• Transactions on Electrical and Electronic Materials
• /
• 제3권3호
• /
• pp.21-24
• /
• 2002

Two kinds of $Nd_{1+X}Ba_{2-X}Cu_3O_{7-{\delta}}$, the sintering samples and zone melting samples, were heat-treated under pure Ar at 950$^{circ}C$. The substitution of Nd ion for Ba ion in the $Nd_{1+X}Ba_{2-X}Cu_3O_{7-{\delta}}$ before and after the heat treatment was investigated by XRD. In order to confirm the effects of the heat treatment, the Tc and Jc of samples with/without the heat treatment under Ar were comparatively studied. $Nd_{1+X}Ba_{2-X}Cu_3O_{7-{\delta}}$ samples were oxygenated under pure oxygen at $300^{circ}C$. From the XRD pattern it was found that the sample with x<0.4 was transferred from tetragonal phase to orthorhombic phase after the oxygenation, while the sample with x>0.4 did not show the phase transition even after a long time oxygenation. Therefore, the low oxygen partial pressure (Ar+1 % O$_2$) was used for the ambient atmosphere of the zone-melting samples, which could reduce the melting temperature and depress the substitution of Nd for Ba. After the improvement in the zone-melting process, the Jc value was increased to 2 x $10^4$A/$cm^2$ (0 T, 78 K). The particle orientation and the structure of zone-melted NdBaCuO were studied by the XRD and SEM analysis.

• 한국재료학회지
• /
• 제31권9호
• /
• pp.519-524
• /
• 2021

The impact properties of two austenitic Fe-23Mn-0.4C steels with different Al contents for cryogenic applications are investigated in this study. The 4Al steel consists mostly of austenite single-phase microstructure, while the 5Al steel exhibits a two-phase microstructure of austenite and delta-ferrite with coarse and elongated grains. Charpy impact test results reveal that the 5Al steel with duplex phases of austenite and delta-ferrite exhibits a ductile-to-brittle transition behavior, while the 4Al steel with only single-phase austenite has higher absorbed energy over 100 J at -196 ℃. The SEM fractographs of Charpy impact specimens show that the 4Al steel has a ductile dimple fracture regardless of test temperature, whereas the 5Al steel fractured at -100 ℃ and -196 ℃ exhibits a mixed fracture mode of both ductile and brittle fractures. Additionally, quasi-cleavage fracture caused by crack propagation of delta-ferrite phase is found in some regions of the brittle fracture surface of the 5Al steel. Based on these results, the delta-ferrite phase hardly has a significant effect on absorbed energy at room-temperature, but it significantly deteriorates low-temperature toughness by acting as the main site of the propagation of brittle cracks at cryogenic-temperatures.

• 대한기계학회논문집
• /
• 제8권1호
• /
• pp.34-40
• /
• 1984

In this study, martensite-ferrite dual phase steel composed of martensite in hard phase and ferrite in soft phase is made as model material, and the difference of fatigue crack propagation behavior resulted from the structural size is investigated by fracture mechanics and microstructural method. The main results obtained are as follows; 1)Fatigue crack propagation rate is influenced by ferrite grain size. In other words, in the low .DELTA. K region fatigue crack propagation rate is decreased with decreasing of grain size but the difference of propagation rate resulted from the structural size is decreased as .DELTA.K is increased. 2)The above result is explained by the degree of crack arrest effect of second phase for fatigue crack propagation depending on the ratio of reversed plastic zone size to ferrite grain size.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제15권3호
• /
• pp.342-348
• /
• 2015

This paper presents a 1.9-GHz digital ${{\Delta}{\Sigma}}$ fractional-N PLL with a finite impulse response (FIR) filter embedded for noise suppression. The proposed digital implementation of FIR provides a simple method of increasing the number of taps without complicated calculation for gain matching. This work demonstrates 32 tap FIR filtering for the first time and successfully filtered the in-band phase noise generated from delta-sigma modulator (DSM). Design considerations are also addressed to find the optimum number of taps when the resolution of time-to-digital converter (TDC) is given. The PLL, fabricated in $0.11-{\mu}m$ CMOS, achieves a well-regulated in-band phase noise of less than -100 dBc/Hz for the entire range inside the bandwidth of 3 MHz. Compared with the conventional dual-modulus division, the proposed PLL shows an overall noise suppression of about 15dB both at in-band and out-of-band region.

