• 한국신재생에너지학회:학술대회논문집
• /
• 2008.10a
• /
• pp.230-233
• /
• 2008

The vanadium rich ash of petroleum coke can give a slagging problem during because of the high melting point of $V_2O_3$. For continuous removal of the slag, petroleum coke is often mixed with coal, and the viscosity of the mixed slag is an important property, determining the gasification temperature. The viscosities of the mixed slag from various mixing ratios of petroleum coke and a bituminous coal were investigated. When mixed with a crystalline coal slag, $T_{cv}$ was increased at a higher the coke content in the mixed feed. When the $V_2O_3$ concentration was greater than 4.5%, it was difficult to get accurate measurements of $T_{cv}$. The SEM/EDX analyses of the cooled slag revealed that the major crystalline phase was anorthite, and $T_{cv}$ should be related to the formation temperature of anorthite. The SEM/EDX analyses also showed that, at low concentrations of vanadium, part vanadium formed a crystalline phase with Al-Si-Ca-Fe, and the rest remained in the glassy phase, suggesting that vanadium existed as a slag component at the low viscosity region. At a high concentration, vanadium forms a phase with Ca, and the Ca-V phase was separated from the slag phase, and formed a layer above the slag. FeO in petroleum coke also played an important role determining viscosity: at high temperatures, increased FeO lowered the viscosity, but as it formed a spinel phase, the depletion of FeO in the slag resulted in a higher viscosity.

• Korean Journal of Metals and Materials
• /
• v.50 no.8
• /
• pp.557-562
• /
• 2012

Self-organized ruthenium (Ru) dots were fabricated by $400^{\circ}C$ RTA (rapid thermal annealing) and ALD (atomic layer deposition). The dots were produced under the $400^{\circ}C$ RTA conditions for 10, 30 and 60 seconds on all Si(100)/200 nm-SiO2, glass, and glass/fluorine-doped tin oxide (FTO) substrates. Electrical sheet resistance, and surface microstructure were examined using a 4-point probe and FE-SEM (field emission scanning electron microscopy). Ru dots were observed when a 30 nm-Ru layer on a Si(100)/200 nm-SiO2 substrate was annealed for 10, 30 and 60 seconds, whereas the dots were only observed on a glass substrate when a 50 nm-Ru layer was annealed on glass. For a glass/FTO substrate, RTA <30 seconds was needed for 30 nm Ru thick films. Those dots can increase the effective surface area for silicon and glass substrates by up to 5-44%, and by 300% for the FTO substrate with a < $20^{\circ}$ wetting angle.

• Journal of the Mineralogical Society of Korea
• /
• v.10 no.2
• /
• pp.105-113
• /
• 1997

Mineral description and mineralogical characterization were made for the wellsite, a barrian zeolite, which found as diagenetic alterations in the Miocene pyroclastic rocks in Gampo area. The wellsite occurs together with clinoptilolite, smectite and apatite as euhedral crystallites (0.2~0.4mm) forming interpenetraion twinning in the vesicles of altered pmice fragments. Compared to other reported wellsites, the wellsite is rather silicic (Si/(Al+Fe): 3.12-3.16) and Ca-rich. Unit cell dimensions and chemical formular determined from XRD, EMPA and TGA data are as follows:a=9.883$\AA$, b=14.204$\AA$, c=8.677$\AA$, $\beta$-124.764$^{\circ}$, (Ba0.57K0.36)(Ca1.18Na0.04)Al3.9Si12.1O32.13.9H2O.The cation composition of the Gampo wellsite, which shows an exchange reaction in the form of Ba2++Ca2+=2(K++Na-), is deviated far from the compositional range of a phillipsite-harmotome series. Due to higher abundance of divalent cations (Ca, Ba) and si in the wellsite, cimpared to those of the phillipsite and harmotome reported in other areas, the zeolite seems to be characteristic of higher water content (18.7 wt%) and higher thermal stability. XRD, chemical and thermo-chemical results of the wellsite reflects that wellsite is rather a Ba- and Ca-rich end member of a phillipsite-harmotome-wellsite series than an intermediate phase of phillipsite-harmotome series or a barrian variety of phillipste.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.13 no.6
• /
• pp.1127-1132
• /
• 2010

