• Korean Journal of Materials Research
• /
• v.22 no.10
• /
• pp.499-503
• /
• 2012

The present study is intended to comparatively investigate the changes in microstructure and tensile properties at room and elevated temperatures in commercial AM50(Mg-5%Al-0.3%Mn) and 0.3 wt%CaO added ECO-AM50 alloys produced by permanent mould casting. The typical microstructure of AM50 alloy was distinctively characterized using two intermetallic compounds, ${\beta}(Mg_{17}Al_{12})$ and $Al_8Mn_5$, along with ${\alpha}$-(Mg) matrix in an as-cast state. The addition of a small amount of CaO played a role in reducing dendrite cell size and quantity of the ${\beta}$ phase in the AM50 alloy. It is interesting to note that the added CaO introduced a small amount of $Al_2Ca$ adjacent to the ${\beta}$ compounds, and that inhomogeneous enrichment of elemental Ca was observed within the ${\beta}$ phase. The ECO-AM50 alloy showed higher hardness and better YS and UTS at room temperature than did the AM50 alloy, which characteristics can be mainly ascribed to the finer-grained microstructure that originated from the CaO addition. At $175^{\circ}C$, higher levels of YS and UTS and higher elongation were obtained for the ECO-AM50 alloy, demonstrating that even 0.3 wt%CaO addition can be beneficial in promoting the heat resistance of the AM50 alloy. The combinational contributions of enhanced thermal stability of the Ca-containing ${\beta}$ phase and the introduction of a stable $Al_2Ca$ phase with high melting point are thought to be responsible for the improvement of the high temperature tensile properties in the ECO-AM50 alloy.

• The Korean Journal of Physiology and Pharmacology
• /
• v.9 no.1
• /
• pp.23-27
• /
• 2005

The present study was performed to investigate the effects of intra-articular injection of interleukin-1${\beta}$ (IL-1${\beta}$) on the formalin-induced temporomandibular joint (TMJ) pain. Under anesthesia, a 30-gauge needle was introduced into the right TMJ region for injection of formalin. Microinjection of 50 ${\mu}l$ of 5% formalin significantly produced noxious scratching behavioral response, and the scratching behavior lasted for 40 min. Although the responses produced by formalin injection were divided into two phases, the response of 1st phase did not significantly differ from the scratching behavior response in the saline-treated group. We examined the effects of intra-articular injection of IL-1${\beta}$ on the number of noxious behavioral responses produced by 50${\mu}l$ of 5% formalin injection. Intra-articular injection of 100 pg and 1 ng of IL-1${\beta}$ significantly increased the number of behavioral responses of the 2nd phase, while 10 pg of IL-1${\beta}$ did not change the formalin-induced behavioral responses. To investigate whether IL-1 receptor was involved in the intra-articular administration of IL-1${\beta}$-induced hyperalgesic response, IL-1 receptor antagonist (IL- ra, 50 ng) was administrated together with IL-1${\beta}$ injection. IL-1${\beta}$ receptor antagonist blocked IL-1${\beta}$- induced hyperalgesic response in the TMJ formalin test. These results suggest that intra-articular injection of IL-1${\beta}$ facilitated the transmission of nociceptive information in the TMJ area.

• YAKHAK HOEJI
• /
• v.50 no.1
• /
• pp.21-25
• /
• 2006

Reiterated normal-phase column chromatography lead to the isolation and purification of six known compounds but for the first time from the whole plant of Sasa borealis (Hack.) Makino (Gramineae): tricin 4'-O-(erythro-${\beta}$-guaia-cylglyceryl) ether (1), tricin 4'-O-(threo-${\beta}$-guaiacylglyceryl) ether (2), tricin 4'-O-[erythro-${\beta}$-guaiacyl-(9'-O-acetyl)-glyceryl] ether (3), tricin 4'-O-[threo-${\beta}$-guaiacyl-(9'-O-acetyl)-glyceryl] ether (4), (-)-pinoresinol (5), and vanillin (6). The structures of the compounds (1-6) were established based on interpretation of high resolution NMR (COSY, HSQC, HMBC, and NOESY) spectral data. In particular, compounds 1 and 3 were diastereomers of compounds 2 and 4, respectively. These two sets of diastereomers were able to be simultaneously identified and quantified by a gradient reversed-phase HPLC method with UV photodiode array, This sensitive HPLC method is noteworthy as a simultaneous separation and identification method to test the extract of the family Gramineae which contains these compounds.

