• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.37-40
• /
• 2003

Amorphous $Al_2O_3$ nanotubes have been fabricated by utilizing the ZnO nanowires as template with wet etching method. ZnO nanowires synthesized by thermal evaporation are conformally coated with $Al_2O_3$ by atomic-layer deposition(ALD) method. The $Al_2O_3$-coated ZnO nanowires are of core-shell structure; ZnO core nanowires and $Al_2O_3$ shells. When the $ZnO/Al_2O_3$ core-shell structure is dipped in $H_3PO_4$ solution at $25^{\circ}C$ for a 6 min, the core ZnO materials are completely etched, and only $Al_2O_3$ nanotubes are remained. This nanotube fabrication is technically easier than others, and simply approachable. Transmission electron microscopy shows that the $Al_2O_3$ nanotubes have various thicknesses that can be controlled.

• Clean Technology
• /
• v.28 no.2
• /
• pp.154-162
• /
• 2022

Microstructured Al@Al₂O₃ and Al@Ni-Al LDH (LDH = layered double hydroxide) core-shell metal-ceramic composites are prepared by hydrothermal reactions of aluminum (Al) metal substrates. Controlled hydrothermal reactions of Al metal substrates induce the hydrothermal dissolution of Al ions at the Al-substrate/solution interface and reconstruction as porous metal-hydroxides on the Al substrate, thereby constructing unique metal-ceramic core-shell composite structures. The morphology, composition, and crystal structure of the core-shell composites are affected largely by the ions in the hydrothermal solution; therefore, the critical physicochemical and surface properties of these unique metal-ceramic core-shell microstructures can be modulated effectively by varying the solution composition. A Ni/Al@Al₂O₃ catalyst with highly dispersed catalytic Ni nanoparticles on an Al@Al₂O₃ core-shell substrate was prepared by a controlled reduction of an Al@Ni-Al LDH core-shell prepared by hydrothermal reactions of Al in nickel nitrate solution. The reduction of Al@Ni-Al LDH leads to the exolution of Ni ions from the LDH shell, thereby constructing the Ni nanoparticles dispersed on the Al@Al₂O₃. The catalytic properties of the Ni/Al@Al₂O₃ catalyst were investigated for CO₂ methanation reactions. The Ni/Al@Al₂O₃ catalyst exhibited 2 times greater CO₂ conversion than a Ni/Al₂O₃ catalyst prepared by conventional incipient wetness impregnation and showed high structural stability. These results demonstrate the high effectiveness of the design and synthesis methods for the metal-ceramic composite catalysts derived by hydrothermal reactions of Al metal substrates.

• Korean Chemical Engineering Research
• /
• v.57 no.1
• /
• pp.111-117
• /
• 2019

This study proposed the fabrication and deposition of high purity crystalline $core-TiO_2/shell-Al_2O_3$ nanoparticles. Morphological properties of $core-TiO_2$ and coated $shell-Al_2O_3$ were confirmed by transmission electron microscope (TEM) and transmission electron microscope - energy dispersive spectroscopy (TEM-EDS). The electrical properties of the prepared $core-TiO_2/shell-Al_2O_3$ nanoparticles were evaluated by applying them to a working electrode of a Dye-Sensitized Solar Cell (DSSC). The particle size, growth rate and the main crystal structure of $core-TiO_2$ were analyzed through dynamic light scattering system (DLS), scanning electron microscope (SEM) and X-ray diffraction (XRD). The $core-TiO_2$, which has a particle size of 17.1 nm, a thin film thickness of $20.1{\mu}m$ and a main crystal structure of anatase, shows higher electrical efficiency than the conventional paste-based dye-sensitized solar cell (DSSC). In addition, the energy conversion efficiency (6.28%) of the dye-sensitized solar cell (DSSC) using the $core-TiO_2/shell-Al_2O_3$ nanoparticles selectively controlled to the working electrode is 26.1% higher than the energy conversion efficiency (4.99%) of the dye-sensitized solar cell (DSSC) using the conventional paste method.

