• 신재생에너지
• /
• 제18권2호
• /
• pp.40-49
• /
• 2022

In this study, the phase and electrochemical properties of Co and Ti substituted layered perovskites SmBaCo_2-xTi_xO_5+d (x=0.5, 0.7, 1.0, 1.1, 1.3, and 1.5) were analyzed, and their application as electrodes in solid oxide fuel cells (SOFCs) were evaluated. After calcination at 1300℃ for 6 h, a single phase was observed for two compositions of the SmBaCo_2-xTi_xO_5+d oxide system, SmBaCoTiO_5+d (x=1.0) and SmBaCo_0.9Ti_1.1O_5+d (x=1.1). However, the phases of SmBaCoTiO_5+d (SBCTO) and SmTiO₃ coexisted for compositions with x≥1.3 (Ti content). In contrast, for compositions of x≤0.7, the SmBaCo₂O_5+d phase was observed instead of the SmTiO₃ phase. To evaluate the applicability of these materials as SOFC electrodes, the electrical conductivities were measured under various atmospheres (air, N₂, and H₂). SBCTO exhibited stable semi-conductor electrical conductivity behavior in an air and N₂ atmosphere. However, SBCTO showed insulator behavior at temperatures above 600℃ in a H₂ atmosphere. Therefore, SBCTO may only be used as cathode materials. Moreover, SBCTO had an area specific resistance (ASR) value of 0.140 Ω·cm² at 750℃.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.35-36
• /
• 2008

PTC thermistor are characterized by an increase in the electrical resistance with temperature. The PTC materials of middle Curie point were produced or that of high Curie point (above $200^{\circ}C$), it was determined that compositional modifications of $Pb^{2+}$ for $Ba^{2+}$ produce change sin the Curie point to higher temperature. PTC ceramic materials with the Curie point above $120^{\circ}C$ were prepared by adding $PbTiO_3$, PbO or $Pb_3O_4$ into $BaTiO_3$. Thereby, adding $Pb^{2+}$ into $BaTiO_3$-based PTC material to improve Tc was studied broadly, however, weal know that PbO was poisonous and prone to volatilize, then to pollute the circumstance and hurt to people, so we should dope other innocuous additives instead of lead to increase Tc of composite PTC material. In order to prepare lead-free $BaTiO_3$-based PTC with middle Curie point, the incorporation on $Bi_{1/2}K_{1/2}TiO_3$ into $BaTiO_3$-based ceramics was investigated on samples containing 0, 1, 2, 3, 4, and 50mol% of $Bi_{1/2}K_{1/2}TiO_3$. $Bi_{1/2}K_{1/2}TiO_3$ was compounded as standby material by conventional solid-state reaction technique. The starting materials were $Bi_2O_3$, $K_2CO_3$, $BaCO_3$ and $TiO_2$ powder, and using solid-state reaction method, too. The microstructures of samples were investigated by SEM, DSC, XRD and dielectric properties. Phase composition and lattice parameters were investigated by X-ray diffraction.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 추계학술대회 논문집
• /
• pp.413-416
• /
• 1996

The ceramic dielectrics were fabricated by mixing of Mn $O_2$ and ZnO at (B $a_{0.85}$ $Ca_{0.15}$)Ti $O_3$ and studied for dielectric relaxation characteristics. The dielectric relaxation time was increased by space charge polarization of palaelectric layer at the low temperature and frequency but it was decreased by Interface polarization at the high temperature and frequency. The remnant polarization and coercive field of ceramic dielectrics was decreased by rising temperature.ure.

• 한국세라믹학회:학술대회논문집
• /
• 한국세라믹학회 2003년도 춘계총회 및 연구발표회 초록집
• /
• pp.99.2-99
• /
• 2003

• 한국전기전자재료학회논문지
• /
• 제11권11호
• /
• pp.947-953
• /
• 1998

The microwave dielectric properties of X BaO-0.15($Nd_{0.87}Bi_{0.13})_2O_3-(0.85-X)TiO_2 (X=0.14~0.17) and 0.16BaO-0.15(Bi_xNd_{1-x})_2O_3-0.69TiO_2$ (X=0.12~0.15) ceramics sintered at 1320~$1380^{\circ}C$ were investigated. The microwave dielectric properties of X BaO-0.15(Nd_{0.87}Bi_{0.13})_2O_3-(0.85-X)TiO_2$ (X=0.14~0.17) can be controlled effectively by adjusting X content : with increasing X from 0.14 to 0.17 both dielectric constant and temperature coefficient of resonant frequency decreased from 94.6 to 86 and from 22 ppm/^${\circ}C to -7 ppm/^{\circ}C$, respectively, while quality factor increased from 1300 to 1920 (at 4GHz). The microwave dielectric properties of 0.16BaO-0.15(Bi_x/Nd_{1-x2}O_3 -0.69TiO_2$ (X=0.12~0.15) can be controlled effectively by adjusting X content : with increasing X from 0.12 to 0.15 both quality factor and temperature coefficient of resonant frequency decreased from 1920 to 1430 and from 9 ppm/^${\circ}C to -10 ppm/^{\circ}C$, respectively, while dielectric constant increased from 87.5 to 92.6.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.296-297
• /
• 2006