• Journal of Pharmaceutical Investigation
• /
• v.28 no.3
• /
• pp.141-149
• /
• 1998

In order to reduce systemic side effects following administration, flurbiprofen was formulated as O/W microemulsion consisting of the surfactant, oil phase and aqueous phase. Particle size distribution, apparent viscosity, solubility and skin permeation of flurbiprofen in various vehicles and microemulsion were evaluated. The domain of O/W microemulsion s phase diagram had difference between oil types and the area of O/W microemulsion was wide distributed by adding to PG and cosurfactant than that of water alone. As increasing 10, 15 and 20% of Brij 97 content and 1, 2.5, 5% of oil content, the solubility of flurbiprofen in O/W microemulsions and various vehicles was $400{\sim}1,000$ and $10{\sim}500$ times higher than that of control. Also, apparent viscosity of soybean oil microemulsions was higher than that of IPM microemulsions and that of vehicle were increased as increasing vehicle content. Since skin permeation of flurbiprofen decreased as increasing viscosity, in each vehicle, it was not affected 2% ${\beta}-CD$ and decreased as increasing PG content and to 2, 5 and 10% of $HP-{\beta}-CD$. In O/W microemulsion, 5% soybean oil. 20% Brij 97 and 75% water(A-1) with high viscosity showed low skin penetration.

• Korean Journal of Materials Research
• /
• v.17 no.9
• /
• pp.480-483
• /
• 2007

Hydroxyapatites were prepared by the different $SiO_2$ addition at $1450^{\circ}C$ for 2h. With the increase of $SiO_2$ addition, microstructure, bulk density, porosity, mechanical strength of $hydroxyapatite/{\beta}-TCP$ composite were investigated. When the sintered HAp contained 1 wt% $SiO_2$, the each properties of the HAp were increased. But the excess addition of $SiO_2$ content above 1wt% the each property were decreased. This results were due to the ${\beta}-TCP$ phase. The ${\beta}-TCP$ phase appeared at 3 wt% $SiO_2$ addition and the ${\beta}-TCP$ phase was enhanced by the $SiO_2$ increasing.

• Journal of the Korean Ceramic Society
• /
• v.24 no.1
• /
• pp.23-32
• /
• 1987

Synthesis of high purity ultrafine Si3N4 and ${\beta}$-Sialon powders was investigated via the simultaneous reduction and nitriding of amorphous SiO2, SiO2-Al2O3 system prepaerd by hydrolysis of alkoxides, using carbonablack as a reducing agent. In Si(OC2H5)4-C2H5 OH-H2 O-NH4OH system, hydrolysis rate increased with increasing reaction temperature and pH. Pure ${\alpha}$-Si3N4 was formed at 1350$^{\circ}C$ for 5 hrs in N2 atmosphere. In Si(OC2H5)4-Al(OC3H7)3-C6H6-H2 O-NH4OH system, weight loss increased as Si/Al ratio decreased. Single phase ${\beta}$-Sialon consisted of Si/Al=2 was formed at 1350$^{\circ}C$ in N2 and minor phases of ${\alpha}$-Si3N4, AIN, and X-phase were existed besides theSialon phase at other Si/Al ratios. The Si3N4 and Sialon powders synthesized from alkoxides consisted of uniform find particles of 0.05-0.2$\mu\textrm{m}$ in diameter, respectively.

