• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.1 s.256
• /
• pp.50-54
• /
• 2007

Nickel nano and microstructures are fabricated with simple process. The fabrication process consists of nickel deposition, lithography, nickel ion etching and plasma ashing. Well-aligned nickel nanowalls and nickel self-encapsulated microchannels were fabricated. We found that the ion etching condition as a key fabrication process of nickel nanowalls and self-encapsulated microchannels, i.e., 40 sccm Ar flow, 550 W RF power, 15 mTorr working pressure, and $20^{\circ}C$ water cooled platen without using He backside cooling unit and with using it, respectively. We present the experimental results and discuss the formational conditions and the effect of nickel redeposition on the fabrication of nickel nano and microstructures.

• Journal of Adhesion and Interface
• /
• v.8 no.1
• /
• pp.15-27
• /
• 2007

Polyimide (PI) surface modification was carried out by ion-beam treatment and silane-imidazole coupling agent to improve the adhesion between polyimide film and copper. Silane-imidazole coupling agent contains imidazole functional groups for the formation of a complex with copper metal through a coordination bonding and methoxy silane groups for the formation of siloxane polymers. The PI film surface was first treated by argon (Ar)/oxygen ($O_2$) ion-beam, followed by dipping it into a modified silane-imidazole coupling agent solution. The results of X-ray photoelectron spectroscopy (XPS) spectra revealed that the $Ar/O_2$ plasma treatment formed oxygen functional groups such as hydroxyl and carbonyl groups on the polyimide film surface and confirmed that the PI surface was modified by a coupling reaction with imidazole-silane coupling agent. Adhesion between copper and the treated PI film by ion-beam and coupling agent was superior to that with untreated PI film. In addition, adhesion of PI film treated by an $Ar/O_2$ plasma to copper was better than that of PI film treated by a coupling agent. The peeled-off layers from the copper-PI film joint were completely different in chemical composition each other. The layer of PI film side showed similar C1s, N1s, O1s spectra to the original Upilex-S and no Si and Cu atoms appeared. On the other hand the layer of copper side showed different C1s and N1s spectra from the original PI film and many Si and Cu atoms appeared. This indicates that the failure occurs at an interface between the imidazole-silane and PI film layers rather than within the PI layers.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.3
• /
• pp.494-503
• /
• 1997

We investigated the initial stages of formation of the Cu/polyimide interface using another two methods by X-ray photoelectron spectroscopy. : One, in-situ measurement with increasing of Cu deposition thickness onto polyimide(PI), the other, measurement with decreasing of Cu thickness of Cu/pI film by $Ar^+$ ion etching. From these results, we find that the chemical reactions exist in Cu/PI interface. However, the measured chemical reactions were different according to experimental method.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.6
• /
• pp.346-350
• /
• 2015

In this study, we carried out an investigation of the etch characteristics of TiO₂ thin films and the selectivity of TiO₂ to SiO₂ in adaptive coupled C1₂/Ar plasma. The maximum etch rate of the TiO₂ thin film was 136±5 nm/min at a gas mixing ratio of C1₂/Ar (75%:25%). The X-ray photoelectron spectroscopy (XPS) analysis showed the efficient destruction of oxide bonds by the ion bombardment as well as the accumulation of low volatile reaction products on the etched surface.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.3
• /
• pp.133-136
• /
• 2004

Low-Pressure inductively coupled RF discharge sources have important industrial applications mainly because they can provide a high-density electrodeless plasma source with low ion energy and low power loss. In an inductive discharge, the RF power is coupled to the plasma by an electromagnetic interaction with the current flowing in a coil. In this paper, the experiments have been focussed on the electric characteristic and carried out using a single Langmuir probe. The internal electric characteristics of inductively coupled Ar RF discharge at 13.56(MHz) have been measured over a wide range of power at gas pressure ranging from 1∼70(mTorr).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.340-340
• /
• 2010

본 연구에서는 유도결합형 플라즈마(ICP)를 이용하여, HBr/Ar 가스의 조성비 변화에 따른 Pb(Zr,Ti)$O_3$ 박막에 대한 식각특성을 연구 하였다. PZT박막의 식각속도와 Oxide($SiO_2$), Photo resister(PR)에 대한 식각선택비를 추출하였으며, 식각 메카니즘을 규명하기 위하여 optical emission spectroscopy(OES)와 double Langmuir prove(DLP) 이용하여 라디칼 특성변화와 이온 전류밀도(Ion current density)를 측정하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.384-384
• /
• 2010

The surface reaction characteristics of Zinc Oxide (ZnO) in $Cl_2/BCl_3$/Ar gas ratio using inductively coupled plasma system were investigated. It was found that ZnO etch rate shows a non-monotonic behavior with increasing both Ar fraction in $Cl_2/BCl_3$ plasma, RF power, and gas pressure. The maximum ZnO etch rate of 53 nm/min was obtained for $Cl_2$(3 sccm)/$BCl_3$(16 sccm) /Ar(4 sccm) gas mixture. The chemical state of etched surfaces was investigated with X-ray diffraction (XRD) and the etched surface was investigated to the rms by atomic force microscopy (AFM). From these data, the suggestions on the ZnO etch mechanism were made by secondary ion mass spectrometery (SIMS).

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.844-847
• /
• 2001

The application of laser direct etching has been discussed, and believed that the process is a very powerful method for micro machining. This study is focused on the micro patterning technology using laser direct etching process with no chemical damage of the material surface. A new introduced concept of energy synergy effect for surface micro machining is the combination of chemically ion reaction and laser thermal process. The etchant can't etch the material in room temperature, and used Ar laser has not power enough to machine. But, the machining is occurred in local area of the material by the combined energy. Using this process, the material is especially prevented from chemical damage for electric property. We have tested this new concept, and achieved a line with $1{mu}m$ width. The Ar laser with 488nm wavelength was used. The material was Si(100) wafer, and etchant is KOH solution. The application and flexibility of this process is in great hopes for MEMS structures and fabrication of the micro electric device parts.

• Applied Science and Convergence Technology
• /
• v.23 no.4
• /
• pp.179-186
• /
• 2014

Fluid model based numerical simulation was carried out for an inductively coupled plasma assisted sputter deposition system. Power absorption, electron temperature and density distribution was modeled with drift diffusion approximation. Effect of an electrically conducting substrate was analyzed and showed confined plasma below the substrate. Part of the plasma was leaked around the substrate edge. Comparison between the quasi-neutrality based compact model and Poisson equation resolved model showed more broadened profile in inductively coupled plasma power absorption than quasi-neutrality case, but very similar Ar ion number density profile. Electric potential was calculated to be in the range of 50 V between a Cr rod source and a conductive substrate. A new model including Cr sputtering by Ar+was developed and used in simulating Cr deposition process. Cr was modeled to be ionized by direct electron impact and showed narrower distribution than Ar ions.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1704-1706
• /
• 2003

Low-Pressure inductively coupled RF discharge sources have important industrial applications mainly because they can provide a high-density electrodeless plasma source with low ion energy and low power loss. In an inductive discharge, the RF power is coupled to the plasma by an electromagnetic interaction with the current flowing in a coil. In this paper, the experiments have been focussed on the electric characteristic and carried out using a single Langmuir probe. The internal electric characteristics of inductively coupled Ar RF discharge at 13.56 [MHz] have been measured over a wide range of power at gas pressure ranging from $1{\sim}70$ [mTorr].