• Journal of the Korean Ceramic Society
• /
• v.55 no.2
• /
• pp.166-173
• /
• 2018

In order to investigate the effect of Mn on the dielectric and piezoelectric properties of PMN-PT [$Pb(Mg_{1/3}Nb_{2/3})O_3-PbTiO_3$], four different types of 71PMN-29PT samples were prepared using the solid-state single crystal growth (SSCG) method: (1) Undoped single crystals, (2) undoped polycrystalline ceramics, (3) Mn-doped single crystals, and (4) Mn-doped polycrystalline ceramics. In the case of single crystals, the addition of 0.5 mol% Mn to PMN-PT decreased the dielectric constant ($K_3{^T}$), piezoelectric charge constant ($d_{33}$), and dielectric loss (tan ${\delta}$) by about 50%, but increased the coercive electric field ($E_C$) by 50% and the electromechanical quality factor ($Q_m$) by 500%, respectively. The addition of Mn to PMN-PT induced an internal bias electric field ($E_I$) and thus specimens changed from piezoelectrically soft-type to piezoelectrically hard-type. This Mn effect was more significant in single crystals than in ceramics. These results demonstrate that Mn-doped 71PMN-29PT single crystals, because they are piezoelectrically hard and simultaneously have high piezoelectric and electromechanical properties, have great potential for application in fields of SONAR transducers, high intensity focused ultrasound (HIFU), and ultrasonic motors.

• Journal of the Korean Ceramic Society
• /
• v.38 no.4
• /
• pp.307-307
• /
• 2001

Combustion process with citrate was used to produce the LiMn$_2$O$_4$powder. Precursors are pre-ignited in open air followed by post-heating in the range from $600^{\circ}C$ to 80$0^{\circ}C$ for 4h. With varying the molar ratio (R) of ethylene glycol (EG) to citric acid (CA) from 0 to 4, the effect of EG content on powder characteristics is evaluated. Vacuum drying promote the auto-ignition at room temperature. With small addition of EG metal ion was selectively segregated with organic substances and undesired lithium evaporation occurred during post-heating. LiMn$_2$O$_4$phase which is produced by combustion reaction was decomposed back to Mn$_3$O$_4$because the reaction temperature was higher than 95$0^{\circ}C$. With increasing EG content, the homogeneity of LiMn$_2$O$_4$powder increased and specific surface area increased. And lithium evaporation during vacuum drying and/or ignition also increased.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1794-1796
• /
• 2000

Oxides of the form $Mn_{3}O_4$-$Co_{3}O_4$-NiO present properties that make them useful as multilayer chip NTC thermistor for mobile communication telephone. When $Mn_{2}Ni_{x}CO_{1-x}O_4$ composition with the X = 0.12$\sim$0.24 at sintered temperature 1250$^{\circ}C$, resistivity and B-constant were 300$\sim$450[${\Omega}-cm$] and 3250$\sim$3450, respectively. Multilayer chip NTC(Negative Temperature Coefficient) resistor were fabricated with 4 layer by a conventional multilayer capacitor techniques, using 100 pd paste as internal electrode and $Mn_{2}Ni_{0.20}CO_{0.8}O_4$ composition as NTC materials. In particular, resistance change ratio (${\Delta}R$), the important factor for reliability, varied within $\pm$3%, indicating the compositions of multilayer chip NTC thermistor products could be available for mobile communication telephone.

• Journal of the Microelectronics and Packaging Society
• /
• v.15 no.1
• /
• pp.1-6
• /
• 2008

Thermoelectric properties of calcium cobalt layer structure oxide system, $Ca_3Co_2O_6$ and $Ca_3Co_4O_9$ were investigated at the temperature range of 300 to 1000K for the application of thermoelectric generation. In the composition, the Ca site was partially substituted with Bi, Sr, La, K and the Co site was partially substituted with Mn, Fe, Ni, Cu, Zn. The thermoelectric properties of Bi substituted $Ca_3Co_4O_9$. $Ca_{2.7}Bi_{0.3}Co_4O_9$ for electrical conductivity, Seebeck coefficient and power factor were $85.4({\Omega}$cm)^{-l}, $176.2{\mu}V/K$ and $265.2{\mu}W/K^m$, respectively. The unit thermoelectric couple was fabricated with the p-type of $Ca_{2.7}Bi_{0.3}Co_4O_9$ and n-type ($Zn_{0.98}Al_{0.02}$)O thermoelectrics whose figure-of-merit(Z) were $0.87{\times}10^{-4}/K$ and $0.41{\times}10^4/K$, respectively. The generated thermoelectric power was about 30mV at the temperature difference of 120K in the unit thermoelectric couple.

