• Proceedings of the KIEE Conference
• /
• 1998.07g
• /
• pp.2544-2546
• /
• 1998

The electrical and physical charateristics of Pt-Co alloy thin films on $Al_2O_3$ substrate, deposited by r.f cosputtering respectively, were analyzed with thickness of thin films ($1700{\sim}10000{\AA}$) and increasing annealing temperature ($800{\sim}1000^{\circ}C$). At input power of Pt : 4.4 W/$cm^2$, Co : 6.91 W/$cm^2$, working vacuum of 10 mTorr and annealing conditions of $1000^{\circ}C$) and 60 min, the resistivity and sheet resistivity of Pt-Co thin films with thickness of $3000{\AA}$ was $15{\mu}{\Omega}{\cdot}cm$ and 0.5 ${\Omega}/{\square}$, respectively. The TCR value of Pt-Co alloy thin films was measured with various thickness of thin films and annealing conditions. The optimum TCR value of 3850 ppm/$^{\circ}C$ in temperature range($200{\sim}400^{\circ}C$) is gained under conditions $3000{\AA}$ of thin films thickness and $1000^{\circ}C$ of annealing temperature. The thermal charateristics of Pt-Co micro heaters were analysed with Pt-Co RTD integrated on the same substrate. In the analysis of characteristics of Pt-Co micro heaters, the Pt-Co micro heaters with thickness of $3000{\AA}$ and annealing temperature of $1000^{\circ}C$ had a good linearity and temperature is up to $468.2^{\circ}C$ with 2.1 watts of the heating power.

• Ocean Science Journal
• /
• v.43 no.4
• /
• pp.183-193
• /
• 2008

Oncaea venusta Philippi, 1843 has been known as having some different size groups, but recent genetic study for cyt b and ITS 1 (Elvers et al. 2006) suggests that these size groups can be considered as different species. Of these size groups, the largest O. venusta Philippi and the smallest O. venella Farran, 1929 were first described in Korean waters. The latter is easily distinguishable from the former in the following characteristics in addition to its small size: (1) length to width ratio of genital double somite of two genders smaller, and (2) female second pediger bearing inconspicuous dorso-posterior swelling. Oncaea venusta and O. venella co-occur in Korean waters during spring to fall, but their occurrence patterns seasonally differ: the former shows higher density in fall while the latter does in summer.

• Clean Technology
• /
• v.18 no.2
• /
• pp.216-220
• /
• 2012

The objective of the present study was to evaluate catalytic performance of a commercial catalyst (Co/$ZrO_2-Al_2O_3$) for the decomposition of perfluorinated chemicals in a pilot scale reactor containing 30 L of catalysts. At a reaction condition of GHSV $1,800h^{-1}$, $T_{95}$ of $SF_6$ was increased from 580 to $610^{\circ}C$ with increasing of $SF_6$ concentration from 1,000 to 10,000 ppm. $T_{95}$ of $SF_6$ in catalytic decomposition was much smaller than that of thermal decomposition ($1,600^{\circ}C$). The 99% conversion of $SF_6$ was maintained for 72 hours a reaction temperature of $650^{\circ}C$. In order to maintain the $SF_6$ conversion more than 99%, it is necessary to operate at a reaction condition of GHSV less than $2,000h^{-1}$. An operating temperature of $710^{\circ}C$ was required to achieve >95% destruction of the $CF_4$, which was much higher than that of catalytic decomposition of $SF_6$.

• Journal of the Korean Ceramic Society
• /
• v.29 no.3
• /
• pp.232-240
• /
• 1992

Densification behavior, microstructural evolution, and mechanical properties of hot-pressed specimens using $\beta$-SiC and $\alpha$-SiC powder with Al2O3 additive were studied. Beta-SiC powder was fully densified as 205$0^{\circ}C$, but $\alpha$-SiC powder was at 210$0^{\circ}C$. The maximum flexural strength and the fracture toughness of the specimen hot-pressed using $\beta$-SiC powder were 681 MPa and 6.7 MPa{{{{ SQRT {m } }}, and thosevalues of specimen hot-pressed using $\alpha$-SiC powder were 452 MPa and 4.7 MPa{{{{ SQRT {m } }}, respectively. The strength superiority of specimen hot-pressed using $\beta$-SiC powder was due to the finer grain size, and higher density. The higher toughness of specimen hot-pressed using $\beta$-SiC powder than $\alpha$-SiC powder than $\alpha$-SiC powder was due to the crack deflection mechanism arised from the difference of thermal expansion coefficient between $\alpha$ and $\beta$-SiC phases which were co-existed in the sintered body.

