• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 가을 학술발표회 논문집(II)
• /
• pp.961-966
• /
• 2000

It is difficult to change or remedy concrete structure after hardened. It is usual to evaluate the quality of hardened concrete using several test method. This study was performed to make fundamental data that could be used to evaluate the quality of hardened concrete. This study is to estimate mix proportion of hardened concrete. Each elements of concrete needed different estimation methods. First, the cement that handled by the most important compounds measured by XRF(X-ray fluorecence) machine with scanning Ca-K${\alpha}$. Second, the coarse aggregate that divided by maximum size measured by the area comparison method that starts from the assumption of uniform distribution. Third, the fine aggregate measured by the weight comparison method that needs several prerequsite constants which concerned cement hydration reaction. Fourth, the water content would be estimated by expert system that has data base of design data, the contents of above estimation results, the characteristics of concrete strength. As the result of the above research, some conclusions are as follows. The cement estimation method resulted by reliability of mean 96.7%, standard deviation 3.92. The area comparison method resulted by reliability of mean 95.3%, standard deviation 2.08. The weight comparison method resulted by reliability of mean 93.3%, standard deviation 3.35.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 춘계학술대회 논문집
• /
• pp.333-336
• /
• 1999

The relationship between the DC degradation characteristics of the $ZnO-Bi_2O_3$ varistor and post-annealing is investigated in this study. $ZnO-Bi_2O_3$ varistors containing $SiO_2$ range 0.3 mol% were fabricated by standard ceramic techniques. The post- annealing is performed at $550^{\circ}C$ for 0, 1.5 and 5h. A little phase transition is found according to the analysis of X-ray diffraction. DC degradation tests were conducted at $115\pm3^{\circ}C$ for periods up to 22h. Current-voltage analysis was used to determine nonlinear coefficients($\alpha$). Capacitance-voltage analysis enable the donor density($N_d$) and the barrier height($E_B$) to be determined. From above analysis, it is found that the past-annealing for 5h improved degradation characteristics in $ZnO-Bi_2O_3$ with Si additive.

• 한국전기전자재료학회논문지
• /
• 제16권8호
• /
• pp.711-715
• /
• 2003

In this study, we prepared ZnO/glass and ZnO/SiO$_2$/Si thin film by Facing Targets Sputtering (FTS) system for Film Bulk Acoustic Resonator (FBAR). When the ZnO thin film applied to piezoelectric thin film, it requires good c-axis preferred orientation. And c-axis orientation has a remarkable difference with preparation conditions. Therefore, c-axis orientation must be significantly evaluated as a function of deposition conditions. Moreover, in order to prepare ZnO thin film with good crystallographic properties and progressive of efficiency of product process, the ZnO thin film should be prepared as low temperature as possible. In this work, we prepared ZnO thin films on slide glass and SiO$_2$/Si substrate. And the crystallographic characteristics of ZnO thin films on sputtering conditions were investigated by alpha-step and X-ray diffraction.

• Bulletin of the Korean Chemical Society
• /
• 제34권5호
• /
• pp.1401-1406
• /
• 2013

This study tested the feasibility of observing H/D exchange of intact protein by top-down electron capture dissociation (ECD) mass spectrometry for the investigation of protein structure. Ubiquitin is selected as a model system. Local structural information was obtained from the deuteration levels of c and $z^{\cdot}$ ions generated from ECD. Our results showed that ${\alpha}$-helix region has the lowest deuteration level and the C-terminal fraction containing a highly mobile tail has the highest deuteration level, which correlates well with previous X-Ray and HDX/NMR analyses. We studied site-specific H/D exchange kinetics by monitoring H/D exchange rate of several structural motives of ubiquitin. Two hydrogen bonded ${\beta}$-strands showed similar HDX rates. However, the outer ${\beta}$-strand always has higher deuteration level than the inner ${\beta}$-strand. The HDX rate of the turn structure (residues 8-11) is lower than that of ${\beta}$-strands (residues 1-7 and residues 12-17) it connects. Although isotopic distribution gets broader after H/D exchange which results in a limited number of backbone cleavage sites detected, our results demonstrate that this method can provide valuable detailed structural information of proteins. This approach should also be suitable for the structural investigation of other unknown proteins, protein conformational changes, as well as protein-protein interactions and dynamics.

• Journal of Magnetics
• /
• 제21권2호
• /
• pp.164-167
• /
• 2016

The effect of the B additions on glass formation and magnetic properties is reported for the $Fe_{(87-x-y)}Co_yTi_7Zr_6B_x$ (x = 2, 4, 6 and y = 35, 40) alloy system. The ribbon samples with the width of 2 mm for each composition were prepared by the melt spinning technique; furthermore, their phase information was obtained from X-ray diffraction. Glass formation and magnetic properties were measured using differential scanning calorimetry and vibrating sample magnetometer respectively. The $Fe_{45}Co_{40}Ti_7Zr_6B_2$ (x = 2 and y = 40) system has the nanocrystalline phase identified as ${\alpha}-Fe$, as well as the amorphous phase, whereas all other alloys are fully amorphous. It is associated with the role of B on the glass formation. The widest supercooled liquid region is obtained as 71 K at x = 4 (both y = 35 and 40). The saturation magnetization decreases with the increase of the amount of the B addition, and the highest value is 1.59 T as x = 2 and y = 35 for this alloy system.

