• 한국물환경학회지
• /
• 제25권4호
• /
• pp.522-529
• /
• 2009

To supply safe drinking water to areas lacking in water supply and drainage system, such as rural area and military bases in proximity to Demilitarized Zone, effective method for treating organic contaminants such as MTBE is required. This study focuses on seeking optimal conditions for effective degradation of MTBE using a bath type ultrasound reactor. Effectiveness of MTBE degradation by ultrasound is dependent on the frequency, power, temperature, treatment volume, initial concentration, catalyst, etc. In this study the degradation rate of MTBE by ultrasound was proportional to power/unit volume ratio and removal is relatively more efficient for 0.1 mM than for 1 mM of MTBE solution. Efficiency of ultrasound treatment for 1 mM MTBE solution was enhanced under bath temperature of $30^{\circ}C$ compared to $4^{\circ}C$, but the temperature effect was negligible for 0.1 mM MTBE solution. Also for 0.1 mM MTBE solution, effect of catalyst such as $TiO_2$ and $Fe^0$ on treatment speed was negligible, and zeolite even increases the time taken for the degradation. Under these specific experimental conditions of this study, the most determinant factor for degradation rate of MTBE in solution was frequency and power of ultrasound. The results have shown that a continuous ultrasound reactor system can be used for small scale remediation of organically polluted groundwater, under optimal conditions.

• Journal of Korean Society for Atmospheric Environment
• /
• 제17권E1호
• /
• pp.1-7
• /
• 2001

The elemental characteristics of atmospheric aerosols were investigated as a function of particle size and water solubility. The aerosol particles were samples at 12 individual size ranges between 0.01 and 30㎛. Collected aerosol particles were separated into both soluble and insoluble components. The concentrations of 15 elements in both components were determined by a PIXE analysis using a 2.0 MeV-proton beam. In general, the mass size distribution of particulate matter was represented as a bimodal distribution. The maximum rations of S in July and December were 5.5 and 3.8 %, and they appeared in the size range of 0.47∼1.17㎛(stage No. 6 or 7) . The ratios of a S at non-separated size were 3.1 and 2.2 % in July and December, respectively, On the other hand, the maximum rations of Si in July and December were 7.0 and 5.4% and they appeared in the size range of 5.1∼30㎛(stage No. 0∼2). The ratios of Si at the non-separated size were 2.1 and 1.8% in July and December, respectively, The mass diameter of 12 elements ranged between 0.59㎛ of S and 3.20 of Fe. More than 90% of atmospheric aerosols consisted of the light elements such as C, N, O, H and Al. The soluble component was dominant in the smaller size range and the insoluble component in the larger size range. Large portions of Si. Ti and Fe existed in insoluble state. By contrast, S, Cl, Ca, Zn and Br were dissolved in water.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.346-346
• /
• 2007

압전세라믹 재료는 현재 압전 변압기, actuator, transducer, sensor, speaker 등에 광범위하게 이용이 되고 있다. 이 중에서 압전세라믹 소결체를 이용한 스피커의 제조는 가공이 까다롭고, 대형의 크기로 제작 시 소자가 깨지는 등의 많은 제약을 받고 있으며, 저음 특성이 떨어져 응용 범위가 한정되어 있다. 따라서 최근에는 이러한 단점을 극복하기 위하여 세라믹/고분자 복합체를 이용한 필름 스피커를 제작하고자 시도하고 있다. 이러한 세라믹/고분자 0-3형 압전 복합체를 이용할 경우, 제품의 경량화를 실현할 수 있고, 크기나 환경의 영향을 거의 받지 않으므로, 고기능성 스피커로의 응용에 적합할 것으로 보인다. 따라서 본 연구에서는 PZT계의 세라믹와 PVDF, PVDF-TrFE, Polyester, acrylic resin 등의 여러 고분자 물질과의 복합체를 제조하여 압전특성을 평가하였다. 본 실험은 먼저 $(Pb_{1-a-b}Ba_aCd_b)(Zr_xTi_{1-x})_{1-c-d}(Ni_{1/3}Nb_{2/3})_c(Zn_{1/3}Nb_{2/3})_dO_3$ (이하 PZT라 표기)의 최적화 조성을 선택하여, $1050^{\circ}C$에서 소결된 분말을 48시간 ball milling방법 로 약 $1{\mu}m$ 크기로 분쇄하였다. 고분자 물질들은 알맞은 용제들을 선택하여 녹였다. 그 다음 소결된 PZT분말과 고분자를 50:50, 60:40, 65:35, 70:30등의 무게 분율로 혼합하고, 분산제, 소포제 등을 첨가하여 3단 roll mill을 이용하여 충분히 분산시켜 페이스트 (Paste)를 제조하였다. 제조된 페이스트를 ITO가 코팅된 PET필름 위에 스크린 프린팅 법을 사용하여 인쇄하여 $120^{\circ}C$에서 5분간 건조하였다. 코팅된 복합체의 두께는 약 $80{\mu}m$ 정도로 측정되었다. Ag 페이스트를 이용한 상부 전극 형성에도 스크린 프린팅 법을 적용하였다. 이를 $120^{\circ}C$에서 4 kV/mm의 DC 전계로 분극 공정을 수행한 후 전기적 특성을 평가하였다. 유전특성을 조사하기 위해서 LCR meter (EDC-1620)를 사용하였고, 시편의 결정구조는 XRD (Rigaku; D/MAX-2500H)을 통해 분석하였으며, 전자현미경(SEM)을 이용하여 미세구조를 분석하였다. 압전 전하상수$(d_{33})$ 값은 APC 8000 모델을 이용하여 측정하였다. PZT의 혼합비가 증가할수록 비유전율 및 압전 전하 상수 등의 전기적 특성이 증가되었다. 또 여러 고분자 물질 중에서 PVDF-TrFE 수지가 가장 우수한 특성을 보였다. 이는 PVDF-TrFE 수지가 압전성을 나타내기 때문인 것으로 판단되었다.