• Archives of Pharmacal Research
• /
• v.22 no.6
• /
• pp.608-613
• /
• 1999

Optimum conditions of chiral derivatization reaction of $\beta$-blockers (acebutolol, arotinolol, betaxolol, bisoprolol, celiprolol, metoprolol and pindolol) with (-)-menthyl chloroformate were investigated for the resolution by HPLC. With more than 30 times molar excess of (-)-methyl chloroformate chiral derivatization reactions were completed within one hour at room temperature except arotinolol and celiprolol. Diastereomeric derivatives of $\beta$-blockers were well resolved on the ODS column using acetonitrile-methanol-water as a mobile phase.

• Clean Technology
• /
• v.12 no.2
• /
• pp.101-106
• /
• 2006

HT-$LiCoO_2$ powders were synthesized from hydroxide precursors in this study. The cobalt hydroxide compounds with hydrotalcite-like(${\alpha}$-phase) and/or brucite-like(${\beta}$-phase) structures as a component of the precursor were prepared in various PH conditions using precipitation method. It was found that various phase and compositions of cobalt hydroxides could be tailor-prepared via a careful control of preparation parameters such as the concentration ratio of $[OH^-]/[CO^{2+}]$ and aging time. The hydroxides $Co(OH)_2$ and LiOH were mixed with aqueous methyl-alcohol. The precursor of a HT-$LiCoO_2$ was synthesized via subsequent processes including evaporation, drying and aging. The transformation of tailor-made ${\beta}$-phase $Co(OH)_2$ to CoOOH and formation of solid solution in the precursor were achieved during aging. These results cause HT-$LiCoO_2$ to be synthesized at low temperature($600^{\circ}C$ ) for a short time(10min).

• Transactions of Materials Processing
• /
• v.14 no.8 s.80
• /
• pp.681-688
• /
• 2005

The high-temperature deformation mechanisms of a ${\alpha}+{\beta}$ titanium alloy (Ti-6Al-4V), near-a titanium alloy (Ti-6.85Al-1.6V) and a single-phase a titanium alloy (Ti-7.0Al-1.5V) were deduced within the framework of inelastic-deformation theory. For this purpose, load relaxation tests were conducted on three alloys at temperatures ranging from 750 to $950^{\circ}C$. The stress-versus-strain rate curves of both alloys were well fitted with inelastic-deformation equations based on grain matrix deformation and grain-boundary sliding. The constitutive analysis revealed that the grain-boundary sliding resistance is higher in the near-${\alpha}$ alloy than in the two-phase ${\alpha}+{\beta}$ alloy due to the difficulties in relaxing stress concentrations at the triple-junction region in the near-${\alpha}$ alloy. In addition, the internal-strength parameter (${\sigma}^*$) of the near-${\alpha}$ alloy was much higher than that of the ${\alpha}+{\beta}$ alloy, thus implying that dislocation emission/ slip transfer at ${\alpha}/{\alpha}$ boundaries is more difficult than at ${\alpha}/{\beta}$ boundaries.

• Journal of the Korean Society for Heat Treatment
• /
• v.18 no.2
• /
• pp.91-98
• /
• 2005

Both commercially pure titanium and Ti-6Al-4V alloy have been widely used as biomaterials because of their excellent biocompatibility, corrosion resistance and mechanical properties. However, in recent years, vanadium has been found to cause cytotoxic effects and adverse tissue reactions, while aluminium has been associated with potential neurological disorders. A newly designed ${\alpha}+{\beta}$ type Ti alloy, Ti-10Ta-10Nb alloy showed superior properties to CP Ti and Ti-6Al-4V alloy in the point of biomaterial, and elucidated the future uses as a biomaterial. Microstructural changes of Ti-10Ta-10Nb alloy after hot-rolling, warm-rolling, solution and aging treatment were investigated. According to TEM results, the microstructures after solution treatment were composed of mostly ${\alpha}$ phase with a trace of ${\beta}$ phase due to adding ${\beta}$-phase stabilizer tantalum and niobium. The microstructures after warm-rolling is coarse and elongated ${\alpha}$ phase and hot rolling resulted in very fine ${\alpha}$ widmanst$\ddot{a}$tten. The highest value of hardness was obtained by aging treatment at $400^{\circ}C$ for 20hr in which microstructure consisted of very fine ${\alpha}$ phase in ${\beta}$ matrix.