• Journal of the Korea Concrete Institute
• /
• v.13 no.4
• /
• pp.336-345
• /
• 2001

The construction of underwater structures has been increased, but underwater concrete hassome problems of quality deterioration and contamination around in-situ of civil and architecture; therefore, new materials and methods for them are demanded. In this paper in-situ application of underwater antiwashout concrete which is manufactured for trio purpose of not only decreasing suspended solids and the heat of hydration but also increasing long term strength was studied. In the case of mock-up test(Ⅰ), when underwater antiwashout concrete, whose slump flow was 58 cm, was placed in the mock-up test at a speed of 24 ㎥/hr, it took about a minute to flow to the side wall, and the surface was maintained at horizontal level. In this case, compressive strength of the core specimens in each section was higher than the standard design compressive strength of 240 kgf/㎠. In the case of mock-up test(II), pH value and suspended solids of high strength underwater antiwashout concrete were 10.0∼11.0 and 51 mg/ℓ at 30 minutes later, initial and final setting time were about 30, 37 hr, and the slump flow of that was 53$\pm$2 cm. In the placement at a speed of 27 ㎥/hr, there was no large difference in flowing velocity, with or without reinforcement and flowing slope was maintained at horizontal level. In this case, compressive strength and elastic modulus of the core specimens somewhat decreased as flowing distance was far : however, those of central area showed the highest value.

• Journal of Environmental Science International
• /
• v.29 no.3
• /
• pp.229-240
• /
• 2020

This study was conducted to evaluate the effect of phosphorus acid (H₃PO₃) addition to the horticultural bed soil on the initial growth of red pepper (Capsicum annuum L. cv.), cucumber (Cucumis sativus L. cv.), and kimchi cabbage (Brassica campestris L. ssp. pekinensis (Lour.) Rupr. cv.). The stem heights of red pepper and cucumber were 46.1% and 23.0% greater in the 50 mg/L of phosphorus acid treatment than the untreated (control). Further, the stem diameter of pepper and cucumber were 48.7% and 23.0% greater in the 50 mg/L of phosphorus acid treatment than the control. In addition, the number of kimchi cabbage leaves was 47.5% greater in the 50 mg/L of phosphorus acid treatment than the control. The dry weights of red pepper, cucumber and kimchi cabbage were 72.9%, 16.5%, and 30.4% heavier in the 50 mg/L than the control, respectively. Cations (K, Ca, and Mg) and total phosphorus (T - P) were quantitatively analyzed for these three horticultural crops. The concentrations of K, Ca, and Mg, and T - P were higher in the 50 mg/L of phosphorus acid than the control, respectively. Based on the results obtained in this study, it appears that treatment of phosphorus acid in horticultural bed soil enhanced the growth of red pepper, cucumber and Kimchi cabbage.

• KSBB Journal
• /
• v.22 no.6
• /
• pp.409-413
• /
• 2007

Polydiacetylene(PDA)-based sensors possess a number of properties that can be successfully applied for label-free detection system. PDA is one of the most attractive color-generating materials, with growing applications as sensors. Here we introduce various PDA-based devices, used as biosensor, chemosensor, thermosensor, and optoelectronics sensor. In general, PDA liposomes and films are closely packed and properly designed for polymerization via 1,4-addition reaction to form an ene-yne alternating polymer chain. PDA-based two/three dimensional structures have been used for colorimetric or fluorescent devices, sensing biological as well as chemical components. This color-generating material also present a very high charge carrier mobility, allowing its application as field-effect transistor (FET). The immobilized PDA structures or films have distinct advantages for the detection of low concentration target molecules over the aqueous solution-based detection systems. In the present review, reported detection methods by using various PDA structures are summarized with updated references.

• Journal of Biomedical Engineering Research
• /
• v.21 no.3 s.61
• /
• pp.261-271
• /
• 2000

The present study investigated flow dynamics of a two-dimensional abdominal aortic bifurcation model under sinusoidal flow conditions considering wall motion. impedance phase angle(time delay between pressure and flow waveforms), and non-Newtonian fluid using computational fluid dynamics. The wall shear stress showed large variations in the bifurcated region and the wall motion reduced amplitude of wall shear stress significantly. As the impedance phase angle was changed to more negative values, the mean wall shear stress (time-averaged) decreased while the amplitude (oscillatory) of wall shear stress increased. At the curvature site on the outer wall where the mean wall shear stress approached zero. influence of the phase angle was relatively large. The mean wall shear stress decreased by $50\%$ in the $-90^{\circ}$ phase angle (flow wave advanced pressure wave by a quarter period) compared to the $0^{\circ}$ phase angle while the amplitude of wall shear stress increased by $15\%$. Therefore, hypertensive patients who tend to have large negative phase angles become more vulnerable to atherosclerosis according to the low and oscillatory shear stress theory because of the reduced mean and the increased oscillatory wall shear stresses. Non-Newtonian characteristics of fluid substantially increased the mean wall shear stress resulting in a less vulnerable state to atherosclerosis.

