Proceedings of the Korean Vacuum Society Conference
/
2010.08a
/
pp.298-299
/
2010
Cu(In, Ga)Se2 (CIGS) 박막 태양전지는 Soda lime glass/Mo/CIGS/CdS/ZnO/ITO/Al 의 구조를 가지고 있다. CIGS 화합물은 direct bandgap 구조를 하고 있으며, 광흡수율이 다른 어떤 물질들 보다 뛰어나 박막으로도 충분히 태양광을 흡수할 수 있다. 또한 Ga의 도핑 농도에 따른 밴드갭 조절도 가능하다. 이러한 성질들로 인해 현재 박막태양전지로서 20.1%의 최고효율을 가지고 있다.[1] CIGS 박막 태양전지에서 p-CIGS layer와 스퍼터링으로 증착되는 n-ZnO layer사이의 buffer 층으로 chemical bath deposition (CBD)-CdS 박막을 주로 사용한다. CBD-CdS 박막은 n-ZnO 스퍼터로 증착 시킬 때, CIGS 층의 손상을 최소화하고, 이 두 층 사이에서의 격자상수와 밴드갭의 차이를 줄여주어 CIGS 박막태양전지의 효율을 증가 시키는 역할을 한다. 하지만, Cd (카드뮴)의 심각한 독성과 낮은 밴드갭(2.4eV)으로 인해 CIGS 층에서의 광흡수율을 줄여, CdS를 대체할 새로운 buffer 층의 필요성이 대두되었다.[2] 그 대안으로 ZnS, Zn(O, S, OH), (Zn, Mg)O, In2S3 같은 물질이 연구되고 있다. 현재 CBD-ZnS를 buffer 층으로 사용한 CIGS 박막태양전지의 효율은 최고 18.6%로 CBD-CdS의 최고효율보다는 약 1.5% 낮지만, ZnS가 높은 밴드갭(3.7~3.8eV)과 Cd-free 물질이라는 점에서 CdS를 대체할 물질로 각광받고 있다. 본 연구에서는 기존의 CdS 박막을 제조하는 방법과 같은 방법인 CBD를 이용하여 ZnS 박막을 제조하였다. ZnS 박막을 제조하기 위해서는 Zinc sulfate, Thiourea, 암모니아가 사용된다. 암모니아의 mol 농도에 따른 CBD-ZnS/CIGS 박막태양전지의 효율 변화를 관찰하기 위해 암모니아의 mol 농도는 1 mol, 2 mol, 3 mol, 4 mol, 5 mol, 6 mol, 그 이상의 과량을 사용하여 실험하였다. 실험 결과, 암모니아농도 5 mol에서 효율 13.82%를 확인할 수 있었다. 최고효율을 보인 조건인 암모니아 농도가 5 mol 일 때, Voc는 0.602V, Jsc는 33.109mA/cm2, FF는 69.4%를 나타내었다.
Proceedings of the Materials Research Society of Korea Conference
/
2010.05a
/
pp.34.2-34.2
/
2010
Cu(In,Ga)Se2 (CIGS) 화합물 반도체를 기반으로 한 태양전지는 박막태양전지 기술 중 세계최고효율을 기록하고 있다. CIGS를 합성하는 방법은 동시증발법, 스퍼터링/셀렌화 등의 진공방식과 나노분말법, 전착법, 용액법 등의 비진공방식이 있으나, 현재까지 진공방식이 양산기술로서 완성도가 높은 것으로 알려져 있다. 특히 스퍼터링에 의한 전구체 박막 증착과 셀렌 분위기에서의 열처리 공정을 결합시킨 2단계 공정은 동시증발법에 비해 대면적 모듈 제조에 유리한 것으로 알려져 있다. 셀렌화 공정은 통상 반응성이 매우 높은 H2Se 기체를 이용하고 있으나, 부식성 및 안전성 문제를 해결하기 위해 추가적인 설비가 요구되므로 제조비용을 높이는 단점을 갖는다. 한편, Se 증기를 이용하면 안전성은 담보되나 낮은 반응성으로 인해 고온에서 장시간 열처리를 해야하는 문제를 안고 있다. 본 연구에서는 새로운 Se 증기를 사용하되 반응효율을 높일 수 있는 새로운 셀렌화 열처리방법을 제시하고자 한다. 기존의 Se 증기가 별도의 증발원을 이용하여 공급된 것과는 달리, 금속전구체 직상부에 Se이 코팅된 별도의 커버글라스를 위치시켜 Se의 손실을 최대한 억제하였다. Se 커버글라스가 밀착된 금속프리커서를 $200{\sim}600^{\circ}C$ 온도범위에서 열저항가열로 내부에서 열처리하였으며, 추가로 Se을 공급하지는 않았다. 이와 같은 방법 제조된 CIGS 박막의 물성을 X선회절법, 주사전자현미경 등으로 관찰하였으며, 예비실험결과 비교적 낮은 온도에서 chalcopyrite 상이 형성됨을 확인하였다. 근접셀렌화에 의해 제조된 CIGS 박막이 적용된 태양전지를 제조하여 셀렌화 공정변수에 따른 소자특성변화를 제시하고자 한다.