• 한국전기전자재료학회논문지
• /
• 제31권1호
• /
• pp.19-23
• /
• 2018

In a Pb-included piezoelectric composition, $Sr_yPb_{1-y}[(Zn_{1/3}Nb_{2/3})_x-(Ni_{1/3}Nb_{2/3})_{0.2}-(Zr_{0.46}Ti_{0.54})_{0.8-x}]O_3$ was selected in order to attain high piezoelectric properties. According to the PZN ratio (x) and the amount of Sr doping (y), the crystal structure, microstructure and piezoelectric properties were measured and evaluated. In the case of Sr 4 mol% doping, the piezoelectric properties were the highest for a PZN ratio of 0.1. In this condition, the grain size was larger and the intensity was higher. With the PZN ratio fixed and varying the Sr doping, the piezoelectric properties increased until 10 mol% doping and then decreased for over 12 mol% doping. In the case of x＝0.1 and y＝10 mol%, the best piezoelectric properties were obtained, i.e., $d_{33}=660pC/N$ and $k_p=68.5%$, and these values seem to be related to the grain size and crystal structure.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2011년도 임시총회 및 하계학술연구발표회
• /
• pp.7-8
• /
• 2011

Basically, the lattice mismatch between film and substrate can make those BiFeO3(BFO) films distorted with strain structure. BFO phase can be stabilized on LaAlO3(LAO) represents the example of a multiferroic with giant axial ratio. Its crystal structure is not strictly tetragonal, but tetragonal with a slight monoclinic distortion and related to the rotation of the oxygen octahedra. In this study, we show that phases with a tetragonal-like epitaxial BFO films can indeed be ferroelectric and also can be stabilized via epitaxial growth onto LAO. Recent reports on epitaxial BFO films show that the crystal structure changes from nearly rhombohedral ("R-like") to nearly tetragonal("T-like") at strains exceeding approximately -4.5%, with the "T-like" structure being characterized by a highly enhanced c/a ratio. While both the "R-like" and the "T-like" phases are monoclinic, our detailed x-ray diffraction results reveal asymmetry change from MA and MC type, respectively. By applying additional strain or by modifying the unit cell volume of the film by substituting Ba for Bi, the monoclinic distortion in the "T-like" MC phase is reduced, i.e. the system approaches a true tetragonal symmetry. There are two different M-H loops for $Bi_{1-x}Ba_xFeO_{3-{\delta}}$(BBFO) and BFO films on SrTiO3(STO) & LAO substrates. Along with the ferroelectric characterization, these magnetic data indicate that the BFO phase stabilized on LAO represents the first example of a multiferroic with giant axial ratio. However, there is a significant difference between this phase and other predicted ferroelectrics with a giant axial ratio: its crystal structure is not strictly tetragonal, but tetragonal with a slight monoclinic distortion. Therefore, in going from bulk to highly-strained films, a phase sequence of rhombohedral(R)-to-monoclinic ["R-like" MA-to-monoclinic, "T-like" MC-to-tetragonal (T)] is observed. This sequence is otherwise seen only near morphotropic phase boundaries in lead-based solid-solution perovskites (i.e. near a compositionally induced phase instability), where it can be controlled by electric field, temperature, or composition. Our results show that this evolution can occur in a lead-free, stoichiometric material and can be induced by stress alone. Those major results are summarized as follows ; 1) Ba-doping increases the unit cell volume, 2) BBFO on LAO can be fully strained up to x=0.08 as a strain limit (Fig. 1), 3) P(E) & M(H) properties can be tuned by the variation of composition, strain, and film thickness.

