• Membrane Journal
• /
• v.5 no.1
• /
• pp.35-43
• /
• 1995

For several years lots of attempts have been made to establish the liquid membrane-based techniques for separations of gas mixtures especially containing carbon dioxide. A more effective system to separate $CO_{2}$ from flue gases, a circulatory hollow-fiber membrane absorber(HFMA) consisting of absorption and desorption modules with vacuum mode, has been considered in this study. Gas-liquid mass transfer has been modeled on a membrane module with non-wetted hollow-fibers in the laminar flow regime. The influence of an absorbent flow rate on the separation performance of the circulatory HFMA can be predicted quantitatively by obtaining the $CO_{2}$ concentration profile in a tube side. The system of $CO_{2}/N_{2}$ binary gas mixture has been studied using pure water as an(inert) absorbent. As the absorbent flow rate is increased, the permeation flux(i.e., defined as permeation rate/membrane contact area) also increases. The enhanced selectivity compared to the previous results, on the other hand, shows the decreasing behavior. It has been found obviously that the permeation flux depends on the variations of pressure in gas phase of desorption module. From an accurate comparison with the results of conventional flat sheet membrane module, the advantageous permeability of this circulatory HFMA can be clearly ascertained as expected. Our efforts to the theoretical model will provide the basic analysis on the circulatory HFMA technique for a better design and process.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1564-1567
• /
• 2009

Cu(In,Ga)$Se_2$ (CIGS) thin films were formed using CIGS bulk by electron-beam evaporation method with an evaporation current from 20 mA to 90 mA. The experimental results showed that the chemical compositions and the properties of CIGS films varied with the different evaporation current. The Cu-rich CIGS film was deposited successfully with a band gap of 1.20 eV when the evaporation current was 90 mA.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.4
• /
• pp.93-99
• /
• 1997

The re quest to develop the engines that are able to run without air or with very little oxygen condition is raised with the interest of ocean science or the mines. This research had already be gun before the world war II, but had been stagnant owing to the appearance of nuclear power. Recycle diesel engines have ability to run under the above mentioned condition the recycle diesel engine recirculates exhaust gases into intake port and consumes additional oxygen supplied by oxygen tank. Carbon dioxide is controlled by the absorber. The combustion and emission characteristics of recycle diesel engines are quite different with conventional one because the working fluids of recycle diesel engines consist of Ar, $CO_2$ and $O_2$ as well as $N_2$. Recycle diesel engine is therefore different with general diesel engine from the viewpoint of intake air composition. It is required to investigate the effect of intake composition in the combustion and emission to know recycle diesel engine. In this study, NOx concentration, smoke and cylinder pressure are measured with the variation of Ar and $CO_2$ Reduces show that the addition of Ar reduces NOx but increases smoke. Otherwise $CO_2$ reduces smoke and NOX simultaneously. Only $CO_2$ increases the ignition delay and both gases increase fuel consumption Ar addition is superior to $CO_2$ addition for the performance of recycle diesel engine system but $CO_2$ has the avantage with respect to emission.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.461.1-461.1
• /
• 2014

본 연구진에서는 기존에 Ag2S 양자점을 흡광층으로 활용하여 양자점 감응형 태양전지(QDSC)를 제작, 그 성능과 특징을 분석하여 발표한 바 있다. 기존 연구에서 제작된 Ag2S QDSC는 11 mA/cm2의 비교적 높은 광전류와 260 mV의 비교적 낮은 전압으로 인해 1.2%의 광전환효율 성능을 나타내는 것으로 보고되었다. 추후 연구로 진행된 본 결과에서는, 기존에 Single absorber로 사용된 Ag2S의 한계를 보완하기 위해 CdS를 도입하여 co-sensitization을 활용하였다. CdS는 약 2.3 eV의 밴드갭 에너지를 갖는 물질로, 1.1 eV의 밴드갭을 갖는 Ag2S에 비해 흡광 영역은 좁지만 그만큼 전자-정공 재결합을 억제할 수 있는 장점을 가지고 있다. 또한, 전도층으로 사용한 n-type 물질인 ZnO 나노선과의 밴드구조가 매우 적합하게 조화되어, ZnO/CdS/Ag2S 순서로 이종구조를 접합시켰을 때 세 물질의 Conduction band level과 Valence band level이 순차적으로 연결되는 cascade-shaped 밴드구조를 이루게 된다. 빛을 받아 Ag2S와 CdS에서 생성된 전자는 이 cascade 모양의 conduction band를 따라 순차적으로 ZnO로 잘 전달되게 되어, 효율 향상에 큰 도움을 주었다. 이런 장점들로 인해, CdS-Ag2S co-sensitized QDSC는 Ag2S QDSC에 비해 2배나 향상된 효율인 2.4%를 기록하였으며, 이는 IPCE spectrum 측정 등으로 근거가 뒷받침되었다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.85-87
• /
• 2009

