• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.961-965
• /
• 1998

The rapid development of small-scale (1-10 MJ) Superconducting Magnetic Energy Storage Systems (SMES) can be explained by real perspective of practical implementation of these devices in electro power nets. However the serious problem of all high mechanically stressed superconducting coils-problem of training and degradation (decreasing) of operating current still exists. Moreover for SMES systems this problems is more dangerous because of pulsed origin of mechanical stresses-one of the major sources of local heat disturbances in superconducting coils. We investigated acoustic emission (AE) phenomenon on model and 0.5 MJ SMES coils taking into account close correlation of AE and local heat disturbances. Two-coils 0.5 MJ SMES system was developed, manufactured and tested at Russian Research Center in the frames of cooperation with Korean Electrical Engineering Company (KEPCO) [1]. The two-coil SMES operates with the stored energy transmitted between coils in the course of a single cycle with 2 seconds energy transfer time. Maximum operating current 1.55 kA corresponds to 0.5 MF in each coil. The Nb-Ti-based conductor was designed and used for SMES manufacturing. It represents transposed cable made of Nb-Ti strands in copper matrix, several cooper strands and several stainless steel strands. The coils are wound onto fiberglass cylindrical bobbins. To make AE event information more useful a real time instrumentation system was used. Two main measured and computer processed AE parameters were considered: the energy of AE events (E) and the accumulated energy of AE events (E ). Influence of current value in 0.5 MJ coils on E and E was studied. The sensors were installed onto the bobbin and the external surface of magnets. Three levels of initial current were examined: 600A, 1000A, 2450 A. An extraordinary strong dependence of the current level on E and E was observed. The specific features of AE from model coils, operated in sinusoidal vibration current changing mode were investigated. Three current frequency modes were examined: 0.012 Hz, 0.03 Hz and 0.12 Hz. In all modes maximum amplitude 1200 A was realized.

• Structural Monitoring and Maintenance
• /
• 제7권1호
• /
• pp.13-25
• /
• 2020

One of the most important aspects in structural health monitoring is the detection of fatigue damage. Structural components such as heavy-duty bolts work under high dynamic loads, and thus are prone to accumulate fatigue damage and cracks may originate. Those heavy-duty bolts are used, for example, in wind power generation and mining equipment. Therefore, the investigation of new and more effective monitoring technologies attracts a great interest. In this study the acoustic emission (AE) technology was employed to detect incipient damage during fatigue testing of a M36 bolt. Initial results showed that the AE signals have a high level of background noise due to how the load is applied by the fatigue testing machine. Thus, an advanced signal processing method in the time-frequency domain, the Hilbert-Huang Spectrum (HHS), was applied to reveal AE components buried in background noise in form of high-frequency peaks that can be associated with damage progression. Accordingly, the main contribution of the present study is providing insights regarding the detection of incipient damage during fatigue testing using AE signals and providing recommendations for further research.

• 비파괴검사학회지
• /
• 제31권1호
• /
• pp.62-67
• /
• 2011

모의 낙뢰시험에 의해 충격손상을 입은 탄소섬유강화플라스틱(CFRP) 복합재료의 잔류압축강도를 평가하는 시험(CAI) 중 손상부의 거동을 음향방출(AE)법으로 관찰하였다. CFRP 시편은 ITO 나노입자를 탄소섬유에 직접 코팅한 CFRP prepreg를 이용하여 만들었고, 모의 낙뢰시험은 고전압 대전류 인가장치(ICG)를 이용하여 시편에 10~40 kA의 충격파 전류를 인가하여 실시하였다. ITO 나노입자 코팅의 효과와 인가전류의 세기에 따른 손상영역의 크기와 잔류압축강도를 AE 거동과 연관하여 평가하였다. 손상영역의 크기는 초음파 C-scan 영상을 이용하여 측정하였으며, AE events 수와 AE event가 발생하기 시작할 때의 압축응력 수준을 연관시킨 결과 ITO 나노입자 코팅 CFRP의 경우 상대적으로 손상이 작고 훨씬 높은 용력수준에서 AE가 발생하기 시작하였다. CAI시험 중 AE측정은 실제로 낙뢰손상을 입은 복합재 동체 구조물의 손상된 정도를 구별하는 데 유용한 지표로 활용될 수 있음을 확인하였다.

