• Journal of Sensor Science and Technology
• /
• v.10 no.6
• /
• pp.295-303
• /
• 2001

White emission thin film electroluminecent device was fabricated with ZnS for phosphor layers and BST ferroelectric thin film for insulating layers. The ZnS:Mn and $ZnS:SmF_3$ layers were used for emission of red color. Also the $ZnS:TbF_3$ and $ZnS:AgF_3$ layers were used to emission of green and blue color, respectively. And the fabrication conditions of the BST insulating layers were followings, that is, the composition ratio of target, substrate temperature, working pressure and operating gas ratio were $Ba_{0.5}Sr_{0.5}Ti_{0.3}$, $400^{\circ}C$, 30 mTorr and 9:1, respectively. The thickness of phosphor were 150 nm for each layers and the insulating layers of upper and bottom were 400 nm and 200 nm, respectively. The luminesence threshold voltage was $75\;V_{rms}$ and the maximum brightness of the thin film electroluminecent device was $3200\;cd/m^2$ at $100\;V_{rms}$.

• Economic and Environmental Geology
• /
• v.56 no.6
• /
• pp.745-764
• /
• 2023

In the Republic of Congo, Banded iron formations (BIFs) occur in two areas: the Chaillu Massif and the Ivindo Basement Complex, which are segments of the Archean Congo craton outcropping in the northwestern and southwestern parts of the country. They show interesting potential with significant mineral resources reaching 2 Bt and grades up to 60% Fe. BIFs consist mostly of oxide-rich facies (hematite/magnetite), but carbonate-rich facies are also highlighted. They are found across the country within the similar geological sequences composed of amphibolites, gneisses and greenschists. The Post-Archean Australian Shale (PAAS)-normalized patterns of BIFs show enrichment in elements such as SiO₂, Fe₂O₃, CaO, P₂O₅, Cr, Cu, Zn, Nb, Hf, U and depletion in TiO₂, Al₂O₃, MgO, Na₂O, K₂O, Sc, Th, Ba, Zr, Rb, Ni, V. REE diagrams show slight light REEs (rare earth elements; LREEs) compared to heavy REEs (HREEs), and positive La and Eu anomalies. The lithological associations, as well as the very high (Eu/Eu^*)_SN ratios> 1.8 shown by the BIFs, suggest that they are related to Algoma-type BIFs. The positive correlations between Zr and TiO₂, Al₂O₃, Hf suggest that the contamination comes mainly from felsic rocks, while the absence of correlations between MgO and Cr, Ni argues for negligeable contributions from mafic sources. Pr/Pr^* vs. Ce/Ce^* diagram indicates that the Congolese BIFs were formed in basins with redox heterogeneity, which varies from suboxic to anoxic and from oxic to anoxic conditions. They were formed through hydrothermal vents in the seawater, with relatively low proportions of detrital inputs derived from igneous sources through continental weathering. Some Congolese BIFs show high contents in Cr, Ni and Cu, which suggest that iron (Fe) and silicon (Si) have been leached through hydrothermal processes associated with submarine volcanism. We discussed their tectonic setting and depositional environment and proposed that they were deposited in extensional back-arc basins, which also recorded hydrothermal vent fluids.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.9
• /
• pp.776-780
• /
• 2009

In this study, the opto-electric properties of EL devices with PMN dielectric layer with variation of firing tempereature were investigated. For the PMN dielectric layer process, the paste was prepared by optimization of quantitative mixing of PMN powder, $BaTiO_3$, Glass Frit, $\alpha$-Terpineol and ethyl cellulose. The EL device stack consists of Alumina substrate ($Al_2O_3$), metallic electrode (Au), insulating layer (manufactured PMN paste), phosphor layer (ELPP- 030, ELK) and transparent electrode (ITO), which is well structure as a thick film EL device. The phase transformation properties of PMN dielectric with various firing temperatures of $150^{\circ}C$ to $850^{\circ}C$ was characterized by XRD. Also the opto-electric properties of EL devices with different firing temperature were investigated by LCR meter and spectrometer. We found the best opto-electric property was obtained at the condition of $550^{\circ}C$ firing which is 3432.96 $cd/m^2$ at 1948.3 pF Capacitance, 40 kHz Frequency, 40% Duty, Vth+330 V voltage.

• Journal of Korean Society of Forest Science
• /
• v.86 no.3
• /
• pp.324-333
• /
• 1997

The research has been made for the effects of the pollution by the abandoned coal mine drainage on the physical and chemical properties of soil, stream sediment and soil water. The soils overspreaded by the abandoned coal don't develop solum and the bulk density is $1.83g/m^3$, compared with $1.14-1.38g/m^3$ in the other forest soils. The soil pH range in coal bearing region ie, from 4.01 to 4.11 and non-coal bearing soil range is from 5.03 to 5.13. Heavy metals such as As, Cr, Ni, Mo and Ba of coal bearing soils and polluted stream sediments have larger concentration than those of non-coal content and non-polluted. Especially As and Mo concentrations are largely high in coal bearing. The relative ratios $K_2O/Na_2O$ of geochemical elements are higher in coal bearing soil and polluted stream sediments than those of non-coal bearing soils and non-polluted stream sediments as well as black shales of the Changri Formation. However, $MgO+Fe_2O_3+TiO_2/CaO+K_2O$ are the opposite trends, so that the ratios are lower in the polluted regions. The soil water pHs in the polluted regions are the strong acid(pH3.4-4.2) and buffer capacity of the polluted soil is low because canons such as $Na^+$, $K^+$, $Mg^{+2}$are leached by the acidification.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.3 s.94
• /
• pp.253-259
• /
• 2005

In this paper, BaSrTiO$_{3}$(BST) thin film tunable interdigital capacitor using low cost silicon substrate instead of expensive single-crystalline substrate is presented. The tunable capacitor in which BST thin film is deposited by PLD has operation frequency and applied bias up to 4 GHz and 50 V, respectively. The maximum tunability in capacitance is found to be 30$\%$, for an applied field of 5 kV/cm at a bias of 50 V. Therefore, it has been shown that the BST microwave tunable capacitor can be integrated onto Si substrate.