• Journal of Electrical Engineering and Technology
• /
• 제13권2호
• /
• pp.550-558
• /
• 2018

This paper presents the current limit strategy of voltage controller of delta-connected H-bridge static synchronous compensator (STATCOM) under an unbalanced voltage fault event. When phase to ground fault happens, the feasibility to heighten the magnitude of sagging phase voltage is considered by using symmetric transformation method in delta-structure STATCOM. And the efficiency to cover the maximum physical current limit of switching device is considered by using vector analysis method that calculate the zero sequence current for balancing the cluster energy in delta connected H-bridge STATCOM. The result is simple and obvious. Only positive sequence current has to be used to support the unbalanced voltage sag. Although the relationship between combination of the negative sequence voltage with current and zero sequence current is nonlinear, the more negative sequence current is supplying, the larger zero sequence current is required. From the full-model STATCOM system simulation, zero sequence current demand is identified according to a ratio of positive and negative sequence compensating current. When only positive sequence current support voltage sag, the least zero sequence current is needed.

• 대한금속재료학회지
• /
• 제50권7호
• /
• pp.511-516
• /
• 2012

Low temperature ${\delta}$-precipitation phenomenon below 2-step aging ($718^{\circ}C$, $8hr+621^{\circ}C$, 8 hr) temperature of cold drawn Inconel 718 alloy wire was investigated. The investigation was carried out on wires with a cold drawn ratio of 0, 20, 50 and 70% using OM, SEM, XRD, TEM, and DSC. In microstructures of 50 and 70% drawn wire, many precipitates were found along the grain boundaries and the twin boundaries in deformation band. From the results of the XRD and TEM analysis, the precipitates were identified as plate-like ${\delta}$-phase. From the results of the DSC analysis, it was also found that a temperature of ${\delta}$-precipitation decreases with an increase of the cold drawn ratio. We concluded that cold drawing of inconel 718 wire promotes the ${\delta}$-precipitation, and under the condition of a high drawing ratio, the ${\delta}$-phase could be precipitated at a temperature below the aging temperature ($718^{\circ}C$).

• 한국응용과학기술학회지
• /
• 제14권1호
• /
• pp.61-76
• /
• 1997

Triacylglycerols of the seeds of Ginkgo biloba have been resolved by high-performace liquid chromatography(HPLC} in the silver-ion and reverse-phase modes. The fatty acids were identified by a combination of capillary gas chromatography and gas-chromatography /mass spectrometry as the methyl and /or picolinyl ester. The main components are $C_{18:2{\omega}6}$(39.0mol%), $C_{18:1{\omega}7}$(asclepic acid 21.5mol%), and $C_{18:1{\omega}9}$(oleic acid, 13.8mol%). Considerable amounts of unusual acid such as $C_{20:3{\Delta}^{5,11,14}$ (5.7mol%), $C_{18:2{\Delta}^{5,9}$(2.8mol%), and $C_{18:3}{\Delta}^{5,9,12}$(1.6mol%), were checked. In addition, an anteiso-branched fatty acid, 14-methylhexadecanoic acid, was also present as a minor component(0.9 mol%). The triacylglycerols were separated into 17 fractions by reverse-phase HPLC, and the fractionation was achieved according to the partition numnber(PN) in which a ${\Delta}^5$-non methylene interrupted double bond($^5$-NMDB) showed different behaviour from a methylene interrupted double bond in a molecule with a given cahinlength. Silver-ion HPLC exhibited excellent resolution in which fractions(23 fractions) were resolved on the basis of the number and configuration of double bonds. In this instance, the strength of interaction of a ${\Delta}^5$-NMDB system with silver ions seemed to be weaker than a methylene interrupted double bond system. The principal triacylglycerol species are as follows ; $(C_{18:2{\omega}6)2}/C_{18:1{\omega}7}$, $C_{18:1{\omega}9}/C_{18:1{\omega}7}/C_{18:2{\omega}6}$, $(C_{18:1{\omega}7)2}/C_{18:2{\omega}6}$, $C_{16:1{\omega}7}/C_{18:1{\omega}9}/C_{20:3}{\Delta}^{5,11,14}$, $C_{16:1{\omega}7}/C_{18:1{\omega}7}/C_{20:3}{\Delta}^{5,11,14}$, $C_{18:1{\omega}9}/C_{18:1{\omega}7}/C_{18:2{\omega}6}$, $C_{18:1{\omega}9}/C_{18:2}{\Delta}^{5,5}/C_{20:3}{\Delta}^{5,11,14}$, $(C_{18:1{\omega}7)2}/C_{18:2{\omega}6}$ and $(C_{18:1{\omega}9)2}/C_{18:2{\omega}6}$, while simple triacylglycerols without $C_{18:2{\omega}6})_3$ were not present. Stereospecific analysis showed that fatty acids with ${\Delta}^5$-NMDB system and saturated chains were predominantly located at the site of sn-3 carbon of glycerol backbones. It is evident that there is asymmetry in the distribution of fatty acids in the TG molecules of Ginkgo nut oils.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.570-576
• /
• 2002