• Applied Chemistry for Engineering
• /
• v.9 no.1
• /
• pp.115-120
• /
• 1998

The surface chemistry of $Re_2(CO)_{10}$ deposition for preparing highly dispersed rhenium catalysts and the formation of active site for the metathesis were studied. Alumina as support was treated at 1223K(DA) and 773k(PDA), respectively. The metathesis activity of the catalysts at 298K was measured by using pure propene under atmospheric pressure. The oxidation number of rhenium on PDA was very high, and that on DA was zero-valent with highly dispersed state. The prepared Re/DA catalyst was easily activated by treating with oxygen gas at low temperatures after thermal decomposition at high temperatures. The activity of Re/DA catalyst, even with very low rhenium loading, was much higher than that of Re/PDA or conventional $Re_2O_7/Al_2O_3$ catalysts. Therefore, rhenium carbonyl was effective for preparing a highy active metathesis catalyst with very low rhenium loading. Rhenium ion on Re/DA catalyst seemed to be bonded to two oxygen atoms on DA surface, that is, two-valent. The two-valent rhenium ion was changed to about six-valent by treating with oxygen. It could be considered that propene metathesis occurred through carbene complex which was formed on the six-valent rhenium ions.

• Journal of the Korean Ceramic Society
• /
• v.46 no.5
• /
• pp.493-496
• /
• 2009

Phase stabilized leucite, which has high coefficient of thermal expansion, was synthesized, and its thermal expansion behavior was investigated. The homogeneous leucite phase was synthesized by solid state reaction from the mixture of $K_2CO_3-Al_2O_3-SiO_2$. and its stabilization from tetragonal to cubic phase was attempted by adding $Cs_2CO_3$ into starting materials. And fine powder with an average particle size of a few hundreds ${\mu}m$ were fabricated by planetary milling. During milling, amorphization of leucite was observed and recrystallized after heat treatment. The thermal expansion behavior of tetragonal and cubic leucite has measured and discussed. The average coefficient of thermal expansion of tetragonal and cubic phase leucite from room temperature to $750^{\circ}C$ was $21.4{\times}10^{-6}/^{\circ}C$ and $14.5{\times}10^{-6}/^{\circ}C$, respectively.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.7
• /
• pp.557-564
• /
• 2009

The objective of this study is to efficiently recover phosphorus contained in sewage sludge by a struvite-forming method. The performances were evaluated under various operating conditions(elution with the kind of acid, Mg-compound and temperature) in order to reach the optimum conditions of struvite-forming. As a result, as an elution solution, the elution efficiency of $H_2SO_4$ was 2.65 times higher than that of HCl. Also, the precipitation efficiency of struvite was the highest (97.4%) in case of using $MgCl_2{\cdot}6H_2O$ as Mg-compounds at $25^{\circ}C$. However, the side reaction by Fe, Al and Zn appeared in process of phosphorus recovery. To solve some problems caused by side reacton, large quantities of co-precipitation materials produced by side reaction were removed by precipitating phosphorus compounds in pH 7. Consequently, the recovery efficiency of phosphorus by a struviteforming method was 82.99%, and purity of the recovered struvite product was high.

• Journal of the Korean Chemical Society
• /
• v.55 no.3
• /
• pp.418-429
• /
• 2011

Novel chromium(III), manganese(II), iron(III), cobalt(II), nickel(II), copper(II), ruthenium(III), and zirconyl(II) complexes of $N^1,N^2$-bis(3-((3-hydroxynaphthalen-2-yl)methylene-amino)propyl)phthalamide ($H_4L$, 1) have been synthesized and characterized by elemental, physical, and spectral analyses. The spectral data showed that the ligand behaves as either neutral tridentate ligand as in complexes 2-5 with the general formula $[H_4LMX_2(H_2O)]{\cdot}nH_2O$ (M=Cu(II), Ni(II), Co(II), X = Cl or $NO_3$), neutral hexadentate ligand as in complexes 10-12 with the general formula $[H_4LM_2Cl_6]{\cdot}nH_2O$ (M=Fe(III), Cr(III) or Ru(III)), or dibasic hexadentate ligand as in complexes 6-9 with the general formula $[H_2LM_2Cl_2(H_2O)_4]{\cdot}nH_2O$ (M = Cu(II), Ni(II), Co(II) or Mn(II), and 13 with general formula $[H_4L(ZrO)_2Cl_2]{\cdot}8H_2O$. Molar conductance in DMF solution indicated the non-ionic nature of the complexes. The ESR spectra of solid copper(II) complexes 2, 5, and 6 showed $g_{\parallel}$ >g> $g_e$, indicating distorted octahedral structure and the presence of the unpaired electron in the $N^1,N^2$ orbital with significant covalent bond character. For the dimeric copper(II) complex $[H_2LCu_2Cl_2(H_2O)_4]{\cdot}3H_2O$ (6), the distance between the two copper centers was calculated using field zero splitting parameter for the parallel component that was estimated from the ESR spectrum. The antibacterial and antifungal activities of the compounds showed that, some of metal complexes exhibited a greater inhibitory effect than standard drug as tetracycline (bacteria) and Amphotricene B (fungi).