Proceedings of the Korean Vacuum Society Conference
/
2000.02a
/
pp.156-156
/
2000
Recently, the surface electronic states have attracted much attention since their standing wave patterns created around steps, defects, and adsorbates on noble metal surfaces such as Au(111), Ag(110), and Cu(111) were observed by scanning tunneling microscopy (STM). As a typical example, a striking circular pattern of "Quantum corral" observed by Crommie, Lutz, and Eigler, covers a number of text books of quantum mechanics, demonstrating a wavy nature of electrons. After the discoveries, similar standing waves patterns have been observed on other metal and demiconductor surfaces and even on a side polane of nano-tubes. With an expectation that the surface states could be utilized as one of ideal cases for studying two dimensionakl (sD) electronic system, various properties, such as mean free path / life time of the electronic states, have been characterized based on an analysis of standing wave patterns, . for the 2D electron system, electron density is one of the most importnat parameters which determines the properties on it. One advantage of conventional 2D electron system, such as the ones realized at AlGaAs/GaAs and SiO2/Si interfaces, is their controllability of the electrondensity. It can be changed and controlled by a factor of orders through an application of voltage on the gate electrode. On the other hand, changing the leectron density of the surface-state 2D electron system is not simple. On ewqy to change the electron density of the surface-state 2D electron system is not simple. One way to change the electron density is to deposit other elements on the system. it has been known that Pd(111) surface has unoccupied surface states whose energy level is just above Fermi level. Recently, we found that by depositing Pd on Cu(111) surface, occupied surface states of Cu(111) is lifted up, crossing at Fermi level around 2ML, and approaches to the intrinsic Pd surface states with a increase in thickness. Electron density occupied in the states is thus gradually reduced by Pd deposition. Park et al. also observed a change in Fermi wave number of the surface states of Cu(111) by deposition of Xe layer on it, which suggests another possible way of changing electron density. In this talk, after a brief review of recent progress in a study of standing weaves by STM, I will discuss about how the electron density can be changed and controlled and feasibility of using the surface states for a study of 2D electron system. One of the most important advantage of the surface-state 2D electron system is that one can directly and easily access to the system with a high spatial resolution by STM/AFM.y STM/AFM.
Jeong, Chaehwan;Park, Chanyoung;Kim, Jinhyeok;Lee, Suk Ho
한국신재생에너지학회:학술대회논문집
/
2010.06a
/
pp.79-79
/
2010
다른 물질에 비해 많은 우수한 특성을 가지고 있는 CuInSe2(CIS)박막 태양전지는 많은 연구자들에 의해 개발되어 오고 있다. CIS의 대표적인 장점으로는 직접천이형 밴드갭, 높은 흡수계수, 열 안정화상태 및 p형으로의 전도성물질의 가능성 등 다양하다. 또한 간단한 구조를 이용하여 유리같은 싼 기판을 이용하기 때문에 저가형 태양전지로서 많은 각광을 받고 있다. CIGS태양전지는 CIS의 In 사이트에 Ga을 도핑함으로서 만들어지는데 밴드갭은 약 1.4eV이다. CIS박막을 만드는 많은 방법이 존재하나 구성원소로부터 최적화된 조성을 찾을수 있는 방법이 가장 중요한 요소 중의 하나로 인식되고 있으며, 이런점에서 증발법 및 스퍼터링법 등 같은 진공방식이 비진공방식에 비해 훨씬 간편하게 조성비를 맞출수 있다. 그 중에 스퍼터링법은 대면적 박막태양전지로의 가능성으로 비출어 볼때 산업화를 위한 좋은 후보군이 될 수 있다. Selenization을 하기전에 Cu-In-Se의 전구체 조합은 여러개의 타겟으로부터 동시 스퍼터링법이나 다층 전구체법을 사용하여 준비되는데 어떤 방법이 되던지 Se의 부가적인 공급은 불가피하다. 지금까지 많은 관련 연구의 대부분인 구조적, 조성비적 그리고 광학적인 특성평가에 집중되어 오고 있는데, 전기적특성평가의 경우는 면저항, 비저항 같은 간단한 결과 위주로 보고되어 오고 있다. 또한 캐리어농도와 이동도에 대한 보고가 있음에도 불구하고 이해되기에는 충분치 못한 면이 많다.본 발표에서는 태양전지 제조 전단계로서 소다라임유리기판(SLG)위에 Mo의 유무에 따라 CIS박막의 전기적인 특성 변화에 대한 내용을 담고 있다. 소다라임유리($2cm{\times}2cm$)를 기판으로 사용하여 아세톤-에탄올 용액에 초음파세척을 수행하고, Mo 후면전극을 DC 스퍼터링방식을 이용하여 증착을 한다. SLG와 Mo이 코팅된 SLG를 각각 RF 스퍼터 챔버에 이송한 후 수증기 제거를 위해 약 10분간 예열을 한다. 샘플에 대한 전기적특성은 Hall효과 측정장치에 의해 측정이 되며 전기전도도, 캐리어농도, 이동도 및 전도형에 대한 정보가 각각의 변수에 따라 조사된돠. 부가적으로 구조적, 조성비적인 특성을 SEM,XRD 및 EDX를 통해 조사를 하여 전기적 특성에 따른 관계성을 검토한다. SLG와 Mo가 코팅된 SLG위의 CIS박막은 전기적으로 약간 다른 특성을 보일 것으로 예측되며, 이러한 기대를 바탕으로 조성비가 이상적인 화학양론에 근접할 때 p형으로서 제시될 수 있다는 것을 보여줄 것이다.