• Korean Journal of Materials Research
• /
• v.15 no.12
• /
• pp.751-755
• /
• 2005

Fibrous $Al_2O_3-(m-ZrO_2)/t-ZrO_2$ composites having core/shell structure were fabricated by multi-extrusion process. The effect o volume fraction between core ($Al_2O_3-(m-ZrO_2)$) and shell ($t-ZrO_2$ was investigated to understand the relationship between microstructure and material properites, in which the volume fractions of core and shell were varied as 40:60, 50:50 and 60:40. The material properties o hardness and bending strength were increased as the volume fraction of core was increased, and their maximum values were about 1320 Hv and 750MPa, respectively. However, as the volume fraction of core increased, the values of relative density and fracture toughness were decreased from 97.1 to $96.5\%$ and from $6.5MPa{\cdot}m^{1/2}$ to $5.7MPa{\cdot}m^{1/2}$, respectively.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.11a
• /
• pp.11.1-11.1
• /
• 2009

Ternary Al2O3.ZrO2.Y2O3 samples with a eutecticcomposition were prepared by slow cooling. The microstructural evolution wasobserved with X-ray diffraction (XRD), scanning electron microscopy (SEM). TheSEM observation of the ternary samples agreed with the XRD with a completion ofcrystallisation by slow cooling. The target materials commonly have 'cantaloupe skin' microstructures as shown inthe previous studies by Han et al. The nanocomposite may have experienceddifferent cooling rates with two different microstructures, near the surfacehaving experienced optimal conditions for the eutectic reaction during theircooling and thus formed the eutectic microstructure, near the centre havingexperienced a slower cooling rate. The crystallised eutectic ternary Al2O3.ZrO2.Y2O3 system had three different phaseswith a 3Y2O3. 5Al2O3 (yttrium.aluminiumgarnet phase), an alumina phase formed by the eutectic reaction, and a solidsolution of ZrO2 and Y2O3.

• Journal of the Korean Ceramic Society
• /
• v.37 no.2
• /
• pp.117-121
• /
• 2000

Er-doped sodiumborosilicate glass films for waveguides amplifier were fabricated by Aerosol Flame Deposition(AFD) method. Al2O3 was added to sodium borosilicate glass films to suppress the formation of crystalline phase and control the refractive index. the formation of crystalline phase was suppressed above Al2O3 of 6 wt%. As the amount of Al2O3 increased from 2 to 12 wt% the refractive index of glass films increased lineary from 1.4595 up to 1.4710. After the core of 77SiO2-15B2O3-8Na2O＋6 wt%Al2O3＋8wt%Er2O3 was coated on the buffer layer of 77SiO2-15B2O3-8Na2O＋6 wt%Al2O3, the core was etched by reactive ion etching. The absorption spectrum of 3 cm waveguide amplifier showed two peaks of 1530 and 1550 nm.

• Clean Technology
• /
• v.21 no.1
• /
• pp.68-75
• /
• 2015

In this study, we investigated the structure and properties of a highly heat conductive metal-ceramic core-shell CoAl₂O₄@Al micro-composite for heterogeneous catalysts support. The CoAl₂O₄@Al was prepared by hydrothermal surface oxidation of Al metal powder, which resulted in the structure with a high heat conductive Al metal core encapsulated by a high surface area CoAl₂O₄ shell. For comparison, CoAl₂O₄ was also prepared by co-precipitation method and also utilized for a catalyst support. Rh catalysts supported on CoAl₂O₄@Al and CoAl₂O₄ were prepared by incipient wetness impregnation and characterized by N₂ adsorption, X-ray diffraction (XRD), scanning electron microscopy (SEM), CO chemisorption, and temperature-programmed reduction (TPR). The properties of catalysts were investigated for glycerol steam reforming reaction for hydrogen production at 550 ℃. Rh/CoAl₂O₄@Al exhibited about 2.8 times higher glycerol conversion turnover frequency (TOF) than Rh/CoAl₂O₄ due to facilitated heat transport through the core-shell structure. The CoAl₂O₄@Al and CoAl₂O₄ also showed some catalytic activities due to a partial reduction of Co on the support, and a higher catalytic activity was also found on the CoAl₂O₄@Al core-shell than CoAl₂O₄. These catalysts, however, displayed deactivation on the reaction stream due to carbon deposition on the catalysts surface.