• Journal of Magnetics
• /
• 제10권4호
• /
• pp.145-148
• /
• 2005

Effect of vacuum annealing on the microstructures and magnetic properties of $Fe_{84}Si_6B_{10}$ films has been investigated as a function of annealing temperature. X-ray diffraction and transmission electron microscopy were employed to analyze crystallization behavior of the films. Permeability of the films was measured at various frequencies by one-turn coil method. When the films were annealed below 673 K, the coercivity of the films did not change a lot (${\~}$1500 A/m) although the grain size of a crystalline phase in the partially crystallized films increased gradually up to about 16 nm. It then increased rapidly as the films became almost fully crystalline mostly with $\alpha$-(Fe,Si) phase at and above 723 K. On the other hand, the electrical resistivity of the films decreased monotonically with the increase of annealing temperature. The permeabilities of the films annealed at 473${\~}$673 K were all over 1000, showing the optimum value of 3500 at 523 K, and almost constant up to 300 MHz. However, those of the as-deposited and fully crystallized films were lower than 1000 and unstable at the same frequency range.

• 한국수소및신에너지학회논문집
• /
• 제14권2호
• /
• pp.97-104
• /
• 2003

The structural transitions of the matrix and the second phases of $Ti_{1.0}Mn_{0.9}V_{1.1}$ and $Ti_{1.0}Cr_{1.5}V_{1.7}$ alloys upon hydrogenation have been investigated at 293K. The effect of hydrogen isotope on their crystal structures has been also discussed. The crystal structures, Phase abundance and lattice parameters of the hydrides were determined by the Rietveld method using X-ray diffraction data. At the experimental temperature, the $Ti_{1.0}Mn_{0.9}V_{1.1}$ alloy and $Ti_{1.0}Cr_{1.5}V_{1.7}$ alloy revealed different structural transition processes upon hydrogenation although the crystal structures of these two alloys are both BCC at room temperature. The second phases such as Ti-rich phase with $NiTi_2$ structure and $\alpha$-Ti with HCP structure absorbed hydrogen at relatively low hydrogen pressures and the phase abundance remained almost constant. This means that it is desirable to decrease the amount of the second phases as far as possible in order to increase the effective hydrogen storage capacities of the alloys. The crystal structures of corresponding isotope hydrides, the phase abundance and the lattice parameters did not depend on the kind of hydrogen isotope, but only on the hydrogen content.

• The Korean Journal of Ceramics
• /
• 제6권4호
• /
• pp.401-404
• /
• 2000

Mimicking the bacterial synthesis of magnetosomes, in which the functionalized surface of a cytoplasmic (lipid) membrane is considered to be stimulating the crystal growth of magnetite, we have successfully grown magnetite films at $30^{\circ}C$ using an arachic acid monomolecular layer as a functionalized surface. The lipid monomolecular layer was spread on an aqueous solution of FeCl$_2$ which was oxidized by flowing a mixed gas, with ratio $O_2$/$N_2$=1/2000, on the surface of the lipid layer. Mossbauer and X-ray diffraction analyses revealed that the Fe$_3$O$_4$ films contain small amounts of ferric hydroxyl impurity phases of ${\alpha}$-FeOOH and ${\tau}$-FeOOH. This is because the oxygen partial pressure at the ferrite/aqueous interface changed as the film (through which the gas penetrated) increased in thickness. Methods to obtain single phase magnetite films are proposed.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2000년도 추계학술발표회 초록집
• /
• pp.12-12
• /
• 2000

This paper investigated the effect of the film deposition rate for $CrN_x$ microstructure and mechanical properties. For these purpose, pure Cr an stoichiometric CrN films were deposited with various target power density on Si hardened M2 tool steel. The variation of ni trogen concentration in $CrN_x$ f analyzed by AES and deposition rate was calculated by measuring of thickness using ${\alpha}-step$ profilometer. The microstructure was analyzed by X-Ray Diffract and Scanning Electron Microscopy(SEM), and mechanical properties were evalua residual stress, microhardness and adhesion tests. Deposition rate of Cr and CrN increased as an almost linear function of target power density from $0.25\mu\textrm{m}/min$ and $0.15\mu\textrm{m}/min$ to $0.43\mu\textrm{m}/min$. Residual stresses of Cr and CrN films were from tensi Ie to compressive stress with an increase of deposi tion rate a compressive stresses were increased as more augmentation of deposition r maximum hardness value of $2300kg/\textrm{mm}^2$ and the best adhesion strength correspond HF 1 were obtained for CrN film synthesized at the highest target densitY($13.2W/\textrm{mm}^2$) owing to high residual compressive stress and increasing mobility.

• 한국전기전자재료학회논문지
• /
• 제17권6호
• /
• pp.641-646
• /
• 2004

We report the changes of the microwave reflection coefficients S$_{11}$ of copper(II)-phthalocyanine (CuPc) thin films by using a near-field microwave microscope(NSMM) in order to understand the phase transition of CuPc. For a NSMM system, a high-quality microstrip resonator coupled with a dielectric resonator was used. CuPc thin films were prepared on the pre-heated glass substrates using a thermal evaporation method. The reflection coefficients S$_{11}$ of CuPc thin films were changed by the dependence on the substrate pre-heating temperatures. By comparing reflection coefficient S$_{11}$ and crystal structures, we found the phase transition of CuPc thin films from $\alpha$-phase to $\beta$-phase at the substrate heating temperature 200 $^{\circ}C$./TEX>.