• Transactions of the Korean hydrogen and new energy society
• /
• v.23 no.3
• /
• pp.227-235
• /
• 2012

Finding an alternative fuel and reducing environmental pollution are the main goals for future internal combustion engines. The purpose of this study is to obtain low-emission and high-efficiency by hydrogen enriched LPG fuel in constant volume chamber. An experimental study was carried out to obtain fundamental data for the combustion and emission characteristics of pre-mixed hydrogen and LPG in a constant volume chamber (CVC) with various fractions of hydrogen-LPG blends. To maintain equal heating value of fuel blend, the amount of LPG was decreased as hydrogen was gradually added. Exhaust emissions were measured using a HORIBA exhaust gas analyzer for various fractions of hydrogen-LPG blends. The results showed that the rapid combustion duration was shortened, and the rate of heat release elevated as the hydrogen fraction in the fuel blend was increased. Moreover, the maximum rate of pressure rise also increased. These phenomena were attributed to the burning velocity which increased exponentially with the increased hydrogen fraction in the $H_2$-LPG fuel blend. Exhaust HC and $CO_2$ concentrations decreased, while NOX emission increased with an increase in the hydrogen fraction in the fuel blend. Our results could facilitate the application of hydrogen and LPG as a fuel in the current fossil hydrocarbon-based economy and the strict emission regulations in internal combustion engines.

• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.6
• /
• pp.524-534
• /
• 2013

Gasoline direct injection(GDI) engine has a high thermal efficiency, but it has a problem to increase carbon emissions such as soot and $CO_x$. In this study, the objective is to analyze numerically a problem for adding the hydrogen during the intake stroke so as to reduce the injected amount of gasoline in GDI engines. For selection of the base model, the cylinder pressure of simulation is matched to experimental data. The numerical analysis are carried out by a CFD model with the hydrogen addition of 2%, 3% and 4% on the volume basis. In the case of 3% hydrogen addition, the injected gasoline amount is only changed to match the maximum pressure of simulation to that of the base model for additional study. It is found that the combustion temperature and pressure increase with the hydrogen addition. And NO emission also increases because of the higher combustion temperature. $CO_x$ emissions, however, are reduced due to the decrease of injected gasoline amount. Also, as the injected gasoline amount is reduced for the same hydrogen addition ratio, the gross indicated work is no significant, But NO and $CO_x$ emissions are considerably decreased. On the order hand, $CO_x$ emissions of two cases are more decreased and their gross indicated works are higher obtained than those of the base model.

• Journal of Korean Society of Forest Science
• /
• v.100 no.4
• /
• pp.708-714
• /
• 2011

Wood store carbon that the forest absorbed until burned or decomposed over a long period. Such materials are most used in houses except in paper and pulp, and the use of wood in houses play an important role in reducing green-house gases. Therefore, we estimated the amount of carbon stocks in Korean houses, and analyzed how much contribution such stocks offers to green-house gas reduction. As the result, the carbon stocks amount of the wood products in Korean houses was 28.4 million $tCO_2$, which is 4.6% of the total annual green-house gas emission in Korea (620 million $tCO_2$ e), and 77.4% of forest sinks (LULUCF). Even though few wooden houses which use most wood in housing exist in Korea, the carbon stocks of wood products in houses in 2010 increased to 4.1 times that in 1975 (21.4 million $tCO_2$) because the carbon stocks increased due to apartment construction, which hit its stride from the last 1980's.

