• 한국세라믹학회지
• /
• 제47권4호
• /
• pp.325-328
• /
• 2010

Varying quantities of a high-thermal-expansion glass, 50CaO-20ZnO-$20B_2O_3-10SiO_2$ (CZBS), were added to alumina and sintered at $875^{\circ}C$ for 2 h for low temperature co-firing ceramic (LTCC) applications. As the amount of glass addition increased from 40 wt% to 70 wt%, the apparent density of the sintered product increased from 88.8% to 91.5%, which was also qualitatively confirmed by microstructural observation. When the glass addition was very high, e.g., 70 wt%, an apparent formation of secondary phases such as $CaZn_2AlZnSiAlO_7$, $Ca_2Al(AlSi)O_7$, $Ca_2Al_2SiO_7$, $Ca_2ZnSi_2O_7$ and ZnO, was observed. Both the dielectric constant and the coefficient of thermal expansion increased with the glass addition, which was qualitatively consistent with the analytical models, while the experimental values were lower than the predicted ones due to the presence of pores and secondary phases.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.387-390
• /
• 2000

The $Al_2$O$_3$specimens were prepared by the conventional mixed oxide method with addition La$_2$O$_3$, Bi$_2$O$_3$. The specimens were sintered at 15$25^{\circ}C$, 5hr., in air. The structural properties of the specimens were investigated by XRD and SEM. The $Al_2$O$_3$ceramics with dopants had hexagonal structure and didn't show secondary phases. In the case of specimens with 0.25wt% La$_2$O$_3$and 0.25wt% Bi$_2$O$_3$bulk densities and lattice parameter of c/a were 3.818g/cm$^3$, 3.783g/cm$^3$and ca=2.725, c/a=2.723, respectively. The bulk densities of $Al_2$O$_3$ceramics were decreased with dopants.

• 한국세라믹학회지
• /
• 제53권6호
• /
• pp.635-640
• /
• 2016

Electrical behavior of AlN ceramics sintered with $Y_2O_3$ as a sintering aid has been investigated with respect to additional $TiO_2$ dopant. From the impedance spectroscopy, it was found that the grain and grain boundary conductivities have greatly decreased with addition of $TiO_2$ dopant. The $TiO_2$ dopant also increased the activation energy of the grain conductivity by about 0.37 eV; this increase was attributed to the formation of an associate between Al vacancies and Ti ions at the Al sites. Similarly, the electronic conductivity was reduced by $TiO_2$ addition. However, $TiO_2$ solubility in AlN grains was below the detection limit of typical EDX analysis. Grain boundary was clean, without liquid films, but did show yttrium segregation. The transference number of ions was close to 1, showing that AlN is a predominantly ionic conductor. Based on the observed results, the implications of using AlN applications as insulators have been discussed.

• 한국세라믹학회지
• /
• 제18권2호
• /
• pp.112-118
• /
• 1981

A study was made on the processing of domestic blast furnace slag by flotation and chemical purification for the use of slag as a raw material in making soda lime glasses. Feasibility study has been made for the use of reprocessing slag as a source material for both coloring and chemical components (such as CaO, $Al_2O_3$, MgO and etc.) in the glass making process. Chemical composition of chemically purified slags ranges; $SiO_2$ 34.5~37.5, $Al_2O_3$, 16.2~14.1, $Fe_2O_3$ 0.33~0.14, CaO 34.5~38.8, MgO 4.0~5.2, NmO 0.16~0.39, $TiO_2$ 0.23~0.35, S 0.08~0.42, ignition loss 3.3~8.4 and others 0.48~0.51%. It was found that either amber or greenish color could be easily obtained with the addition of salg up to 24%, however the slag addition to glass batches much impaired the transmitancy of glass products, thus a glass made with 7% slag addition showed 82% in transmitancy value at 510 nm.

