한국신재생에너지학회:학술대회논문집
Korean Society for New and Renewable Energy (KSNRE)
- Semi Annual
Domain
- Energy/Resources > New and Renewable Energy
2011.05a
-
본 연구에서는 PV cell이 직달 일사에 노출되는 경우와 집광된 태양광에 조사되는 경우의 성능을 비교하는 한편 집광기의 형태에 따른 열적 성능을 검토하고자 하였다. PV cell은 본질적으로 반도체의 특성을 가지므로 작동온도의 상승에 따라 성능이 저하된다는 사실이 알려져 있으며, 태양조사의 강도 및 밀도 등 특성에 따라서도 성능의 변화를 예상할 수 있다. 그러나 이러한 성능변화에 관련된 인자들과 그 영향의 크기에 대한 정량적인 기술자료가 부족하므로 설치와 이용에 한계가 있는 것이 현실이다. 인공태양 장치(solar simulator)를 이용하여 0.7에서 1.2 sun 범위의 태양 조사 환경에서 결정질 실리콘계 PV cell과 집광형 PV cell의 성능을 검토하였다. 집광에 사용한 PTC는 집광면적의 폭이 500 mm이며, 집광 조사면적이 최소 10 mm인 경우 이론적 최대 집광비가 50이었다. PTC의 축방향으로는 균일한 태양조사가 있게된다는 것을 가정하여 모델의 길이는 간편한 실험을 위해 150에서 500 mm의 범위에서 제작하였다. 수평으로 놓인 PTC의 상부 초점 위치로부터 집광면이 아래 쪽에 위치할수록 집광 조사 면적이 증가하므로 PV cell의 크기에 따라 PTC 초점의 위치로부터 거리를 결정하였다. 한편, PTC 자체의 성능도 촛점거리와 집광면 폭의 비에 따라 달라질 수 있다는 가정 하에, 포물면의 최저 위치로부터 촛점거리는 각각 300, 400 및 500 mm가 되도록 세가지 형태를 제작하여 사용하였다. 동일한 형태의 PTC에서 PV cell의 동일한 설치 위치에서도 최고
$110^{\circ}C$ 범위의 PV cell의 작동 (표면) 온도에 따른 성능의 차이를 관찰하기 위해 셀의 후면을 냉각시키는 경우와 그렇지 않은 경우를 비교하였다. PV cell의 표면 온도 측정을 위해서, 후면의 온도와 같이 광선 차단 효과의 우려가 없는 경우에는 열전대를 설치하였으며, 셀의 전면 온도 측정을 위해서는 비접촉식 적외선 온도계를 사용하였다. 냉각 방법으로는 공기를 이용한 자연대류와 액체를 사용하는 강제대류의 경우를 고려하였으며, 필요에 따라 적절히 설계된 히트싱크를 설치하여 비교 실험을 진행하였다. 강제대류 냉각의 경우는 항온조를 사용하여 순환하는 냉각수의 유량과 공급온도를 변화시킴으로써 PV cell의 작동온도를 조절하고, 이에 따른 발전 성능의 변화를 관찰하였다. 본 연구에서 도출한 실험 및 분석 결과는 PV cell의 설치 환경과 작동온도의 변화에 따라 그 성능 변화를 예측할 수 있는 기술적 자료를 제공함으로써 에너지 이용의 합리화를 도모하는데 기여할 수 있을 것이다. -
태양열 발전 플랜트에 사용되는 중고온 범위의 축열조에 고체-액체간 상변화를 수행하는 용융염을 축열물질로 사용하면 액체상 또는 고체상만으로 된 열저장 매체에 비해 축열조의 규모를 축소함과 동시에 축열온도의 균일성 향상에 기여할 수 있다. 중온인
$250{\sim}400^{\circ}C$ 범위에서 이용 가능한 용융염으로는 질산칼륨($KNO_3$ ), 질산리튬($LiNO_3$ )등이 있다. 그러나 이러한 용융염의 가장 큰 단점은 열전도율이 매우 낮다는 것이며, 이로 인해 요구되는 열전달률을 성취하기 위해서는 많은 열접촉면적이 필요하다는 것이다. 이러한 단점을 극복하는 방법을 도입하지 않고서는 축열시스템의 소규화를 성취하는데 큰 효과를 가져올 수 없다. 한편 열수송 성능이 탁월한 히트파이프를 사용하면 열원 및 열침과 축열물질 사이의 열전달 효율을 증가시켜 시스템의 성능 향상과 동시에 소규모화에 기여할 수 있다. 중온 범위 히트파이프의 작동유체로서 다우섬-A(Dowtherm-A)는$150^{\circ}C$ 이상$400^{\circ}C$ 까지의 범위에서 소수에 불과한 선택적 대안 중 하나이다. 