A conventional oxide method was used to fabricate $Ba_{0.5}Sr_{0.5}TiO_3$(BST) ceramic plates doped by MgO from 10 to 60 wt%. The structural and dielectric properties of BST were investigated as a fraction of MgO dopant concentration. The dielectric properties of the MgO doped BST were strongly dependent on the MgO contents. The dielectric constant and dielectric loss of MgO doped BST decreased with increasing MgO content.

• 센서학회지
• /
• 제18권5호
• /
• pp.343-348
• /
• 2009

$NiO{\cdot}(Co_{0.25}Mn_{0.75})_2O_3$(Mn-Ni-Co) and $Ba_{0.5}Sr_{0.5}TiO_3$(BST) thick films were screen printed on Pt patterned alumina substrate to investigate the effects of sintering temperature on humidity and temperature sensing properties of ceramic sensors. A raise in sintering temperature increased resistance and B constant of the Mn-Ni-Co temperature sensor. This may have derived from the synergic effects of the reduction in charge carriers caused by the substitution of Co for Mn as well as the formation of microcracks from the difference in thermal expansion coefficients. Dependence of resistance on humidity of the Mn-Ni-Co temperature sensor, however, was not found. BST films sintered at temperatures in the range of $1100^{\circ}C$ to $1150^{\circ}C$ showed excellent humidity sensing properties. The BST humidity sensor was faster in its response than the Mn-Ni-Co temperature sensor. The humidity sensor, however, proved to be unstable under various temperatures, suggesting a need for a temperature stabilizing device. In contrast, the Mn-Ni-Co temperature sensor was stable under humid conditions.

• 한국세라믹학회지
• /
• 제19권4호
• /
• pp.316-320
• /
• 1982

The effect of the additive on dielectric properties of $BaTiO_3$ containing 0.030 mol% $Dy_2O_3$ was investigated function of frequency from 5$\times$104 to 0.3$\times$107cps and temperature from 25 to 1$25^{\circ}C$. The dielectric constant increased with increasing $Dy_2O_3$ concentration from 0 to 0.05mol% due to space charge polarization. However, the dielectric constant decreased for further increase of $Dy_2O_3$ concentration due to density increase. The dielectric constant exhibits rapid change at the Curie temperature and the Curie temperature drops from 122 to 116$^{\circ}C$ with increasing amount of $Dy_2O_3$ concentration.

• 한국세라믹학회지
• /
• 제43권9호
• /
• pp.569-574
• /
• 2006

Transparent glass-ceramics containing fresnoite crystals have been prepared by controlled heat treatment in $K_2O-BaO-TiO_2-SiO_2$ and their nonlinear optical and luminescent properties were investigated using Maker fringe method and Spectrofluorometer. The second harmonic generation was observed in all samples and the values decreased with increasing $K_2O$ content. The luminescence of blue light at ${\sim}482nm$ could be observed and it was shown that the luminescent property was controlled by the $K_2O$ content.

• Journal of Ceramic Processing Research
• /
• 제20권6호
• /
• pp.603-608
• /
• 2019

In this study, the multilayered thin films of (Ba,Sr)TiO3/K(Ta,Nb)O3 were fabricated by the sol-gel and spin coating methods, and their structural and electrical properties were investigated. The specimen showed polycrystalline X-ray diffraction (XRD) characteristics with a tetragonal structure. The average grain size and film thickness for one coating were about 30~40nm and 60nm, respectively. The phase transition temperature of specimen was lower than 10 ℃. The dielectric constant and loss at 20 ℃ of the specimen coated six times were 1,231 and 0.69, respectively. The rate of change in dielectric constant at an applied direct current (DC) voltage of the six times coated thin films was 17.3%/V. The electrocaloric effect was the highest around the temperature at which the remanent polarization rapidly changed. When an electric field of 660kV/cm was applied to the triply coated thin films, the highest electrocaloric property of 4.41 ℃ was observed.