• Bulletin of the Korean Chemical Society
• /
• 제34권8호
• /
• pp.2461-2465
• /
• 2013

Pd-$Ce/{\gamma}-Al_2O_3-TiO_2$ catalysts were prepared by combined sol-gel and impregnation methods. Transmission electron microscopy, X-ray diffraction, $H_2$-temperature-programmed reduction, $O_2$-temperature-programmed desorption, and ethanol oxidation experiments were conducted to determine the properties of the catalysts. Addition of an optimal amount of Ce improved the performance of the $Pd/{\gamma}-Al_2O_3-TiO_2$ catalyst in promoting the complete oxidation of ethanol. The catalyst with 1% Ce exhibited the highest activity, and catalyzed complete oxidation of ethanol at $175^{\circ}C$; its selectivity to $CO_2$ reached 87%. Characterization results show that addition of appropriate amount of Ce could enrich the PdO species, and weaken the Pd-O bonds, thus enhancing oxidation ability of the catalyst. Meanwhile, the introduction of $CeO_2$ could make PdO better dispersed on ${\gamma}-Al_2O_3-TiO_2$, which is beneficial for the improvement of the catalytic oxidation activity.

• 한국재료학회지
• /
• 제10권5호
• /
• pp.321-327
• /
• 2000

다공성 알루미나 소결체내부로 3Y-TZP 및 12Ce-TZP 전구체를 각각 액상침투시킴으로써 2종류의 $Al_2O_3/TZP$복합체를 제조하였다. 소량의 (~11.0 wt%) TZP의 첨가는 Al2O3소결체 ($1600^{\circ}C$, 2시간)의 강도 (19~59%)와 파괴인성(14~157%)을 증가시켰다. 3Y-TZP의 첨가는 복합체의 강도의 향상에 12Ce-TZP의 첨가는 인성의 향상에 보다 효과적이었다. 침투도니 TZP는 복합체의 내부보다 표면에 집중되었으며, 그 결과 이곳에서의 입성장에 빨랐고 $Al_2O_3$의입성장 억제효과도 상대적으로 뛰어났다. 입계 및 입내균열전파가 일어났으나 $Al_2O_3/12Ce-TZP$의 경우가 $Al_2O_3/3Y-TZP$에 비하여 입계파괴가 우세하였다

• 한국세라믹학회지
• /
• 제39권4호
• /
• pp.413-419
• /
• 2002

$Al_2O_3$/TiC/SiC, $Al_2O_3$/SiC 및 $Al_2O_3$/TiC 복합체들을 고온가압소결로 제조하여 이들의 균열저항거동과 기계적 성질을 비교해 보았다. $Al_2O_3$에 $0.8{\mu}m$의 TiC가 30vol% 첨가된 $Al_2O_3$/TiC는 단일체 $Al_2O_3$와 비슷한 균열저항거동을 보이며 파괴인성은 전반적으로 10% 이내의 증가를 보이는데 그쳤지만 강도는 약 30% 증가하였다. $Al_2O_3$에 $3{\mu}m$ SiC가 30vol% 첨가된 $Al_2O_3$/SiC는 SiC 입자의 균열 접속으로 인해 증가하는 균열저항거동을 뚜렷이 보이면서 파괴인성이 긴 균열에서 약 75% 증가하였으나 강도는 다소 감소했다. $Al_2O_3$/TiC에 SiC 입자가 30 vol% 첨가된 $Al_2O_3$/TiC/SiC 복합체의 경우 단일체 $Al_2O_3$에 비해 긴 균열 거리에서 파괴인성이 50% 이상 증가된 6.6 MP${\cdot}\sqrt{m}$에 이르렀으며 강도 값도 약 20% 상승하였다. 그러나 큰 SiC 입자의 첨가로 인해 TiC 입자만 첨가된 $Al_2O_3$/TiC 복합체보다는 강도가 다소 낮았다. 또한 SiC 입자만 첨가된 $Al_2O_3$/SiC 복합체보다는 파괴인성이 다소 낮았는데, 이는 작은 TiC 입자들이 SiC 입계를 거칠게 만들어 균열접속을 일으키는 SiC 입자의 뽑힘 현상을 방해하였기 때문이다.

