• KSBB Journal
• /
• 제5권4호
• /
• pp.329-334
• /
• 1990

In an attempt to develop a novel process for ethanol production from starch, a simultaneous saccharification and fermentation (SSF) process using Zymomonas mobilis and amyloglucosidase (AMG) was studied in continuous modes. Compared with a conventional cylindrical column type of fermentor, the tapered column type of fermentor was found to be superior in terms of reactor performance for ethanol fermentation. The tapered columm fermentor packed with coimmobilized Z. mobilis and AMG alleviated the problems which were associated with CO2 evolution and provided a significantly better flow pattern for both liquid and gas phases in the fermentor without channelling. However, the fluidized bed type of tapered column fermentor using flocculent strain of Z. mobiles and immobilized AMG showed lower productivity (5.2g/1/h) than that of packed bed type of tapered column fermentor(9.2g/l/h).

• Geomechanics and Engineering
• /
• 제17권2호
• /
• pp.215-225
• /
• 2019

The mechanical behavior of rock is essential to estimate the capacity and long-term stability of $CO_2$ storage in deep saline aquifers. As the depth of reservoir increases, the pressure and temperature that applied on the rock increase. To answer the question of how the confining pressure and temperature influence the mechanical behavior of reservoir rock, triaxial compression experiments were carried out on brine-saturated sandstone at elevated temperature. The triaxial compressive strength of brine-saturated sandstone was observed to decrease with increasing testing temperature, and the temperature weakening effect in strength enhanced with the increase of confining pressure. Sandstone specimens showed single fracture failures under triaxial compression. Three typical regions around the main fracture were identified: fracture band, damaged zone and undamaged zone. A function was proposed to describe the evolution of acoustic emission count under loading. Finally, the mechanism of elevated temperature causing the reduction of strength of brine-saturated sandstone was discussed.

• 천문학회보
• /
• 제44권2호
• /
• pp.77.2-77.2
• /
• 2019

Measurements of supermassive black hole (SMBH) masses are crucial in studying the co-evolution of SMBHs and their host galaxies. Although reverberation mapping is the most accurate method known to date, this requires spectroscopic monitoring over long periods. Thus, the current sample barely reaches three digits. The virial method, on the other hand, uses emission-line and continuum properties from a single spectrum to estimate the SMBH mass; hence the name single-epoch method. The Sloan Digital Sky Survey (SDSS) has observed spectra of almost all quasi-stellar objects (QSOs) discovered so far. Building on previous studies, using the single-epoch method, we estimate the SMBH masses of more than 500,000 QSOs from the SDSS DR14 Quasar Catalog. This increases the mass-estimated SMBH sample almost by a factor of two, and especially more for the low-mass regime, which was the main target of SDSS-IV (eBOSS).

• 한국주조공학회지
• /
• 제12권4호
• /
• pp.305-316
• /
• 1992

Steel and iron castings made with expandable polystylene (referred to hereafter as EPS) patterns are often affected by distinctive defects associated with incomplete decomposition of the EPS as the molds are filled with metal. The effects of practical factors on carbon pick-up were investigated on the specimens, by taking successive layers of swarf and analysis, whereas the lustrous carbon is determined by using combustion analysis. The quality of the castings, with particular reference to carbon pick-up in low carbon steel and lustrous carbon on gray iron, is further influenced to a significant extent by such practical factors as reduced pressure, the pouring temperature, the density of EPS pattern, the additive in coating and in pattern and the casting thickness. The rate at which carbon pick-up and lustrous carbon deposites are formed can be reduced by reducing the density of the pattern and also reducing pressure, especially by adding $Na_2CO_3$ in coating and in pattern to promote $CO_2$ evolution. The upper parts of castings obtained using EPS patterns are slightly higher in carbon pick-up and in lustrous carbon than other parts.

• 한국세라믹학회지
• /
• 제53권1호
• /
• pp.81-86
• /
• 2016

The effect of substrate rotation speed on the phase forming behavior and microstructural variation of 8 wt% yttria ($Y_2O_3$) stabilized $ZrO_2$ (8YSZ) coatings as a thermal barrier coating has been investigated. 8YSZ coatings with $100{\sim}200{\mu}m$ thickness were deposited by electron beam-physical vapor deposition onto a super alloy (Ni-Cr-Co-Al) substrate with a bond coating (NiCo-CrAlY). The width of the columnar grains of the 8YSZ coatings increased with increasing substrate rotation speed from 1 to 30 rpm at a substrate temperature range of $900{\sim}950^{\circ}C$. In spite of the different growth behaviors of coatings with different substrate rotation speeds, the phases of each coating were not changed remarkably. Even after post heat treatments with various conditions of the coated specimens fabricated at 20 rpm, only a change of color was noticeable, without any remarkable change in the phase or microstructure.

