• 한국주조공학회지
• /
• 제15권4호
• /
• pp.360-367
• /
• 1995

Effects of metal coating treatment on SiC particle on wetting behavior and interfacial strength were studied. Experimental variables are included types of coated metallic films such as Cu and Ni-P, and temperatures of heat-treatment under vacuum. The experimental results concerning wetting phenomena of liquid Al on SiC, showed that coating treatment of metallic film on SiC particles remarkably improves the wetting behavior of liquid Al on SiC, especially in the case of Ni-P coating. The interfacial strength of Al/SiC composites made of coated SiC plate was higher than that of the composite with non-coated SiC plate although the coating treatment was not perfect.

• Applied Microscopy
• /
• 제26권1호
• /
• pp.95-104
• /
• 1996

A comprehensive methodology to characterize the interfacial reaction products of $SiC_p/2024$ Al composites is introduced on the basis of the experimental results obtained using XRD, SEM and TEM. XRD performed on the electrochemically extracted $SiC_p$ and bulk $SiC_p/2024$ Al composite have shown that the interfacial reaction products consist of $Al_{4}C_3$ having hexagonal crystallographic structure, pure eutectic Si having diamond cubic crystallographic structure, and $CuAl_2$, having tetragonal crystalloraphic structure, respectively. According to the images observed by SEM, $Al_{4}C_3$, which has been reported to have needle shape, has a hexagonal platelet-shape and eutectic Si is found to have a dendritic shape. In addition eutectic $CuAl_2$, was observed to form near interface and/or along the grain boundaries. In order to confirm the results obtained by XRD, the primitive cell volume and reciprocal lattice height of such interfacial reaction products were calculated using the data obtained from convergent beam electron diffraction (CBED) patterns, and then compared with theoretical values.

• 한국재료학회지
• /
• 제4권8호
• /
• pp.945-951
• /
• 1994

분말야금법으로 제조된 $SiC_{p}$/6061 Al 복합재료의 열간 압출가공에 있어서 압출성에 미치는 빌렛의 특성과 압출조건의 영향에 대하여 조사하였다. 압출가공성의 난이도를 판단 할 수 있는 기준이 되는 최대압출력과 변형저항 값($K_{w}$)은 350ton 압출기를 이용한 압출압력의 측정과 Watanabe등의 경험식에 의해 도출되었다. 6061Al합금기 복합재료 빌렛의 전단변형저항고 압출압력은 강화재($SiC_{p}$)의 부피분율이 증가함에 따라 증가하고 있으나, 증가되는 비율은$SiC_{p}$인 경두가 $SiC_{w},Al_{2}O_{3f}$/보다 작았다. 강화입자 크기가 작을 수록 변형저항 값이 증가하였고 압출성도 양호하였다. 변형저항 값의 증가는 기지금속의 가공경화에 기인하며, 최대압출력을 나타내는 피이크는 강화재의 입자가 미세할 수록, 즉 가공경호가 클 수록 뾰족한 형상을 나타내었다. 압출온도가 증가할 수록 변형저항 값이 낮아져서 작은 압출력으로도 복합재료의 압출이 가능하나, $500^{\circ}C$이상인 경우 압출재 표면에 극심한 tearing현상이 발생하였다.

• Applied Microscopy
• /
• 제29권3호
• /
• pp.281-289
• /
• 1999

교반관법으로 제조한 $AZ91HP/SiC_p$ Mg 복합재료를 틱소포팅하여 미세조직과 존재상들을 조사하였다. $AZ91HP/SiC_p$ Mg 복합재료를 반응고 가공시 액상율 50% 이상에서 완전 충전이 이루어겼으며 전형적인 반응고 조직을 보였다. 복합재료내의 강화상이 초정 $\alpha$상의 합체, 조대화를 억제하여 보다 용이하게 thixotropic 조직을 가질 수 있었다. TEM 관찰결과, 복합재료내의 계면반응 생성물은 MgO, $Mg_2Si$ 및 $Al_{12}Mg_{17}$등이며, 직접 가압시 정출상으로 나타나는 비평형상인 decagonal T상이 관찰되었으며, 이 상은 간접가압시 안정상인 $Al_6Mn$의 형태로 관찰되었다. 이는 간접가압시 승온시간이 직접가압보다 상대적으로 길어, 비평형의 decagonal T상이 안정한 $Al_6Mn$상으로 생성된 것으로 판단된다. 아직까지 생성과정이 명확하진 않으나 교반관법으로 제조 후, 2차가압 성형시 비평형상의 존재는 재료의 강화에 기여할 것으로 판단된다.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1994년도 춘계 학술발표 강연 및 논문 개요집
• /
• pp.76-76
• /
• 1994