• 한국세라믹학회지
• /
• 제40권5호
• /
• pp.494-500
• /
• 2003

금속 제련공정에서 배출되는 특정폐기물인 EAF(Electrical Arc furnace) dust를 점토와 혼합하여 건축용 벽돌을 제조함에 있어 A1203의 첨가가 소결범위에 미치는 영향을 연구하였다. $Al_2$O$_3$ 첨가되지 않은 시편은 1200-125$0^{\circ}C$에서 과량의 액상에 의해 기포가 형성되고 개기공(open pores)이 감소함으로 겉보기 밀도가 크게 감소하였으며 125$0^{\circ}C$ 이상에서는 기포가 시편 외부로 소멸되어 흡수율이 증가되었다. 그러나 $Al_2$O$_3$가 첨가된 Clay-Dust 계 소결체는 1200-125$0^{\circ}C$ 구간에서 소결온도에 따른 밀도 변화율이 크게 감소되었고, 125$0^{\circ}C$ 이상에서는 흡수율(%)의 증가율이 둔화되었다. $Al_2$O$_3$가 첨가되지 않은 시편은 1275$^{\circ}C$에서 소결된 경우 cristobalite상이 주된 상인 반면, mullite(3Al$_2$O$_3$ 2SiO$_2$)상은 소량 합성되었고, 원료성분인 hematite(FeAl$_2$O$_4$)는 소멸되지 않아 액상이 과량 생성되는 조성임을 확인하였다. 반면 $Al_2$O$_3$가 l5 wt% 첨가된 시편의 경우, 1275$^{\circ}C$에서 cristobalite는 완전 소멸되고 mullite상이 합성되어 주상이 되며, hematite 상이 일부 AI$_2$O$_3$와 반응하여 hercynite(FeAl$_2$O$_4$)상을 형성하여 액상 생성량이 많지 않을 것으로 분석되었다. 이상의 결과로부터 Clay-Dust계에 $Al_2$O$_3$를 첨가하면 액상의 발생량과 특성 및 결정상 종류를 변화시켜줌으로써 시편물성의 변화율을 감소시켜 소결온도 범위를 넓히는 효과가 있는 것으로 분석되었다.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제3C권4호
• /
• pp.140-145
• /
• 2003

The influence of microstructure nonuniformity on the electrical characteristics of ZnO varistors was analyzed with the added amount of $Al_2$O$_3$ dopants. $Al_2$O$_3$ doping can effectively inhibit grain growth. When $Al_2$O$_3$ content is in the range between 0-0.1 %, the average grain size and the standard deviation decrease quickly and the grain growth is strongly inhibited. Therefore, it is possible to increase the microstructure uniformity by accurate addition of $Al_2$O$_3$ to the ZnO varistor. The breakdown voltage increases with the decrease of standard deviation. The greater the uniformity of the Zno varistor means the higher the global breakdown voltage. The $Al_2$O$_3$ dopants having about 0-0.023 wt% content can effectively improve the voltage ratio, and the voltage ratio reaches a minimum value of 2.32 at an $Al_2$O$_3$ content of 0.005 wt%.

• 한국세라믹학회지
• /
• 제32권12호
• /
• pp.1392-1400
• /
• 1995

WC-10wt%Co-Al2O3 ceramic composites, using both the SHS (Self-propagating High Temperature Synthesis) synthesized WC powder method and commercial WC powder, were prepared by varing WC-Co/Al2O3 vol% ratio and sintering temperature (1350℃∼1650℃) for 1 hr in Ar atmosphere. Mechanical characterization has been investigated by Instron meterial testing system and Vicker's hardness test. Compositional and structural chracterizations were carried out by energy-dispersive analysis of X-ray (EDAX) data and scanning electron microscope (SEM). Electrical characterization was carried out by the electrical resistivity measurement using 4-point probe method. As sintering period increased and Al2O3 contents decreased in WC-10wt%Co-Al2O3 ceramic composite, shrinkage and relative density increased, resulting in maximum values at 1600℃. Also the major matrix phase changed with increasing Al2O3 content from 0 to 100 vol%. It was also identified by SEM, EDAX, and electrical resistivity measurement. Based on the results of analysis of flexural strength, toughness and hardness, the mechanical properties of WC-10wt%Co-Al2O3 ceramic composites using the SHS synthesized WC powder were better than those WC-10wt%Co-Al2O3 ceramic composites using commercial WC powder because WC-10wt%Co-Al2O3 ceramic composites using the SHS synthesized WC powder were sintered very well due to small initial particle size. By the addition of 40 vol% Al2O3 [60(WC=10wt%Co)-40Al2O3], it was possible to obtain a proper candidate as a superalloy.