• 한국재료학회지
• /
• 제7권10호
• /
• pp.856-862
• /
• 1997

박막형 CdTe/CdS 태양전지의 배면전극(back contacts)물질로서 Cu도핑된 ZnTe 박막(ZnTe:Cu)을 전착법(electroplating)으로 제조하는 연구를 수행하였다. Sulfate계의 전해질 수용액에서 CdTe 기판과 투명전극으로 코팅된 유리(In$_{2}$O$_{3}$: Sn, ITO)기판 위에 ZnTe 박막을 코팅하는 방법으로써 potentiostat와 기판(cathode), Pt counter electrode, Ag/AgCI 표준전극으로 구성된 장치를 사용하여 pH=2.5-4, T=70-8$0^{\circ}C$, 0.02M $Zn^{2+}$ 1x$10^{-4}$M TeO$_{2}$, 0.2M $K_{2}$SO$_{4}$조건에서 -0.800 Vs~-0.975 V 범위의 전압(V$_{a}$ )에 걸쳐 실험하였다. ITO박막을 기판으로 사용하여 cyclic voltammogram을 작성한 결과 약 -0.50 V 에서 Te환원 peak이 나타났다. Auger electron spectroscopy (AES)로 조성분석한 결과 표면에서 Zn signal이 강하게 나왔고 시편의 두께에 따라 Zn의 signal감소하는 반면 Cd signal은 증가하는 것이 확인되었다. SEM 사진으로부터 ZnTe의 표면이 작은 입자 (0.2$\mu\textrm{m}$ 이하)로 구성되어 있으며 낮은 V$_{a}$ 에서는 입자가 작아지면서 조직이 치밀해짐이 관찰되었다. Optical transmission방법에 의하여 ITO기판위에 입혀진 박막의 밴드갭은 2.5 eV으로 측정되었다. 수용액중의 Cu$_{2+}$와 triethanolamine(TEA)은 산성용액에서 착물형성이 이루어지지 않았으며 1,10-phenanthroline과는 pH=2에서도 착물이 형성되었다.

• Journal of Radiation Protection and Research
• /
• 제47권1호
• /
• pp.39-49
• /
• 2022

Background: For proper monitoring of the eye lens dose, an appropriate calibration factor of a dosimeter and information about the mean energies of X-rays are indispensable. The scattered X-ray energy spectra should be well characterized in medical practices where eye lenses of medical staffs might be high. Materials and Methods: Scattered X-ray energy spectra were experimentally derived for three different types of X-ray diagnostic and therapeutic equipment, i.e., the computed tomography (CT) scan, the angiography and the fluoroscopy. A commercially available CdZnTe (CZT) spectrometer with a lead collimator was employed for the measurement of scattered X-rays, which was performed in the usual manner. Results and Discussion: From the obtained energy spectra, the mean energies of the scattered X-rays lied between 40 and 60 keV. This also agreed with that obtained by the conventional half value layer method. Conclusion: The scattered X-rays to which medical workers may be exposed in the region around the eyes were characterized by means of spectrometry. The obtained mean energies of the scattered X-rays were found to match the flat region of the dosimeter response.

• 한국재료학회지
• /
• 제32권11호
• /
• pp.481-488
• /
• 2022

The Cu₂ZnSn(S_xSe_1-x)₄ (CZTSSe) absorbers are promising thin film solar cells (TFSCs) materials, to replace existing Cu(In,Ga)Se₂ (CIGS) and CdTe photovoltaic technology. However, the best reported efficiency for a CZTSSe device, of 13.6 %, is still too low for commercial use. Recently, partially replacing the Zn²⁺ element with a Cd²⁺element has attracting attention as one of the promising strategies for improving the photovoltaic characteristics of the CZTSSe TFSCs. Cd²⁺ elements are known to improve the grain size of the CZTSSe absorber thin films and improve optoelectronic properties by suppressing potential defects, causing short-circuit current (J_sc) loss. In this study, the structural, compositional, and morphological characteristics of CZTSSe and CZCTSSe thin films were investigated using X-ray diffraction (XRD), X-ray fluorescence spectrometer (XRF), and Field-emission scanning electron microscopy (FE-SEM), respectively. The FE-SEM images revealed that the grain size improved with increasing Cd²⁺ alloying in the CZTSSe thin films. Moreover, there was a slight decrease in small grain distribution as well as voids near the CZTSSe/Mo interface after Cd²⁺ alloying. The solar cells prepared using the most promising CZTSSe absorber thin films with Cd²⁺ alloying (8 min. 30 sec.) exhibited a power conversion efficiency (PCE) of 9.33 %, J_sc of 34.0 mA/cm², and fill factor (FF) of 62.7 %, respectively.

