• Journal of Adhesion and Interface
• /
• v.13 no.1
• /
• pp.38-44
• /
• 2012

Surface properties and curing behavior of UV-initiated photopolymerization with and without wax have been investigated by pendulum hardness, pencil hardness, gloss, photo-differential scanning calorimetry (photo-DSC) and SEM. In addition, the influence of wax type (paraffin wax, PE wax) on the various properties of UV cured films was studied. The results showed that the wax type was the significant factor affecting gloss and surface hardness of UV cured films. Specially, the photo-DSC results showed that ${\Delta}H$ for the UV cured films containing paraffin wax was higher than the corresponding values for the formulation without wax and with PE wax. The observed results clearly demonstrate that the photopolymerization of UV curing with paraffin wax in an air atmosphere is less inhibited by the oxygen compared to UV curing without wax and with PE wax.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.5
• /
• pp.952-958
• /
• 1988

To analyze the nonflatness and residual stress in accelerated cooled plate, a numerical analysis model has been developed. Two factors, i.e. temperature and phase transformation, are considered in calculating the stress distribution that develops during cooling. The plastic strain and plate-buckling, which are often shown in accelerated cooled plate, were determined from this stress. Mean temperature in through thickness direction and temperature difference in width direction are considered in the model to simplify the calculation. The temperature and stress distribution changes caused by phase transformation are involved in terms of the effective specific heat and the effective thermal expansion coefficient. With the model, accelerated cooling of 10mm(t) $^{*}$3000mm(w) plate was simulated. The condition of accelerated cooling was .deg. C/sec from just after hot rolling to 500.deg. C. The initial temperature-difference ratio, .DELTA.Tr, in width direction is an important factor in evaluating the stress distribution. When .DELTA.Tr is 0.08, buckling occurs during cooling and 7kgf/m $m^{2}$ of residual stress develops at the edge of plate. To secure the flatness, .DELTA.Tr should be less than 0.07. Small scaled cooling test was conducted to verify the exactness of the model and the results proved the usefulness of this numerical analysis model.l.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.4
• /
• pp.181-191
• /
• 2006

The most common kind of vehicular accident is the low-speed rear-end impact that result in high portion of insurance claims and Whiplash Associated Disorders(WAD). The low-speed collisions have specific characteristics that differ from high speed collisions and must be treated differently This paper presents a simple continuous contact force model for the low-speed rear-end impact to simulate the accelerations, velocities and the contact force as functions of time. A smoothed Coulomb friction force is used to represent the effect of braking, which was found to be significant in simulating low-speed rear end impact. The intervehicular contact force is modeled using nonlinear damping and spring elements with coefficients and exponents. This paper presents how to estimate analytically stiffness and damping coefficients. The exponent of the nonlinear contact force model was determined to match the overall acceleration pulse shape and magnitude. The model can be used to determine ${\Delta}Vs$ and peak accelerations for the purpose of accident reconstruction and for injury biomechanics studies.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.4
• /
• pp.612-618
• /
• 1998

Monolithic SiC and SiC/C FGM layers were deposited on the graphite substrates by the CVD method and their thermal properties of the two specimens were investigated by thermal shock test for comparison. Temperature profiles and thermal stress distributions on thermal shock test were calculated by a commercially used computer program to see the thermal stress differences inside of two specimens. The specimens coated with FGM were expected to show a efficient relaxation of thermal stresses at the interface and they were not cracked under the actual $\Delta$T=1600 K experimental condition. This result proved that the experimental results were well accorded with the expectation from the theoretical calculations.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1225_1226
• /
• 2009

유리 기판 상에 이중 게이트 절연막을 가지는 우수한 특성의 P형 엑시머 레이저 어닐링 (ELA) 다결정 실리콘 박막 트랜지스터를 제작하였다. 그리고 P형 짧은 채널 ELA 다결정 실리콘 박막 트랜지스터의 오프 상태 스트레스 하에서의 전기적 특성을 분석하였다. 스트레스하에서 긴 채널에서의 문턱 전압은 양의 방향으로 거의 이동하지 않는 (${\Delta}V_{TH}$ = 0.116V) 반면, 짧은 채널 박막 트랜지스터의 문턱 전압은 양의 방향으로 상당히 이동 (${\Delta}V_{TH}$ = 2.718V)하는 것을 확인할 수 있었다. 이런 짧은 채널 박막 트랜지스터에서 문턱 전압의 양의 이동은 다결정 실리콘 막과 게이트 산화막 사이의 계면에서의 전자 트랩핑 때문이다. 또한, 박막 트랜지스터의 누설 전류는 오프 상태 스트레스 하에서의 채널 영역의 홀 전하로 인하여 온 전류 수준을 감소시키지 않고 억제될 수 있었다. C-V 측정 결과는 계면의 전자 트랩핑이 드레인 접합 영역부근에서 발생한다는 것을 나타낸다.

