• Bulletin of the Korean Chemical Society
• /
• 제13권6호
• /
• pp.605-612
• /
• 1992

Chromium oxide/zirconia catalysts were prepared by dry impregnation of powdered $Zr(OH)_4$ with ($NH_4$)$_2$CrO$_4$aqueous solution. The characterization of prepared catalysts was performed using FTIR, XPS, XRD and DTA methods, and by the measurement of surface area. The addition of chromium oxide to zirconia shifted the transitions of $ZrO_2$ from amorphous to tetragonal phase and from tetragonal to monoclinic phase to higher temperature due to the strong interaction between chromium oxide and zirconia, and the specific surface area of catalysts increased in proportion to the chromium oxide content. Since the $ZrO_2$ stabilizes supported chromium oxide, chromium oxide was well dispersed on the surface of zirconia, and ${\alpha}$-$Cr_2O_3$ was observed only at the calcination temperature above 1173 K. Upon the addition of only small amount of chromium oxide (1 wt% Cr) to $ZrO_2$, both the acidity and acid strength of catalyst increased remarkably, showing the presence of two kinds of acid sites on the surface of $CrO_x$/$ZrO_4$-Bronsted and Lewis.

• Journal of Welding and Joining
• /
• 제25권4호
• /
• pp.28-34
• /
• 2007

The heating unit of direct heating method manufactured as the plasma spray coating of $TiO_2/NiCr$ conductive heating material on the surface of heating unit in order to improve the disadvantages of indirect heating method. $TiO_2$ and NiCr (80wt.%Ni-20wt.%Cr) that had the properties of conduction and heating was chosen for the conductive heating material. The compositions of the composite powders were studied $TiO_2-30wt.%NiCr\;and\;TiO_2-10wt.%NiCr$. As the heating temperature was increased, the hardness of heating layer was increased because of the fine microstructure and the decrease of porosity. The adhesion strength was decreased for coarsening and connection of voids in the insulation layer, and the electrical resistivity of heating layer was increased for fine crack formation and growth. In this study, the best efficient sprayed coatings with heating unit was concluded as the plasma sprayed $TiO_2-10wt.%NiCr$ coatings that was heat treated at $300^{\circ}C$.

• 한국표면공학회지
• /
• 제54권2호
• /
• pp.43-52
• /
• 2021

The Ni-based superalloy, Inconel 740, was corroded between 800 and 1100℃ for up to 100 hr in air and Ar-0.2%SO₂ gas in order to study its corrosion behavior in air and sulfur/oxygen environment. It displayed relatively good corrosion resistance in both environment, because its corrosion was primarily dominated by not sulfidation but oxidation especially in Ar-0.2%SO₂ gas. Such was attributed to the thermodynamic stability of oxides of alloying elements when compared to corresponding sulfides. The scales consisted primarily of Cr₂O₃, together with some NiAl₂O₄, MnCr₂O₄, NiCrMnO₄, and rutile-TiO₂. Sulfur from SO₂ gas made scales prone to spallation, and thicker. It also widened the internal corrosion zone when compared to air. The corrosion resistance of IN740 was mainly indebted to the formation of protective Cr₂O₃-rich oxides, and suppression of the sulfide formation.

• E2M - 전기 전자와 첨단 소재
• /
• 제3권4호
• /
• pp.279-286
• /
• 1990

고출력 변환기재료로 이용하기 위하여 유전손실에 기인한 압전 특성의 열화를 방지할 수 있는 큐리점이 비교적 높은 Pb$_{2}$FeNbO$_{6}$의 제3성분을 PZT에 고용한 고용체에서 양호한 압전특성을 갖는 조성을 찾고, 기계적 품질계수를 개선하고자 Cr$_{2}$O$_{3}$를 첨가한 변성 3성분계에 대하여 조사하였다. 그 결과, 전기기계결합계수가 가장 큰 조성은 0.05Pb(FeNb)O$_{3}$-0.4275PbTiO$_{3}$-0.5225 PbZrO$_{3}$이었으며 이조성의 기계적 품질계수, 상전이점은 170, 399.deg.C이었으며 이조성에 0.1wt% Cr$_{2}$O$_{3}$첨가한 변성 3성분계의 기계적 품질계수는 320으로 개선되었다.

• Nuclear Engineering and Technology
• /
• 제49권1호
• /
• pp.178-188
• /
• 2017

To study the effects of zirconium (Zr) addition on the microstructure, hardness and the tensile properties of oxide dispersion strengthened (ODS) ferritic-martensitic steels, two kinds of 9Cr-ODS ferritic-martensitic steels with nominal compositions (wt.%) of $Fe-9Cr-2W-0.3Y_2O_3$ and $Fe-9Cr-2W-0.3Zr-0.3Y_2O_3$ were fabricated by the mechanical alloying (MA) of premixed powders and then consolidated by hot isostatic pressing (HIP) techniques. The experimental results showed that the average grain size decreases with Zr addition. The trigonal ${\delta}$-phase $Y_4Zr_3O_{12}$ oxides and body-centered cubic $Y_2O_3$ oxides are formed in the 9Cr-Zr-ODS steel and 9Cr non-Zr ODS steel, respectively, and the average size of $Y_4Zr_3O_{12}$ particles is much smaller than that of $Y_2O_3$. The dispersion morphology of the oxide particles in 9Cr-Zr-ODS steel is significantly improved and the number density is $1.1{\times}10^{23}/m^3$ with Zr addition. The 9Cr-Zr-ODS steel shows much higher tensile ductility, ultimate tensile strength and Vickers hardness at the same time.