Application of the aged Inconel 718 in hydrogen environment is seriously restraint by its high hydrogen embrittlement (HE) sensitivity. m previous researches, we have suggested the possibility and applicability of the laser surface annealing (LSA) process in improving the HE resistance of this alloy. Sequentially, a study on the effects of the precipitates in the Inconel 718 on its HE sensitivity was conducted in this research. Firstly, flat bar specimens were heat-treated to obtain various kinds of precipitation microstructures concerning the ${\gamma}$" phase and the 6 phase. Hydrogen was charged into the specimen by a cathodic charging process. The loss in reduction of area (RA) caused by hydrogen charging was used to assess the HE sensitivity. The HE sensitivity of the alloy was lowered with decreasing the volume fraction of ${\gamma}$". Moreover, it was possible to increase the HE resistance of the aged alloy by dissolving the $\delta$ phase, keeping the strength at the same level as that of the common aged alloy. Thus, we concluded that both the $\delta$ phase and the ${\gamma}$" phase affected the HE sensitivity of Inconel 718. Next, two kinds of notch tensile specimens were fabricated, one kind having $\delta$ phase and the other having no $\delta$ phase. All these specimens were aged via the same aging heat treatment process. The LSA process annealed a thin layer of the notch bottom of each specimen. One specimen of each kind was charged with hydrogen by the cathodic hydrogen charging process. Loss in the notch tensile strength (NTS) caused by hydrogen was used to evaluate the HE sensitivity. It was found that while the HE sensitivity of conventionally aged Inconel 718 was decreased by the LSA process, the HE sensitivity of the $\delta$-free aged Inconel 718 could further be decreased. Therefore, for applications in hydrogen environments, it is possible to fabricate alloys with both good HE resistance and high strength by controlling the precipitation conditions, and to improve HE resistance further via applying the LSA process.

• 대한화학회지
• /
• 제32권5호
• /
• pp.458-463
• /
• 1988

역상 액체크로마토그래피법으로 페놀류에 대한 분리현상을 용해도파라미터이론에 의해 알아 본 결과 예측한 용리거동이 제한된 범위내에서만 일치하고 있었다. 이 용해도 파라미터이론에 의한 용리현상의 설명은 실제 실험의 결과와 상당히 상이하게 나타났고 많은 예외가 있었다. 그러므로 새로운 용질-용매상호작용파라미터 ${\delta}_{im}$ 을 첨가하여 실제 실험값에 가까운 용해도파라미터 이론식으로 수정하였다. 이 새로운 용질-용매상호작용파라미터, ${\delta}_{im}$ 는 용매의 종류, 용매분율과 용질의 구조에 의존하고 있으며 이 파라미터, ${\delta}_{im}$와 혼합이동상의 용해도파라미터, ${\delta}_{im}$ 와는 직선의 관계가 있었다. 이것은 머무름거동을 예측하는데 이전의 Schoenmakers의 식보다 더 좋은 결과로 나타났다.

• 천문학회보
• /
• 제41권2호
• /
• pp.58.3-58.3
• /
• 2016

The Kepler space mission provides quantitative and qualitative photometric time series of oscillating stars. It is possible to examine statistical study with seismic properties of solar-like stars. Global seismic properties - large frequency separation (${\Delta}{\nu}$), frequency of maximum power (${\nu}_{max}$) and amplitude of Gaussian envelope (A) widely have been used to determine empirical scaling relations for inferring the stellar physical quantities - mass, age and temperature. We aim to confirm whether width of Gaussian envelope on power excess (${\delta}{\nu}_{env}$) can be used with parameter of scaling relation before redgiant phase using Kepler data. Therefore we analyze the characteristics of ${\delta}{\nu}_{env}$ of 129 solar-like stars from main-sequence to subgiant. We have demonstrated that ${\delta}{\nu}_{env}$ has highly correlations with global parameters - ${\Delta}{\nu}$ and ${\nu}max$. We have also found the break of ${\delta}{\nu}_{env}-{\Delta}{\nu}$ and ${\nu}_{max}$ relations.