• 대한치과기공학회지
• /
• 제24권1호
• /
• pp.95-104
• /
• 2002

For biomedical applications, Ti-X%Zr-Y%Nb-0.2%Pd(X:10$\sim$20, Y:2$\sim$8) alloys not containing harmful Al and V were newly designed, and the effect of alloy composition and heat treatment on the microstructure and mechanical properties was investigated. From the results, it was shown that the mechanical properties were enhanced with the addition of Zr or Nb. The effect of heat treating on room temperature strength was investigated by aging treatment after solution treatment. The mechanical properties of Ti-20%Zr-4%Nb-0.2%Pd alloy aged at 400$^{\circ}C$ for 10hrs was found to be superior to those of the pure Ti and Ti-6%Al-4%V ELI alloy.

• 한국표면공학회지
• /
• 제54권4호
• /
• pp.178-183
• /
• 2021

The temperature and frequency dependence of the dielectric constant of the BaTiO₃ substituted with two types of donor dopants, Nb⁵⁺ and Ta⁵⁺, respectively, were compared and analyzed. Dielectric specimens of four specific compositions, Ba_0.95Nb_0.05TiO₃, Ba_0.90Nb_0.10TiO₃, Ba_0.95Ta_0.05TiO₃, and Ba_0.90Ta_0.010TiO₃ were prepared by calcining at 1100 ℃ and sintering at 1300 ℃ to have a perovskite structure to measure capacitance. XRD and SEM analysis were used to observe the structure, with particular focus on the integration into the Nb⁵⁺ and Ta⁵⁺ substituted BaTiO₃ crystal lattice. X-ray diffraction peaks in the (200) and (002) planes were observed between 45.10° and 45.45° of the BaTiO₃ solid solution substituted with different fractions of Nb⁵⁺ and Ta⁵⁺. The dielectric properties were analyzed and the relationship between the properties and structure of the substituted BaTiO₃ was established. The fine particles and high density of the substituted BaTiO₃ were maintained like pure BaTiO₃, and in particular, a shift toward the low temperature side of the phase transition temperature range was clearly found, unlike pure BaTiO₃. In addition, the phase transition at a temperature higher than the Curie temperature relatively satisfies the modified Curie-Weiss law.

• 한국해양공학회지
• /
• 제25권4호
• /
• pp.66-71
• /
• 2011

The flexural strength of $MoSi_2$ based composites reinforced with Nb sheets has been investigated, based on the detailed examination of their microstructure and fractured surface. Both sintered density and porosity of Nb/$MoSi_2$ composites were also examined. Nb/$MoSi_2$ composites were fabricated by different conditions such as temperature, applied pressure and its holding time, using a hot-press device. The volume fraction of Nb sheet in this composite system was fixed as 10%. The characterization of Nb/$MoSi_2$ composites were investigated by means of optical microscopy, scanning electron microscope and three point bending test. Nb/$MoSi_2$ composites represented a dense morphology at the interfacial region, accompanying the creation of two types of reaction layer by the chemical reaction of Nb and $MoSi_2$. Nb/$MoSi_2$ composites possessed an excellent density at the fabricating temperature of $1350^{\circ}C$, corresponded to about 95% of theoretical density. The flexural strength of Nb/$MoSi_2$ romposites were greatly affected by the pressure holding time at the same fabricating temperature, owing to the large suppression of porosity in the microstructure. Especially, Nb/$MoSi_2$ composites represented a good flexural strength of about 310 MPa at the fabricating condition of $1350^{\circ}C$, 30MPa and 60min, accompanying the pseudo-ductile fracture behavior by the deformation of Nb sheet and the interfacial delamination.

• The Korean Journal of Ceramics
• /
• 제6권3호
• /
• pp.272-275
• /
• 2000

Starting from the stoichiometric composition of $K_2$CO$_3$: Li$_2$CO$_3$: Nb$_2$O$_5$=3 : 2 : 5 with the mole ratio, $K_3$LiNb$_6$O$_17$ 17/ single crystals were grown using the Czochralski method. Although the starting melt composition corresponds to the $K_3$Li$_2$Nb$_5$O$_15$ crystals, the chemical composition of the as grown crystals appears to be $K_2.95$Li$_1.33$Nb$_6.17$O$_17$ or $K_2.60$Li$_1.17$Nb$_{5.44}$ 5.44/O$_{15}$ which relatively contain fewer Li ions than $K_3$Li$_2$Nb$_5$O$_15$ crystals. We investigated the influence of the deficiency of the Li ions in the tetragonal tungsten bronze structure through the measurements of DE loop, temperature dependent dielectric constant, differential thermal analysis and temperature dependent X-ray diffraction pattern.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.205-205
• /
• 2008

PZT 세라믹은 우수한 유전 및 압전특성을 갖고 있어 변압기, 센서 및 엑츄에이터 등에 널리 응용되고 있다. 그러나, 우수한 특성에도 불구하고 PZT세라믹스의 소결시 PbO의 높은 유독성 및 휘발로 인하여 환경오염을 야기 시킨다. 그러므로 PbO로 구성된 세라믹을 대체하기 위한 우수한 압전특성을 가진 비납계 세라믹스 개발이 연구의 주류를 이루고 있다. 그 중 비납계 NKN와 BZT는 대체물질로 많이 관심을 받고 있다. 이는 일반적인 NKN조성은 우수한 압전성과 높은 큐리온도를 가지고 있을 뿐만 아니라, BZT조성의 Zr성분이 큐리온도를 낮추거나 유전특성을 졸게 하여 유전율 곡선을 완화하게 하는 특징이 있다. 하지만 NKN은 $1140^{\circ}C$이상의 소결온도에서 K의 휘발특성으로 인해 소성 후에도 주변의 수분을 흡수하는 조해성이 발생하는 문제가 발생한다. 그래서 본 연구에서는 낮은 온도에서 NKN계 세라믹스의 밀도를 증가시킬 뿐만 아니라, 우수한 유전 및 압전특성을 갖는 세라믹스를 제조하고자 비납계 $0.94(K_{0.5}Na_{0.5})NbO_3-0.06Ba(Zr_{0.05}Ti_{0.95})O_3$ (NKN-BZT)의 조성을 사용하였고 소결조제로는 $MnO_2$, NiO, $Bi_2O_3$, ZnO, $Li_2CO_3$, CuO등을 변화주어 유전 및 압전 특성을 알아보았다.