In this study, the substitution fumigation gases (15% Ethylene Oxide + 85% HFC 134a, 20% Ethylene Oxide + 80% $CO_2$, 99% Sulfuryl Fluoride + 1% Inert Gas) were applied on the metal, pigment, fabric and paper specimen. The result of the fumigation treatment with 15% Ethylene Oxide + 85% HFC 134a (200g/$m^3$, 48hours) is the color changes (${\Delta}E$) of 1st and 2nd Cu specimens showed significant difference as 3.40, 4.17. On the other hand, other specimens except for Cu showed less than 3.0 in chrominance values. The result with 20% Ethylene Oxide + 80% $CO_2$ (150g/$m^3$, 48hours) is that the color changes (${\Delta}E$) of 1st and 2nd specimens were overall less than 3.0 so that color differences were subtle and hardly recognized with naked eyes. So it is proved that the fumigation treatment with Ethylene Oxide 20% + $CO_2$ 80% is relatively stable on materials in this study. In the case of 99% Sulfuryl Fluoride + 1% Inert Gas (50g/$m^3$, 48hours), the color difference of Lead red ($PbO_4$) of pigment was more than 3.0 that was compared with contrast specimens. But chrominance values in the other specimens were less than 3.0 on average.
Proceedings of the Korean Vacuum Society Conference
/
2013.02a
/
pp.543-543
/
2013
Thin-film transistors (TFTs) based on oxide semiconductors have been regarded as promising alternatives for conventional amorphous and polycrystalline silicon TFTs. Oxide TFTs have several advantages, such as low temperature processing, transparency and high field-effect mobility. Lots of oxide semiconductors for example ZnO, SnO2, In2O3, InZnO, ZnSnO, and InGaZnO etc. have been researched. Particularly, zinc-tin oxide (ZTO) is suitable for channel layer of oxide TFTs having a high mobility that Sn in ZTO can improve the carrier transport by overlapping orbital. However, some issues related to the ZTO TFT electrical performance still remain to be resolved, such as obtaining good electrical contact between source/drain (S/D) electrodes and active channel layer. In this study, the bottom-gate type ZTO TFTs with staggered structure were prepared. Thin films of ZTO (40 nm thick) were deposited by DC magnetron sputtering and performed at room temperature in an Ar atmosphere with an oxygen partial pressure of 10%. After annealing the thin films of ZTO at $400^{\circ}C$ or an hour, Cu, Mo, ITO and Ti electrodes were used for the S/D electrodes. Cu, Mo, ITO and Ti (200 nm thick) were also deposited by DC magnetron sputtering at room temperature. The channel layer and S/D electrodes were defined using a lift-off process which resulted in a fixed width W of 100 ${\mu}m$ and channel length L varied from 10 to 50 ${\mu}m$. The TFT source/drain series resistance, the intrinsic mobility (${\mu}i$), and intrinsic threshold voltage (Vi) were extracted by transmission line method (TLM) using a series of TFTs with different channel lengths. And the performances of ZTO TFTs were measured by using HP 4145B semiconductor analyzer. The results showed that the Cu S/D electrodes had a high intrinsic field effect mobility and a low effective contact resistance compared to other electrodes such as Mo, ITO and Ti.
