• Proceedings of the KIEE Conference
• /
• 1996.07b
• /
• pp.850-852
• /
• 1996

High impedance fault (HIF) is defined as fault that general overcurrent relay can't detect or interrupt, Especially when HIF occur under 15 kV, energized high voltage conductor results in fire hazard, equipment damage or personal threat. Because most HIF occur arc, HIF detection using arc is to increase. Numerical arc model can be applied in an electromagnetic transients program (EMTP) to reproduce the dynamic and random characteristic of arcs for any insulator arrangement, current and system voltage. It allows the representation of any network configuration to be investigated, so the digital simulation of arc faults through air can be substitute for demanding power arc test.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1867-1869
• /
• 2003

In this paper, chamber(Circuit breaker compartment of C-GIS) made of stainless steel with 4 mm width is used. Artificial defect was made on enclosure or HV conductor of chamber and $SF_6$ gas was injected into it according to pressure. In this experiment, Acoustic emission sensors of different types was used to compare sensitivity to detect acoustic signal occurred by Partial discharge(PD) of according to types and resonance frequency in $SF_6$ gas atmosphere. Sensors used in tests was R6I, R15I and 2/4/6 Pre-Amplifier connected with R6IU without pre. amp. In case of R6IU, gain was adjusted with 40 dB like other sensors and operated by differential mode. Post amplifier(post. amp) and band pass filter(BPF) were developed Gain of post. amp. is 60 dB and BPF has band width of $50{\sim}300$ kHz. Also, envelope circuit developed reduces frequency of AE sensor. As a result, in $SF_6$ atmosphere, R6IU and R6I had resonance frequency of 60 Hz was better than R15I. Also, R6IU was better than R6I because of type property of pre.amp. had differential mode.

• Economic and Environmental Geology
• /
• v.9 no.4
• /
• pp.225-240
• /
• 1976

This study deals with the flow of bed rock ground water of Banyaweol Formation, which is presently cleared up as a laminar flow. The result obtained may be summarized as the following. 1) The Banyaweol Formation consists mainly of thin-bedded, green to blackish green shale, mudstone, and marl. The marl and mudstone alternatively occur with shale. The marl and mudstone form a aquifer of Banyaweol Formation. In this study, a group of aquifer is in convenience named as a aquifer zone. The aquifer occurs in lenticular form. The aquifer seems to be a type of artesian aquifer because it is covered with aquicludes, but it actually forms a unconfined aquifer because its piezometric surface stays under the lower aquiclude. The lowering of piezometric level is formed because of leakage of the ground water to the lower aquifer undersaturated. 2) The coefficient of permeability of Banyaweol Formation's ground water body (K) is derived by using Dupuit's equation as the following ${\log}K=\frac{CK^2-dK+f}{aK-b}\;\(M=1.365(2H-s)s\\M={\log}1.956s{\sqrt{H}}r\)$ here, $$a=\sum_{1}M_iG_i$$ $$b={\frac{1}{2}log{\sum_{i}}Q_i{^2}$$ $$c=2{\sum_{i}}M_i{^2}$$ $$d=loge{\sum_{i}}M_{i}Q_{i}+2{{\sum_{i}}N_{i}Q_{i}$$ $$f=loge{\sum_{i}}Q_i{^2}N_i$$ If the measured values substituted for the above equation, the coefficient of permeability of the aquifer is 4.1m/day. The coefficient of storge of the aquifer is $2.8{\times}10^{-4}$ if the measured values substituted for Theis's equation. Using the above constants, the filtration velocity of the aquifer is $2.1{\times}1O^{-1}m/day$and the daily flow quantity of the ground water is $847.38m^{3}/day$. 3) In order to understand the time necessary for a circulation of ground water body, the contents of tritum contained in the ground water are measured as 2.3 T.U. at the Korea Atomic Energy Research Institute. Before 1952, the average concentration of tritium per year in groundwater was reported as 10T. u., taking it as the standard, the groundwater of the present study 26.25 years old. Therofore, the groundwater of the Banyaweol Formation is judged as an relatively old groundwater. It is characteristic that the ground water of Banyawol Formation is laminar flow as well as unconfined aquifer and ground water flow of relatively long time. 4) The nature, means of flow, and circulation of Banyaweol Formation's ground water body make it possible set up this ground water body as a ground water system.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.6
• /
• pp.761-768
• /
• 1999

