• Electrical & Electronic Materials
• /
• v.29 no.6
• /
• pp.22-27
• /
• 2016

• Korean Journal of Materials Research
• /
• v.21 no.4
• /
• pp.192-195
• /
• 2011

The electro-deposition of compound semiconductors has been attracting more attention because of its ability to rapidly deposit nanostructured materials and thin films with controlled morphology, dimensions, and crystallinity in a costeffective manner (1). In particular, low band-gap $A_2B_3$-type chalcogenides, such as $Sb_2Te_3$ and $Bi_2Te_3$, have been extensively studied because of their potential applications in thermoelectric power generator and cooler and phase change memory. Thermoelectric $Sb_xTe_y$ films were potentiostatically electrodeposited in aqueous nitric acid electrolyte solutions containing different ratios of $TeO_2$ to $Sb_2O_3$. The stoichiometric $Sb_xTe_y$ films were obtained at an applied voltage of -0.15V vs. SCE using a solution consisting of 2.4 mM $TeO_2$, 0.8 mM $Sb_2O_3$, 33 mM tartaric acid, and 1M $HNO_3$. The stoichiometric $Sb_xTe_y$ films had the rhombohedral structure with a preferred orientation along the [015] direction. The films featured hole concentration and mobility of $5.8{\times}10^{18}/cm^3$ and $54.8\;cm^2/V{\cdot}s$, respectively. More negative applied potential yielded more Sb content in the deposited $Sb_xTe_y$ films. In addition, the hole concentration and mobility decreased with more negative deposition potential and finally showed insulating property, possibly due to more defect formation. The Seebeck coefficient of as-deposited $Sb_2Te_3$ thin film deposited at -0.15V vs. SCE at room temperature was approximately 118 ${\mu}V/K$ at room temperature, which is similar to bulk counterparts.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1459-1462
• /
• 2007

In general a thermoelectric cooler (TEC) consists of a series of P type and N type thermoelectric materials sandwiched between two wafers. When a DC current passes through these materials, three different effects take place; Peltier effect, Joule heating effect and heat transfer by conduction due to temperature difference between hot and cold plates. In this study we have developed a micro TEC using $Bi_2Te_3$ (N type) and $Bi_{0.5}Sb_{1.5}Te_3$ (P type) thin films. In order to improve that performance of a micro TEC, we made 10 um height TE legs using special PR only for lift-off. We measured COP (coefficient of performance) and temperature difference between hot and cold connectors with current.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.178-178
• /
• 2008

초소형 박막의 열전 발전모듈은 작은 부피와 한번 설치시 교체없이 지속적인 전원공급으로 소형의 센서 노드에 전원으로 각광 받고 있다. 이에 본 논문에서는 In Plane방식의 PIN Junction의 박막형 열전소자를 제작하여 보았다. 열전 박막인 P-type의 $BiSbTe_3$와 N-type의 $Bi_2Te_3$은 (001)GaAs 기판에 MOCVD(Metal Organic Chemical Vapour Deposition)방식으로 성장하였으며 전극으로는 E-Beam Evaporator를 이용하여 금(Au), 알루미늄(Al)을 사용하였다. 열전박막의 두께는 MOCVD의 성장시간과 온도 MO-x 가스의 압력으로 조절하여 주었다. 제작결과 1Pairs 당 약 $63{\mu}V$/K을 나타내었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.142-142
• /
• 2007

Micro thermoelectric generator has been attractive for the alternative power source to operate the wireless sensor node. In this paper, we designed the column-type micro thermoelectric device and their device characteristics were measured. n-type Bi2Te3 and p-type BiSbTe3 thermoelectric thin films were grown on (001) GaAs substrates by metal organic chemical vapour deposition (MOCVD) and they were pattemed. The height of thermoelectric film were controlled by the deposition time, temperature and MO-x gas pressure. Seebeck coefficient was measured at room temperature and hole concentration and electrical resistivity of thermoelectric film were also characterized.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.129-129
• /
• 2017