Borosilicate glass was prepared in the composition of 81% $SiO_2$, 4% $Na_2O$, 2% $Al_2O_3$, 13% $B_2O_3$. The albite phase($NaAlSi_3O_8$) increased with the $ZrO_2$(0~10wt.%) addition. For measurement of glass transition temperature($T_g$), crystallization temperature($T_{c,max}$) measured by differential thermal analysis. The $T_g$ and $T_{c,max}$ were $510{\sim}530^{\circ}C$ $650{\sim}670^{\circ}C$, respectively. The crystallized glass was heated at various conditions(temperature, time). After nucleation at $550^{\circ}C$ for 2hours prior to crystal growth at $650^{\circ}C$ for 4hours, the resulting Vickers hardness, fracture toughness and bending strength were about $736H_v$, $1.0779MPa{\cdot}m^{1/2}$, and 493MPa, which were 17%, 45% and 149% higher than parent borosilicate glass, respectively. Crystal size and transmittance of crystallized borosilicate glass were analyzed by FE-SEM, EDX and UV-VIS-NIR spectrophotometer. Transmittance of crystallized borosilicate glass was decreased with increasing $ZrO_2$(wt%) at visible-range. The results prove that light-weight bulletproof can be fabricated by the crystallization of borosilicate glass.

• The Journal of the Petrological Society of Korea
• /
• v.6 no.1
• /
• pp.19-33
• /
• 1997

This study reports the results about the petrography and geochemical characteristics of 10 representative volacanic rocks. The Cretaceous volcanic rocks distributed in the vicinity of the Kageo island composed of andesitic rocks, dacitic welded tuff, and rhyolitic rocks in ascending order. Sedimentary rock is the basement in the study area covered with volcanic rocks. Andesitic rocks composed of pyroclastic volcanic breccia, lithic lapilli tuff and cryptocrystallin lava-flow. Most dacitic rocks are lapilli ash-flow welded tuff. Rhyolitic rocks consists of rhyolite tuff and rhyolite lava flow. Rhyolite tuff are lithic crystal ash-flow tuff and crystal vitric ash-flow tuff with somewhat accidental fragments of andesitic rocks, but dacitic rocks. The variation of major and trace element of the volcanic rocks show that contents of $Al_2O_3$, FeO, CaO, MgO, $TiO_2$ decrease with increasing of $SiO_2$. On the basis of Variation diagrams such as $Al_2O_3$ vs. CaO, Th/Yb vs. Ta/Yb, and $Ce_N/YB_N$ vs. $Ce_N$, these rocks represent mainly differentiation trend of calc-alkaline rock series. On the discriminant diagrams such as Ba/La and La/Th ratio, Rb vs. Y + Nb, the volcanic rocks in study area belongs to high-K Orogenic suites, with abundances of trace element and ternary diagram of K, Na, Ca. According to the tectonic discriminant diagram by Wood, these rocks falls into the diestructructive continental margin. K-Ar ages of whole rocks are from andesite to rhyolite $97.0{\pm}6.8~94.5{\pm}6.6,\68.9{\pm}4.8,\61.5{\pm}4.9~60.7{\pm}4.2$ Ma, repectively. Volcanic rocks in study area show well correlation to the Yucheon Group in terms of rock age dating and geochemcial data, and derived from andesitic calc-alkaline magma that undergone low pressure fractional crystallization dominated plagioclase at <30km.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.10
• /
• pp.2597-2605
• /
• 1994

The wear behavior of two types of $Si_3N_4$ exposed to high and low humidity was examined at various sliding speeds, using bearing steel as disk material under pin-on-disk type sliding conditions. Higher wear rates were obtained at a high humidity than at a low humidity. As the sliding speed was increased, the wear rates were decreased and the effect of humidity on the wear rates of $Si_3N_4$ was reduced. The result that the $Si_3N_4$ pin showed higher wear rate under the high humidity condition was explained by the decrease in microhardness of $Si_3N_4$ due to the chemisorbed moisture on the pin and plowing action by the hard particles of $Fe_2O_3$ from the disk. An increase in the sliding speed is supposed to reduce the effect of humidity on the wear rate of $Si_3N_4$ by raising the average temperature of the disk surface and the local temperature at pin-disk contact point.

• Journal of the Korean Ceramic Society
• /
• v.42 no.10 s.281
• /
• pp.672-677
• /
• 2005

In this study we prepared the Sr-ferrite powders and magnet by a molten salt method using the (NaCl+KCl) salt mixture. Starting materials of $Fe_{2}$$O_{3}$ and Sr$Co_{3}$ were mixed as the molar ratio of 5.70:1, and 0.08 mol$ \% $ $Al_{2}$$O_{3}$, 0.10 mo1$ \% $ Si$O_{2}$ and 0.12 mo1$ \% $ CaO were added as additives. Sr-ferrite powders synthesized at the reaction temperatures of 800$\∼$1200$ ^{\circ}C $ showed the typical M-type hexagonal ferrite phase, and hexagonal plate-like morphology with uniform distribution of 1$\∼$3 $\mu$m particle size. The bulk density of the sintered Sr-ferrite magnet prepared with powders by the molten salt method showed the maximum density of 4.82 g/$cm^{3}$ at the sintering temperature of 1200$^{\circ}C $. The maxima of remanent flux density (Br, 45 emu/g) and coercive force (iHc, 3.75 kOe) occurred at the sintering temperatures of 1150$ ^{\circ}C$ and 1200$^{\circ}C $.