This paper is studied to find the optimum condition of double-inlet Sirocco fan installed in an indoor PAC for low noise operation by the Taguchi method. The goal of this study is to obtain the best combination of each control factor which results in a desired flowrate of Sirocco fan with minimum variability. In this study, the parameter design of the Taguchi method is adopted for robust design by the dynamic characteristic analysis using orthogonal arrays and S/N ratios. The flowrate measurements are conducted by using a multiple-nozzle-type fan tester according to the orthogonal array L9($3^4$). The results of this study can be summarized as follows ; (i) The optimum condition of control factor is a set of where A is an inner to outer diameter ratio($D_1/D_2$), B is a width to outer diameter ratio($L/D_2$), C is a blade attachment angle(${\theta}$) and D is a number of blade(Z), (ii) The flowrate under the optimum condition satisfies the equation $y=0.0384{\cdot}M$ where M is a signal factor, namely number of revolution. The flowrate performance improves about 7.3% more largely as compared with the current condition, which results in about 35RPM reduction of number of revolution for the target flowrate $18.5m^3/min$, and (iii) The sensitivity analysis shows that the major factors in contribution to flowrate performance are A, B, and D ; the percentage contributions of each control factor are 44.01%(Z), 26.77%($D_1/D_2$) and 20.42%($L/D_2$).

• Asian-Australasian Journal of Animal Sciences
• /
• v.22 no.3
• /
• pp.428-432
• /
• 2009

40 goat kid ribcages were held for 7 days in storage conditions ($4^{\circ}C$) and used to determine the effects of three different packaging methods (atmospheric air, vacuum and modified atmosphere package (MAP) 10:70:20 mixture of $N_2:O_2:CO_2$) on meat quality of the chops. L* was affected by the packaging method being lighter than MAP chops. The coordinate a* significantly increased during storage time. For MAP-packed chops and those kept in atmospheric air, b* increased markedly during storage time whereas it remained unaffected throughout storage when in vacuum packages. Final pH values ranged from 5.6 to 5.8 and no effects were found for either storage time or packaging method. WHC means were lowest for the three packaging methods on day 7 of storage and highest on day 1. Storage time increased water loss in vacuum treatments. Trained panel colour acceptability was lower at 3, 5 and 7 days than on day 1 of storage for atmospheric air treatment and vacuum packaging, while for the MAP treatment average values on days 5 and 7 were lower than those observed on days 1 or 3. Trained panel odour was lower for atmospheric air and vacuum packages at 3, 5, and 7 days storage than at 1 day, while no differences were found in trained panel odour acceptability for MAP packages. With reference to consumers, the MAP proposed in the present study is the chosen method for storing goat meat, rather than vacuum or atmospheric air packaging.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.73-76
• /
• 1998

We give pressure stimulation into organic thin films and detect the induced displacement current. then manufacture a device under the accumulation condition that the state surface pressure is 15[mN/m]. In processing of a device manufacture. We can see the process is good from the change of a surface pressure for organic thin films and transfer ratio of area per molecule. The structure of manufactured device is Au/organic thin films(polyimide)/Au, the number of accumulated layers are 31,35, and 41. I-V characteristic of the device is measured from 0[V] to +5[V]. The maximum value of measured current is increased as the number of accumulated layers are decreased. The resistance for the number of accumulated layers, the energy density for an input voltage show desired results, and the insulation of a thin film is better as the interval between electrodes is larger.