• Koreanishche Zeitschrift fur Deutsche Sprachwissenschaft
• /
• v.3
• /
• pp.35-55
• /
• 2001

In der Semiotik ist es sehr wichtig, den Rahmenbereich des Zeichens festzustellen, weil der Bereich des Zeichens je nach Wissenschaftler unterschiedlich ist. Dementsprechend muss jedes Forschungsergebnis in der Semiotik hinterfragt werden, um sichergehen zu $k\"{o}nnen$, ob es zur Semiotik $geh\"{o}rt$ oder nicht. Daher besteht $zun\"{a}chst$ die Notwendigkeit, zu bestimmen, was ein Zeichen ist. In diesem Zusammenhang versuchten wir in diesem Aufsatz, damit wir den Begriff 'Zeichen' besser erfassen $k\"{o}nnen$. das Zeichen von C. S. Peirce mit dem van W. v. Humboldt zu vergleichen. Zu Beginn dieses Aufsatzes stellten wir dar, was ein Zeichen ist. Dieser Vorgang ist notwendig, damit mit Hilfe des allgemeinen Begriffes des Zeichens ein Vergleich zwischen Peirce und Humboldt angestellt werden kann. Danach stellten wir die Zeichentheorie von Peirce vor. Nach Peirce ist die Sprache eine Untergattung von drei Zeichensorten, die Ikon, Index und Symbol genannt werden. Nach ihm gehbrt das Symbol zur Sprache. $F\"{u}r$ ihn ist der Interpretant im Zeichenbegriff am wichtigsten, weil ein Zeichen immer eines Interpretantes bedarf, der das Zeichen interpretiert. Aber der Interpretant ist kein Individuum, sondern ein interpretierendes $Bewu{\ss}tsein$, also eine traditionelle Gesellschaft, die ein Muster zum Interpretieren bietet. $Anschlie{\ss}end\;besch\"{a}ftigten$ wir uns mit der Theorie von Humboldt. Er benutzt verschiedene Zeichenbegriffe wie z.B. Schriftzeichen, Lautzeichen, Sprachzeichen, grammatische Zeichen, $h\"{o}rbare$ Zeichen, zeitliche Zeichen und $r\"{a}umliche$ Zeichen. Bei ihm ist die Unterscheidung zwischen Wort und Zeichen besonders wichtig, weil das Wort nicht zum Zeichen $geh\"{o}rt$, wie wir es normalerweise annehmen. Er behauptet, dass das Wort beim Produzieren motiviert ist. Daher ist nach ihm das Wort transsemiotisch. $Dar\"{u}ber$ hinaus muss das Zeichen und das Wort im Zusammenhang zwischen Sprache und Denken betrachtet werden. Wenn man das Wort als Zeichen betrachtet, ist das Wort ein Zwischending zwischen dem Sprechenden und dem Ding. Damit $k\"{o}nnen$ wir schlussfolgern; 1) Bei Humboldt ist das Zeichen em Mittel zum Denken, das sich vom transsemiotischen Wort unterscheidet. 2) Nach Peirce besteht ein Zeichen aus Ikon, Index und Symbol. Im Zeichen, das aus Reprasentamen, Interpretant und Objekt besteht, ist der Interpretant am wichtigsten, denn ein Zeichen, dass keinen Interpretant hat, ist kein Zeichen mehr, das interpretierbar ist.

• Journal of the Korean Society of Safety
• /
• v.31 no.3
• /
• pp.8-15
• /
• 2016

The purpose of this study is to design a model with the structural stability so as not to lose the operational function due to structural plastic or fail of a sliding blast door by blast pressure to this aim, a numerical simulation was performed using full-size experiments and M&S (Modeling & Simulation) of the sliding blast door. The sliding blast door ($W3,000{\times}H2,500mm$) under the blast load is in the form of a sliding type 2-way metal grill, which was applied by a design blast pressure (reflected pressure $P_r$) of 17 bar. According to the experimental results of a real sliding blast door under blast load, the blast pressure reached the sliding blast door approximately 4.3 ms after the explosion and lasted about 4.0 ms thereafter. The maximum blast pressure($P_r$) was 347.7 psi (2,397.3 kPa), it is similar to the UFC 3-340-02 of Parameter(91 %). In addition, operation inspection that was conducted for the sliding blast door after real test showed a problem of losing the door opening function, which was because of the fail of the Reversal Bolt that was installed to prevent the shock due to rebound of the blast door from the blast pressure. According to the reproduction of the experiment through M&S by applying the blast pressure measurement value of the full-size experiments, the sliding blast door showed a similar result to the full-size experiment in that the reversal bolt part failed to lose the function. In addition, as the pressure is concentrated on the failed reversal bolt, the Principal Tensile Failure Stress was exceeded in only 1.25 ms after the explosion, and the reversal bolt completely failed after 5.4 ms. Based on the result of the failed reversal bolt through the full-size experiment and M&S, the shape and size of the bolts were changed to re-design the M&S and re-analyze the sliding blast door. According to the M&S re-analysis result when the reversal bolt was designed in a square of 25 mm ($625mm^2$), the maximum pressure that the reversal bolt receives showed 81% of the principal tensile failure stress of the material, in plastic stage before fail.

