• 제목/요약/키워드: $Ga_{2}O_{3}$

검색결과 941건 처리시간 0.031초

Effects of Al-doping on IZO Thin Film for Transparent TFT

  • Bang, J.H.;Jung, J.H.;Song, P.K.
    • 한국진공학회:학술대회논문집
    • /
    • 한국진공학회 2011년도 제40회 동계학술대회 초록집
    • /
    • pp.207-207
    • /
    • 2011
  • Amorphous transparent oxide semiconductors (a-TOS) have been widely studied for many optoelectronic devices such as AM-OLED (active-matrix organic light emitting diodes). Recently, Nomura et al. demonstrated high performance amorphous IGZO (In-Ga-Zn-O) TFTs.1 Despite the amorphous structure, due to the conduction band minimum (CBM) that made of spherically extended s-orbitals of the constituent metals, an a-IGZO TFT shows high mobility.2,3 But IGZO films contain high cost rare metals. Therefore, we need to investigate the alternatives. Because Aluminum has a high bond enthalpy with oxygen atom and Alumina has a high lattice energy, we try to replace Gallium with Aluminum that is high reserve low cost material. In this study, we focused on the electrical properties of IZO:Al thin films as a channel layer of TFTs. IZO:Al were deposited on unheated non-alkali glass substrates (5 cm ${\times}$ 5 cm) by magnetron co-sputtering system with two cathodes equipped with IZO target and Al target, respectively. The sintered ceramic IZO disc (3 inch ${\phi}$, 5 mm t) and metal Al target (3 inch ${\phi}$, 5 mm t) are used for deposition. The O2 gas was used as the reactive gas to control carrier concentration and mobility. Deposition was carried out under various sputtering conditions to investigate the effect of sputtering process on the characteristics of IZO:Al thin films. Correlation between sputtering factors and electronic properties of the film will be discussed in detail.

  • PDF

고온 및 고온고습 환경 내에서 ZnO:Al 투명전극의 열화가 CIGS 박막형 태양전지의 성능 저하에 미치는 영향 (Effect of Degraded Al-doped ZnO Thin Films on Performance Deterioration of CIGS Solar Cell)

  • 김도완;이동원;이희수;김승태;박지홍;김용남
    • 한국세라믹학회지
    • /
    • 제48권4호
    • /
    • pp.328-333
    • /
    • 2011
  • The influence of Al-doped ZnO (AZO) thin films degraded under high temperature and damp heat on the performance deterioration of Cu(In,Ga)$Se_2$ (CIGS) solar cells was investigated. CIGS solar cells with AZO/CdS/CIGS/Mo structure were prepared on glass substrate and exposed to high temperature ($85^{\circ}C$) and damp heat ($85^{\circ}C$/85% RH) for 1000 h. As-prepared CIGS solar cells had 64.91% in fill factor (FF) and 12.04% in conversion efficiency. After exposed to high temperature, CIGS solar cell had 59.14% in FF and 9.78% in efficiency, while after exposed to damp heat, it had 54.00% in FF and 8.78% in efficiency. AZO thin films in the deteriorated CIGS solar cells showed increases in resistivity up to 3.1 times and 4.4 times compared to their initial resistivity after 1000 h of high temperature and damp heat exposure, respectively. These results can be explained by the decreases in carrier concentration and mobility due to diffusion or adsorption of oxygen and moisture in AZO thin films. It can be inferred that decreases in FF and conversion efficiency were caused by an increase in series resistance, which resulted from an increase in resistivity of AZO thin films degraded under high temperature and damp heat.