• 한국결정학회지
• /
• 제17권1호
• /
• pp.24-32
• /
• 2006

[ $Zn_3Nb_2O_8$ ]세라믹스에 액상소결제인 $V_2O_5$를 첨가하여 소결하여 고주파 대역에서의 유전특성의 변화를 조사하였다. $1100^{\circ}C$에서 2시간 하소한 결과 $Zn_3Nb_2O_8$를 합성할 수 있었고, $V_2O_5$를 첨가하여 소결한 $Zn_3Nb_2O_8$에서 $V_2O_5$의 mole%증가와 소결온도의 증가에 따라 상대밀도 95%의 소결특성을 확인 하였다. 유전율 특성은 $V_2O_5$ mole ratio가 $2{\sim}4%$의 시편에서 모두 ${\varepsilon}_r\;21$ 이상으로 증가됨을 확인하였고, 품질계수는 $900^{\circ}C$에서 소결한 $V_2O_5$ 2 mole% 시편에서 $Q{\times}f=40,000$을 나타내었다. 온도계수는 $900^{\circ}C$ 소결하고 $V_2O_5$ 1 mole% 첨가한 경우 0에 제일 가까운 $T_{cf}=-54ppm/^{\circ}C$를 나타내었고, 다른 보건에서는 $T_{cf}=-60{\sim}-80ppm/^{\circ}C$의 값을 나타내었다.

• 한국세라믹학회지
• /
• 제33권11호
• /
• pp.1267-1275
• /
• 1996

Green sheet was prepared by tape casting in the composition of (1-x)Pb(Mg1/3Nb2/3)O3-PbTiO3 system using Pb(Mg1/3Nb2/3)O3 and PbTiO3 synthesized with PbO, Nb2O5 MgO and TiO2 The densest green sheet was obtained in the weight ratio 70:30 of powder to binder. Green sheet wasmultilayered in metal mould and formed into lamination at 7$0^{\circ}C$, 300kg/cm2 The lamination was sintered at 110$0^{\circ}C$ 2hr, Dielectric constant and Curie temperature of disc type sintered body was highered with increasing the amount of PbTiO3 and was in the range of 19000-21000, -7~45$^{\circ}C$ respectively. Green and sintered relative density of lamination was 61% and 95% respectively.

• 한국표면공학회지
• /
• 제52권4호
• /
• pp.211-226
• /
• 2019

Optical thin films were deposited by using a reactive pulsed DC magnetron sputtering method with a high density plasma(HDP). In this study, the effect of sputtering process conditions on the microstructure and optical properties of $SiO_2$, $TiO_2$, $Nb_2O_5$ thin films was clarified. These thin films had flat and dense microstructure, stable stoichiometric composition at the optimal conditions of low working pressure, high pulsed DC power and RF power(HDP). Also, the refractive index of the $SiO_2$ thin films was almost constant, but the refractive indices of $TiO_2$ and $Nb_2O_5$ thin films were changed depending on the microstructure of these films. Antireflection films of $Air/SiO_2/Nb_2O_5/SiO_2/Nb_2O_5/SiO_2/Nb_2O_5/Glass$ structure designed by Macleod program were manufactured by our developed sputtering system. Transmittance and reflectance of the manufactured multilayer films showed outstanding value with the level of 95% and 0.3%, respectively, and also had excellent durability.

• 열처리공학회지
• /
• 제35권2호
• /
• pp.88-95
• /
• 2022

Titanium alloy for bio-medical applications have been developed to reduce the toxicity of alloying elements and avoid the stress-shielding effect which is caused by relatively high elastic modulus compared to bone. Ti-39Nb-6Zr (TNZ40) alloy of elastic modulus exhibits around 40 GPa in the case of beta single phase. However, the strength of this alloy is lower than the other types of titanium alloys. Many research found that adding oxygen to beta-titanium alloys is beneficial for improving the strength through solid solution strengthening. In this study, TNZ40 ingots with addition of O were prepared by an arc remelting process (Ti-39Nb-6Zr-0.16O (wt.%), Ti-39Nb-6Zr-0.26O (wt.%)). Thermo-mechanical processing (i.e., heat treatment, cold swaging and aging heat treatment) has been performed under various conditions. Therefore, the aim of this study is to investigate the effect of oxygen content and ω phase formation on microstructure and mechanical properties.

• Journal of the Optical Society of Korea
• /
• 제8권2호
• /
• pp.90-95
• /
• 2004

The structure of Ti:LiNbO$_3$optical waveguide with a mode size far different from that of single mode optical fiber has been optimized by tapering the waveguide ends. This work was focused on determining the optimized sets of parameters for the fabrication of low-loss Ti indiffused optical waveguides in LiNbO$_3$. Numerical and analytical modeling were applied to simulate the guiding quality and to determine the mode sizes. Based on these modeling results, new waveguide structures with tapered ends have been defined, fabricated and characterized in the respect of the coupling of fiber to Ti-indiffused LiNbO$_3$waveguide.