• 터널과지하공간
• /
• 제24권1호
• /
• pp.67-80
• /
• 2014

본 연구에서는 임계하균열성장 변수를 구하기 위해 제안된 Wilkins의 시험법을 압열인장시험과 결합하여 화강암의 인장강도, Mode I 파괴인성과 임계하균열성장지수를 동시에 구하였으며 이를 사용하여 암석의 장기거동을 평가하였다. 또한 내부압력을 받는 압축공기저장(CAES) 공동에 대한 장기안정성을 수치해석코드인 FRACOD를 사용하여 해석하였다. 시험 결과 화강암의 임계하균열성장지수(n)는 29.39로 결정되었으며 5 ~ 6 MPa의 내압은 저장공동의 장기안정성에 큰 영향을 미치지 않는 것으로 나타났다. 또한 시험 과정에서 측정한 미소파괴음을 분석한 결과 암석내의 미소균열 생성 및 전파에 따른 암석의 손상을 정량적으로 기술할 수 있었다. 만약, 실내와 동일한 조건으로 현장에서 AE 모니터링을 수행할 경우 AE 모니터링을 통해서 하중을 받는 암석의 현재 상태를 정량적으로 평가하는 것이 가능할 것으로 판단된다.

• 한국환경과학회지
• /
• 제8권5호
• /
• pp.617-623
• /
• 1999

This study was carried out to obtain the optimal operating parameter on organic matters and nutrient removal of mixed wastewater which was composed of sewage and stable wastewater using SBR. A laboratory scale SBR was operated with An/Ae(Anaerobic/Aerobic) ratio of 3/3, 2/4 and 4/2(3.5/2.5) at organic loading rate of 0.14 to 0.27 kgBOD/$m^3$/d. TCOD/SCOD ratio of mixed wastewater was 3, so the important operating factor depended upon the resolving the particulate parts of wastewater. Conclusions of this study were as follows: 1) For mixed wastewater, BOD and COD removal efficiencies were 93-96% and 85-89%, respectively. It was not related to each organic loading rate, whereas depended on An/Ae ratio. During Anarobic period, the amount of SCOD consumption was very little, because ICOD in influent was converted to SCOD by hydrolysis of insoluble matter. 2) T-N removal efficiencies of mixed wastewater were 55-62% for Exp. 1, 66-76% for Exp. 2, and 67-81% for Exp. 3, respectively. It was found that nitrification rate was increased according to organic concentration in influent increased. Therefore, the nitrification rate seemed to be achieved by heterotrophs. During anoxic period, denitrification rate depended on SCOD concentration in aerobic period and thus, was not resulted by endogenous denitrification. However, the amount of denitrification during anaerobic period were 3.5-14.1 mg/cycle, and that of BOD consumed were 10-40 mg/cycle. 3) For P removal of mixed wastewater, EBPR appeared only Mode 3($3^＊$). It was found that the time in which ICOD was converted to VFA should be sufficient. For mode 3 in each Exp., P removal efficiencies were 74, 87, and 81%, respectively. But for 45-48 of COD/TP ratio in influent, P concentration in effluent was over 1 mg/L. It was caused to a large amount of ICOD in influent. However, as P concnetration in influent was increased, the amounts of P release and uptake were increased linearly.

• 정보보호학회논문지
• /
• 제32권1호
• /
• pp.1-9
• /
• 2022

Fixslicing AES는 Bitsliced AES의 선형 계층에서 많은 Cycle이 발생하는 것을 최소화하기 위해 Shiftrows 단계를 생략한 기법으로 Bitsliced 기법 대비 30% 성능 향상을 보여준다. 하지만 생략된 Shiftrows를 보완하기 위해 코드량이 증가되기 때문에 Shiftrows를 절반만 생략한 Semi-Fixsliced와 완전히 생략한 Fully-Fixsliced로 나뉜다. 본 논문에서는 사전 연산 테이블 기법을 활용한 RISC-V 상에서의 Fixslicing AES의 CTR 모드 구현을 제안한다. CTR 모드의 특징을 활용하여 2-라운드 SubBytes 연산까지의 사전 연산을 통해 암호화 과정에서 2-라운드 SubBytes까지 생략한 빠른 암호화가 가능하다. 해당 기법을 활용하여 32-bit RISC-V 상에서 Semi-Fixsliced는 하나의 블록을 암호화하는 비용은 1,345 Cycle이며 기존 대비 7%의 성능 향상, Fully-Fixsliced는 1,283 Cycle 이며 기존 대비 9%의 성능 향상을 확인하였다.