The developments of heavy hydrocarbon reformer for SOFC

  • 배중면
    • 한국재료학회:학술대회논문집
    • /
    • 한국재료학회 2012년도 춘계학술발표대회
    • /
    • pp.58.2-58.2
    • /
    • 2012
  • Heavy hydrocarbon reforming is a core technology for "Dirty energy smart". Heavy hydrocarbons are components of fossil fuels, biomass, coke oven gas and etc. Heavy hydrocarbon reforming converts the fuels into $H_2$-rich syngas. And then $H_2$-rich syngas is used for the production of electricity, synthetic fuels and petrochemicals. Energy can be used efficiently and obtained from various sources by using $H_2$-rich syngas from heavy hydrocarbon reforming. Especially, the key point of "Dirty energy smart" is using "dirty fuel" which is wasted in an inefficient way. New energy conversion laboratory of KAIST has been researched diesel reforming for solid oxide fuel cell (SOFC) as a part of "Dirty energy smart". Diesel is heavy hydrocarbon fuels which has higher carbon number than natural gas, kerosene and gasoline. Diesel reforming has difficulties due to the evaporation of fuels and coke formation. Nevertheless, diesel reforming technology is directly applied to "Dirty fuel" because diesel has the similar chemical properties with "Dirty fuel". On the other hand, SOFC has advantages on high efficiency and wasted heat recovery. Nippon oil Co. of Japan recently commercializes 700We class SOFC system using city gas. Considering the market situation, the development of diesel reformer has a great ripple effect. SOFC system can be applied to auxiliary power unit and distributed power generation. In addition, "Dirty energy smart" can be realized by applying diesel reforming technology to "Dirty fuel". As well as material developments, multidirectional approaches are required to reform heavy hydrocarbon fuels and use $H_2$-rich gas in SOFC. Gd doped ceria (CGO, $Ce_{1-x}Gd_xO_{2-y}$) has been researched for not only electrolyte materials but also catalysts supports. In addition, catalysts infiltrated electrode over porous $La_{0.8}Sr_{0.2}Ga_{0.8}Mg_{0.2}O_3-{\delta}$ and catalyst deposition at three phase boundary are being investigated to improve the performance of SOFC. On the other hand, nozzle for diesel atomization and post-reforming for light-hydrocarbons removal are examples of solving material problems in multidirectional approaches. Likewise, multidirectional approaches are necessary to realize "Dirty energy smart" like reforming "Dirty fuel" for SOFC.

  • PDF

비정질 InGaZnO4 박막의 전기적, 광학적 특성간의 상관관계 연구 (The Effect of Tail State on the Electrical and the Optical Properties in Amorphous IGZO)

  • 배성환;유일환;강석일;박찬
    • 한국세라믹학회지
    • /
    • 제47권4호
    • /
    • pp.329-332
    • /
    • 2010
  • In order to investigate the effect of tail state on the electrical and the optical properties in amorphous IGZO(a-IGZO), a-IGZO films were deposited at room temperature on fused silica substrats using pulsed laser deposition method. The laser pulse energy was used as the processing parameter. In-situ post annealing was carried out at $150^{\circ}C$ right after the film deposition. The $O_2$ partial pressure during the deposition and the post annealing was fixed to 10mTorr. The carrier mobility of the a-IGZO films had a range from 2 to $18\;cm^2/Vs$ at carrier concentrations greater than $10^{18}\;cm^{-3}$. As the laser energy density increased, the Hall mobility increased. And post annealing improved the Hall mobility, as well. The optical property was examined using the ultraviolet-visible spectroscopy. The a-IGZO films that have low Hall mobility exhibited stronger and broader absorption tails in >3.0 eV region. Post annealing reduced the intensity of the tail-like absorption. The absorption tail in a-IGZO films is an important factor which affects the electrical and the optical properties.

