• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2011.05a
• /
• pp.142-142
• /
• 2011

Epitaxial $CuCrO_2$ thin films have been grown on single crystal substrate of c-plane $Al_2O_3$, $SrTiO_3$, YSZ and Quarts by laser ablation of a $CuCrO_2$ target using 266nm radiation from a Nd:YAG laser. X-ray measurements indicate that the $CuCrO_2$ grows epitaxially on all substrate, with its orientation dependent on the kinds of substrates. Most of the layer were polycrystalline with (001), (015) and random as the dominant surface orientation on c-plane YSZ, $SrTiO_3$ and quarts substrate, respectively. (001) orientated $CuCrO_2$ grows on C-plane $Al_2O_3$ and YSZ substrate, (015) orientated $CuCrO_2$ films are found on c-plane $SrTiO_3$ substrate and random orientated $CuCrO_2$ films grows on quarts substrate. These data are compared with the in-plane orientation and the mismatch of the $CuCrO_2$ and each substrate lattices in an attempt to relate the preferred orientation to the plane of the sapphire on which it is grown. Further characterization show that the grain size of the films increases for a substrate temperature increase, whereas the electrical properties of $CuCrO_2$ thin films depend upon their crystalline orientation.

• Journal of Korean Ophthalmic Optics Society
• /
• v.3 no.1
• /
• pp.223-228
• /
• 1998

Glass films of $SiO_2-TiO_2-M_xO_y$ (M = Co, Cr or Cu) have been prepared on soda-lime-silica slide glasses by the chemical solution method using a spin-coating technique. Commercially available tetraethyl orthosilicate, titanium trichloride, and cobalt-, chromium- and copper-nitrates were used as starting materials. No crystalline segregations of $Co_3O_4$, $Cr_2O_3$ and CuO were observed by X-ray diffraction ${\theta}-2{\theta}$ scans. From the optical transmission analysis, cobalt existed as $ Co^{2+}$ in tetrahedral coordination, chromium as $Cr^{6+}$ in tetrahedral symmetry and copper as $Cu^{2+}$ in octahedral coordination. Films with a crack-free and no texture exhibited homogeneous interfaces between the films and the substrates along the cross-section.

• Journal of Hydrogen and New Energy
• /
• v.7 no.2
• /
• pp.147-155
• /
• 1996

The aim of this study is the development of technologies of methanol production from carbon dioxide by catalytic hydrogenation. Experiments about carbon dioxide hydrogenation by catalyst mixed with CuO, ZnO, $Cr_2O_3$ and $Al_2O_3$ were conducted to find optimum catalyst and reaction condition. Reactions were carried out at atmospheric and high pressures between 200 to $350^{\circ}C$. High yield of methanol was obtained with $Cu/ZnO/Cr_2O/Cr_2O_3/Al_2O_3$ catalyst at $250^{\circ}C$ and above 30 atmospheric pressure. There was not any increament of hydrogenation reactivity for the catalysts which was made by the addition of Pd to $Cu/ZnO/Cr_2O/Cr_2O_3/Al_2O_3$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.256-256
• /
• 2010

투명전극부터 디스플레이 산업에 이르기까지 광범위하게 응용되어지고 있고 개발되어지고 있는 투명전도산화물(TCO)은 ZnO, In2O3, SnO2 등을 기본으로 하는 n-type 재료가 대부분이다. 그러나 투명전도 산화물을 이용한 light emitting diode(LED), 투명한 태양전지, p-형 TFT와 같은 투명전자소자의 개발을 위해서는 p-type 소재가 필수적이다. p-type TCO 소재는 비교적 연구 개발 실적이 매우 부진한 실정이었다. 1997년 넓은 밴드갭을 가지는 ABO2(delafossite) 산화물이 p-type으로서 안정적이라는 것을 보고함에 따라 이에 대한 연구가 활발히 진행되고 있다. 현재 ABO2 형태를 가진 Delafossite구조 산화물이 가장 유망한 p-type 투명전도체 소재로 거론되고 있다. Delafossite 구조가 p-type 투명전도체에 적합한 결정구조인 이유는 밴드갭이 넓고 공유결합에 유리하기 때문이다. Delafossite구조는 상온에서 2종류의 polytype(상온에서 Rhombohedaral구조와 hexagonal 구조)이 존재하며 이들은 각각 3R 및 2H의 결정 구조를 가지고 있다. ABO2의 delafossite구조에서 Cu+의 배열은 c-축을 따라 Cu-O-Cr-O-Cu의 연속적인 층 구조로서 2차원연결로 보여 진다. 보고된 Cu- base delafossite구조를 가지는 재료들은 CuAlO2, CuGaO2, CuInO2 등 여러가지가 있다. 본 연구에서는 PLD를 이용하여 c-plane 사파이어 기판위에 성장된 delafossite구조인 CuCrO2박막의 특성을 알아보았다. p-type 특성을 위하여 CuCrO2에 Zn를 첨가하였으며 그에 따른 구조적 전기적 특성을 조사하였다. 성장온도와 산소분압을 $500{\sim}700^{\circ}C$, 0~10mTorr로 변화시켜 특성을 연구하였다. 성장온도 $700^{\circ}C$, 산소분압 10mTorr에서 c-plane 사파이어 기판위에 c-축 배향의 에피성장된 CuCrO2:Zn 박막을 얻을 수 있었다. Mg를 도핑함에 따른 p-type 특성보다 현저히 떨어지는 것을 확인하였다. 또한 동일한 조건임에도 특정한 이차상의 존재를 통해 도핑된 Zn의 위치를 추측할 수 있었다. 온도와 분압에 따른 결정성과 표면상태를 SEM을 통해서 확인하였다.

