• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.259-262
• /
• 2009

The influence of pre-strain in low-cycle fatigue behavior of Fe-18Mn-0.05Al-0.6C TWIP steel was studied by conducting axial strain-controlled tests. As-received plates were deformed by rolling with reduction ratios of 10 and 30%, respectively. A triangular waveform with a constant frequency of 1 Hz was employed for low cycle fatigue test at the strain amplitudes in the range of ${\pm}0.4{\sim}{\pm}0.6$ pct. The results showed that low-cycle fatigue life was strongly dependent on the amount of pre-strain as well as the strain amplitude. Increasing the amount of prestrain, the number of reversals to failure was significantly decreased at high strain amplitudes, but the effect was negilgible at low strain amplitudes. A new model for predicting fatigue life of pre-strained body has been devised adding a correction term of ${\Delta}E_{pre-strain}$ to the energy-based fatigue damage parameter.

• 자원환경지질
• /
• 제36권2호
• /
• pp.111-121
• /
• 2003

이 연구의 목적은 영월, 정선 및 평창지역에 분포하는 13개 석탄광에서 배출되는 산성광산배수의 물리화학적 특성파악을 통하여 주변 수계에 미치는 영향을 조사하는 것이다. 2000년 11월부터 2002년 7월까지 총 6회의 시료를 채취하여, pH, Eh, TDS, salinity, DO 등의 물리화학적 특성은 물론 Al, Ca, Fe, Mg, Mn, Zn 등을 포함한 총 18개의 양이온, 질산염과 황산염을 포함한 6개의 음이온의 한량을 각각 ICP-AES와 IC를 이용하여 분석하였다. 조사대상 지역이 광역적이고 수계가 서로 다르기 때문에 총 4개의 수계로 구분하여 조사한 결과, '수계 1'에 해당하는 삼척탄좌 정암광업소에서 유출되는 물이 가장 전형적인 산성광산배수의 특징인 낮은 pH (3～4)와 높은 TDS (1,000-5,000 ㎎/1) 값을 보이고 있었으며, 이들에 의해 주변 수계가 상당한 영향을 받고 있었다 양이온 분석결과, 일부 광산에서는 비오염지역의 수계에서 검출되는 중금속에 비해 수십에서 수백 배 높은 함량이 검출되었다. 특히, Al, Fe, Mn 및 Zn 등은 상당히 부화되어, 정암광업소에서 유출되는 산성수에서는 각각 350 mg/1의 Al, 80 mg/1의 Fe, 44 mg/1의 Mn 및 8 mg/1의 Zn이 검출되었다. 서진광산, 세방광산 및 성진광산 둥에서도 50 mg/1 이상의 Al과 100 mg/1 이상의 Fe 및 l0 mg/l 이상의 Mn 등이 검출되어 이들에 의한 수계 오염 가능성이 확인되었다. 음이온의 분석 결과에 의하면, 대부분의 조사대상광산에서 200 mg/1 이상의 황산염이 검출되었으며 일부 광산 유출수에서는 100 mg/1 이상의 황산염이 검출되었다. 또한 산성광산배수의 계절적인 변화를 고찰하기 위해 계절별로 시료를 채취하여 조사한 결과, 건기에 비해 우기에 일부 금속과 황산염의 농도가 증가되는 경향을 보였다. 결과적으로, 조사대상지역의 수계는 석탄광 개발로 인해 발생된 산성광산배수에 의해 중금속 및 일부 음이온으로 오염되어 있으며, 따라서 이를 위한 적절한 처리 시설의 설치와 관리가 요구된다.

• 소성∙가공
• /
• 제29권3호
• /
• pp.135-143
• /
• 2020

Low-cost alloying elements were added to a modified Al-6.5Si alloy and its microstructure, tensile and impact toughness properties were investigated. The alloying elements added were Mg, Zn, and Cu, and two kinds of alloy A (Mg:0.5, Zn:1, Cu:1.5 wt.%) and alloy B (Mg:2, Zn:1.5, Cu:2 wt.%) were prepared. In the as-cast Al-6.5Si alloys, Si phases were distributed at the dendrite interfaces, and Al₂Cu, Mg₂Si, Al₆ (Fe,Mn) and Al₅ (Fe,Mn)Si precipitates were also observed. The size and fraction of casting defects were measured to be higher for alloy A than for alloy B. The secondary dendrite arm spacing of alloy B was finer than that of alloy A. It was confirmed by the JMatPro S/W that the cooling rate of alloy B could be more rapid than alloy A. The alloy B had higher hardness and strength compared to the values of alloy A. However, the alloy A showed better impact toughness than alloy B. Based on the above results, the deformation mechanism of Al-6.5Si alloy and the improving method for mechanical properties were also discussed.