In Situ Spectroscopy in Condensed Matter Physics

  • Noh, Tae Won
    • 한국진공학회:학술대회논문집
    • /
    • 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
    • /
    • pp.92-92
    • /
    • 2014
  • Recently, many state-of-art spectroscopy techniques are used to unravel the mysteries of condensed matters. And numerous heterostructures have provided a new avenue to search for new emergent phenomena. Especially, near the interface, various forms of symmetry-breaking can appear, which induces many novel phenomena. Although these intriguing phenomena can be emerged at the interface, by using conventional measurement techniques, the experimental investigations have been limited due to the buried nature of interface. One of the ways to overcome this limitation is in situ investigation of the layer-by-layer evolution of the electronic structure with increasing of the thickness. Namely, with very thin layer, we can measure the electronic structure strongly affected by the interface effect, but with thick layer, the bulk property becomes strong. Angle-resolved photoemission spectroscopy (ARPES) is powerful tool to directly obtain electronic structure, and it is very surface sensitive. Thus, the layer-by-layer evolution of the electronic structure in oxide heterostructure can be investigated by using in situ ARPES. LaNiO3 (LNO) heterostructures have recently attracted much attention due to theoretical predictions for many intriguing quantum phenomena. The theories suggest that, by tuning external parameters such as misfit strain and dimensionality in LNO heterostructure, the latent orders, which is absent in bulk, including charge disproportionation, spin-density-wave order and Mott insulator, could be emerged in LNO heterostructure. Here, we performed in situ ARPES studies on LNO films with varying the misfit strain and thickness. (1) By using LaAlO3 (-1.3%), NdGaO3 (+0.3%), and SrTiO3 (+1.7%) substrates, we could obtain LNO films under compressive strain, nearly strain-free, and tensile strain, respectively. As strain state changes from compressive to tensile, the Ni eg bands are rearranged and cross the Fermi level, which induces a change of Fermi surface (FS) topology. Additionally, two different FS superstructures are observed depending on strain states, which are attributed to signatures of latent charge and spin orderings in LNO films. (2) We also deposited LNO ultrathin films under tensile strain with thickness between 1 and 10 unit-cells. We found that the Fermi surface nesting effect becomes strong in two-dimensions and significantly enhances spin-density-wave order. The further details are discussed more in presentation. This work was collaborated with Hyang Keun Yoo, Seung Ill Hyun, Eli Rotenberg, Ji Hoon Shim, Young Jun Chang and Hyeong-Do Kim.

  • PDF

MIRIS 냉각 설계 검증을 위한 열해석 연구

  • 이덕행;문봉곤;박영식;이대희;정웅섭;이창희;남욱원;박성준;표정현;차상목;가능현;박장현;선광일;이승우;박종오;이형목;;한원용
    • 한국우주과학회:학술대회논문집(한국우주과학회보)
    • /
    • 한국우주과학회 2011년도 한국우주과학회보 제20권1호
    • /
    • pp.23.2-23.2
    • /
    • 2011
  • 과학기술위성3호의 주탑재체 Multi-purpose Infra-Red Imaging System(MIRIS)는 한국천문연구원이 개발하고 있는 소형 적외선 우주망원경이다. MIRIS는 적외선 센서의 열잡음을 최소화시키기 위하여 망원경의 온도가 허용범위를 넘지 않도록 설계되었다. 특히 3K의 심우주를 향해 MIRIS의 복사열을 자연 방출하는 Passive cooling은 임무 성공에 영향을 미치는 매우 중요한 과정이다. 이를 검증하고자 NX 7.0(Space Systems Thermal, TMG 탑재)을 사용하여 열 해석을 수행하였다. 각 부품별로 물성과 열광학 특성을 적용하여 전도 및 복사를 통한 열전달 과정을 계산하였고, MIRIS의 궤도 특성을 고려하여 정상상태에서의 망원경 온도를 얻었다. 그 결과 Passive cooling을 통해 MIRIS 망원경이 허용범위 아래로 냉각되는 것을 확인하였다.