• International Journal of Korean Welding Society
• /
• v.3 no.2
• /
• pp.24-28
• /
• 2003

This study was aimed to evaluate the quality of flash welded joints and optimize the welding process for flash butt welding of 780MPa grade high strength steel. And then the relationship between the welding process variables and the joint quality would be established. The effect of process variables between flashing and upsetting process was elucidated. Microstructure observation of the joint indicated that the decarburized band was mainly changed with upsetting process. Width of HAZ was also related to the upsetting conditions rather than the flashing conditions. Generally maximum hardness at HAZ was correlated with Ceq of steel and the empirical relationship was obtained to estimate the HAZ properties. Tensile elongation at the joint was usually decreased with increasing the initial clamping distance. Investigation of fracture surface after tensile and bending tests reveal that the origin of cracking at the joint was oxide inclusions composed of $SiO_2$, MnO, $Al_2O_3$, and/or FeO. The amount of inclusions was dependent on the composition ratio of Mn/Si in steel. If this ratio was above 4, the amount of inclusions was low and then the resistance to cracking at the joint was enough to maintain the joint performance. It was obtained that the flashing process influenced the conditions for the energy input to establish uniform or non­uniform molten layer, while the upsetting conditions influenced the joint strength. Heat input variable during flashing process was also discussed with the joint properties.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.408.2-409
• /
• 2016

Theoretically, the dye-sensitized solar cells (DSSCs) are high efficiency solar cells. However DSSCs have low power conversion efficiency (PCE) than silicon based solar cells. In this study, we use the phosphor materials, such as $Y_2O_3:Eu$ (Red), $Zn_2SiO_4:Mn$ (Green), $BaMgAl_{14}O_{23}:Eu$ (Blue), to enhance the PCE of DSSCs. Three phosphors were prepared and used as an effective scattering layer on the transparent $TiO_2$ with doctor blade method. We confirmed that the three scattering layers improve the PCE and Jsc due to the light harvesting enhancement via increased the scattering and absorbance in visible range. Under the sun illumination AM 1.5 conditions, the PCE of the mesoporous $TiO_2$ based DSSCs is 5.18 %. The PCE of the DSSCs with Y2O3:Eu, $Zn_2SiO_4:Mn$ and $BaMgAl_{14}O_{23}:Eu$ as scattering layer were enhanced to 5.66 %, 5.72% and 5.82%, respectably. In order to compare the optical properties change, DSSCs were measured by EQE, reflectance and PCE. At the same time, FE-SEM and XRD were used to confirm the structural changes of each layer.

• 보존과학연구
• /
• s.26
• /
• pp.165-188
• /
• 2005

From the ancient to these days, there have been used many kinds of pigment which have two types that are inorganic pigment and organic pigment. At the ancient times, natural pigment had been used but the artificially mixed pigment has been used in modern times. By the way, searching for studies has been studied recently, it would be said the ancient pigments such as Danchung, Wall painting and Mural painting are the mainthema. However, studies about the pigments used in modern pictured relics have rarely can be found. Therefore, this analysis of Ilweolokdo would be important at the point of the pigments used in pictures of royal family in modern times and the results can be briefly summarized as below; Firstly, the results of qualitative analysis of the pigments that base or all pigments of picture was detected components of Ca, Fe and As, this results meaning that picture was used filler and basic paint. Secondly, a result of the analysis on the composition elements of the pigments shows that the main components in their composition are ;White - Lead Cyanamide($2PbCO_3$.$Pb(OH)_2$) or Titanium Oxide($TiO_2$)Blue - Ultramarine($2(Na_2O$.$Al_2O_3$ .$2Si_O2$).$Na_2S_2$)Green - Emerald green($C_2H_3A_s3Cu_2O_8$)Gold - Gold(Au), Red-Red Lead($Pb_3O_4$) or Cinnabar(HgS)Black - Carbon(C)Thirdly, X-ray diffraction analysis of crystalline structure for the blue and green pigment peeling off in picture shows that the components of blue pigment is Ultramarine($2(Na_2O$.$Al_2O_3$ .$2Si_O2$).$Na_2S_2$) and green pigment is Emerald green($C_2H_3A_s3Cu_2O_8$). Especially, microcrystalline structure of the green pigment was the shape like a cross section of wood. Consequently, we knew through the analysis of qualitative and microcrystallinestructures seen on the cross section of analyzed pigments layer that the all pigments used in the Ilweoloakdo is possible to use synthetic pigments in modern.