• 한국주조공학회지
• /
• 제14권3호
• /
• pp.258-266
• /
• 1994

AC4A $Al/Al_2O_3+SiC_p$ hybrid composites were fabricated by the squeeze infiltration technique. Effect of applied pressure, volume fraction of reinforcement($Al_2O_3$ and SiC) and SiC particle size($4.5{\mu}m$, $6.5{\mu}m$ and $9.3{\mu}m$) on the solidification microstructure of the hybrid composites were examined. Mechanical properties were estimated preliminarly by fractographic observation, hardness measurement and wear test. Results show that the microstructure of the hybrid composites were quite satisfactory, namely revealing relatively uniform distribution of reinforcements and refined matrix. Some aggregation of SiC particle caused by particle pushing was observed especially in the hybrid composites containg in fine particle($4.5{\mu}m$). Refined matrix was attributed to applied pressure and increased nucleation sites with addition of reinforcements. Fractured facet also revealed finer for the hybrid composites possibly due to refined matrix. Hardness and wear resistance increased with volume fraction of reinforcements. For hybrid composites with $9.3{\mu}m$ SiC, hardness was somewhat lower and wear resistance higher than other composites.

• 한국군사과학기술학회지
• /
• 제7권1호
• /
• pp.47-58
• /
• 2004

Loss factors of A356, Mn-Cu alloy and aluminum matrix composites reinforced with $SiC_p$ and Ni-coated graphite particles at various contents have been investigated using clamped-free cantilever beam method. The loss factors of half-power bandwidth of the specimens were measured over a wide range of frequencies from 50 to 3300Hz. Among the specimens, Al-10%$SiC_p$-10%$C_p$ showed the highest loss factor at the mode I, while Mn-Cu alloy showed the highest loss factors at the modes II and III. Consequently, at the mode I the Al-10%$SiC_p$--10%$C_p$ showed the loss factor of 0.00093, which is 2.64 and 1.58 times higher than those of A356 and Mn-Cu alloy, respectively.

• 한국분말재료학회지
• /
• 제2권3호
• /
• pp.238-246
• /
• 1995

The purpose of this study is to establish powder metallurgy (P/M) fabrication processes for high performance 2XXX Al composites reinforced with SiC whiskers. Rapidly solidified 2XXX Al powders produced by commercial atomization technique were mixed with SiC whiskers. The results of mixing processes indicated that fluidized zone mixing technique was considerably effective for the large scale production of the mixture of Al powders and whiskers. In order to consolidate these $Al-SiC_w$ mixtures into $Al-SiC_w$ composite billets, a vacuum hot press was set up, and hot processing variables were investigated. Using the hot pressing temperature of $620^{\circ}C$ under the pressure of 50 MPa, good quality $Al-SiC_w$ composite billets having relatively homogeneous microstructure and sound Al/sic interfacial bonding were obtained. Composite billets were then extruded to bars having relatively homogeneous microstructures at the extrusion temperature of 450~500$^{\circ}C$ under the extrusion pressure of 700~ 1000 MPa. Mechanical properties of the extruded bars were found to be comparable with those of the composite processed by Advanced Composite Materials Corp. To improve mechanical properties of the composites, elimination of coarse intermetallic compounds, uniform distribution of reinforcements, and minimization of whisker breakage are suggested.

• 한국자동차공학회논문집
• /
• 제13권4호
• /
• pp.174-181
• /
• 2005

In order to investigate the behavior of fatigue crack growth of SiC-particulate- reinforced Al-Si alloy composites, fatigue tests using single edge notched tension(SENT) specimens were performed. Composite materials were manufactured by using both permanent die casting and extrusion processes with different volume fractions of $10\%\;and\;20\%$. $SiC_p-reinfurced$ Al-Si composites showed the increased levels of threshold stress intensity factor range, ${\Delta}K_{th}$, for the increased volume fractions of SiC particles, which implies the increased fatigue crack growth resistance at the threshold or low ${\Delta}K$ levels, compared to the unreinforced Al-Si alloy. In the Paris region, however, the composites showed the increased rate of crack growth resulting in the unfavorable effects on the fatigue crack growth resistance. Critical stress intensity factor range at unstable crack growth leading to final fracture decreased as the volume fraction of SiC particle increased, because of the reduced fracture toughness of the composites. Extruded materials showed higher threshold and critical values than the cast materials.

• 한국전기전자재료학회논문지
• /
• 제22권2호
• /
• pp.128-131
• /
• 2009

Silicon carbide (SiC) has attracted significant attention for high frequency, high temperature and high power devices due to its superior properties such as the large band gap, high breakdown electric field, high saturation velocity and high thermal conductivity. We performed Al ion implantation processes on n-type 4H-SiC substrate using a SILVACO ATHENA numerical simulator. The ion implantation model used Monte-Carlo method. We simulated the effect of channeling by Al implantation in both 0 off-axis and 8 off-axis n-type 4H-SiC substrate. We have investigated the effect of varying the implantation energies and the corresponding doses on the distribution of Al in 4H-SiC. The controlled implantation energies were 40, 60, 80, 100 and 120 keV and the implantation doses varied from $2{\times}10^{14}$ to $1{\times}10^{15}\;cm^{-2}$. The Al ion distribution was deeper with increasing implantation energy, whereas the doping level increased with increasing dose. The effect of post-implantation annealing on the electrical properties of Al-implanted p-n junction diode were also investigated.