• 한국재료학회지
• /
• 제22권5호
• /
• pp.259-273
• /
• 2012

Chalcogenide-based semiconductors, such as $CuInSe_2$, $CuGaSe_2$, Cu(In,Ga)$Se_2$ (CIGS), and CdTe have attracted considerable interest as efficient materials in thin film solar cells (TFSCs). Currently, CIGS and CdTe TFSCs have demonstrated the highest power conversion efficiency (PCE) of over 11% in module production. However, commercialized CIGS and CdTe TFSCs have some limitations due to the scarcity of In, Ga, and Te and the environmental issues associated with Cd and Se. Recently, kesterite CZTS, which is one of the In- and Ga- free absorber materials, has been attracted considerable attention as a new candidate for use as an absorber material in thin film solar cells. The CZTS-based absorber material has outstanding characteristics such as band gap energy of 1.0 eV to 1.5 eV, high absorption coefficient on the order of $10^4cm^{-1}$, and high theoretical conversion efficiency of 32.2% in thin film solar cells. Despite these promising characteristics, research into CZTS-based thin film solar cells is still incomprehensive and related reports are quite few compared to those for CIGS thin film solar cells, which show high efficiency of over 20%. The recent development of kesterite-based CZTS thin film solar cells is summarized in this work. The new challenges for enhanced performance in CZTS thin films are examined and prospective issues are addressed as well.

• 한국의학물리학회:학술대회논문집
• /
• 한국의학물리학회 2002년도 Proceedings
• /
• pp.379-381
• /
• 2002

A single CdZnTe detector is tested for suitability in a prototype CT/ SPECT system designed to acquire both emission and transmission data. The detector has the size of 1${\times}$l-cm$^2$ with 4${\times}$4 1.5${\times}$l.5mm$^2$ pixellated anodes. Since the detector is smaller than imaged object, we translated it in an arc centered at the x-ray tube to image larger objects. Pulse counting electronics with very short shaping time (50 ns) are used to satisfy high photon rates in x-ray imaging, and response linearity up to 3${\times}$10$\^$5/ counts per second per detector element is achieved. The energy resolution of 122-keV gamma-ray is measured to be 14%. We have characterized the system performance by scanning a radiographic resolution phantom .and the Hoffman brain phantom. The spatial resolution of CT and SPECT are about 1 mm and 7 mm, respectively.

• 대한방사선기술학회지:방사선기술과학
• /
• 제39권1호
• /
• pp.35-42
• /
• 2016

CdZnTe(CZT)는 상온에서 동작 가능한 II-VI족 기반의 화합반도체로 CT (Computed Tomography)나 맘모그라피 (mammography)용 검출기로 적용하면, 환자의 피폭선량을 저감할 수 있는 획기적인 소자재료이다. 픽셀(pixel)과 픽셀 피치(pixel pitch)에 따라 X선 변환효율과 신호 교차 (cross-talk)에 영향을 주어 영상 품질이 결정된다. 가중 퍼텐셜 (weighting potential)은 전극의 위치와 형태에 의해서 결정지어지는 가상 퍼텐셜로 Poisson's 방정식의 해를 통해서 구할 수 있다. 본 연구에서는 컴퓨터 기반의 모의실험을 통해 가상 퍼텐셜을 계산하고, 전하유도효율(CIE; charge induction efficiency)과 신호교차를 고려하여 CT용 센서에 적합한 픽셀을 결정하고자 하였다. 모의실험에서 1 mm의 픽셀피치와 2 mm 두께의 CZT를 가정하여, 다양한 픽셀과 픽셀피치를 설정 후 가중 퍼텐셜을 계산하였다. 픽셀의 크기가 $750{\mu}m$이고 픽셀간의 간격이 $250{\mu}m$일 때 최대 전하유도 효율과 최소 신호교차를 나타내었다.

• 한국지구과학회지
• /
• 제22권3호
• /
• pp.208-222
• /
• 2001

이 연구는 전남 광양광산과 그 주변의 하천에 형성되어 있는 부유성 비정질 퇴적물의 지구화학적 특성을 밝히기 위해 수행되었다. 부유성 비정질 퇴적물의 주요성분은 Fe$_2$O$_3$이며, Fe$_2$O$_3$의 함량은 17.9${\cdot}$72.3wt.% 범위로 나타난다. Fe함량이 증가하면 Si, Al, Mg, Na, K, Mn 및 Ti 함량이 감소하며 Te, Au, Ga, Bi, Cd, Hg, Sb, 및 Se등의 함량은 증가한다. 하상 침전물인 비정질 퇴적물에는 As(최대 54.9ppm), Bi(최대 3.77ppm), Cd(최대 3.65ppm), Hg(최대64ppm), Sb(최대 10.1ppm), Cu (최대 37.1ppm), Mo(최대 8.86ppm), Pb(최대 9.45ppm) 및 Zn(최대 29.7ppm) 등의 중금속원소가 농집되어 있다. 황갈색 침전물에는 Au(최대 4.40ppm)와 Ag(최대 0.24ppm) 함량이 매우 높게 나타나며, Au함량은 하천의 상류지역에 높은 함량을 보이다가 하류지역으로 갈수록 그 함량이 감소한다. 반면에 Ag 함량은 상류지역의 하천에 낮은 함량을 보이다가 하류지역으로 갈수록 그 함량이 증가하여 나타난다. XRD분석에서 하상의 황갈색 침전물은 X-선회절선이 뚜렷하지 않은 비정질이거나 결정도가 미약한 철수산화물로 밝혀졌으며, 석영, 침철석, 고령토, 일라이트 등이 관찰된다. IR분석에서 비정질 하상 퇴적물은 OH기, H$_2$O, SO$_4$ 및 Fe-O 기에 의한 흡수밴드가 관찰된다.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 추계학술발표대회
• /
• pp.35.1-35.1
• /
• 2011