• Journal of the Korea Concrete Institute
• /
• v.27 no.4
• /
• pp.427-434
• /
• 2015

The objective of this study is to establish an rational mixture-proportioning procedure for low-$CO_2$ concrete using supplementary cementitious materials (SCMs) achieving the targeted $CO_2$ reduction ratio as well as the conventional requirements such as initial slump, air content, and 28-day compressive strength of concrete. To evaluate the effect of SCM level on the $CO_2$ emission and compressive strength of concrete, a total of 12537 data sets were compiled from the available literature and ready-mixed concrete plants. The amount of $CO_2$ emission of concrete was assessed under the system boundary from cradle to concrete production stage at a ready-mixed concrete plant. Based on regression analysis using the established database, simple equations were proposed to determine the mixture proportions of concrete such as the type and level of SCMs, water-to-binder ratio, and fine aggregate-to-total aggregate ratio. Furthermore, the $CO_2$ emissions for a given concrete mixture can be straightforwardly calculated using the proposed equations. Overall, the developed mixture-proportioning procedure is practically useful for determining the initial mixture proportions of low-$CO_2$ concrete in the ready-mixed concrete field.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.2
• /
• pp.67-75
• /
• 2014

Biodiesel as alternative fuels has been widely studied due to biodiesel merits such as lower sulfur, lower aromatic hydrocarbon and higher oxygen content. But biodiesels could be easily oxidized by several conditions. In this study, various antioxidants such as propyl gallate, TBHA, TBHQ, DTBHQ, butyl-amin, aniline and pyrogallol were added in the biodiesel produced by the used cooking oil, then the material property test and the vehicle emissions test were conducted in accordance with test method. From the results of material property test, all antioxidants were suitable for the quality standard of density and kinematic viscosity, but Propyl gallate and Pyrogallol, as a type of Gallate additives, showed that the result of TAN increased rapidly according to the increase of the amount of additives. In the oxidation stability test, TBHQ, Butyl-amine and Aniline showed the excellent oxidation stability. Also, when considering the material property test, TBHQ was verified to the most excellent additives. In case of the vehicle emissions test, the testing was conducted by using the biodiesel added by TBHQ and was conducted by using two light duty diesel vehicles suitable for the EURO 4 and EURO 5 emission regulation. The result of testing showed that when the TBHQ was added, the amounts of CO, NOx and NMHC+NOx were decreased but the amount of $CO_2$ was increased.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.3
• /
• pp.110-114
• /
• 2017

$NiO/NiCo_2O_4$ nanocubes were successfully synthesized via the calcination process of $Ni_3[Co(CN)_6]_2$ PBAs. The prepared monodispersed $Ni_3[Co(CN)_6]_2$ PBAs were aggregated by 'self-assembly' of the nuclei generated during the synthesis reaction. The self-assembly rate of the particles is affected by the temperature and the amount of surfactant SDBS (sodium dodecylbenzenesulfonate). FESEM analysis shows that monodispersed 200 nm PBA nanocubes are obtained at 0.25 g SDBS and $60^{\circ}C$ temperature. Thermal behavior was confirmed by thermogravimetric-differential thermal analysis (TG-DTA) to determine optimal calcination conditions. Then, field emission scanning electron microscopy (FESEM) and X-ray diffraction (XRD) analyzes were performed to investigate the morphology and crystallinity of the particles precursors and $NiO/NiCo_2O_4$ nanocubes.

• Korean Journal of Soil Science and Fertilizer
• /
• v.45 no.5
• /
• pp.853-860
• /
• 2012