• Transactions of Materials Processing
• /
• v.7 no.5
• /
• pp.465-473
• /
• 1998

The effect of alloying elements of Ag-Cu-Zr-X brazing alloy on the microstructure and the bond strength of $Al_2O_3/Ni-Cr$ brazed steel joint was investigated. The reaction layer, $ZrO_2$ (a=5.146 ${\AA}$ , b=5.213 ${\AA}$ , c=5.311 ${\AA}$ )was formed at the interface of $Al_2O_3/Ni-Cr$ steel joint by the redox reaction between alumina and Zr. The addition of An and Al to the Ag-Cu-Zr brazing alloy gave rise to changes in the thickness of the reaction product layer and the morphology of the brazement. Sn caused the segregation of Zr was decreased b Al the $ZrO_2$ layer formed at the Ag-Cu-Zr-Al alloy was thinner than that of $ZrO_2$ formed at the Ag-Cu-Zr-An alloy. The fracture shear strength was strongly dependent on the microstructure of the brazement. Brazing with Ag-Cu-Zr-Sn alloy resulted in a better bond strength than with Ag-Cu-Zr or Ag-Cu-Zr-Al alloy.

• Journal of Surface Science and Engineering
• /
• v.42 no.2
• /
• pp.68-72
• /
• 2009

We report on the growth of $CuCrO_2$ films using pulsed laser deposition and their structural and electrical transport properties. $CuCrO_2$ thin films were doped with 5 at% Mg for p-type properties. Epitaxial films of $CuCr_{0.95}Mg_{0.05}O_2$ were grown on c-plane sapphire substrates. The effects of growth temperature and oxygen pressure on film properties were investigated. The main phase of delafossite $CuCr_{0.95}Mg_{0.05}O_2$ was appeared above the growth temperature of $600^{\circ}C$. The thin film grown at $500^{\circ}C$ showed the highest conductivity, reaching 19.6 S/cm while higher growth temperatures over $500^{\circ}C$ led to lower conductivity; the thin film grown at $700^{\circ}C$ showed 0.02 S/cm.

• Journal of the Korean Society for Heat Treatment
• /
• v.31 no.4
• /
• pp.171-179
• /
• 2018

Copper powder dispersed with 4 vol.% of $Cr_2O_3$ was successfully produced by a simple milling at 210 K with a mixture of $Cu_2O$, Cu and Cr elemental powders, followed by Hot Pressing (HP) at 1123 K and 50 MPa for 2h to consolidate the milled powder. The microstructure of the HPed material was characterized by standard metallographic techniques such as XRD (X-ray Diffraction), TEM and STEM-EDS. The results of STEMEDS analysis showed that the HPed materials comprised a mixture of nanocrystalline Cu matrix and $Cr_2O_3$ dispersoid with a homogeneous bimodal size distribution. The mechanical properties of the HPed materials were characterized by micro Vickers hardness test at room temperature. The thermodynamic considerations on the heat of formation, the incubation time to ignite MSR (Mechanically induced Self-sustaining Reaction), and the adiabatic temperature for the heat of displacement reaction between the oxide-metal are made for the delayed formation of $Cr_2O_3$ dispersoid in terms of MSR suppression. The results of TEM observation and hardness test indicated that the relatively large dispersoids in the HPed materials are attributed to the significant coarsening for the high temperature consolidation; this leads to the low Vickers hardness value. Based on the thermodynamic calculation for the operating processes with a limited number of parameters, the formation kinetics and coarsening of the $Cr_2O_3$ dispersoid are discussed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.210-210
• /
• 2010