따라서 본 연구에서는 용융염을 사용하는 중온 태양열축열조에 적용 가능한 다우섬-A 히트파이프의 성능을 파악하여 기술적 자료를 제시하고자 하였다. 열원으로는 고온 고압의 과열증기, 그리고 열침으로는 중온의 포화증기를 고려하였다. 용융염 축열조를 수직으로 관통하는 히트파이프는 하단부에서 열원 증기와 열교환 가능하며, 중앙부에서 축열물질과 열교환하고, 상단부에서는 중온 증기와 접촉할 수 있도록 배치하였다. 축열모드에서는 히트파이프의 하단부가 증발부로 작동하고, 중앙부가 응축부로 작동하여 용융염으로 열을 방출하면 용융염의 온도가 상승하고 용융점에 도달하면 액상으로의 상변화가 진행되면서 축열이 활성화된다. 축열모드에서 히트파이프의 상단부는 단열부로 작동한다. 방열과정에서는 히트파이프의 하단부가 단열된 상태이고, 중앙부는 용융염으로부터 열을 받아 증발부로 작동하며, 상단부는 중온 증기로 열을 방출하므로 응축부로 작동한다. 즉, 축열시스템의 작동모드에 따라 하나의 히트파이프에서 증발부, 응축부, 단열부의 위치가 변하게 된다. 특히, 히트파이프의 중앙 부분이 응축부에서 증발부로 전환될 때에도 작동이 보장되려면 내부 작동유체의 연속적인 재순환이 가능해야 하므로, 일반 히트파이프에서와는 달리 초기 작동액체의 충전량을 증발부 전체의 체적보다 더 많이 과충전해야 한다. 이러한 히트파이프의 성능 파악을 위한 실험에서 고려한 변수들은 열부하, 작동액체의 충전률, 작동온도 등이며, 열수송 성능의 지표로서는 유효열전도율과 열저항을 이용하였다. 중온범위에서 적정한 작동온도를 성취하기 위해 실험에서는 전압 조절기로 열부하를 조절하는 동시에 항온조로 응축부의 냉각수 입구 온도를 제어하였다. 하나의 히트파이프에 대해서 최대 1 kW까지의 열부하에서 냉각수 입구 온도를$40^{\circ}C$ 에서$80^{\circ}C$ 범위로 변화시키면 히트파이프 작동온도를 약$250^{\circ}C$ 내외로 조절 가능하였다. 히트파이프 작동액체 충전률은 윅구조물의 공극 체적을 기준으로 372%에서 420%까지 변화 시켰다. 실험 결과를 토대로 열저항과 유효 열전도율을 각각 입력 열유속, 작동온도, 작동액체 충전률 등의 함수로 제시했다. 동일한 냉각수 온도에서는 충전률이 높을수록 히트파이프의 작동온도가 감소하였다. 열저항 값의 범위는 최소$0.12^{\circ}C/W$ 에서 최대$0.15^{\circ}C/W$ 까지로 나타났으며 유효 열전도율의 값은 최소$7,703W/m{\cdot}K$ 에서 최대$8,890W/m{\cdot}K$ 까지 변화했다. 최소 열저항은 충전률 420%인 경우에 나타났는데 이때의 작동온도는 약$262^{\circ}C$ 이었다. 히트파이프의 작동한계로서 드라이아웃(dry-out)은 충전률 372%의 경우에 열부하 950 W에서 발생하였으나, 그 이상의 충전률에서는 열부하 1060 W까지 작동한계 발생이 관찰되지 않았다. 실험 결과 본 연구에서의 히트파이프는 중온 태양열 축열조에 적용되어 개당 약 1 kW의 열부하를 이송하면서 축열물질 및 축방열 대상 유동매체와 열교환을 하는데 사용하는데 충분할 것이라 판단된다. -
국내의 많은 연구를 통해 신재생에너지의 사전 경제성 평가를 위한 모델들은 다수 개발된 바 있지만, 기본적인 연산 프로세스와 연산방식만 지원되고 있을 뿐, 연산결과에 크게 영향을 미치는 신재생에너지의 각 요소 데이터가 제공되지 못하고 있다. 이에 대하여 본 연구에서는 한국에너지기술연구원에서 개발된 신재생에너지 자원지도 데이터를 근간으로 하여 경제성 평가의 기본이 되는 정보를 데이터베이스로 구성함과 동시에 GIS(Geographical Information System)을 활용하여 해당 영역에서 직접 대상위치를 선정하고, 인자값의 설정에 따라 사전 적정성 평가를 지원하는 연산 프로세스를 개발하고자 하였다. 웹 도구를 활용하여 사용자의 접근을 용이하게 하며, 설비데이터의 입력이 가능하게 구성하여 지속적으로 업데이트가 가능한 시스템의 제작을 그 목표로 한다.