• 한국환경과학회지
• /
• 제9권4호
• /
• pp.325-330
• /
• 2000

The hydroxyapatite (HAp) for the present study was prepared by precipitation method in semiconductor fabrication and the crystallized at ambient to 95$0^{\circ}C$ for 30min in electric furnace. The ion-exchange characteristics of HAp for various heavy metal ions such as $Cd^{2+}, Cu^{2+}, Mn^{2+}, Zn^{2+}, Fe^{2+}, Pb^{2+}, Al^{3+}, and Cr^{6+}$ in aqueous solution has been investigated. The removal ratio of various metal ions for HAp were investigated with regard to reaction time, concentration of standard solution, amount of HAp and pH of solution. The order of the ions exchanged amount was as follws: $Pb^{2+}, Fe^{3+}>Cu^{2+}>Zn^{2+}>Al^{3+}>Cd^{2+}>Mn^{2+}>Cr^{6+}. The Pb^{2+}$ ion was readily removed by the Hap, even in the strongly acidic region. The maximum amount of the ion-exchange equilibrium for $Pb^{2+}$ ion was about 45 mg/gram of HAp. The HAp would seem to be possible agent for the removal of heavy metal ions in waste water by recycling of waste sludge in semiconductor fabrication.

• 대한환경공학회지
• /
• 제33권2호
• /
• pp.93-102
• /
• 2011

본 연구에서는 부산신항만 준설퇴적물에 포함된 중금속의 총농도, 이동성, 생체이용률, 독성을 알아보기 위하여 총함량분석과 연속추출실험을 실시하였다. 준설퇴적물의 중금속 총농도는 다음과 같이 비교적 낮았다: Al (2.36~2.96 wt.%), As (1.6~3.3 mg/kg), Ba (30.0~33.8 mg/kg), Cd (0.12~0.18 mg/kg), Cr (27.5~35.0 mg/kg), Cu (11.3~15.0 mg/kg), Fe (2.91~3.51 wt.%), Mn (324~408 mg/kg), Ni (18.8~23.8 mg/kg), Pb (23.8~31.3 mg/kg), Zn (70.0~86.3 mg/kg). 또한 대부분의 중금속이 residual fraction으로 존재하였는데, 이는 오염원이 자연발생적일 가능성이 높음을 의미한다: Al (87.5~95.9%), As (74.1~93.8%), Ba (71.8~77.6%), Cr (69.5~94.3%), Cu (50.0~78.7%), Fe (70.8~87.6%), Ni (64.5~75.3%), Pb (53.4~64.3%), Zn (62.5~81.7%). 반면에 Cd과 Mn은 주로 non-residual fraction으로 존재했다. 준설퇴적물의 유해중금속 농도가 낮고 residual fraction 비율이 높기 때문에, 이를 벽돌, 도로포장재료 등으로 재활용하는 것이 가능하다고 사료된다.

• 한국자기학회지
• /
• 제16권6호
• /
• pp.276-278
• /
• 2006

스위칭 특성을 향상시키기 위하여 비정질 강자성 CoFeSiB 자유층을 갖는 자기터널접합 (MTJ)의 스위칭 특성을 연구하였다. 자기터널접합의 구조는 $Si/SiO_{2}/Ta$ 45/Ru 9.5/IrMn 10/CoFe 10/CoFe $7/AlO_{x}/CoFeSiB\;(t)/Ru\;60\;(nm)$이다. CoFeSiB는 $560\;emu/cm^{3}$의 낮은 포화자화도와 $2800\;erg/cm^{3}$의 높은 이방성 상수를 가졌다. 이러한 특성이 자기터널접합의 낮은 보자력($H_{c}$)과 높은 자장민감도를 갖게 한다. 이것은 또한 Landau-Lisfschitz-Gilbert 방정식에 근거한 미세자기 전산시뮬레이션을 통하여 submicrometersized elements에서도 확인하였다. CoFeSiB 자유층 두께를 증가함으로서 스위칭 특성은 반자화 자기장의 증가로 인하여 더욱더 나빠졌다.

• 한국광물학회지
• /
• 제27권2호
• /
• pp.97-105
• /
• 2014

일월탄광에는 산화조, SAPS, 소택지의 3단계 자연정화시설이 설치되어 있으며 갱내수를 모아 정화한 후 주변 하천으로 유출시키고 있다. 일월탄광 갱내수의 pH 값은 계절에 관계없이 2.28-2.42로 낮은값을 나타내지만 산화조를 거치는 동안 pH 값은 6.17-6.53 급격하게 증가한다. 정화시설에 의한 정화효율은 $SO_4$, Mg, Al, Ca, Mn은 각각 약 50%, 40%, 100%, 24%, 59%이다. 갱내수의 Fe는 아주 낮은 값($1.06-1.09mg/{\ell}$)이지만 정화시설을 거치는 동안 100%의 제거효율을 나타낸다. 이와 같이 일월탄광에 설치한 정화시설은 pH 상승과 Fe와 Al의 제거 효율은 높지만 $SO_4$, Mg, Ca, Mn 등은 60% 이하로 상대적으로 낮다. 따라서 이러한 이온을 제거하기 위해서는 다른 정화기술을 적용해야 할 것으로 판단된다. pH 2.28-2.42 범위인 갱내수가 유입되는 정화시설 바닥에 침전되는 침전물은 슈워트마나이트이며 ($Fe_8O_8(OH)_6SO_4$), pH 5.83-5.96인 침출수에서는 2-line 페리하이드라이트(2-line $Fe_2O_3{cdot}0.5H_2O$H2O)가 침전된다.