• Korean Chemical Engineering Research
• /
• v.52 no.2
• /
• pp.209-213
• /
• 2014

A graft copolymer of poly(vinyl chloride)-g-poly(oxyethylene methacrylate) (PVC-g-POEM) was synthesized via atom transfer radical polymerization (ATRP) and used as a structure-directing agent to prepare $Al@Fe_2O_3$ core-shell nanocomposites through a sol-gel process. The amphiphilic property of PVC-g-POEM allows for good dispersion of Al particles and leads to specific interaction with iron ethoxide, a precursor of $Fe_2O_3$. Secondary bonding interaction in the sol-gel composites was characterized by Fourier transform-infrared (FT-IR) spectroscopy. The well-organized morphology of $Al@Fe_2O_3$ core-shell nanocomposites was observed using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Energy dispersive X-ray (EDX) and X-ray diffraction (XRD) were used to analyze the elemental composition and crystallization structure of the composites.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.117-117
• /
• 2013

염료감응태양전지의 효율을 높이기 위해서, 광전극으로 쓰이는 다공성 $TiO_2$ 후막에 플라즈마원자증착기술(PEALD)과 원자증착기술(ALD)을 이용하여 알루미나($Al_2O_3$)막을 3차원적으로 균일하고 매우 얇게 형성하였다. 이를 통해서 태양빛에 의해 여기된 염료의 전자가 알루미나를 통과(tunneling)하여 $TiO_2$ 전도대로 도입되게 함과 동시에 $TiO_2$ 전도대로 도입된 전자들이 전해질과 염료로 재결합하는 현상을 방지하였다. 결국 이러한 작용에 의해서 염료감응태양전지의 개방전압을 높이는 효과를 관측하였다. 나아가 PEALD와 ALD 두가지 방식으로 형성된 $Al_2O_3$ 껍질층의 특성 차이를 비교 관찰하고 이에 따른 염료감응태양전지의 소자 특성에 미치는 영향을 고찰하였다.

• The Journal of Advanced Prosthodontics
• /
• v.5 no.4
• /
• pp.382-387
• /
• 2013

PURPOSE. Although several surface treatments have been recently investigated both under in vitro and in vivo conditions, controversy still exists regarding the selection of the most appropriate zirconia surface pre-treatment. The purpose of this study was to evaluate the effect of alumina (Al) and aluminium nitride (AlN) coating on the shear bond strength of adhesive resin cement to zirconia core. MATERIALS AND METHODS. Fifty zirconia core discs were divided into 5 groups; air particle abrasion with 50 ${\mu}m$ aluminum oxide particles ($Al_2O_3$), polishing + Al coating, polishing + AlN coating, air particle abrasion with 50 ${\mu}m$ $Al_2O_3$ + Al coating and air particle abrasion with 50 ${\mu}m$ $Al_2O_3$ + AlN coating. Composite resin discs were cemented to each of specimens. Shear bond strength (MPa) was measured using a universal testing machine. The effects of the surface preparations on each specimen were examined with scanning electron microscope (SEM). Data were statistically analyzed by one-way ANOVA (${\alpha}$=.05). RESULTS. The highest bond strengths were obtained by air abrasion with 50 ${\mu}m$ $Al_2O_3$, the lowest bond strengths were obtained in polishing + Al coating group (P<.05). CONCLUSION. Al and AlN coatings using the reactive magnetron sputtering technique were found to be ineffective to increase the bond strength of adhesive resin cement to zirconia core.