Despite the success of $Cu(In,Ga)Se_2$ (CIGS) based PV technology now emerging in several industrial initiatives, concerns about the cost of In and Ga are often expressed. It is believed that the cost of those elements will eventually limit the cost reduction of this technology. one candidate to replace CIGS is $Cu_2ZnSnSe_4$ (CZTSe), fabricated by co-evaporation technique. Effects of substrate temperature of $Cu_2ZnSnSe_4$ absorber layer on the performance of thin films solar cells were investigated. As substrate temperature increased, the grain size of $Cu_2ZnSnSe_4$ films increased presumably. At a optimal condition of substrate temperature is $320^{\circ}C$, the solar cell shows a conversion efficiency of 1.79% with $V_{OC}$ of 0.213V, JSC of $16.91mA/cm^2$ and FF of 49.7%.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1997.05b
• /
• pp.171-176
• /
• 1997

UO$_2$-Gd$_2$O$_3$fuel has been sintered to study the effect of powder property and sintering atmospheres on densification and microstructure. Three types of powders have been used; AUC-UO$_2$ powder and ADU-UO$_2$ powder were mixed with Gd$_2$O$_3$ Powder, and co-milled AUC-UO$_2$ and Gd$_2$O$_3$ powder. UO$_2$-(2, 5, 10)wt% Gd$_2$O$_3$pellets have been sintered at 168$0^{\circ}C$ for 4 hours in the mixture of H$_2$ and $CO_2$ gases, of which oxygen potential has been controlled by the ratio of $CO_2$ to H$_2$ gas. Densities of UO$_2$-Gd$_2$O$_3$ fuel pellets are quite dependent on powder types, and UO$_2$-Gd$_2$O$_3$ fuel using co-milled UO$_2$ powder yields the highest density. A long range homogeneity of Gd is determined by powder mixing. As the oxygen potential of sintered atmosphere increases, the sintered densities of UO$_2$-Gd$_2$O$_3$ pellets decrease but grain size increases. In addition, (U, Gd)O$_2$ solid solution becomes more homogeneous. The UO$_2$-Gd$_2$O$_3$fuel having adequate density and homogeneous microstructure can be fabricated by co-milling powder and by high oxygen potential.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.18 no.1_2
• /
• pp.1-8
• /
• 2012

Kimchi, a Korean fermented vegetable is packaged without pasteurization and distributed with live bacteria actively working to produce lactic acid and carbon dioxide gas in the product. The $CO_2$ production consisting of two distinct phases of initial fast and later slow rates depends on kimchi type, salt content and storage temperature. The $CO_2$ produced from kimchi is accumulated in the product package causing volume expansion and pressure buildup. The dependence of $CO_2$ production rate on salt content and storage temperature has been published formerly and can be used for estimating the package volume and pressure under a variety of storage conditions. As methods to alleviate the problems from the produced $CO_2$, package designs with controlled diffusion pinhole, high $CO_2$ permeable film or $CO_2$ absorber have been tried by several researchers. Properly designed packages adopting the device or tool were shown to have high dissolved $CO_2$ in kimchi without volume expansion and pressure buildup, giving good sensory quality with carbonic taste. Advantages and limitations of each method have been discussed.