  • PDF

Ca($OH_2$)-$H_2 O$-$CO_2$계의 기액반응으로부터 비정질 탄산칼슘의 합성 및 결정화 (Synthesis and Crystallization of Amorphous Calcium Carbonate by Gas-Liquid Reaction of System Ca($OH_2 O$)-$H_2$-$CO_2$)

  • 임재석;김가연;임굉
    • 공학논문집
    • /
    • 제5권1호
    • /
    • pp.73-87
    • /
    • 2004
  • 수산화칼슘현탁액과 탄산가스를 출발물질로 15~$50^{\circ}C$의 온도에서 기액반응으로 비정질 탄산칼슘($CaCO_3$.$nH_2 O$)의 생성과정을 전기저도도의 연속측정법, X-선회절법 및 투과전자현미경법을 이용하여 조사한 결과, 반응초기생성물은 비정질 탄산칼슘으로 반응현탁액의 전기전도도는 비정질 탄산칼슘의 생성 중 크게 강하하고 있으며, 이것은 수산화칼슘의 입자표면이 비정질 탄산칼슘미립자로 뒤덮여 용해를 방해받는 것과 비정질 탄산칼슘이 용액 속에서 불안정하여 즉시 용해한 다음 석출하여 칼사이트로 전이되어 미세한 침강성 탄산칼슘이 나란히 결합한 연쇄형 칼사이트가 생성된다. 비정질 탄산칼슘이 연쇄형 칼사이트로 변화하는 동안 현탁액의 전기전도도는 급격히 회복되고 이 과정에서 고농도 수산화칼슘현탁액의 외관점도가 상승한다. 이것은 연쇄형 칼사이트의 뒤얽힘에 의한 것이며, 다시 전기전도도의 1회 회복단계 이후에는 미반응 수산화칼슘에 의하여 비정질 탄산칼슘이 생성이 소멸되어 칼사이트의 성장반응이 이루어지고 pH가 9.5이하에서 연쇄형 칼사이트는 결합부분이 먼저 용해하여 결정질 탄산칼슘으로 분리생성된다. 비정질 탄산칼슘의 생성 및 합성온도의 영역은 전기전도도법에서 $15^{\circ}C$일 때 1차 강하단계(a-단계)에서 가장 적합하다.

  • PDF

감초추출물의 지방세포와 조골세포에 대한 분화효과 (Effects of Glycyrrhiza inflata Batal Extracts on Adipocyte and Osteoblast Differentiation)

  • 서초롱;변종선;안재진;이재환;홍정우;장상호;박계원
    • 한국식품영양과학회지
    • /
    • 제42권7호
    • /
    • pp.1015-1021
    • /
    • 2013
  • 창과감초(Glycyrrhiza inflata Batal)는 한약재의 조화를 돕고 해독, 항염증, 항궤양 등의 약리작용으로 한방에서 널리 이용되는 약용식물이다. 본 연구에서는 지방세포와 조골세포에서 감초의 생리활성을 확인하고자 감초에탄올추출물(GBE)을 이용하여 세포분화 촉진여부를 조사하였다. GBE의 세포독성여부를 통해 안전하다고 확인된 $1{\sim}30{\mu}g/mL$의 농도 내에서 실험이 진행되었고 지방세포 분화조건에서 다분화능 세포 C3H10T1/2과 지방전구세포 3T3-L1의 Oil Red O 염색을 통해 GBE의 지방세포분화 촉진효과를 확인할 수 있었다. 또한 지방세포의 핵심전사조절인자인 $PPAR{\gamma}$와 그의 표지유전자 aP2, AdipoQ, $C/EBP{\alpha}$의 발현량 증가를 통해 GBE의 지방세포분화 촉진효과를 재확인하였다. 이와 일관된 결과로서 조골세포 분화조건에서 다분화능 세포 C3H10T1/2과 조골전구세포 MC3T3-E1의 ALP 염색을 통해 GBE의 조골세포분화 촉진효과를 확인하였고 조골세포 표지유전자인 ALP, RUNX2, osterix, collagen의 발현량 증가를 통해 GBE의 조골세포분화 촉진효과를 재확인하였다. 이에 따라 본 연구에서는 GBE의 지방세포와 조골세포 분화효과를 매개하는 감초의 구성성분을 조사하기 위해 GA(glycyrrhizic acid)와 LA(licochalcone A)의 분화촉진 여부를 확인한 결과, GA는 영향을 주지 않으나 LA가 GBE의 세포분화효과를 매개한다고 사료된다. 따라서 본 연구에서는 제2형 당뇨와 그에 수반되는 골질환과 골다공증에 대한 치료 소재로서 GBE와 그의 생리활성을 매개할 수 있는 LA의 가능성을 보았으며 GBE에서 분리되는 다양한 화합물의 동정 및 생리활성 효과, LA와의 상승효과 등의 추후 연구가 기대된다.