• 한국세라믹학회지
• /
• 제33권11호
• /
• pp.1285-1291
• /
• 1996

Using Cr2O3 Al and graphite powders as starting materials Cr3C2 was synthesized by combustion synthesis process according to the following reaction : 3Cr3C2 +4C+6Allongrightarrow2Cr3C2 +3Al2O3. The synthesis was conducted at 2 atm in an argon atmosphere. in this study main-product was monolithic phase of Cr3C2 /Cr7C3 mixture and sub-product was slag state of $\alpha$-Al2O3. Single phase of Cr3C2 was obtained when crushed main-product was heat-treated at 120$0^{\circ}C$ for 3h in vacuum state with addition of 2.5wt% C. The obtained Cr3C2 powder can be used as plasma-arc deposit material because the flowability index of powder with the size of 9-50${\mu}{\textrm}{m}$ was 66.

• 한국표면공학회지
• /
• 제40권5호
• /
• pp.219-224
• /
• 2007

The corrosion characteristics of Fe-18Cr-10Ni steels were studied between $600^{\circ}C$ and $1000^{\circ}C$ in Ar+(0.2, 1)%$SG_2$ gas for up to 300 hr in order to employ Fe-18Cr-10Ni steels in the coal-fired power plants. The corrosion resistance of Fe-18Cr-10Ni steels was good due mainly to the high amount of Cr, which formed $Cr_2O_3$ from the initial corrosion stage. Fe in the steels corroded to mainly $Fe_2O_3$ and $Fe_3O_4$. Ni was not susceptible to corrosion under the current corrosion condition. Relatively thin, single-layered scales formed.

• Journal of Magnetics
• /
• 제13권4호
• /
• pp.163-166
• /
• 2008

Multiferroic $CoCr_2O_4$ film was deposited on MgO and $MgAl_2O_4$ substrates by the rf-sputtering process. The films were prepared at an RF-magnetron sputtering power of 50 W and a pressure of 10 mtorr (20 sccm in Ar), and at substrate temperatures of $550^{\circ}C$. The crystal structure was determined to be a spinel (Fd-3m) structure by means of X-ray diffraction (XRD) with Cu $K{\yen}{\acute{a}}$ radiation. The thickness and morphology of the films were measured by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The magnetic properties were measured using a Superconducting Quantum Interference Device (SQIUD) magnetometer. While the ferrimagnetic transitions were observed at about 93 K, which was determined as the Neel temperature, the magnetic properties all show different behaviors. The differences between the magnetic properties can be explained by the stress effects between $CoCr_2O_4$ and the substrates of MgO and $MgAl_2O_4$.

• E2M - 전기 전자와 첨단 소재
• /
• 제9권9호
• /
• pp.900-905
• /
• 1996

We have investigated dielectric properties of low fired ceramics BiNbO$_{4}$ containing 0.05[wt%] V$_{2}$O$_{5}$ and x[wt%l Cr$_{2}$O$_{3}$ (x=0, 0.2, 0.4, 0.8, 1.2). By substituting Cr for Bi, dielectric constant .epsilon.$_{r}$ and quality factor Q.f increased and temperature coefficient of resonant frecquency .tau.$_{f}$ changed to positive value. In the composition of BiNbO$_{4}$+0.05 [Wt%] V$_{2}$O$_{5}$+0.8[wt%]Cr$_{2}$O$_{3}$ sintered at 960[.deg. C], we could obtain microwave dielectric properties of .epsilon.$_{r}$=49, Q.f.simeq.3000[GHz](at 4.8[GHz]), .tau.$_{f}$.simeq.0[ppm/.deg. C]. As the above ceramics can be sintered near 960[.deg. C], it is applicable to multilayer microwave device with Ag conductor.tor.tor.tor.

• 한국수소및신에너지학회논문집
• /
• 제21권4호
• /
• pp.301-306
• /
• 2010

The present work is performed to photocatalytically reduce Cr(VI) by means of metal deposited anodized $TiO_2$ tubes, which are prepared by anodization of Ti foil followed by metal deposition. Stably immobilized photo-reactive materials are favored in the field of detoxification in a conventional aqueous medium, preventing gradual loss of efficiency and process malfunction due to detachment of the materials. The prepared samples are characterized by SEM, TEM, EDAX, and photocurrent. The metal deposited-$TiO_2$ electrode shows higher efficiency for Cr(VI) reduction (ca. 20%) and higher ability for adsorption (4~5 times) than pure one.