• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.4
• /
• pp.645-650
• /
• 1998

Alumina- and yttria-coated SiC powder was prepared by the surface-induced precipitation method, and sintered properties of silicon carbide prepared from this powder were investigated. After a well dispersion of SiC powders in the aqueous solution of $Al_2(SO_4)_3$ and $Y_2(SO_4)_3$, the mixed precursors of aluminum hydroxide, aluminum carbonate, yttrium hydroxide, and yttrium carbonate were precipitated on the surfaces of SiC particles through the hydrolysis reaction of urea. SiC specimens with alumina and yttria exhibit, 97.8% of theoretical density after the sintering at $1900^{\circ}C$ for 2 hrs. During annealing at $2000^{\circ}C$, $\beta$longrightarrow$\alpha$ phase transformation of SiC had taken place and resulted with a rodlike microstructure. Toughness of sintered SiC was enhanced by crack deflection around the rodlike grains. In case of annealing less than that of 3 hr, the fracture toughness of SiC was slightly improved with increasing the amount of sintering aid. However, annealed specimens for a long time showed constant fracture toughness even though the amount of sintering aid increased. It is resulted that the main factor for toughening in annealed SiC for a long time is the pullout effect of rodlike grains during the propagation of cracks, and the amount of sintering aids is less effective on the fracture toughness of SiC.

• Resources Recycling
• /
• v.13 no.1
• /
• pp.14-21
• /
• 2004

Spent catalysts containing platinum were generated in petroleum refinery and other chemical industries. The reclamation of platinum metals from such wastes has long been attempted in view of their rare, expensive and indispensable nature. In this study, the recovery of platinum from petroleum catalysts was attempted by a method consisting mainly of dissolving alumina carrier with sulfuric acid thereby concentrating insoluble platinum. Also, platinum dissolved partially in sulfuric acid was recovered by a cementation method using aluminum metal as a reductive agent. The effect of temperature, time, concentration of sulfuric acid, and pulp density on the dissolution of carrier was investigated. When the carrier of platinum catalyst was $\Upsilon-Al_2$O$_3$ about 95% alumina was dissolved in 6.0 M sulfuric acid at $100^{\circ}C$ for 2 hours. When the carrier was the mixture of $\Upsilon-Al_2$$O_3$ and $\alpha$-$Al_2$$O_3$ about 92% was dissolved after 4 hours. As a result, more than 99% of platinum could be recovered by this method and aluminum sulfate was also obtained as byproduct.

• Membrane Journal
• /
• v.27 no.2
• /
• pp.199-204
• /
• 2017

In this study, a study was carried out for the separation of metal ions in lignin extract discharged from the pulp process. alumina powders were mixed with DMAc (N, N-dimethylacetamide) solvent and PESf (Polyethersulfone) polymer, PVP (polyvinylpyrrolidone) dispersant was added and slip casting method was used to prepare the membrane. The membrane was measured for pore size through a CFP (Capillary Flow Porometer) device and the surface and cross-section of the membrane were observed through a FE-SEM (Field Emission Scanning Electron Microscope). The flux was calculated by measuring the filtered weight per hour using a separation experiment device. Pore size measurements were performed under increasing pressure from 0 psi to 30 psi. The pore size of the membrane was $0.4{\mu}m$ and the flux decreased from the initial flux value of $6.36kg{\cdot}m^{-2}{\cdot}h^{-1}$ to $1.98kg{\cdot}m^{-2}{\cdot}h^{-1}$ due to the fouling of the membrane. After the permeation experiment, membrane contaminants were removed by simple washing. Separation experiments showed that Na contained in the initial lignin extract was reduced by 69%, Fe was removed by 87%, K by 95%, Ca by 93% and Mg by 96%.

• Journal of the Korean Chemical Society
• /
• v.35 no.3
• /
• pp.275-279
• /
• 1991

Ultra-fine alumina, ${\alpha}-Al_2O_3$, with ${\phi}$ = 0.1∼0.5 ${\mu}$m was obtained from pure ammonium aluminum sulfate(alum) as the thermal decomposition product. Pure alum(> 99.7%) could be prepared by the precepitation and the successive recrystallization in an acidic aqueous solution at pH = 1.5∼2.5, which was theoretically predicted by only considering the concentrations of hydroxide and carbonate for aluminum and sodium in the solution, and also experimentally confirmed as the optimum precepitation condition for alum without forming any impurities like aluminum hydroxide or sodium one.