New photovoltaic (PV) materials and manufacturing approaches are needed for meeting the demand for lower-cost solar cells. The prototypal thin-film photovoltaic absorbers (CdTe and $Cu(In,Ga)Se_2$) can achieve solar conversion efficiencies of up to 20% and are now commercially available, but the presence of toxic (Cd,Se) and expensive elemental components (In, Te) is a real issue as the demand for photovoltaics rapidly increases. To overcome these limitations, there has been substantial interest in developing viable alternative materials, such as $Cu_2ZnSnS_4$ (CZTS) is an emerging solar absorber that is structurally similar to CIGS, but contains only earth abundant, non-toxic elements and has a near optimal direct band gap energy of 1.4~1.6 ev and a large absorption coefficient of ${\sim}10^4\;cm^{-1}$. The CZTS absorber layers are grown and investigated by various fabrication methods, such as thermal evaporation, e-beam evaporation with a post sulfurization, sputtering, non-vacuum sol-gel, pulsed laser, spray-pyrolysis method and electrodeposition technique. In the present work, we report an alternative method for large area deposition of CZTS thin films that is potentially high throughput and inexpensive when used to produce monolithically integrated solar panel modules. Specifically, we have developed an aqueous chemical approach based on chemical bath deposition (CBD) with a subsequent sulfurization heat treatment. Samples produced by our method were analyzed by scanning electron microscopy, X-ray diffraction, transmission electron microscopy, absorbance and photoluminescence. The results show that this inexpensive and relatively benign process produces thin films of CZTS exhibiting uniform composition, kesterite crystal structure, and good optical properties. A preliminary solar cell device was fabricated to demonstrate rectifying and photovoltaic behavior.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2012년도 춘계학술발표대회
• /
• pp.99.1-99.1
• /
• 2012

The thin-film photovoltaic absorbers (CdTe and $Cu(In,Ga)Se_2$) can achieve solar conversion efficiencies of up to 20% and are now commercially available, but the presence of toxic (Cd,Se) and expensive elemental components (In, Te) is a real issue as the demand for photovoltaics rapidly increases. To overcome these limitations, there has been substantial interest in developing viable alternative materials, such as $Cu_2ZnSnS_4$ (CZTS) is an emerging solar absorber that is structurally similar to CIGS, but contains only earth abundant, non-toxic elements and has a near optimal direct band gap energy of 1.4 - 1.6 eV and a large absorption coefficient of ~104 $cm^{-1}$. The CZTS absorber layers are grown and investigated by various fabrication methods, such as thermal evaporation, e-beam evaporation with a post sulfurization, sputtering, non-vacuum sol-gel, pulsed laser, spray-pyrolysis method and electrodeposition technique. In the present work, we report an alternative aqueous chemical approach based on chemical bath deposition (CBD) method for large area deposition of CZTS thin films. Samples produced by our method were analyzed by scanning electron microscopy, X-ray diffraction, transmission electron microscopy, absorbance and photoluminescence. The results show that this inexpensive and relatively benign process produces thin films of CZTS exhibiting uniform composition, kesterite crystal structure, and some factors like triethanolamine, ammonia, temperature which strongly affect on the morphology of CZTS film.

• 한국의학물리학회지:의학물리
• /
• 제13권4호
• /
• pp.229-233
• /
• 2002

CdZnTe 검출기를 제작하고 CT/SPECT 조합영상 시스템에 설치하여 엑스선 및 감마선검출기로서의 응용가능성을 타진해 보았다. 검출기의 크기는 10$\times$10$\times$5 ㎣ 이었다. 양극은 4$\times$4 픽셀로 설계하였으며 각 픽셀의 크기는 $1.5\times$l.5 $\textrm{mm}^2$ 이었다. 음극은 Au로 전극을 만들어 주었다. 시스템의 성능을 조사하기 위해서 방사선촬영용 분해능팬텀과 호프만 뇌 팬텀을 사용하였다. X선 영상에서 고광자방출율을 만족시키기 위해서 shapping time은 50ns 로 하었으며, 3$\times$$10^{5}$ counts/s 까지 선형성이 유지되었다. Tc-99m의 140 keV 감마선에 대한 에너지 분해능은 50 ㎱와 2 $\mu\textrm{s}$ shaping time을 걸어주었을 때 각각 10.4%와 5.3%이었다. CT와 SPECT의 공간분해능은 각각 1 mm와 9 mm 이었다. 광피이크 효율은 50 ㎱와 2 $\mu\textrm{s}$일 때 각각 41.0%와 72.5%이었다.