• Restorative Dentistry and Endodontics
• /
• v.34 no.6
• /
• pp.467-476
• /
• 2009

The aim of this study was to measure the dentinal tubular fluid flow (DFF) during and after amalgam and composite restorations. A newly designed fluid flow measurement instrument was made. A third molar cut at 3 mm apical from the CEJ was connected to the flow measuring device under a hydrostatic pressure of 15 $cmH_2O$. Class I cavity was prepared and restored with either amalgam (Copalite varnish and Bestaloy) or composite (Z-250 with ScotchBond MultiPurpose: MP, Single Bond 2: SB, Clearfil SE Bond: CE and Easy Bond: EB as bonding systems). The DFF was measured from the intact tooth state through restoration procedures to 30 minutes after restoration, and re-measured at 3 and 7days after restoration. Inward fluid flow (IF) during cavity preparation was followed by outward flow (OF) after preparation, In amalgam restoration, the OF changed to IF during amalgam filling and slight OF followed after finishing. In composite restoration, application CE and EB showed a continuous OF and air-dry increased rapidly the OF until light-curing, whereas in MP and SB, rinse and dry caused IF and OF, respectively. Application of hydrophobic bonding resin in MP and CE caused a decrease in flow rate or even slight IF. Light-curing of adhesive and composite showed an abrupt IF. There was no statistically significant difference in the reduction of DFF among the materials at 30 min. 3 and 7 days after restoration (p > 0.05).

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 1998.05a
• /
• pp.60-60
• /
• 1998

아연도금강판은 내식성이 우수하여 자동차용 강판으로 널리 쓰이고 있다. 자동차용 강판은 spot 용접에 의해서 각 부분들이 접합되는데 도금층으로 사용되는 아연은 강판보다 융점이 낮아서 용접작업을 저하시킨다. 현재 사용되는 작업조건에서 용접 타 접수가 평균 2000회를 넘게되면 용접되는 부위의 면적이 감소되어 접합강도가 떨어지게된다. 따라서, 아연이 도금된 강판을 용접하게되면 작업성이 저하되므로 도금층의 성분에 대한 변화를 주므로서 이에 대한 개선을 할 필요가 있다.. Cole, Dickenson 및 Kimchi 등은 도금충내의 알루미늄을 0.1~0.5%(중량비) 함유하는 아연도금강판은 저항용접시 도금충내의 알루미늄 함량에 따라 용접성이 영향을 받는다고 보고하였다. 전극수명은 도금층내의 알루미늄 함량이 증가할수록 떨어지는데 알루미늄이 0.5% 이 하로 함유된 아연도금강판의 경우는 용접타접수가 2000~6000회에 이르르나 알루미늄 이 50%이상 함유된 합금도금강판은 200-600회에 불과한 것으로 나타난다. H. M Matsuda 등은 도금층의 알루미늄이 용접성에 영향을 미치는 이유로서 도금층의 용융 온도 변화를 지적하였다. 도금충내에 알루미늄의 함량이 높게되면 철과 아연의 확산에 의한 합금화 반응이 저하되어 도금층의 용융온도가 높아지지 못하므로 용접성이 나빠지게 된다. 본 연구에서는 아연도금욕의 조성은 기존의 상태로 유지하고 제3의 원소를 첨가하여 도금층에 함유되는 알루미늄의 양에 미치는 효과를 조사하였다. 도금층의 불성변화 및 그에 따른 내식성을 조사하였으며 도금층의 조직변화도 함께 관찰하였다. 아울러 첨가원소에 의한 도금욕의 특성도 평가하였다. 첨가원소에 의해서 도금충내의 알루미늄 함량은 감소하는 경향을 나타내었으며 도금층의 물성은 주어진 조성범위 내에서 별다른 변화를 나타내지 않았다.brittlement)기구도 제안되고 었다. 원전의 냉각수는 고 순도의 물이지만 수 처리 과정과 웅축기 배관의 누수로 인한 산소, $Cu^{2+},{\;}S_xO_6{\;}^{2-}(x=3~6)$ 등이 유입되어 오염되는데 이려한 오염물질들이 수 ppm정도 소량 포함된 경우 응 력부식민감도는 상당히 증가된다. 산성분위기 흑은 산소, $Cu^{2+}$, 등이 소량 포합된 산화성 분위기 그리고 sufur oxyanion 에 오염된 고온의 물에서 600 의 IGSCC 민감도는 예민화도가 증가할 수록 민감하여 304 의 IGSCC 와 매우 유사한 거동을 보인다. 본 강연에서는 304 와 600 의 고온 물에서 일어나는 IGSCC 민감도에 미치는 환경, 예민화처리, 합금원소의 영향을 고찰하고 이에 대한 최근의 연구 동향과 방식 방법을 다룬다.다.의 목적과 지식)보다 미학적 경험에 주는 영향이 큰 것으로 나타났으며, 모든 사람들에게 비슷한 미학적 경험을 발생시키는 것 이 밝혀졌다. 다시 말하면 모든 사람들은 그들의 문화적인 국적과 사회적 인 직업의 차이, 목적의 차이, 또한 환경의 의미의 차이에 상관없이 아름다 운 경관(High-beauty landscape)을 주거지나 나들이 장소로서 선호했으며, 아름답다고 평가했다. 반면에, 사람들이 갖고 있는 문화의 차이, 직업의 차 이, 목적의 차이, 그리고 환경의 의미의 차이에 따라 경관의 미학적 평가가 달라진 것으로 나타났다.corner$적 의도에 의한 경관구성의 일면을 확인할수 있지만 엄밀히 생각하여 보면 이러한 예의 경우도 최락의 총체적인 외형은 마찬가지로 $\ulcorner$순응$\lrcorner$의 범위를 벗어나지 않는다. 그렇기 때문에도 $\ulcorner$