• Korean Journal of Mineralogy and Petrology
• /
• v.34 no.2
• /
• pp.107-120
• /
• 2021

The Komdok Pb-Zn deposit, which is the largest Pb-Zn deposit in Korea, is located at the Hyesan-Riwon metallogenic zone in Jiao Liao Ji belt included Paleoproterozoic Macheolryeong group. The geology of this deposit consists of Paleoproterozoic metasedimentary rocks, Jurassic Mantapsan intrusive rocks and Cenozoic basalt. The Komdok deposit which is a SEDEX type deposit occurs as layer ore and vein ore in the Paleoproterozoic metasedimentary rocks. Based on mineral petrography and paragenesis, dolomites from this deposit are classified four types (1. dolomite (D₀) as hostrock, 2. early dolomite (D₁) associated with tremolite, actinolite, diopside, sphalerite and galena from amphibolite facies, 3. late dolomite (D₂) associated with talc, calcite, quartz, sphalerite and galena from amphibolite facies, 4. dolomite (D₃) associated with white mica, chlorite, sphalerite and galena from quartz vein). The structural formulars of dolomites are determined to be Ca_1.00-1.20Mg_0.80-0.99Fe_0.00-0.01Zn_0.00-0.02(CO₃)₂(D₀), Ca_1.00-1.02M_0.97-0.99Fe_0.00-0.01Zn_0.00-0.02(CO₃)₂(D₁), Ca_0.99-1.03Mg_0.93-0.98Fe_0.01-0.05Mn_0.00-0.01As_0.00-0.01(CO₃)₂(D₂) and Ca_0.95-1.04Mg_0.59-0.68Fe_0.30-0.36Mn_0.00-0.01 (CO₃)₂(D₃), respectively. It means that dolomites from Komdok deposit have higher content of trace elements (FeO, MnO, HfO₂, ZnO, PbO, Sb₂O₅ and As₂O₅) compared to the theoretical composition of dolomite. These trace elements (FeO, MnO, ZnO, Sb₂O₅ and As₂O₅) show increase and decrease trend according to paragenetic sequence, but HfO₂ and PbO elements no show increase and decrease trend according to paragenetic sequence. Dolomites correspond to Ferroan dolomite (D₀, D₁ and D₂), and Ferroan dolomite and ankerite (D₃), respectively. Therefore, 1) dolomite (D₀) as hostrock was formed by subsequent diagenesis after sedimentation of Paleoproterozoic (2012~1700 Ma) silica-bearing dolomite in the marine evaporative environment. 2) Early dolomite (D₁) was formed by hydrothermal metasomatism origined metamorphism (amphibolite facies) associated with intrusion (1890~1680 Ma) of Paleoproterozoic Riwon complex. 3) Late dolomte (D₂) was formed from residual fluid by a decrease of temperature and pressure. and dolomite (D₃) in quartz vein was formed by intrusion (213~181 Ma) of Jurassic Mantapsan intrusive rocks.

• Journal of Sensor Science and Technology
• /
• v.17 no.4
• /
• pp.303-307
• /
• 2008

$NiO,\;Cu_2O,\;Mn_2O_3$ and $Cr_2O_3$ as p-type semiconductors were added in CoO with 15 wt.% ethylene glycol binder and measured the butane gas sensing characteristics. The highest sensitivity is obtained for the NiO-CoO sensors. CoO-20 at.% NiO sensor with 15 wt.% ethylene glycol binder sintered at $1100^{\circ}C$ for 24 h exhibits high sensitivity of 90 % to 5000 ppm butane gas at the sensor temperature of $250^{\circ}C$, compared to low sensitivities at the low operating temperature for commercial sensors. Response and recovery times are, respectively, within few seconds and 1min in the static flow system, indicating rapid adsorption and desorption of butane gas on sensor surface even at this low temperature.