• Proceedings of the KIEE Conference
• /
• 2001.11a
• /
• pp.219-223
• /
• 2001

In this paper, electromagnetic waves were measured in accordance with propagating the discharge when positive and negative DC high voltage was applied to needle-plane electrdes and plane-plane electrdes that solid dielectric was inserted between the electrodes. The radiated electromagnetic waves were investigated in bandwidth of VHF($30{\sim}230$[MHz]) using an biconical antenna. In needle-plane electrodes high electric field intensity is shown in both frequency band of 90(MHz) and 170[MHz], and gradually decreasing characteric is appeared at high frequency band. However high electric field intensity is shown in both 80[MHz] and 140[MHz] in case of plane-plane electrodes configuration. And over 150[MHz] frequency band, rapidly decreasing characteristic is shown. Moreover, electric field intensity of positive DC is about $5{\sim}10$[dB] higher than negative DC.

• Journal of Hydrogen and New Energy
• /
• v.19 no.3
• /
• pp.199-208
• /
• 2008

HI decomposition was conducted using Pt/C-based catalysts with a fixed-bed reactor in the range of 573 K to 773 K. To examine the change of the characteristic properties of the catalysts, $N_2$ adsorption analyser, a X-ray diffractometer(XRD), and a scanning electron microscopy(SEM) were used before and after the HI decomposition reaction. the effect of Pt loading on HI decomposition was investigated by $CO_2$-TPD. HI conversion of all catalysts increased as decomposition temperature increased. The XRD analysis showed that the sizes of platinum particle became larger and agglomerated into a lump during the reaction. From $CO_2$-TPD, it can be concluded that the cause for the increase in catalytic activity may be attributed to the basic sites of catalyst surface. The results of both b desorption and gasification reaction showed the restriction on the use of Pt/C-based catalyst.

• Asian-Australasian Journal of Animal Sciences
• /
• v.27 no.11
• /
• pp.1638-1643
• /
• 2014

This study was conducted to compare carcass characteristics and physico-chemical meat quality in two different genotype ducks raised under identical feeding and rearing conditions. A total of ninety 1-d-old Korean native ducks (KND, n = 45) and commercial meat-type ducks (Grimaud, n = 45) were fed same experimental diets during 56 d and 42 d, respectively to obtain similar slaughter weights. The experimental diet for starter period contained 20% crude protein (CP) and 2,900 kcal nitrogen corrected true metabolizable energy (TMEn)/kg of diet and that for grower period contained 17% CP and 3,050 TMEn/kg of diet. Average daily gain and feed efficiency of KND were inferior to those of commercial meat-type ducks (p<0.05). Carcass weight was not different between two genetically different ducks, but carcass yield of KND was significantly higher (p<0.05) than that of commercial meat-type ducks. There were no significant differences in cooking loss and pH of breast meat between two genetically different ducks, but water holding capacity of KND was significantly higher than that of commercial meat-type ducks. The linoleic acid and total polyunsaturated fatty acid of breast meat from KND were significantly higher (p<0.05) than the corresponding part from commercial meat-type ducks. Significant differences were detected in water holding capacity and the content of linoleic acid and polyunsaturated fatty acid, which were significantly higher in KND, whereas growth performance tended to be superior in commercial ducks. At the market weight, the meat from KND was judged to have better qualities with regard to higher water holding capacity and greater content of polyunsaturated fatty acid compare with meat from commercial meat-type duck.

• Composites Research
• /
• v.30 no.2
• /
• pp.116-125
• /
• 2017

The purpose of this study is to develop silicon carbide fiber showing an excellent mechanical properties under highly oxidative conditions at high temperature. Polycarbosilane(PCS) as a preceramic precursor was used for making the SiC fiber. PCS fiber was taken by melt spinning method followed by melting the PCS at $300{\sim}350^{\circ}C$ in N2 gas. The Curing of PCS fiber was carried out in air oxygen chamber, prior to high temperature pyrolysis. Degree of cure was calculated by characteristic peak's ratio of Si-H to $Si-CH_3$ in FT-IR spectra before and after curing of PCS fiber. The properties of SiC fiber was affected greatly by the degree of cure. The SiC fiber produced by controlling fiber tension during heat treatment showed good properties. The SiC fiber exposed to $1000^{\circ}C$ at air from 1 min. up to maximum 50 hrs showed around 60% reduction in tensile strength. We found that large amount of carbon content on the fiber surface after long-term exposure has resulted in lower tensile strength.