• 한국가스학회지
• /
• 제7권2호
• /
• pp.48-53
• /
• 2003

에너지 관련 플랜트에 사용되는 배관은 플랜트의 성능이나 안전성유지에 있어서 중요한 설비의 일부이다. 본 연구에서는 고압탄소강 배관의 변형 및 파괴에 대한 음향방출 기초 자료를 얻기 위하여 압력용기용 배관재를 기계가공하여 인장시험편을 만든 후, 인장시험을 실시하여 항복, 소성변형 및 파괴에 이르기까지의 음향방출 신호를 분석하였다. 탄성영역, 최대인장강도 이전의 소성영역 및 최대인장강도 이후의 소성영역에서 검출된 음향방출의 시간-주파수 분석 결과는 탄성영역에서 항복영역까지는 비교적 낮은 저주파수 대역(250${\~}$350kHz)이 나타났으며, 소성영역에서는 저주파수뿐만 아니라 고주파수 대역(500kHz)도 나타났다. 인장시험 후, 이러한 각 영역의 구별이 가능하였던 원인은 항복영역에서의 전위의 이동, 집적에 따른 신호와 최대인장강도 이전의 소성영역에서의 전위들이 개재물이나 결정입계를 통과했을 때 나타나는 신호, 최대인장강도 이후에는 미소공동의 발생, 성장 및 합체에 의하여 나타나는 신호로 분류가 가능하였기 때문인 것으로 판단된다.

• 상하수도학회지
• /
• 제22권4호
• /
• pp.437-444
• /
• 2008

Many other countries have investigated the new backwash water treatment process to save the existing water resource. There are various methods for reusing backwash water, but the membrane system has received the most interest for its efficiency. The objective of this study was to certify the application of membrane filtration system for the backwash water treatment. The experiment equipment was composed of Lab scale tubular membrane filtration system. Generally, cross-flow operation mode is used in the tubular membrane system but cross-flow operation mode demands high electric cost mainly for the pump energy. So to cut off electric cost, dead-end operation mode was used in this experiment. Filtration and bleed operation cycle was used in this membrane system. Backwash water was concentrated during the filtration process and when backwash water reached our target suspended solid concentration, it was discharged from this system. For efficient operation of filtration and bleed, mathematical matrix was drawn up and with this matrix we could simulate various sets of filtration and bleed time.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2002년도 춘계학술대회 논문집
• /
• pp.134-139
• /
• 2002

Fracture behaviors of pipes with local wall thinning are very important for the integrity of nuclear power plant. However, effects of local wall thinning on strength and fracture behaviors of piping system were not well studied. Acoustic emission(AE) has been widely used in various fields because of its extreme sensitivity, dynamic detection ability and location of growing defects. In this study, we investigated failure modes of locally wall thinned pipes and AE signals by bending test. From test results, we could be divided four types of failure modes of ovalization, crack initiation after ovalization, local buckling and crack initiation after local buckling. And fracture behaviors such as elastic region, yielding range, plastic deformation range and crack progress could be evaluated by AE counts, accumulative counts and time-frequency analysis during bending test. It is expected to be basic data that can protect a risk according to local wall thinning of pipes, as a real time test of AE.

• 비파괴검사학회지
• /
• 제21권3호
• /
• pp.251-260
• /
• 2001

단조인장시험하에서 CFRP적층재의 손상과정을 음향방출과 초음파시험에 의해 평가하였다. 시험편으로부터의 음항방출신호의 진폭 분포는 기지재 균열(matrix crack), 박리(debonding), 섬유 pull-out 및 섬유 과단(fiber fracture)과 같은 CFRP에서의 파괴기구를 분석하는데 도움을 주며, 초음파 진폭감쇠의 특성 또한 각각의 파괴기구를 분석하는데 유용하다. 여러종류의 CFRP시험편을 사용하여 음향방출신호와 초음파신호의 진폭감쇠를 조사하였다. 끝으로 하중 제하중(loading-unloading) 시험이 초음파내의 진폭비에 대한 Felicity effect와 감쇠를 조사하기 위해서 수행되었다. 전 실험에 걸쳐 초음파신호의 진폭감쇠와 음향방출 파라미터(parameter)들은 동시에 검출되었다. 이로써 음향방출과 초음파시험의 두 파라미터들이 CERP에서의 파괴기구를 분석하기 위해 효과적으로 사용될 수 있음이 확인되었다.