-
본 연구는
$CO_2$ 를 냉매로 하는 급탕용 히트펌프 성능특성을 평가하는 시험 평가법에 대하여 국내 실정에 맞는 시험평가법을 개발하기 위한 목적으로 기존$CO_2$ 급탕용 히트펌프의 평가방법을 분석하고자 한다. 현재$CO_2$ 급탕기 또는 급탕용 히트펌프 제품은 일본에서 2000년 초반부터 에코큐트라는 제품으로 일본 급탕용 난방기기로 판매되고 2009년을 기초로 누적판매 대수가 150만대에 이르고 있다. 국내에는 2008년 후반부터 공기열원 또는 폐열원 등을 이용한 급탕용 히트펌프 제품이 일부 수입되어 목욕탕, 찜질방과 같은 숙박업소용으로 판매되고 있는 추세이다. 국내에서는 급탕용 열펌프의 제품의 정의가 아직 정립되지 않고 이에 대한 시험평가방법이 전무한 실정이기 때문에 현재 일본의 가정용 열펌프 급탕기의 규격을 토대로 실제 급탕용 열펌프의 시험을 수행하여 급탕용 히트펌프의 급탕성능특성을 평가하는 방법을 개발하고자 한다. 시험시료는 일본에서 판매되고 있는 급탕용 히트펌프(D사) 제품을 이용하였으며, 현재 일본에서 사용하고 있는 JRA4050 규격에 의해 급탕성능평가를 진행하고 급탕성능평가 지표 등을 국내 유사조건과 급탕성능특성의 평가방법을 비교분석하였다. -
This paper describes development procedure of the four types of fuel cell's blowers: pressurized fuel blower, selective oxidation air blower, cathode air blower, and burner air blower. Diaphragm blowers having two heads are selected to maintain force balance when the rotating arms are moving by the driving motor. Dimensions of a diaphragm cavity is designed according to the optimal design procedure using numerical simulation and experimental measurement. Experimental apparatus is designed by considering the bower characteristics having low flow rate and high pressure. Test blower is operated by a diaphragm, which has suction and discharge port on the top of the blower. For analyzing the internal flow of the blower, three-dimensional Navier-Stokes analysis is introduced in the present study. Throughout the optimal design of the blowers, blower performance is enhanced by reducing the unbalance motion of the rotating arm and loss region in the diaphragm cavity.
-
Fuel cell systems are a completely different form of electricity source that has been used so far and is an aggregation of multiple technologies with multidisciplinary features that can be operated safely only when gas and electrical safety are being considered. Since fuel cells generate through electrochemical reactions there are difficulties in ensuring electricity safety, power quality assessment, effective control and reliability standards for system faults using conventional inspection techniques and even though they are necessary as a primary means for reduction of CO2 owing to the Climate Convention, electrical safety assessment and measures are required for the prevention of faults in residential facilities. Although small-scaled distributed power supplies can be utilized as important means of peak control and energy management measures, research is required for observing the effects on the system and the development of inspection technology to ensure stable operation, and the electrical safety of residential fuel cell systems need to be assessed and the problems derived for establishing electrical safety standards. From the year 2002, Japan has established laws on technical safety standards and development and rules on the product specifications and standards for the industrialization of hydrogen fuel cells. Also, a lot of effort have been made for the commercialization of fuel cells by building one-stop certification services. Internationally, the IEC TC 105 has established international standards based on fuel cells. In order to protect the national interest, the country should be able to respond accordingly meet global standards. In fact, in Korea, to comply with the international trend, Korea Energy Management Corporation is establishing a certified agenda for fuel cells and Korean Agency for Technology and Standards is enacting technical standards for fuel cells. The current terms of fuel cells are that research has been focused more on the quality and performance of manufactured products rather than stable power operation and maintenance over time. In this paper, by considering the household fuel cell as a power device, the safety standards of the fuel cell system for a reliable operation with the existing power system is being proposed.