• Journal of the Korean Ceramic Society
• /
• v.39 no.9
• /
• pp.829-834
• /
• 2002

Ferroelectric properties of $ErMnO_3$ thin films deposited on Si(100) substrate using Sol-gel process with metal salts were investigated. $ErMnO_3$ thin films with a (001) preferred orientation were crystallized at 800$^{\circ}C$. The $ErMnO_3$ thin film post-annealed at 800$^{\circ}C$ for 1 h showed the dielectric constant(k) of 26 and the dielectric loss(tan ${\delta}$) of 0.032 at the frequency range from 1 to 100 KHz. The grain size of $ErMnO_3$ thin film post-annealed at 800 for 1 h was 10∼30 nm. The remanent polarization($P_r$) of the $ErMnO_3$ thin films increased with increasing (001) preferred orientation. The $ErMnO_3$ thin films post-annealed at 800$^{\circ}C$ for 1 h showed the remanent polarization($P_r$) of 400 nC/$cm^2$, with the increase of post-annealing time at 800$^{\circ}C$, the coercive field($E_c$) of thin films was lowered because the dense and homogeneous thin films were obtained.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.4
• /
• pp.210-214
• /
• 2016

We investigated the sintering behavior and piezoelectric properties of lead-free $(K_{0.5}Na_{0.5})NbO_3$ ceramics co-doped with excess 0.01 mol ZnO and x mol $MnO_2$, where x was varied from 0 to 0.03. Excess $MnO_2$ addition was found to retard the grain growth and densification during sintering. However, 0.005 mol $MnO_2$ addition improved the piezoelectric properties of 0.01 mol ZnO added $(K_{0.5}Na_{0.5})NbO_3$ ceramics. The planar mode piezoelectric coupling coefficient, electromechanical quality factor, and piezoelectric constant $d_{33}$ of 0.01 mol ZnO and 0.005 mol $MnO_2$ added specimen were 0.40, 304, and 214 pC/N, respectively.

• Journal of the Korean Ceramic Society
• /
• v.44 no.1 s.296
• /
• pp.52-57
• /
• 2007

We synthesized $(La_{1-x}Sr_x)MnO_3$ as a cathode for SOFC by glycine nitrate process (GNP) and knew the different properties of $(La_{1-x}Sr_x)MnO_3$ by using nitrate solution and oxide solution as a starting material. In case of using nitrate solution as a starting material, main crystal phase peak of $LaMnO_3$ increased as Sr content added up and a peak of $Sr_2MnO_4\;and\;La_2O_3$ was showed as a secondary phase. We added Mn excess to control a crystal phase. In this case, the electrical conductivity had a high value 210.3 S/cm at $700^{\circ}C$. On the other side, when we used oxide solution as a starting material, we found main crystal phase of $LaMnO_3$ to increase as Sr content added up and a peak of $La_2O_3$ as a secondary phase. Similary, we added Mn excess to control a crystal phase in this case. We knew $(La,Sr)MnO_3$ powder to sinter well and the electrical conductivity of the sintered body at $1200^{\circ}C$ for 4 h was 152.7 S/cm at $700^{\circ}C$. The sintered $(La,Sr)MnO_3$ powder at $1000^{\circ}C$ for 4 h got the deoxidization peak, depending on the temperature and in case of using nitrate solution as a starting material, the deoxidization peak was showed at $450^{\circ}C$ which is lower than used a oxide solution as a starting material. As a result, when $(La,Sr)MnO_3$ powder was synthesized to add Mn excess and to use nitrate solution as a starting material, we found it to have the higher deoxidization property and considered it as a cathode for SOFC properly. And we found it to have different electrical conductivity the synthesized $(La,Sr)MnO_3$ powder by using different starting materials like nitrate solution and oxide solution which influence a sintering density and crystal phase.

• Korean Chemical Engineering Research
• /
• v.49 no.5
• /
• pp.633-638
• /
• 2011

Mn substituted La, Sr or Ba-hexaaluminate were prepared by $(NH_4)_2CO_3$ co-precipitate method and calcined at $1,200^{\circ}C$ for 5 h. Catalysts were characterized by X-ray diffraction and $N_2$ physisorption and scanning electron microscope (SEM). Compared to $SrMnAl_{11}O_{19}$ and $BaMnAl_{11}O_{19}$, $LaMnAl_{11}O_{19}$ in which La located at mirror plane showed better crystallinity and high surface area, 13 $m^2/g$. $LaMnAl_{11}O_{19}$ revealed well developed plate-like structure which is characteristic structure of hexaaluminate. The catalytic activity of methane combustion increased in the following order: $LaMnAl_{11}O_{19}$ > $SrMnAl_{11}O_{19}$ > $BaMnAl_{11}O_{19}$ and was dependent on surface area of catalysts. 60 wt% $CeO_2/LaMnAl_{11}O_{19}$ calcined at $700^{\circ}C$ showed enhanced methane activity and methane was oxidized completely at low temperature ($700^{\circ}C$). It was confirmed that addition of ceria seems to be effective for the low and middle temperature combustion of methane. But, after calcination at high temperature of $1,200^{\circ}C$, it lost the promoting effect of ceria due to increase of ceria particle size and it had a limit to applying to the high temperature catalytic combustion.