Proceedings of the Korean Institute of Information and Commucation Sciences Conference
/
2010.05a
/
pp.805-808
/
2010
In this paper, CdS thin films, which were widey used window layer of the CdS/CdTe and the CdS/$CuInSe_2$ heterojunction solar cell, were grown by chemical bath deposition, and effects of temperature of reaction solution on the structural properties were investigated. Cadmium acetate and thiourea were used as cadmium and sulfur source, respectively. And ammonium acetate was used as the buffer solution. The reaction velocity was increased with increasing temerature of reaction solution. For temperature <= $85^{\circ}C$, as increasing temperature of solution, deposition rate of CdS films was increased by ion-by-ion reaction in the substrate surface, and the crystallinity of the films was improved. However, for temperature <= $55^{\circ}C$, deposition rate was decreased resulting from smaller Cd2+ ion, and the grain size was decreased.
The NAD(P)H-quinone oxidoreductase (EC 1. 6. 99. 2) was purified from S. cerevisiae. The native molecular weight of the enzyme is approximately 111 kDa and is composed of five identical subunits with molecular weights of 22 kDa each. The optimum pH of the enzyme is pH 6.0 with 1,4-benzoquinone as a substrate. The apparent $k_m$ for 1,4-benzoquinone and 1,4- naphthoquinone are 1.3 mM and $14.3\;{\mu}M$, respectively. Its activity is greatly inhibited by $Cu^{2+}$ and $Hg^{2+}$ ions, nitrofurantoin, dicumarol, and Cibacron blue 3GA. The purified NAD(P)H-quinone oxidoreductase was found capable of reducing aromatic nitroso compounds as well as a variety of quinones, and can utilize either NADH or NADPH as a source of reducing equivalents. The nitroso reductase activity of the purified NAD(P)H-quinone oxidoreductase is strongly inhibited by dicumarol.
CIGS 박막 태양전지는 제조단가가 낮고 박막 태양전지 중에서 변환효율이 가장 높아 발전 가능성이 큰 태양전지로 인식되고 있다. 이미 일본, 독일, 미국을 비롯한 선진국에서는 30-50 MW 급의 양산 라인이 구축되고 있어 2010년 이후에는 본격적인 상용화가 진행될 것으로 보인다. CIGS 광흡수층은 진공증발, 셀렌화, 나노입자, 전기도금등 다양한 방식으로 제조가 가능한데 이 중에서도 동시진공증발공정은 고효율 CIGS 박막 태양전지 제조에 적합하다. 본 연구에서는 동시진공증발법을 이용하여 CIGS 박막을 증착하였으며 소다회유리/Mo/CIGS/CdS/i-ZnO/n-ZnO/Al/AR 구조의 태양전지를 제조하였다. 기판온도 모니터링을 통한 Cu 이차상 조절 기술을 이용하여 결정립이 매우 큰 CIGS 박막을 증착하였으며 Ga/(In+Ga) 조성비의 조절을 통하여 밴드갭 에너지를 최적화하였다. 또한 QCM 장치를 활용하여 용액 속에서 성장되는 CdS 박막의 두께와 특성을 조절하였다. 이러한 공정최적화를 통하여 개방전압 0.65 V, 단락전류밀도 38.8 $mA/cm^2$, 충실도 0.74 그리고 변환효율 18.8% 의 CIGS 박막 태양전지를 얻었다.
Proceedings of the Materials Research Society of Korea Conference
/
2011.10a
/
pp.35.1-35.1
/
2011
New photovoltaic (PV) materials and manufacturing approaches are needed for meeting the demand for lower-cost solar cells. The prototypal thin-film photovoltaic absorbers (CdTe and $Cu(In,Ga)Se_2$) can achieve solar conversion efficiencies of up to 20% and are now commercially available, but the presence of toxic (Cd,Se) and expensive elemental components (In, Te) is a real issue as the demand for photovoltaics rapidly increases. To overcome these limitations, there has been substantial interest in developing viable alternative materials, such as $Cu_2ZnSnS_4$ (CZTS) is an emerging solar absorber that is structurally similar to CIGS, but contains only earth abundant, non-toxic elements and has a near optimal direct band gap energy of 1.4~1.6 ev and a large absorption coefficient of ${\sim}10^4\;cm^{-1}$. The CZTS absorber layers are grown and investigated by various fabrication methods, such as thermal evaporation, e-beam evaporation with a post sulfurization, sputtering, non-vacuum sol-gel, pulsed laser, spray-pyrolysis method and electrodeposition technique. In the present work, we report an alternative method for large area deposition of CZTS thin films that is potentially high throughput and inexpensive when used to produce monolithically integrated solar panel modules. Specifically, we have developed an aqueous chemical approach based on chemical bath deposition (CBD) with a subsequent sulfurization heat treatment. Samples produced by our method were analyzed by scanning electron microscopy, X-ray diffraction, transmission electron microscopy, absorbance and photoluminescence. The results show that this inexpensive and relatively benign process produces thin films of CZTS exhibiting uniform composition, kesterite crystal structure, and good optical properties. A preliminary solar cell device was fabricated to demonstrate rectifying and photovoltaic behavior.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.