• 한국식품영양과학회지
• /
• 제28권2호
• /
• pp.277-284
• /
• 1999

To confirm the food quality of conventionally processed fish extracts, protein quality of boiled crucian carp(Carassius carassius) and bastard halibut(Paralichthys olivaceus) extracts and their residues were evaluated. For the both fish extracts, some of the essential amino acids were lowered significantly but two times more proline and glycine were detected in extracts than those in raw fish meats. Boiling(100oC, 5 hours) caused 1.8(crucian carp)~2.4(bastard halibut) times more total free amino acid contents in fish extracts as compared to those in original fish meats. Taurine, glutamic acid, proline, lysine, and ammonia were the predominant free amino acids released in fish extracts. In vitro digestibility of boiled fish extracts were lower at a level of 4~6% than those of raw fish meats. Fish extraction residue had a higher in vitro digestibility and had a 60% lower level of TI than that of original fish meats. 18(bastard halibut)~ 24%(crucian carp) of available lysine was reduced in boiled fish extracts but a remarkable variation was not noted between extracts and residues. PERs and NPRs of fish extracts were significantly lower than those of casein, while those values of extraction residue were slightly higher as compared to those of control(ANRC casein). In vivo apparent digestibility exhibited a similar trend to in vitro digestibility. Hematological properties in serum of rat fed with fish extracts and residue were not changed significantly but the serum cholesterol concentration were reduced in rats fed fish extraction residue comparing with those of control. These results suggest that body weight loss due to fish extracts may not affect physiological changes.

• 한국전기전자재료학회논문지
• /
• 제16권7호
• /
• pp.573-578
• /
• 2003

Low temperature selective epitaxial growth of Si and SiGe has been obtained using an industrial single wafer chemical vapor deposition module operating at reduced pressure. Epitaxial Si and heteroepitaxial SiGe deposition with Ge content about 20 % has been studied as extrinsic base for self-aligned heterojunction bipolar transistors(HBTs), which helps to reduce the parasitic resistance to obtain higher maximum oscillation frequencies(f$\_$max/). The dependence of Si and SiGe deposition rates on exposed windows and their evolution with the addition of HCl to the gas mixture are investigated. SiH$_2$Cl$_2$ was used as the source of Si SEG(Selective Epitaxial Growth) and GeH$_4$ was added to grow SiGe SEG. The addition of HCl into the gas mixture allows increasing an incubation time even low growth temperature of 675∼725$^{\circ}C$. In addition, the selectivity is enhanced for the SiGe alloy and it was proposed that the incubation time for the polycrystalline deposit on the oxide is increased probably due to GeO formation. On the other hand, when only SiGe SEG(Selective Epitaxial Growth) layer is used for extrinsic base, it shows a higher sheet resistance with Ti-silicide because of Ge segregation to the interface, but in case of Si or Si/SiGe SEG layer, the sheet resistance is decreased up to 70 %.

• 한국재료학회지
• /
• 제19권2호
• /
• pp.61-67
• /
• 2009

Electrolessly deposited Co (Re,P) was investigated as a possible capping layer for Cu wires. 50 nm Co (Re,P) films were deposited on Cu/Ti-coated silicon wafers which acted as a catalytic seed and an adhesion layer, respectively. To obtain the optimized bath composition, electroless deposition was studied through an electrochemical approach via a linear sweep voltammetry analysis. The results of using this method showed that the best deposition conditions were a $CoSO_4$ concentration of 0.082 mol/l, a solution pH of 9, a $KReO_4$ concentration of 0.0003 mol/l and sodium hypophosphite concentration of 0.1 mol/L at $80^{\circ}C$. The thermal stability of the Co (Re,P) layer as a barrier preventing Cu was evaluated using Auger electron spectroscopy and a Scanning calorimeter. The measurement results showed that Re impurities stabilized the h.c.p. phase up to $550^{\circ}C$ and that the Co (Re,P) film efficiently blocked Cu diffusion under an annealing temperature of $400^{\circ}C$ for 1hr. The good barrier properties that were observed can be explained by the nano-sized grains along with the blocking effect of the impurities at the fast diffusion path of the grain boundaries. The transformation temperature from the amorphous to crystal structure is increased by doping the Re.