• Korean Journal of Materials Research
• /
• v.3 no.2
• /
• pp.175-184
• /
• 1993

Abstract Co-and/or AI-added Nd-Fe-B-based magnetic alloys were fabricated by using vacuum induction melting frunace, and melt-spun ribbons were made of the magnetic alloys with single roll rapid quenching method. The variation of magnetic properties of the melt-spun ribbons as a function of Cuwheel velocity (Vs) were investigated. Bonded magnets were made of the optimally quenched ribbon fragments, and the magnetic properties of the melt-spun ribbons and the bonded magnets were studied, relating to the microstructure and crystalline structure. Cu-wheel surface velocity had a strong effect on the magnetic properties of the melt-spun ribbons, and the maximum properties were obtained around Vs =20m/sec. The optimally quenched ribbon had a cellura-type microstructure, in which fine N$d_2$F$e_14$B grains were surrounded by thin Nd-rich phase. In case of a 2.1at% AI-added melt-spun ribbon, the magnetic properties were as follows: iHc, Br, and (BH)max were 15.5KOe, 7.8KG and 8.5MGOe respectively. And resin bonded magnets were fabricated by mixing optimally quenched ribbon fragments with 2.5wt % polyamide resin, compacting and binding at room temperature. The iHc, Br and (BH)max of bonded magnet were lO.2KOe, 4.4KG and 3.3MGOe respectively. And hot-pressed magnets were made by pressing the overquenched ribbons at high temperature. The magnetic properties of hot-pressed magnets were better than those of bonded magnets, and when the holding time was 8 minutes, the iHc, Br, and (BH)max of the hot-pressed magnet were 1O.8KOe, 7.3KG and 8.0MGOe respectively. Domain structure was mainly maze pattern, which means that the easy magnetization axis could be aligned, and the domain width of the hot-pressed magnets was smaller than that of bonded magnets.

• Asian Journal of Atmospheric Environment
• /
• v.6 no.2
• /
• pp.83-95
• /
• 2012

China has been a top producer and exporter of refined lead products in the world since the year 2000. After the phasing-out of leaded gasoline in the late 1990s, non-ferrous metallurgy and coal combustion have been identified as potential major sources of aerosol lead in China. This paper presents the single particle analytical results of ambient aerosol particles collected near a lead smelter using a scanning electron microscopy- energy dispersive x-ray spectroscopy (SEM-EDX). Aerosol particle samples were collected over a 24-hour period, starting from 8 pm on 31 May 2002, using a high volume TSP sampler. For this near source sample, 73 particles among 377 particles analyzed (accounting for 19.4%) were lead-containing particles mixed with other species (S, Cl, K, Ca, and/or C), which probably appeared to be from a nearby lead smelter. Lead-containing particles of less than $2{\mu}m$ size in the near source sample were most frequently encountered with the relative abundances of 42%. SEM-EDX analysis of individual standard particles, such as PbO, PbS, $PbSO_4$, $PbCl_2$, and $PbCO_3$, was also performed to assist in the clear identification of lead-containing aerosol particles. Lead-containing particles were frequently associated with arsenic and zinc, indicating that the smelter had emitted those species during the non-ferrous metallurgical process. The frequently encountered particles following the lead-containing particles were mineral dust particles, such as aluminosilicates (denoted as AlSi), $SiO_2$, and $CaCO_3$. Nitrate- and sulfate-containing particles were encountered frequently in $2-4{\mu}m$ size range, and existed mostly in the forms of $Ca(NO_3,SO_4)/C$, $(Mg,Ca)SO_4/C$, and $AlSi+(NO_3,SO_4)$. Particles containing metals (e.g., Fe, Cu, and As) in this near source sample had relative abundances of approximately 10%. Although the airborne particles collected near the lead smelter contained elevated levels of lead, other types of particles, such as $CaCO_3$-containing, carbonaceous, metal-containing, nitrates, sulfates, and fly-ash particles, showed the unique signatures of samples influenced by emissions from the lead smelter.