• Journal of Korea Foundry Society
• /
• v.28 no.6
• /
• pp.273-281
• /
• 2008

Effects of alloying elements on the mechanical properties of hardened and austempered 3.60wt%C - 2.50wt%C ductile cast iron were investigated. Strength and hardness were increased and ductility was decreased as the amount of alloying element increased. The increasing effect of copper addition on the strength was the most pronounced. The strength and hardness were greatly increased and ductility was decreased by hardening. The effect of alloying element on the mechanical properties of the hardened ductile cast iron was not so pronounced due to the high contents of C and Si. The strength and hardness of austempered ductile cast iron were greatly increased, meanwhile the difference of strength from that of hardened one was not so big. The ductility of the former was higher than that of the latter. The strength and ductility of austempered ductile cast iron with 0.25%Mn were the maximum of all Mn added ones. The maximum strength of that was obtained with the addition of 0.80wt%Cu or 2.00wt%Ni along with this amount of Mn added.

• Journal of Bio-Environment Control
• /
• v.26 no.4
• /
• pp.324-332
• /
• 2017

The comparative experiments were conducted for single span greenhouses where cucumbers were cultivated to analyze the effect of heating between a carbon fiber electric heating element heater and an oil hot air heater in terms of the inside climate, energy consumption and plant growth. In order to analyze the effect of heating capacity, 6, 9, and 16 kW of electric powers were supplied to the electric heating element for same setting temperature of 15?. As a result, as the heating capacity increased, the number of ON-OFF cycles of the electric heating element and the temperature inside the greenhouse increased proportionally. In the comparison of two heaters, it was shown that the temperature and relative humidity distributions of the electric heating element installed greenhouse was much uniform than those of the oil hot air heater installed greenhouse. The heating energy consumptions during the heating period of 79 days were 867L for the oil hot air heater and 8,959 kWh for the electric heating element heater, and the heating costs were 607 and 403 thousand won respectively. In the electric heating element installed greenhouse, the cucumber growth was slightly better and the yield was 4.3% higher than those of the oil hot air heater installed greenhouse, but there were no statically significant difference in the cucumber growth and yield between greenhouses.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2001.04a
• /
• pp.278-286
• /
• 2001

The purpose of this paper is to suggest an analytical technique for time history analysis of R/C frame structure using high-strength concrete under seismic loading. Current researches in hysteretic model of structral elements using high-strength concrete are not enough. It is the cause of error that apply hysteretic model of element using normal-strength concrete to the inelastic analysis of high-strength concrete R/C frame structures. In this paper time history analysis using IDARC and DRAIN programs was performed for a 2-bay, 20-story R/C frame structures. Particularly nonlinear dynamic analysis was performed by IDARC program that was applied hysteretic model of structural element using high-strength concrete. centro earthquake 1940 NS waves was used in the analysis and its peak ground accelerations are changed to be 0.12g, 0.25g

• 전기의세계
• /
• v.27 no.6
• /
• pp.54-57
• /
• 1978

An analytical investigation has been carried out for the motion of moving element in electro-dynamometer type directional power relay under A.C source. For the more a time dependent kinetic performance of the element can also be deduced for the D.C component in fault current. The results obtained thus for show that, in the relay with stopper, the performance time for the equal D.C and A.C component can be shorten ca. 0.5Hz in comparison with the fact, the performance time exhibits to delay ca. 0.75Hz under the same conditions for the case of the relay without stopper, it appear that these differences of performance times will not give vise any difficultys for the apects of practical case, however, the obtain results can be applicable in the course of the design of the relay.