• 한국결정성장학회지
• /
• 제32권1호
• /
• pp.7-11
• /
• 2022

한미보석감정원은 최근에 5개의 투명한 합성 모이사나이트를 검사했다. 그 샘플들은 라운드 브릴리언트 컷의 무색, 핑크, 황색, 청색, 적색 컬러와 0.93~0.96 ct 중량을 가지고 있었다. FT-IR과 Raman 분석 결과 합성 모이사나이트임을 확인하였고, 확대검사 결과 무색을 제외한 나머지 샘플에서 코팅의 흔적이 발견되었다. EDXRF 분석 결과 무색 샘플을 제외한 모든 샘플의 코팅부분에서 Ca, Ti, Co의 미량원소가 검출되었다. 무색 샘플의 Raman 분석에서 탄소 원자의 sp³ bonding에 의해 생성되는 1332 cm^-1 또는 graphite와 관련된 sp² bonding에 의해 생성되는 ~1550 cm^-1는 발견되지 않았다. 무색 샘플의 SEM 이미지에서도 코팅의 흔적은 발견되지 않았으나, TEM 이미지에서 3~8 nm의 코팅층의 존재가 발견됐다. EDX line 프로파일과 EDX elements map을 통해 무색 샘플의 코팅층을 구성하는 원소는 C, Si, O로 추정된다.

• 한국재료학회지
• /
• 제8권7호
• /
• pp.621-627
• /
• 1998

단결정 Si(100) 기판과 비정질 Si 기판위에 Co/Zr 이중층을 이용하여 형성시킨 Co 실리사이드의 성장 거동에 대하여 연구하였다. 전자빔 증착기를 사용하여 단결정과 비정질 Si 기판위에 Zr $50\AA$과 Co $100\AA$을 차례로 증착한 박막을 50$0^{\circ}C$부터 $800^{\circ}C$까지 $100^{\circ}C$ 간격으로 질소 분위기에서 30초 동안 급속열처리를 하여 Co 실리사이드를 형성시켰다. 각 온도에서 열처리된 시편의 상형성, 화학적 조성, 계면의 형상, 전기적 특성을 XRD, AES, RBS, TEM, HRTEM 등으로 분석하였다. 분석 결과 $CoSi_2$ 상이 단결정 기판에서는 $700^{\circ}C$ 이상에서 기판과 정합성장을 하였고 비정질 기판에서는 다결정 성장을 하였으며 Co 실리사이드의 상형성 온도는 단결정 기판에서보다 비정질 기판에서 $100^{\circ}C$정도 낮아졌다. $CoSi_2$와 같은 Co rich 중간상은 두 기판 모두 형성되지 않았으며 초기 Co 실리사이드의 상형성 온도는 Co 단일층으로 상을 형성시킬 때 보다 더 높았다. Co 실리사이드와 Si 기판의 계면의 형상은 단결정 기판의 경우보다 비정질 기판에서 더 균질하였다. 박막의 면저항은 $600^{\circ}C$이하의 열처리 온도에서는 비정질 기판에서 형성된 Co 실리사이드 박막이 더 낮은 값을 나타내었고 그 이상의 열처리 온도에서는 단결정 기판에서 형성된 박막의 면저항값이 더 낮은 값을 나타내었으며 두가지 기판에서 형성된 박막 모두$ 800^{\circ}C$에서 가장 낮은 면저항 값을 보였다.TEX>$10^{-8}$ A/$\textrm{cm}^2$로 양질의 SrTiO$_3$박막을 제조하였다.는 과정에서 전세계 수준에서 멸종위기 식물을 목록화가 필요하다. 특히, 목록 작업이 완성되면 해당 분류군에 대한 기본적인 자료 수집과 장단기 조사과정으로서, 해당 분류군에 대한 멸종위협 요인을 수집하고, 이 자료를 근간으로 정량적으로 IUCN 적색목록 평가방식이 추진할 필요가 있다.he oscillations are active in the derived unit hydrograph. 3)The parameter estimates are validated by extending the model to the Soyang river Dam site with elimination of the autocorrelation in the disturbances. Finally, this paper illustrates the application of the multiple regression model to drive an optimal unit hydrograph dealing with the multicollinearity and the autocorrelation which cause some problems. 우선적으로 고려하여 사용할 농약을 선택해야 할 것으로 보이나, 그 외 약제의 잔류성, 사용량, 사용시기와 함께 기후조건, 토양의 투수성, 토층이 깊이, 지하수 깊이 등의 지역적인 특성들이 농약의 용탈잠재성에 미치는 영향도 더욱 구체적으로 파악되어야 할 것이며 농약의 선택 과정에서도 이러한 특성들이 앞으로 고려되어야 할 것이다.calenol 및 citrostadienol 등이 함유(含有)되어 있었다. 6. 4-desmethylsterol fraction에 는 sitosterol (74.6%)이