• The Korean Journal of Physiology
• /
• v.24 no.2
• /
• pp.249-260
• /
• 1990

Maximal cardiac output and oxygen uptake $(VO_{2max})$ were measured during treadmill exercise for seven top-class marathoners and nine non-athletes using impedance cardiograph developed by one of the authors (DW Kim). Results of this study are summarized as belows. 1) New shoes with sponge and silicon rubber attached to the soles were developed to reduce motion artifact during treadmill exercise. Ensemble everaging techneque with the developed shoes was also used to improve the measurement of stroke volume using impedance cardiography. 2) Maximal cardiac output of the athletes, 14.98 L/min, was significantly higher than that of the non-athletes, 13.46 L/min. As maximal heart rate of the marathoners is lower than that of non-athletes, stroke volume of the former is significantly larger than that of the latter. 3) $VO_{2max}$ of the marathoners, 59.38 ml/kg/min, was higher than that of the non-athletes, 40.22 ml/kg/min. At the anaerobic threshold. $VO_{2max}$ of the former was 62.3% of $VO_{2max}$ and this was significantly higher than that of the non-athletes, 57.2%, This results indicates that the marathoners have higher aerobic capacity than the non-athletes. 4) The marathoners showed larger $VO_2$ than the non-athletes at the same cardiac output, indicating that a-v $O_2$ of the former is higher than that of the latter. 5) Maximal systolic pressure of the marathoners was higher than that of the non-athletes, and so was maximal rate-pressure products. These results indicate that heart oxygen consumption rate $(hVO_2)$ of the marathoner is higher than that of the non-athletes is mainly due to higher stroke volume. And higher oxygen consumption of the marathoners is due to higher stroke volume. And higher oxygen consumption of the marathoners is due to their larger a-v $O_2$. The marathoners show both higher threshold and $VO_{2max}$. Especially, measurement of cardiac output during treadmill exercise by improved impedance cardiography is expected to contribute in study of cardiac function of athletes.

• Korean Journal of Psychosomatic Medicine
• /
• v.3 no.2
• /
• pp.139-146
• /
• 1995

Forty patients meeting DSM-III-H criteria for panic disorder and 51 normal controls were assessed with the Personality Diagnostic Questionnaire-Revised(PDQ-R), a self-rating scale designed to assess Axis II personality disorders and traits. Results replicated previous findings of a preponderance of dependent, avoidant, and histrionic features. But our result showed other features such as paranoid, schizotypal, borderline, and antisocial traits also. Patients were divided into two groups according to the severity of their personality traits(high or low). These groups were compared in various panic symptomatology and SCL-90-R. None of the specific symptom dimensions in panic disorder, i.e. panic, anxiety, agoraphobia, social impairment, or chronicity was different between groups. Rather, high personality trait groups were found to have significantly more symptomatology in SCR-90-R than low personality groups. Result indicated that patients exhibiting a greater number of personality traits were also significantly more symptomatic. The results suggested a possible link beteween panic disorder and personality disorder. And, general factors such as depression, social or interpersonal sensitivity might provide a much better explanation of personality disorders in panic patients.