• 한국대기환경학회지
• /
• 제15권6호
• /
• pp.727-738
• /
• 1999

Total 76 aerosol samples were collected at Sungsan in Cheju Inland by high volume air sample for 1 year, from May 1995 to April 1996, and were analyzed for major elements(Na, Mg, Ca, Al, Fe) and trace elements(Mn, Co, Ni, Zn, Cd, Pb, U) by ICP/AES and ICP/MS. This study aims to determine the concentrations of trace metals and their seasonal variations in the atmosphere of Cheju Island, where is the remote area from pollution sources and also is the midway of transport of Asian continental materials into the western North Pacific. The concentrations of Na and Mg contributed by sea-salt aerosols were similar to those in the western part of Cheju island(Kosan) and in the western coast of Korea(Mallipo). They showed the highest value in summer and the lowest in spring and winter. Crustal metals(Al, Fe, Ca, Mn, Co, U) were 2~3 times lower than those of Mallipo. These metals showed the lowest values in summer and the highest in spring. Pollution-derived metals (Zn, Cd and Pb) were 2~4 times lower than those in Malipo. Some elemental ratios in aerosols grouped by three wind directions(north-northwest, east, and south-southwest) such as Fe/Al and Pb/Zn are presented as useful tracers indicating source areas, and their differentiation may be explained by geology and fuel types of source areas.

• 한국수소및신에너지학회논문집
• /
• 제5권2호
• /
• pp.99-109
• /
• 1994

To develop high capacity hydrogen storage alloys for secondary Ni/MH batteries, electrochemical charge/discharge characteristics of $Zr_{1-x}Ti_xMn_{1-y}V_yNi_{1-z}M_z$ (M=Al,Co,Fe) alloys were investigated, in which $0.2{\leq}x{\leq}0.6$, $0.2{\leq}y{\leq}0.8$, $0.2{\leq}z{\leq}0.4$. With increasing Ti content(x) and/or decreasing V content(y), lattice constants and maximum theoretical capacities of the alloys were decreased and equilibrium pressure of hydrogen absorption were increased. Electrochemical discharge capacities were increased with increasing Ti content(x). Especially, the alloys of x= 0.4~0.6 showed better charge/discharge efficiencies than those of x<0.4. Discharge capacities of $Zr_{0.4}Ti_{0.6}Mn_{0.4}V_{0.6}Ni_{0.8}Fe_{0.2}$, $Zr_{0.4}Ti_{0.6}Mn_{0.4}V_{0.6}Ni_{0.8}Al_{0.2}$ and $Zr_{0.5}Ti_{0.5}Mn_{0.4}V_{0.6}Ni_{0.6}Co_{0.4}$ were 385, 328 and 333mAh/g, respectively. These alloys were fully activated within five charge/discharge cycles and had a good charge and discharge rate capabilities and temperature characteristics.

• 한국주조공학회지
• /
• 제35권6호
• /
• pp.147-154
• /
• 2015

The effects of Sc and Sr elements on the modification of the eutectic $Mg_2Si$ phase and the castability were investigated in the Al-4wt%Mg-0.9wt%Si-0.3wt%Mn-0.15wt%Fe alloy. Measurements of the cooling curve and microstructure observations were performed to analyze the additional effects of Sc and Sr minor elements during the solidification process. A prominent effect found on the modification of the eutectic $Mg_2Si$ phase with additions of the Sr and Sc elements. Here, a fine eutectic $Mg_2Si$ phase and a decrease in the growth temperature of the eutectic $Mg_2Si$ phase were evident with an addition of Sc element up to 0.2 wt%. The growth temperature of the eutectic $Mg_2Si$ phase decreased and the effect on the modification of the eutectic $Mg_2Si$ phase increased with the addition of Sr element up to 0.02 wt%. The addition of 0.02wt%Sr had the strongest effect on the modification of the eutectic $Mg_2Si$ phase, and the resulting microstructure of the eutectic $Mg_2Si$ phase was found to have a fibrous morphology with a decreased aspect ratio and an increased modification ratio. Fluidity and shrinkage tests were conducted to evaluate the castability of the alloy. The addition of 0.02wt%Sr effectively increased the fluidity of the alloy, while an addition of Sc did not show any effect compared to when nothing was added. The maximum filling length was recorded for 0.01wt%TiB-0.02wt%Sr owing to the effect of the fine ${\alpha}$-Al grains. The macro-shrinkage ratio decreased, while the micro-shrinkage ratio increased with the addition of various eutectic modifiers. The highest ratio of micro-shrinkage was recorded for the 0.02wt%Sr condition. However, the total shrinkage ratio was nearly identical regardless of the amounts added in this study.