• Korean Chemical Engineering Research
• /
• v.48 no.5
• /
• pp.627-631
• /
• 2010

$\alpha$-Alumna particles were prepared by a precipitation method with metal fluoride additive. Aluminum nitrate and ammonia solution were used as starting materials. $AlF_3$, $CaF_2$, and $MnF_2$ were utilized as additives. The effects of precipitation solvent and metal fluoride on the phase transformation temperature, size and morphology of $\alpha$-alumna particles were investigated. The solvent for precipitation did not affect the phase transformation temperature, while it influenced the size of $\alpha$-alumna particles. The phase transformation temperature to $\alpha$-alumna was reduced by addition of metal fluoride and was different with metal cation in metal fluoride ($AlF_3(800^{\circ}C)$ < $MnF_2(900^{\circ}C)$ < $CaF_2(950^{\circ}C)$). The addition of each of three metal fluorides led to the formation of platelike particles and, among the three additives, $MnF_2$ additive resulted in the formation of relatively small particle.

• The Journal of Advanced Prosthodontics
• /
• v.7 no.3
• /
• pp.214-223
• /
• 2015

PURPOSE. To measure the surface loss of dental restorative zirconia and the short-term bond strength between an indirect composite resin (ICR) and zirconia ceramic after various sandblasting processes. MATERIALS AND METHODS. Three hundred zirconia bars were randomly divided into 25 groups according to the type of sandblasting performed with pressures of 0.1, 0.2, 0.4 and 0.6 MPa, sandblasting times of 7, 14 and 21 seconds, and alumina powder sizes of 50 and $110{\mu}m$. The control group did not receive sandblasting. The volume loss and height loss on zirconia surface after sandblasting and the shear bond strength (SBS) between the sandblasted zirconia and ICR after 24-h immersion were measured for each group using multivariate analysis of variance (ANOVA) and Least Significance Difference (LSD) test (${\alpha}$=.05). After sandblasting, the failure modes of the ICR/zirconia surfaces were observed using scanning electron microscopy. RESULTS. The volume loss and height loss were increased with higher sandblasting pressure and longer sandblasting treatment, but they decreased with larger powder size. SBS was significantly increased by increasing the sandblasting time from 7 seconds to 14 seconds and from 14 seconds to 21 seconds, as well as increasing the size of alumina powder from $50{\mu}m$ to $110{\mu}m$. SBS was significantly increased from 0.1 MPa to 0.2 MPa according to the size of alumina powder. However, the SBSs were not significantly different with the sandblasting pressure of 0.2, 0.4 and 0.6 MPa. The possibilities of the combination of both adhesive failure and cohesive failure within the ICR were higher with the increases in bonding strength. CONCLUSION. Based on the findings of this study, sandblasting with alumina particles at 0.2 MPa, 21 seconds and the powder size of $110{\mu}m$ is recommended for dental applications to improve the bonding between zirconia core and ICR.

• Journal of Korea Foundry Society
• /
• v.41 no.2
• /
• pp.127-131
• /
• 2021

Based on its good compatibility with high-temperature environments, the Ti-48Al-2Cr-2Nb alloy is used for high-temperature materials of industrial equipment. In this study, a Ti-48Al-2Cr-2Nb alloy turbocharger turbine wheel was fabricated by a vacuum centrifugal casting method. The conditions that prevent misrun defects of the turbocharger turbine wheel blade from centrifugal casting using alumina molds were investigated. The microstructure of the alloy prepared by vacuum centrifugal casting was studied by means of optical microscopy (OM), with a micro-Vickers hardness analyzer (HV), by X-ray diffraction (XRD) and by SEM-EDS. The HV and SEM-EDS examinations of the as-cast Ti-48Al-2Cr-2Nb alloy showed that the thickness of the oxide layer (α-case) was typically less than 50 ㎛. At a high preheating temperature of 1,100℃, a moderate RPM of 260, and with an alumina mold with a large gate size, there were almost no misrun defects. Therefore, it was confirmed that a Ti-48Al-2Cr-2Nb alloy turbocharger turbine wheel with fewer misrun defects could be achieved through a high preheating temperature, a moderate RPM, a large gate size and an alumina mold to suppress the formation of alpha-case components.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.6 no.3
• /
• pp.54-61
• /
• 2003