To estimate potential use of fly ash in reducing $CH_4$ and $CO_2$ emission from soil, $CH_4$ and $CO_2$ fluxes from a paddy soil mixed with fly ash at different rate (w/w; 0, 5, and 10%) in the presence and absence of fertilizer N ($(NH_4)_2SO_4$) addition were investigated in a laboratory incubation for 60 days under changing water regime from wetting to drying via transition. The mean $CH_4$ flux during the entire incubation period ranged from 0.59 to $1.68mg\;CH_4\;m^{-2}day^{-1}$ with a lower rate in the soil treated with N fertilizer due to suppression of $CH_4$ production by $SO_4^{2-}$ that acts as an electron acceptor, leading to decreases in electron availability for methanogen. Fly ash application reduced $CH_4$ flux by 37.5 and 33.0% in soils without and with N addition, respectively, probably due to retardation of $CH_4$ diffusion through soil pores by addition of fine-textured fly ash. In addition, as fly ash has a potential for $CO_2$ removal via carbonation (formation of carbonate precipitates) that decreases $CO_2$ availability that is a substrate for $CO_2$ reduction reaction (one of $CH_4$ generation pathways) is likely to be another mechanisms of $CH_4$ flux reduction by fly ash. Meanwhile, the mean $CO_2$ flux during the entire incubation period was between 0.64 and $0.90g\;CO_2\;m^{-2}day^{-1}$, and that of N treated soil was lower than that without N addition. Because N addition is likely to increase soil respiration, it is not straightforward to explain the results. However, it may be possible that our experiment did not account for the substantial amount of $CO_2$ produced by heterotrophs that were activated by N addition in earlier period than the measurement was initiated. Fly ash application also lowered $CO_2$ flux by up to 20% in the soil mixed with fly ash at 10% through $CO_2$ removal by the carbonation. At the whole picture, fly ash application at 10% decreased global warming potential of emitted $CH_4$ and $CO_2$ by about 20%. Therefore, our results suggest that fly ash application can be a soil management practice to reduce green house gas emission from paddy soils. Further studies under field conditions with rice cultivation are necessary to verify our findings.

• International Journal of Highway Engineering
• /
• v.12 no.3
• /
• pp.103-111
• /
• 2010

Recently, usage bicycle has been encouraged to reduce energy consumption and $CO_2$. For this purpose, lots of bike road construction are planned. Typical type of pavement used in bikeroad such as asphalt concrete pavement, portland cement concrete pavement, colored pavement, soil pavement. However, these pavement types may need high construction cost comparing the required capacity of bike road. In this study, roller compacted concrete pavement which are economical and durable, are investigated to use as bike road pavement. The optimum compaction level and mix design of roller compacted concrete pavement are suggested by exploring strength test with various mixture ratio and compaction level, Also durability was examined based on freeze-thaw and scaling test. In addition, the cost and amount of carbon emission during in the construction of roller compacted concrete were evaluated and compare with the cost and carbon emission of typical portland cement concrete.

• Land and Housing Review
• /
• v.3 no.4
• /
• pp.399-406
• /
• 2012

One-third of total energy and 50% of $CO_2$ emissions arise from construction phase. Because of this global amount of energy consumption and $CO_2$ emission, we must do our best to solve this problem. But our existing ways of meeting this problem has focused on the energy consumption saving of the construction and dwelling stage. On the other hand, we has been treated too lightly for handling the $CO_2$ emissions problem during the maintenance management and the demolition process so far,. In this paper, we quantitatively predicted and evaluated the environmental load in each construction step during all life cycle. And, we developed the environmental load assessment program for each construction step. And we proposed the reliable decision support model for objective and reliable environmental load assessment and reduction. This result must help the development of construction technology and low carbon & green growth.

• Journal of the Semiconductor & Display Technology
• /
• v.10 no.2
• /
• pp.13-17
• /
• 2011

We have developed a new energy-consuming monitoring system that has made it possible to measure the energy consumption of a gas scrubber, one of semiconductor processing equipments, and installed this system to the gas scrubber under operating at a manufacture site. Using this system, we have measured consumptions of electric power and processing gas consumed at standby to operating mode. In case of the gas scrubber, processing gas flows continuously into it at standby and operating mode. Therefore, if the electric power has been supplied, the processing gas can flows into the device for 24 hours. Moreover, at operating of gas scrubber, the amount of electricity consumption is 5 kWh. At Standby of gas scrubber, it spends 3kwh. It is certain that the energy consumption is greater at operating mode than at standby mode. The carbon emission rates from 24 hour gas scrubber operation are 236 $kgCO_2$/day of $N_2$, 57 $kgCO_2$/day of electric power and 0.001 $kgCO_2$/day of cooling water. Most of carbon is emitted from $N_2$ gas and electric power consumption.