• Korean Chemical Engineering Research
• /
• v.45 no.3
• /
• pp.258-263
• /
• 2007

Ammonia water was investigated as a new absorbent of the chemical absorption process for the removal of $CO_2$ in flue gas. The suitable range of ammonia water concentration and $CO_2$ loading ($mol\;CO_2/mol\;NH_3$) were decided in the point of view of $CO_2$ absorption capacity and $NH_4HCO_3$ precipitation. The absorption capacity of $CO_2$ and the precipitation of $NH_4HCO_3$ in liquid phase were calculated by the Pitzer model for electrolyte solution. The $CO_2$ absorption capacity of the ammonia water over $5\;molNH_3/kgH_2O$ was higher than that of conventional amine absorbent. The $CO_2$ loadings where precipitation occurred were decided at various absorbent concentrations. Theses values were higher than 0.5 in the concentration range of $5-14\;molNH_3/kgH_2O$ at 293, 313 K. The absorber for the removal of $CO_2$ in flue gas could be operated without $NH_4HCO_3$ precipitation by using high concentration of ammonia water below these $CO_2$ loading values. The optimum temperature of the ammonia water absorbent for removal of $CO_2$ in flue gas was 297-312 K depending on the concentration of ammonia water.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.36.1-36.1
• /
• 2010

While the substrate-type solar cells with Cu(In,Ga)Se2 absorbers yield conversion efficiencies of up 20%[1], the highest published efficiency of Cu(In,Ga)Se2 superstrate solar cell is only 12.8% [2]. The commerciallized Cu(In,Ga)Se2 solar cells are made in the substrate configuration having the stacking sequence of substrate (soda lime glass)/back contact (molybdenum)/absorber layer (Cu(In,Ga)Se2)/buffer layer (cadmium sulfide)/window layer (transparent conductive oxide)/anti reflection layer (MgF2) /grid contact. Thus, it is not possible to illuminate the substrate-type cell through the glass substrate. Rather, it is necessary to illuminate from the opposite side which requires an elaborate transparent encapsulation. In contrast to that, the configuration of superstrate solar cell allows the illumination through the glass substrate. This saves the expensive transparent encapsulation. Usually, the high quality Cu(In,Ga)Se2 absorber requires a high deposition temperature over 550C. Therefore, the front contact should be thermally stable in the temperature range to realize a successful superstrate-type solar cell. In this study, it was tried to make a decent superstrate-type solar cell with the thermally stable ZnO:Al layer obtained by adjusting its deposition parameters in magnetron sputtering process. The effect of deposition condition of the layer on the cell performance will be discussed together with hall measurement results and current-voltage characteristics of the cells.

• Korean Chemical Engineering Research
• /
• v.47 no.6
• /
• pp.795-800
• /
• 2009

In this study, the $CO_2$ removal characteristics of the Vortex tube type absorbtion apparatus were investigated to enhance the compactness of $CO_2$ absorption process and to reduce the amount of absorbing solution of the $CO_2$ separation process. The Vortex tube with the diameter of 17 mm and the length of 250mm was introduced in the experimental apparatus to treat $20Nm^3/hr$ of $CO_2$ containing flue gas. The flue gases for experiments containing 11~13 vol% of $CO_2$ were supplied from the coal-firing CFBC power plant with 12 ton/hr of steam producing capacity. The mixed solutions of 20 wt% of MEA as base solution with the adding solutions like HMDA, AMP and KOH were used as absorbents. The experiments were executed under the various conditions like the absorbing solution concentrations in the range of 20 to 50 wt%, the flow rate of $CO_2$ containing flue gases in the range of 6 to $15Nm^3/hr$ and the flow rate of absorbing solution in the range of 1.0 to 3.0 l/min. As a results, the $CO_2$ removal efficiency of mixed absorbent of 20 wt% of MEA with HMDA was remarkable. From this study, we concluded that the efficient separation of $CO_2$ from flue gases using the features of the Vortex tube type absorbing unit for gas/liquid contact and the separation of gas/liquid be possible. But more works are needed to increase the $CO_2$ removal efficiency of Vortex tube process.