열전재료는 열에너지를 전기에너지로 또는 전기에너지를 열에너지로 직접 변환하는데 가장 널리 사용되는 재료이다. $Bi_2Te_3$계 열전 재료는 400K 이하의 비교적 저온 영역에서 높은 성능지수(Dimensionless Figure of merit, ZT($={\alpha}2{\sigma}T/{\kappa}$, ${\alpha}$: 제백계수, ${\sigma}$: 전기전도도, T: 절대온도, ${\kappa}$: 열전도도))를 나타내는 열전재료이며 자동차 시트나 정수기 등에 응용되고 있다. 열전모듈은 제조시 수십 개에서 수백 개 이상의 n형 및 p형 열전소자를 알루미나($Al_2O_3$)와 같은 세라믹 기판(substrate) 상에 접합된 동 전극 위에 전기적으로 서로 직렬로 접합시켜 제조한다. 기존의 열전모듈의 제조방법에는 동 전극 위에 위에 Sn합금 분말과 플럭스(flux)의 혼합물인 솔더페이스트를 스크린 인쇄법을 사용하여 동 전극에 도포한 다음, 그 위에 열전소자를 얹고 약 520K의 열풍을 가하여 솔더를 용융시켜 열전소자와 동 전극을 접합시킨다. 스크린 인쇄법에서는 인쇄 압력이 일정하지 않으면, 솔더페이스트 층의 두께가 균일하지 않게 되어 열전소자 접합부의 불량을 유발시킨다. 그러나 열모듈은 단 하나의 접합 불량이 모듈 전체의 열전변환성능에 심각한 영향을 줄 수 있기 때문에 본 연구에서는 이러한 문제점을 해결하기 위해, 솔더페이스트를 도포하지 않고 열전소자를 직접 동 전극과 접합할 수 있는 방법을 고안하였다. 무전해도금을 이용한 니켈층을 형성시킨 $Bi_2Te_3$계 열전소자 표면에 약 $50{\mu}m$의 주석도금층을 전기도금법을 구사하여 형성시켰다. 그 후, wire cutting을 통하여 $3mm{\times}3mm{\times}3mm$의 크기로 절단한 주석도금된 열전소자를 동 전극에 얹고 1.1KPa의 압력을 가하면서 523K의 핫플레이트 위에서 3분간 방치하여 직접(direct) 열압착 접합을 실시하였다. 접합부의 단면을 SEM을 이용하여 관찰한 결과, 동 전극과 열전소자 사이의 계면에 용융 후 응고된 주석층이 결함없이 균일하게 형성된 양호한 접합부를 관찰할 수 있었다. 따라서, 솔더페이스트를 이용하지 않고, 열전소자 표면에 주석도금을 실시한 후, 동 전극과 직접 열압착 본딩을 실시하는 방법은 균일한 접합계면을 얻을 수 있는 새로운 공정으로 기대된다.

• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.3
• /
• pp.67-74
• /
• 2018

Thermoelectric thin film devices of the in-plane configuration consisting of 8 pairs of n-type $Bi_2Te_3$ and p-type $Sb_2Te_3$ legs were processed on Si submounts by electrodeposition. The thermoelectric generation characteristics of the thin film devices were investigated with respect to the apparent temperature difference ${\Delta}T$ caused by LED lighting as well as the change of the leg thickness. When ${\Delta}T$ was 7.4 K, the open circuit voltages of 6.1 mV, 7.4 mV, and 11.8 mV and the maximum output powers of 6.6 nW, 12.8 nW, and 41.9 nW were measured for the devices with the thermoelectric legs of which thickness were $2.5{\mu}m$, $5{\mu}m$, and $10{\mu}m$, respectively.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1675-1677
• /
• 2005

In case of attaching thermoelectric module and heat source, the polymer sheet is attached on the $AL_{2}O_3$ plate, which Is cold and hot side of thermoelectric module, in order to enhance mechanical safty of the system. It is impossible to calculate the exact distribution of temperature and flow pattern of inner gap of thermoelectric module. Therefore CFD(Computational Fluid Dynamics) analysis was executed to determine the thermo-fluid phenomena and distribution by Fluent. As the result of these analysis, heat transfer was dominated by conduction and the difference of temperature was linear distribution according to the thickness of polymer sheet.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2003.12a
• /
• pp.331-331
• /
• 2003

• Proceedings of the Korean Magnestics Society Conference
• /
• 2004.06a
• /
• pp.134-135
• /
• 2004