• 자원환경지질
• /
• 제30권6호
• /
• pp.519-529
• /
• 1997

Volcanic rocks including rhyolitic tuff, rhyolite and welded tuff in the Bupyeong silver mine area form a topographic circular structure which is interpreted as a resurgent caldera. Granitic rocks are emplaced inside and outside area of the circular structure. Pervasive silver mineralization took place in the rhyolitic rock of the southwestern margin of the caldera. Gas and fluid incluson studies were carried out to investigate the petrogenetic evolution and post-magmatic alteration for the rhyolitic and granitic rocks. Gas compositions are characterized by a low $CH_4/CO_2$ ratio (0.004-0.005) for rhyolitic and inside granitic rocks and a high $CH_4/CO_2$ ratio (0.01~0.29) for outside granitic rocks such as the Kimpo and Incheon granites. Homogenization temperature of solid daughter mineral bearing fluid inclusion (III and IV types) and two phase fluid inclusion (I and II types) for quartz in the Bupyeong granites range from 400 to $500^{\circ}C$ and 121 to $514^{\circ}C$, respectively. Salinties vary from 20 to 30 wt% NaCl for type III and IV inclusions and less than 20 wt % NaCl for type I and II inclusions. The fluid inclusion data shows a considerable influx of the meteoric water toward post magmatic alteration stage.

• 한국재료학회지
• /
• 제27권11호
• /
• pp.583-589
• /
• 2017

Ceramic ink-jet printing has become a widespread technology in ceramic tile and ceramicware industries, due to its capability of manufacturing products on demand with various designs. Generally, thermally stable ceramic inks of digital primary colors(cyan, magenta, yellow, black) are required for ink-jet printing of full color image on ceramic tile. Here, we synthesized an aqueous glass-ceramic ink, which is free of Volatile organic compound(VOC) evolution, and investigated its inkjet printability. $CoAl_2O_4$ inorganic pigment and glass frit were dispersed in aqueous solution, and rheological behavior was optimized. The formulated glass-ceramic ink was suitably jetted as single sphere-shaped droplets without satellite drops. After ink-jet printing and firing processes, the printed glass-ceramic ink pattern on glazed ceramic tile was stably maintained without ink spreading phenomena and showed an improved scratch resistance.

• 한국재료학회지
• /
• 제16권5호
• /
• pp.329-335
• /
• 2006

In order to improve thermal efficiency of the fossil fuel power plants, we need to develop advanced materials with superior durability in the ultra-super critical state, which requires surface modifications for superior surface properties. In this study, we coated the Incoloy 901 and 12-17Cr steels for turbine buckets and valves with nitriding, boriding, and $Cr_3C_2-NiCr$ HVOF(high velocity oxygen flow) method. Then the samples were heat treated at $650^{\circ}C$ for 100 hours in vacuum. We analyzed the evolution behaviors of nitrides such as $Fe_3N,\;Fe_4N$, and CrN and borides such as FeB and $Fe_2B$ with XRD and SEM/EDS by comparing hardnesses and compositions of the coated layers before and after the heat treatments.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 추계학술대회 논문집
• /
• pp.186-187
• /
• 2008

Electrical resistivity in hydrate-bearing sediments is sensitive to porosity, gas hydrate saturation, gas content, pore fluid composition, and temperature, so electrical measurements such as well logs and electromagnetic surveys have been used to explore gas hydrate-bearing formation. The high pressure tomography cell is designed considering the effect of electrode configuration and electrical shielding on tomography measurements and the safety. The evolution of electrical conductivity during $CO_2$ hydrate formation and dissociation reflects the combined effects of concurrent changes that include ionization of dissolved $CO_2$, temperature-dependent ionic mobility, changes in the degree of saturation, ion exclusion, surface conduction, and porosity changes. Measurements during hydrate formation and dissociation require careful analysis to properly interpret signatures, in particular when out-of plane conductivity anomalies prevail.

• 산업기술연구
• /
• 제42권1호
• /
• pp.7-12
• /
• 2022

High nickel layered oxide cathodes are gaining increasing attention for lithium-ion batteries due to their higher energy density and lower cost compared to LiCoO₂. However, they suffer from the formation of residual lithium on the surface in the form of LiOH and Li₂CO₃ on exposure to ambient air. The residual lithium causes notorious issues, such as slurry gelation during electrode preparation and gas evolution during cell cycling. In this review, we investigate the residual lithium issues through its impact on cathode slurry instability based on deformed polyvinylidene fluoride (PVdF) as well as its formation and reduction mechanism in terms of inherently off-stoichiometric synthesis of high nickel cathodes. Additionally, new analysis method with anhydrous methanol was introduced to exclude Li⁺/H⁺ exchange effect during sample preparation with distilled water. We hope that this review would contribute to encouraging the academic efforts to consider practical aspects and mitigation in global high-energy-density lithium-ion battery manufacturers.