라만 분광법(Raman spectroscopy)을 통해 조사하였고, 이온성 용액법(ionic liquid) [4]을 이용하여 전계효과 특성을 측정하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 F
• /
• pp.2578-2580
• /
• 1999

In this paper, an embedded micro processor based resistance spot welding controller is introduced which has been recently developed by Hyosung Co. Ltd. The performance of rapid and constant high current control is tested experimentally. This paper shows configurations of measuring system for high current and realtime RMS conversion techniques of sampled discrete data. A digital proportional control is adopted for this system and the result shows that this new product is working well at wide range of welding current and the performance is improved compared with some other commercially available controllers that are widely used in our industries. User friendly MMI system and a computer network system to monitor each welding processes are also presented.