• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.7
• /
• pp.576-579
• /
• 2009

This paper suggests a autonomous linear Li-ion battery charger which can safely distribute power between an external power source(AC adapter, auto adapter, or USB source), battery, and the system load. Depending on an external power source's capability, the charger selects proper charging-mode automatically. The charger IC designed and fabricated on Dongbu HITEC's $0.35{\mu}m$ BCD process with layers of one poly and three metals.

• Journal of the Korean Magnetic Resonance Society
• /
• v.7 no.2
• /
• pp.74-79
• /
• 2003

Li[Ni,Mn,Co]O$_2$ electrode has been studied by $\^$7/Li MAS NMR. A sharp resonance at -1 ppm and a very broad resonance at approximately 400 ppm are assigned to the Li ions in Co-only environment and Ni/Mn(Co) environment, respectively, indicating a segragation of Co ions and Ni/Mn ions. Different temperature behavior of the peak position is observed for Co-only environment and Ni/Mn(Co) environment. Oxidation of Ni ions is involved during the entire charging process. At high temperature, a peak narrowing caused by the electron hopping is observed.

• Journal of the Korean Chemical Society
• /
• v.45 no.3
• /
• pp.219-222
• /
• 2001

Separation of lithium isotopes was investigated by chemical ion exchange with a hydrous manganese(IV) oxide ion exchanger using an elution chromatography. The capacity of manganese(IV) oxide ion exchanger was 0.5 meq/g. The heavier lithium isotope was enriched in the solution phase, while the lighter isotope was enriched in the ion exchanger phase. The separation factor was determined according to the method of Glueckauf from the elution curve and isotopic assays. The separation factor of $^6Li^+$-$^7Li^+$ isotope pair fractionation was 1.018.

• Proceedings of the Korea Crystallographic Association Conference
• /
• 2002.11a
• /
• pp.15-15
• /
• 2002

Homogeneous and crack-free potassium lithium niobate (K₃Li/sub 2-x/Nb/sub 5+x/O/sub 15/, 0＜x＜0.5, KLN) single crystals were successfully grown by the Czochralski technique. The KLN single crystals of several different compositions were employed for the investigation of the lattice vibration spectra using infrared Raman spectroscopy. The characteristic Raman spectra of the [NbO/sub 6/]/sup 7-/ octahedral ions were strikingly influenced by the Li ion content. The symmetric stretch vibrational modes V₁, V₂ are broadened, and the symmetric bend vibration mode V/sub 5/ is broadened and even split into three peaks with increasing the Li content, supporting that the bend vibration modes of the [NbO/sub 6/]/sup 7-/ octahedrons are obviously perturbed by Li ions in the C site. Enhanced Raman peak intensities after the post annealing at 900℃ and for 24 h evidenced that a residual stress in as-grown crystals was negligible and only a defect concentration might be reduced.

• Journal of Electrochemical Science and Technology
• /
• v.7 no.4
• /
• pp.263-268
• /
• 2016

This study describes the effect of coating the $Li[Ni_{0.8}Co_{0.15}Al_{0.05}]O_2$ cathode surface with a homogeneous carbon layer produced by carbonization of polyvinylidene fluoride (PVDF) as a novel organic source. The phase integrity of the above cathode was not affected by the carbon coating, whereas its rate capability and cycling performance were enhanced. Similarly, the cathode thermal stability was also improved after coating, which additionally protected the cathode surface against the reactive electrolyte containing hydrofluoric acid (HF). The results show that coating the $Li[Ni_{0.8}Co_{0.15}Al_{0.05}]O_2$ cathode with carbon using the PVDF precursor is an effective approach to enhance its electrochemical properties.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.7
• /
• pp.2315-2319
• /
• 2012

To improve the performance of $LiFePO_4F$, a novel sol-gel process is developed. For comparison, ceramic process is also implemented. From X-ray diffraction results we know that each sample adopts a triclinic $P{\bar{1}}$ space group, and they are isostructural with amblygonite and tavorite. The scanning electron microscope images show that the homogeneous grains with the dimension of 300-500 nm is obtained by the sol-gel process; meanwhile the sample particles obtained by ceramic process are as big as 1000-3000 nm. By galvanostatic tests and at electrochemical impedance spectroscopy method, the sample obtained by sol-gel process presents better electrochemical properties than the one obtained by ceramic process.