$SnO_2$ gas sensor for the detection DMMP, simulant of nerve gas was fabricated and its characteristics were examined. Sensing materials were $SnO_2$ added by TEX>$\alpha$-$Al_{2}O_{3}$ with 0∼20wt.% and $In_{2}O_{3}$ with 0∼3wt.% and were physically mixed each material. They were deposited by screen printing method on alumina substrate. The sensor was consisted of sensing electrode with interdigit(IDT) type in front and a heater in back side. Its dimension was 7$\times$10$\times$0.6$\textrm{mm}^2$. Crystallite size 8t phase identification, specific surface area and morphology of fabricated $SnO_2$ powders were analyzed by X-ray diffraction(XRD), surface area analyzer(BET) and by a scanning electron microscope(SEM), respectively. Sensor was measured as flow type and sensor resistance change was monitored as real time using LabVIEW program. The best sensitivities were 75% at adding 4wt.% TEX>$\alpha$-$Al_{2}O_{3}$, operating temperature $300^{\circ}C$ and 87% at adding 2wt.% $In_{2}O_{3}$, operating temperature $350^{\circ}C$ to DMMP 0.5ppm. Response and recovery times were about 1 and 3 min., respectively. Repetition measurement was very good with $\pm$3% in full scale. As a result, operating temperature was lower TEX>$\alpha$-$Al_{2}O_{3}$ than $In_{2}O_{3}$, but sensitivity was higher $In_{2}O_{3}$ than $\alpha$-$Al_{2}O_{3}$.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.34-34
• /
• 2003

산업의 발달로 인하여 자원재활용의 문제와 환경 오염 방지와 더불어 에너지 절약에 대한 중요성이 확대되면서 분리 고정을 이용한 환경 오염 방지 및 에너지 절약에 대한 관심이 확대되었다. 세라믹 필터는 열악한 환경에서의 적용 그리고 에너지 소모가 적은 장점을 가지고 있다. 여러종류의 재료들 중에서 기공의 제어가 용이한 알루미나 여과막은 보에하미트(${\gamma}$-AlOOH) 분말과 금속 알콕사이드(ATSB, aluminum tri-sec butoxide)를 사용하여 간단하게 제조할 수 있다. 알루미나는 열처리 론도에 따라 $\alpha$-A1$_2$O$_3$ 결정상 뿐만 아니라 몇 가지 준안정한 결정구조를 가진다. 보에마이트(${\gamma}$-AlOOH)는 45$0^{\circ}C$ 근처에서 미세한 기공을 가진 ${\gamma}$-A1$_2$O$_3$로 상전이 되는 것으로 알려져 있고, 120$0^{\circ}C$보다 낮은 온도에서 열처리하게 되면 미세구조의 변화는 일어나지 않고 약간의 입자 성장만을 수반하는 $\delta$-A1$_2$O$_3$ 또는 $\theta$-A1$_2$O$_3$으로 상전이가 일어난다. $\alpha$-A1$_2$O$_3$로의 상전이는 기공 크기의 변화와 vermicular구조를 가지는 비정상적인 입자성장을 수반하게 된다. 여과막은 기공크기와 분포를 제어하는 것이 매우 중요하므로, 상전이와 미세구조의 변화를 이해하는 것은 중요하다.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.5
• /
• pp.98-104
• /
• 2001

A dynamic fracture toughness test method with a chevron notched ceramic specimens is proposed. The notch angles of the chevron specimens were 90, 100$^{\circ}$and 110$^{\circ}$. Finite element analysis(FEA) were done to determine the geometrical properties of chevron-notch specimens according to notch angles. The static fracture toughness of the chevron notched alumina specimen was 3.8MP$\alpha$√m similar to that of the general fracture specimen with a precrack. Dynamic fracture toughness was 4.5 MP$\alpha$√m slightly higher than the static one. These research showed the possibility of the split Hopkinson pressure bar test method using the newly proposed chevron notched specimens to get the dynamic fracture toughness of extremely brittle materials such as ceramics.