• Journal of the Microelectronics and Packaging Society
• /
• v.10 no.3
• /
• pp.1-7
• /
• 2003

The crystallized stable cobalt silicide$(CoSi_2)$ films were prepared on $poly-Si/SiO_2/Si$substrates for the application of inkjet printing head as a heating element with omega shape. The structural images and temperature resistance coefficient were investigated. The value of temperature resistance coefficient of the heating element was found to be about $0.0014/^{\circ}C$. The maximum power of the heating element was 2 W at the applied voltage of 2 V, 10 kHz in frequency and $1{\mu}s$ in pulse width. From the investigation of fatigue property according to the repeated applied voltages, there was no drastic changes in the resistances of heating element under the condition of $10^8$ pulsed cycles at below 15 V biased voltage. In contrast, the resistance of heating element was greatly increased at $10^6$ pulsed cycles when the heating element was operated at 17 V.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.4
• /
• pp.799-804
• /
• 2012

To converter time information to digital information Time-to-Digital Converter(TDC) is designed by using analog delay elements. To obtain the temperature stable characteristics the circuit is designed and the operation of the designed circuit is confirmed by HSPICE. The characteristics variation of the designed delay element with temperature is from -0.18% to 0.126% compared to room temperature characteristics when the temperature is varied from $-20^{\circ}C$ tp $70^{\circ}C$. Time difference is from -0.18% to 0.12% compared to room temperature characteristic when the temperature is varied from $-20^{\circ}C$ tp $70^{\circ}C$. The time difference is simulated when the digital output is 15. However the time difference is from -1.09% to 1.28% in the TDC using temperature non-stable analog delay elements.

• Korean Institute of Interior Design Journal
• /
• v.20 no.2
• /
• pp.72-84
• /
• 2011

In accordance with an active development, we now enjoy web 2.0 generation centering bilateral participation through the web 1.0 environment mainly providing the offering information and take a step web 3.0 understanding information by itself. The same time of digital technic development, consumption market arrived at market3.0 generation, also passed by market 1.0 and went via market 2.0 based on bilateral participation and understanding. This change have the marketing implement index changed as well. Nowadays, 7C is generalized of making up sensibility, emotion, communication, relationship, customization and interactive built as a major strategy from the day of 3p focused on customer environment, service process and 4P focused on physical quality of product. It isn't that brand and merchandise create life and experience like as past. It is focused on embodiment of a way of life, culture and creative experience from consumers' own. This treatise, therefore, fixes the object as flagship store positively reflecting the change and examine the change of a marketing code element and social factor stimulating customer behavior change. As a condition of this study, It fixes Maslow Motivation Theory as the main index of customer behavior, and 7C as the marketing code. This treatise ultimately studies the index of flagship store discussion based on domestic outdoor brand cases.

• Structural Engineering and Mechanics
• /
• v.6 no.7
• /
• pp.727-746
• /
• 1998

Finite element models and numerical results are presented for bending and natural vibration using the unified third-order plate theory developed in Part 1 of this paper. The unified third-order theory contains the classical, first-order, and other third-order plate theories as special cases. Analytical solutions are developed using the Navier and L$\acute{e}$vy solution procedures (see Part 1 of the paper). Displacement finite element models of the unified third-order theory are developed herein. The finite element models are based on $C^0$ interpolation of the inplane displacements and rotation functions and $C^1$ interpolation of the transverse deflection. Numerical results of bending and natural vibration are presented to evaluate the accuracy of various plate theories.

• Structural Engineering and Mechanics
• /
• v.13 no.1
• /
• pp.53-74
• /
• 2002

Composites exhibit larger dispersion in their material properties compared to conventional materials due to larger number of parameters associated with their manufacturing processes. A $C^0$ finite element method has been used for arriving at an eigenvalue problem using higher order shear deformation theory for initial buckling of laminated composite plates. The material properties have been modeled as basic random variables. A mean-centered first order perturbation technique has been used to find the probabilistic characteristics of the buckling loads with different edge conditions. Results have been compared with Monte Carlo simulation, and those available in literature.

• Journal of Power System Engineering
• /
• v.4 no.1
• /
• pp.68-73
• /
• 2000

A mixed degree finite element solutions using hierarchical elements are investigated for convergences on a 2-D simple cases. Elements are generated block by block and each block is assigned an arbitrary solution degree. The numerical study showed that a well constructed blocks can increase the convergence and accuracy of finite element solutions. Also, it has been found that for higher order elements, the convergence trends can be deteriorated for smaller mesh sizes. A procedure for a variable fixed boundary condition has been included.