• Electrical & Electronic Materials
• /
• v.10 no.7
• /
• pp.682-691
• /
• 1997

We have investigated the guided optical properties of a Ti:LiNbO$_3$optical waveguide which was fabricated by Ti-diffusion in an air atmosphere and proposed an effective polishing method of waveguide endfaces. And the results of guided optical mode and fabrication condition were obtained as follows; \circled1 propagation loss : 0.53 dB/cm \circled2 mode size : horizontal/vertical=12.5${\mu}{\textrm}{m}$ \circled3 mode mismatch : 1.7 dB \circled4 diffusion temperature : 105$0^{\circ}C$, time : 8 hours \circled5 atmosphere : air

• Electrical & Electronic Materials
• /
• v.10 no.1
• /
• pp.1-7
• /
• 1997

SAW filter has been used in mobile communication device, bandpass filter and resonator for merits )f miniaturization and high reliability. Materials for substrate mainly used single crystal such as LiNbO$_{3}$, LiTaO$_{3}$, ZnO. In this study, it was attempted that LiNbO$_{3}$ was substituted for piezoelectric ceramics(PZT4, PZT5A and PZT8) which had simple fabrication process because fabrication of crystal is difficult and it's cost is high. SAW filters were fabricated by the photolithography on piezoelectric ceramics substrates in order to compare their characteristics with LiNbO$_{3}$'s. The experimental value of center frequency was compared with theoretical one. The average difference of center frequency was 3.7%. PZT8 showed the best bandwidth properties among them. It is considered that PZT8 has higher mechanical quality factor and propagation velocity than others.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.18 no.1
• /
• pp.83-90
• /
• 2020

The Graphite Isotope Ratio Method (GIRM) can verify non-proliferation of nuclear weapon by estimating the total plutonium production in a graphite-moderated reactor. Using the reactor, plutonium is generated and accumulated through the ²³⁸U neutron capture reaction, and impurities in the graphite are converted to nuclides due to the nuclear reaction. Therefore, the amount of plutonium production and concentration of the impurities are correlated. However, the plutonium production cannot be predicted using only the absolute concentration of the impurities. It can only be predicted when the initial concentration of the impurities is obtained because the concentration, at a certain time, depends on it. Nevertheless, the ratios of the isotopes in an element are known regardless of the impurity of an element in the graphite moderator. Thus, the correlation between the isotope ratio and amount of plutonium produced helps predict plutonium production in a graphite-moderated reactor. Boron, Lithium, Chlorine, Titanium, and Uranium are known as indicator elements in the GIRM. To assess whether the correlation between the indicator isotope and amount of plutonium produced is independent of the initial concentration of the impurities, four different impurity compositions of graphite were used. ¹⁰B/¹¹B, ³⁶Cl/³⁵Cl, ⁴⁸Ti/⁴⁹Ti, and ²³⁵U/²³⁸U had a consistent correlation with the cumulative plutonium production, regardless of the initial impurity concentration of the graphite, because these isotopes were not generated through the nuclear reaction of other elements. On the other hand, the correlation between ⁶Li/⁷Li and plutonium production depended on the initial concentration of the impurities in graphite. Although ⁷Li can be produced through the neutron capture reaction of ⁶Li, the (n, α) reaction of ¹⁰B was the major source of ⁷Li. Therefore, the initial concentration of ¹⁰B affected the production of ⁷Li, making Li unsuitable as an indicator element for the GIRM.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.2
• /
• pp.193-204
• /
• 1998

The single crystal of the $LiTaO_3$has large electro-optic effects, so it is applied to optical switch, acousto-optic deflector, and optical memory device as hologram using photorefractive effect. In this study, optic-grade undoped $LiTaO_3$and Fe:LiTaO$LiTaO_3$single crystals were grown by the Czochralski method and optical transmission and absorption spectrums were measured in the wavelength of UV-VIS range. The curie temperature was determined with DSC and by measuring capacitance for the grown undoped crystal and ceramic powder samples of various Li/Ta ratio. In case of having a 48.6 mol% $Li_2O$ as a starting Li/Ta ratio, the results of concentration variations were below 0.01 mol% $Li_2O$ all over the crystal, so it was confirmed that $LiTaO_3$single crystals were grown under congruent melting composition having optical homogeneity. The curie temperature of the Fe:$LiTaO_3$crystal was increased with increased with increased doped Fe concentrations;by the ratio of $7.5^{\circ}C$ increase per Fe 0.1 wt%. Also, the optical transmittance was about 78 %, which was sufficient for optical device.