• Environmental Analysis Health and Toxicology
• /
• v.22 no.2 s.57
• /
• pp.177-184
• /
• 2007

Gaseous organochlorine pesticides (OCPs : heptachlor epoxide, p, p'-DDE, ${\gamma}-HCH,\;{\alpha}-chlordane,\;{\gamma}-chlordane$ and trans-nonachlor) concentration was measured using PUF high volume sampler from June, 2000 to June, 2002 in the semi-rural atmosphere. The OCPs concentration in atmosphere, which is estimated by the slope (m) of Clausius-Clapeyron equation and phase-transition energy $({\Delta}H)$, was influenced by revolatilization from environmental matrix (soil, water and tree leaves) and a long range transportation of air mass. But the former affected OCPs concentration more than the latter. The degradation rate constants (k) of OCPs calculated using multiple regression analysis and revised standard temperature method were in good agreement each other. The value of k of ${\gamma}-HCH$ was very low as -0.0007, but the range of k of other components were $-0.00l8{\sim}-0.0038$. The half-life $({\tau})$ which was calculated by k of ${\gamma}-HCH$ was 2.6 years-the longest one, but that of heptachlor epoxide was in 0.5 year-the shortest one. $({\tau})\;of\;{\alpha}-chlordane,\;{\gamma}-chlordane$ and trans-nonachlor in technical chlordane was 1.0, 1.1 and 0.7 year respectively.

• Journal of Astronomy and Space Sciences
• /
• v.16 no.1
• /
• pp.69-78
• /
• 1999

We have developed an attitude sensing S/W system, one of modules of Mission Analysis System(MAS), which simulates attitude sensing data as almost the same as the real sensor of a satellite in orbit. When attitude elements($alpha,delta$) of a satellite and positions of Earth, Moon, and Sun are given, the S/W system calculates look angles and dihedral angles of each celestial bodies relative to the rotations axis of the satellite. It consists of two sub-modules : One is ephemeris service module which consider the perturbations of four planets(Venus, Mars, Jupiter, Saturn) for positions of Sun and Moon and 4 $\times$4 earth gravitational potential terms for a satellite's position. The other is attitude simulation module which generates attitude sensing data. Varying the rotational axis of a satellite and it's orbital elements, we simulated the generating attitude sensing data with this S/W system and discussed their results.

• Journal of Welding and Joining
• /
• v.8 no.4
• /
• pp.27-34
• /
• 1990

Integranular corrosion behaviors of KAL (Knife Line Attack) and mechanical properties such as tensile and creep rupture were investigated for the tube material used for nearly 20 years under the condition of 463.deg. C and 28 $kg/cm^2$. Based and weld metal were austenitic stainless steel AISI 321 containing Ti, AISI 347 containing Nb, respectively. KLA is a kind of the intergranular corrosion which often occurs just near the HAZ (heat affected zone) of AISI 321 and AISI 347 stainless steel due to the grain boundary sensitization. In KLA zone, intergranular corrosion crack has propagated outwards from the inner surface and carbides of white and narrow band type assuming as (Cr, Fe) carbide were confirmed. All the delta-ferrite formed in the weld metal during weld solidification has been transformed into sigma-phase since delta-ferrte was exposed for 20 years at 463.deg. C. Elongation was very low at the range from room temperature to 600.deg. C and it was confirmed that creep-rupture properties were not consideralbly affected.

• Journal of Power System Engineering
• /
• v.11 no.3
• /
• pp.35-40
• /
• 2007

Leak would happen because of the damage of high temperature and high-pressure valve in nuclear power plant. condition based prevention maintenance is essential by using the suitable method based on local condition. Energy loss prevention can prevent from an accurate test, Local actually and ability. The methods of test for high energy fluid leak at present are analysis of ${\Delta}T$, AE(Acoustic Emission) analysis, and thermal image. The result for test of secondary system in nuclear power plant Unit reveals that the AE occurred clearly in leakage situation, but thermal image didn't occur. It is identified that leak is occurred when the orifice located front and back of valve operates. It shows that making a impatient judgment by using the single method if it is leakage is containing uncertainty. So we think that using the Multi-Measuring method is more sound judgment than single-measuring method.

• Economic and Environmental Geology
• /
• v.30 no.1
• /
• pp.15-23
• /
• 1997

Gold mineralization of the Ogkye gold mine was deposited mainly in quartz veins up to 150 cm wide which occupy fissures in Cambrian Pungchon limestone. Ore minerals are relatively simple as follows: pyrite, arsenopyrite, pyrrhotite, sphalerite, electrum and galena. On the basis of the Ag/Au ratio on ore grades, mode of occurrence and assoicated mineral assemblages, the Ogkye gold deposit can be classified as pyrite-type gold deposit (Group IIB). Fluid inclusion data indicate that ore minerals were deposited between $400^{\circ}$and $230^{\circ}C$ from relatively dilute fluids (0.2 to 7.3 wt.% eq. NaCl) containing $CO_2$. The ore mineralization resulted from a complex history of $CO_2$ effervescence and local concomitant boiling coupled with cooling and dilution of ore fluids. Gold deposition was likely a result of decrease of sulfur activity caused by sulfide deposition and/or $H_2S$ loss accompanying fluid unmixing. Sulfur isotope compositions of sulfide minerals (${\delta}^{34}S=3.5{\sim}5.9$‰) are consistent with ${\delta}^{34}S_{H_2S}$ value of 4.8 to 6.1‰, suggesting mainly an igneous source of sulfur partially mixed with wall-rock sulfur.