• Journal of the Korean Ceramic Society
• /
• v.40 no.4
• /
• pp.350-353
• /
• 2003

Millimeter-wave dielectric ceramics have been used like applications for ultrahigh speed wireless LAN because it reduces the resources of electromagnetic wave, and Intelligent Transport System (ITS) because of straight propagation wave. For millimeterwave, the dielectric ceramics with high quality factor (Q$.$f), low dielectric constant($\varepsilon$), and nearly zero temperature coefficient of resonant frequency ($\tau$) are needed. No microwave dielectric ceramics with these three properties exist except Ba(Mg$\_$1/3/Ta/sub1/3/)O$_3$ (BMT), which has a little high s: In this paper, alumina (Al$_2$O$_3$) and fosterite (Mg$_2$SiO$_4$), candidates for millimeter-wave applications, were studied with an objective to get high q$.$f and nearly zero $\tau$$\_$f/ For alumina ceramics, q$.$f more than 680,000 GHz was obtained but it was difficult to obtain nearly zero Qf. On the other hand, for forsterite ceramics, q$.$f was achieved from 10,000 GHz of commercial for sterite to 240,000 GHz of highly purified MgO and SiO$_2$ raw materials, and $\tau$$\_$f/ was reduced a few by adding TiO$_2$ with high positive $\tau$$\_$f/.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.319-319
• /
• 2013

Even though the fabrication methods of metal oxide based thin film capacitor have been well established such as RF sputtering, Sol-gel, metal organic chemical vapor deposition (MOCVD), ion beam assisted deposition (IBAD) and pulsed laser deposition (PLD), an applicable capacitor of printed circuit board (PCB) has not realized yet by these methods. Barium Strontium Titanate (BST) and other high-k ceramic oxides are important materials used in integrated passive devices, multi-chip modules (MCM), high-density interconnect, and chip-scale packaging. Thin film multi-layer technology is strongly demanded for having high capacitance (120 nF/$mm^2$). In this study, we suggest novel multi-layer thin film capacitor design and fabrication technology utilized by plasma assisted deposition and photolithography processes. Ba0.6Sr0.4TiO3 (BST) was used for the dielectric material since it has high dielectric constant and low dielectric loss. 5-layered BST and Pt thin films with multi-layer sandwich structures were formed on Pt/Ti/$SiO_2$/Si substrate by RF-magnetron sputtering and DC-sputtering. Pt electrodes and BST layers were patterned to reveal internal electrodes by photolithography. SiO2 passivation layer was deposited by plasma-enhanced chemical vapor deposition (PE-CVD). The passivation layer plays an important role to prevent short connection between the electrodes. It was patterned to create holes for the connection between internal electrodes and external electrodes by reactive-ion etching (RIE). External contact pads were formed by Pt electrodes. The microstructure and dielectric characteristics of the capacitors were investigated by scanning electron microscopy (SEM) and impedance analyzer, respectively. In conclusion, the 0402 sized thin film multi-layer capacitors have been demonstrated, which have capacitance of 10 nF. They are expected to be used for decoupling purpose and have been fabricated with high yield.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.4C no.2
• /
• pp.64-67
• /
• 2004

In this paper, to discover the brightness improvement of ZnS:Cu powder electroluminescence (EL), a new structure is proposed in which phosphor and dielectric are mixed between electrodes. Dielectric and phosphor material are BaTiO$_3$ and ZnS:Cu, respectively. The effect of the mixed layer on EL sample is considered the improvement of source efficiency. Although the number of electrons introduced into the phosphor increases only modestly, the high electric field region of phosphor grains increases comparatively in the characteristics of brightness-voltage. Furthermore, the relaxation occurs through leading and trailing edge pairs, which is relatively efficient in characteristics of decay time. With these results, we found that the brightness of newly proposed ZnS:Cu powder electroluminescence was 167.24 cd/$m^2$ at ac voltage of 100V and frequency of 400Hz.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1526-1528
• /
• 1999

In this papaer, 7-segment was implemented using AC powder EL. ZnS:Cu and $BaTiO_3$ was used as a phosphor and dielectric respectively. The preparation of phosphor and dielectic layer was performed with screen printing. The implemented system of 7-segment was divided as following; EL display. driving circuit. software for driving. The properties of fabricated devices was measured with EL spectrum. brightness and J-V.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.182-182
• /
• 2009

The effect of Re-oxidation on the PTCR properties of Sm-doped barium titanate ceramics was investigated by means of impedance spectroscopy. Electrical properties such as resistance vs. temperature, I-V curve were measured and microstructure was observed with SEM photography. Sample was fabricated with thick film process such as tape casting of green sheet, screen printing of electrode pattern, stacking, firing in reduced atmosphere and re-oxidation, etc. As the temperature of re-oxidation increases, resistance jump as a function of temperature enhances but resistance at room temperature increases. These behavior of resistance as a function of temperature, dependent on the re-oxidation condition, is analyzed with Cole-Cole impedance plot and is shown to be related with the degree of oxidation of grain boundary regardless of grain core during re-oxidation process of sample.