Chemical Bath Deposition of ZnS-based Buffer Layers for Cu2ZnSn(S,Se)4 Thin Film Solar

  • 최희수;박민아;오이슬;전종옥;표성규;김진영
    • 한국진공학회:학술대회논문집
    • /
    • 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
    • /
    • pp.472.1-472.1
    • /
    • 2014
  • 현재 Cu(In,Ga)Se2나 Cu2ZnSn(S,Se)4 (CZTSSe)계 박막태양전지의 버퍼층으로 가장 많이 사용되는 물질은 CdS이다. 하지만 Cd의 독성 문제로 인해 사용에 제약이 있고, CdS의 작은 밴드갭(~2.4 eV)으로 인해 단 파장 영역에서 광활성층의 빛 흡수를 저해하는 문제 때문에 새로운 대체 물질을 찾으려는 연구가 많이 이루어지고 있다. 이러한 관점에서, ZnS계 물질은 독성 원소인 Cd을 사용하지 않고, 3.6 eV 정도의 큰 밴드갭을 가지기 때문에, CdS 버퍼층을 대체하기 위한 물질로 관심을 받고 있다. ZnS계 버퍼층을 증착하는 위해 chemical bath deposition (CBD), molecular beam epitaxy (MBE), thermal evaporation, spray pyrolysis, sputtering, elecrtrodepostion 등의 다양한 공정이 사용될 수 있다. 본 연구에서는 상기의 다양한 공정 가운데, 공정 단가가 낮고, 대면적 공정에 용이한 CBD 공정을 이용하여 ZnS계 버퍼층을 증착하는 연구를 수행하였다. 용액의 조성, 농도, 공정 온도, 시간 등을 비롯한 다양한 공정 변수가 ZnS계 박막의 morphology, 조성, 결정성, 광학적 특성 등 다양한 특성에 미치는 영향이 체계적으로 연구되었다. 또한, 상기 ZnS계 버퍼층을 CZTSSe 박막태양전지에 적용하여 CdS를 성공적으로 대체할 수 있음을 확인하였다. 본 연구를 통하여 ZnS계 버퍼층이 향후 친환경적인 박막태양전지 제조에 활용될 수 있는 가능성을 확인할 수 있었다.

  • PDF

Protein Adsorption and Hydrodynamic Stability of a Dense, Pellicular Adsorbent in High-Biomass Expanded Bed Chromatography

  • Chow, Yen Mei;Tey, Beng Ti;Ibrahim, Mohd Nordin;Ariff, Arbakariya;Ling, Tae Chuan
    • Biotechnology and Bioprocess Engineering:BBE
    • /
    • 제11권3호
    • /
    • pp.268-272
    • /
    • 2006
  • A dense, pellicular UpFront adsorbent ($p=1.5 g/cm^3$, UpFront Chromatography, Cophenhagen, Denmark) was characterized in terms of hydrodynamic properties and protein adsorption performance in expanded bed chromatography. Cibacron Blue 3GA was immobilised into the adsorbent and protein adsorption of bovine serum albumin (BSA) was selected to test the setup. The Bodenstein number and axial dispersion coefficient estimated for this dense pellicular adsorbent was 54 and $1.63{\times}10^{-5}m^2/s$, respectively, indicating a stable expanded bed. It could be shown that the BSA protein was captured by the adsorbent in the presence of 30% (w/v) of whole-yeast cells with an estimated dynamic binding capacity $(C/C_o = 0.01)$ of approximately 6.5 mg/mL adsorbent.