ABO2 형태를 가진 delafossite 구조 산화물은 p-type 투명전도체 소재로 유명하다. Delafossite 구조가 p-type 투명전도체에 적합한 결정적인 이유는 밴드갭이 넓고 공유결합에 유리하기 때문이다. 투명전도체는 가시광선의 흡수가 없도록 band gap을 넓히는 것이 우선인데 이러한 band gap이 넓은 구조가 delafossite이다. 또한 delafossite 구조는 구조적으로 각각의 산화물 이온들이 유사 사면체 배위(pseudo-tetrahedral coordination)을 갖는다. 이러한 사면체 배위결합구조에서 산소이온은 비결합면이 없기 때문에 더욱더 공유결합성을 향상시킬 것으로 생각된다. 여기서 A는 +1가 cation, B은 +3가 cation으로 구성되어 있다. A자리에는 1가 원소인 팔라듐, 플래티늄, 은, 구리 등을 가질 수 있고. B자리에 3가 원소이면서도 크기가 알루미늄보다는 크고 란타늄보다는 작은 금속이 들어갈 수 있다. Delafossite 구조는 상온에서 2종류의 polytype (상온에서 Rhombohedaral 구조와 hexagonal 구조)이 존재하며 이들은 각각 3R(Rm) 및2H (P63/mmc)의 결정 구조를 가지고 있다. CuCrO2는 일반적으로 3R결정구조를 가지는 것으로 알려져 있다. delafossite 구조는 전기적 이방성을 띄고 있는데 c-축 방향으로의 전기적 특성이 a-축 방향으로의 전기적 특성보다 약 1000배 높은 물성을 띈다고 한다. 이는 c-축 방향의 원자 위치 때문인데 CuCrO2의 경우 Cu-O-Cr-O-Cu로서 3d-2p-3d-2p-3d 궤도를 가지기 때문인 것으로 알려져 있다.[ref] 반면 c-축으로 에피성장된 박막의 경우 +3가 이온이 위치한 layer에서 hole hopping에 의해 캐리어가 전도된다고 알려져 있기도 하다. 본 연구에서는 PLD를 이용하여 c-plane 사파이어 기판위에 성장된 delafossite구조인 CuCrO2박막의 특성을 알아보았다. p-type 특성을 위하여 CuCrO2에 Ni를 첨가하였으며 그에 따른 구조적 전기적 특성을 조사하였다. 성장온도와 도핑농도를 변화시켜 특성을 연구하였다. 결정구조적 특성과 전기적 특성을 분석하려 한다.

• Journal of the Korean Society for Heat Treatment
• /
• v.15 no.1
• /
• pp.21-24
• /
• 2002

The electrode materials for welding machine in automobile industry such as Cu-Cr, Cu-Zr and Cu-$Al_2O_3$ require the high electrical conductivity and the proper hardness. Therefore the effects of solution heat treatment and aging treatment on the electrical conductivity and hardness of Cu-0.8wt%Cr and Cu-1.2wt%Cr alloys have been investigated. Cu-0.8wt%Cr alloy showed the higher electrical conductivity and hardness than Cu-1.2wt%Cr alloy and both alloys showed the better electrical conductivity at $930^{\circ}C$ among 930, 980 and $1030^{\circ}C$ solution heat treatment temperatures. The electrical conductivity and hardness in both alloys were not affected by aging treatment but remarkably affected by solution heat treatment temperature. The final drawing process reduced electrical conductivity and increased hardness more in Cu-1.2wt%Cr alloy.

• Progress in Superconductivity and Cryogenics
• /
• v.24 no.4
• /
• pp.25-28
• /
• 2022

We investigated the formation of superconducting intergrowth phases through the interface reaction both between TlSr₂Cu₁O₅ (Tl-121) and (CrO₄)Sr₂CuO₂, and between Tl -121 and ((CO₃)_0.5(CrO₄)_0.5 Sr₂CuO₂ phases. We found oxychromate intergrowth phases can be formed through the interface reactions and a new superconducting oxychromate compound TlSr₄Cu₂O_z(CO₃)_0.5(CrO₄)_0.5 with T_c above 73 K was discovered based on the results of the interface reactions.