-
공동주택에서 2025년 정부가 추진하고 있는 Zero Energy 건축물 구현과 친환경에 대한 탄소배출 저감 문제로 재생에너지 생산시스템의 추가 적용은 반드시 필요하다. 따라서 공동주택 적용 및 활용성을 높일 수 있는 BIPV시스템 개발을 통하여 설치면적 확보와 세대 활용성을 높일 수 있도록 하는 것이 필요하다. 특히 거실 창호의 경우 주방향이 남향, 남동 또는 남서향으로 배치되어 태양광을 적용하기에 적합한 특성을 가지고 있다. 그러나 창호는 건물외피의 역할과 재실자가 조망과 정보취득을 얻을 수 있는 중요한 통로가 되기 때문에 단열 문제나 시야 차폐의 문제는 발생하지는 않도록 하는 것이 필요하다. 본 연구에서는 a-si타입 모듈 2개를 10% 투과율로 Bsck Coating 색상을 달리한 모듈과 c-si BIPV 모듈을 커튼월 창호시스템으로 개발, 일반 2중 창호시스템과 비교 평가를 위해 실제 Test bed 건물에 시공하여 시환경 및 실내 창측면 온도변화 측정 분석을 진행하였다. 현재 국내외 출시되고 있는 a-si see through 모듈은 10~30%의 투과율로 창 마감재로 대체가 가능하나 건축 환경(시환경,열환경)에 대한 분석은 전무한 상태이다. 본 연구에서는 시환경과 창유리면의 열 부하, 자외선, 적외선 차폐 및 가시광선의 투과율에 대한 평가와 Back Coating에 따른 색온도 평가를 통해서 a-si BIPV의 공동주택 세대 발코니 창호 적합성에 대한 검토를 진행하였다. 연구결과는 아래와 같다.
${\bullet}$ 실내조도는 청천공 정오기준 가시성 확보 모듈의 경우 2,300 ~ 3,500lx를 나타내고 있어 대비 현상이나 창측의 급격한 조도 변화가 적은 시환경 구축이 가능${\bullet}$ 12시경 휘도는 창측면, 실내 벽체, 코너 바닥면을 대상으로 a-si BIPV 모듈을 적용한 경우 휘도비가 12:1로 KS나 IESNA의 광원과 근접면의 비 20:1 범위에 모두 존재, 적합한 것으로 분석되었으나 c-si의 경우는 그림자로 인한 대비 현상이 발생, 작업 시환경 문제 발생.${\bullet}$ 이중시스템 창호와 비교하여 단열 성능 떨어짐. 발전시간대 창유리 면 온도 상승 으로 하절기 냉방부하 증가.${\bullet}$ 자외선은 100% 가까이 차단, 적외선은 13~42%만 투과되고 가시광선은 13% 투과율을 나타내어 일반 창에 칼라 코팅을 적용하는 것과 유사한 경향을 나타냄. -
신 재생에너지 산업의 확대를 뒷받침하고 산업의 지속적인 성장을 달성하기 위해서는 지속적인 인력의 공급이 무엇보다 중요하다. 뿐만 아니라 신 재생에너지는 기존 에너지원과 다르게 자국 내에서 생산 및 소비가 함께 이루어진다. 따라서 신 재생에너지의 확대는 국가의 일자리 창출과 직접적으로 연관된다. 하지만 지금까지 국내에서는 신재생에너지 인력수요 전망을 위한 방법론 연구가 충분히 이루어 지고 있지 않은 실정이다. 이에 본 연구에서는 인력수요 전망을 위한 연구를 실시한 호주와 미국 사례를 고찰하여, 국내 신 재생에너지 인력수요 전망을 위한 고려요인 및 전망 방법론 연구를 실시하였다. 연구결과 미국은 기존화석에너지와의 인력수요 차이를 고찰하는데 초점을 맞추어 분석을 실시하였다. 또한 호주는 시나리오 기법을 통하여 미래 신재생에너지 보급상황에 따라 달라 질 수 있는 인력의 수요를 예측 하였다. 두 국가의 경우 신 재생에너지 부문의 인력수요가 급격하게 증가할 것으로 보고 있다. 호주의 경우 2008년 기준으로 10천명이던 신 재생에너지 인력수요가 2020년 24천명~30천명으로 증가할 것으로 예상(연평균 16.7% 증가)하고 있다. 미국에서는 2007년 500천명의 신 재생에너지 산업 인력이 재직 중이며, 신 재생에너지 확대와 함께 2030년에는 7,300천명의 인력수요가 있을 것으로 분석하고 있다. 신재생에너지 인력수요에 대한 연구를 실시한 사례를 살펴보면 국가는 목적에 부합하는 기준을 바탕으로 연구를 수행하여 있음을 알 수 있다. 따라서 우리나라도 향후 신재생에너지 인력 증가에 대비하여 관련 인력양성 정책을 올바르게 세우기 위해서는 관련 연구가 뒷받침 되어야 할 것으로 사료된다. 해외 사례 고찰 내용을 바탕으로 향후 국내 신 재생에너지 인력 수요 예측 시 고려해야 할 요인들을 다음과 같이 정리할 수 있다. 먼저 인력수요의 예측을 위해서는 현실적인 신 재생에너지 성장 시나리오의 설정이 요구된다. 미국의 사례와 같이 신 재생에너지와 재생에너지의 인력수요 차이를 비교하는 것도 신 재생에너지 인력수요를 정량화 하는데 큰 도움이 될 수 있다. 또한 인력의 범위를 직종별, 학력별로 구체화 하려는 노력이 필요할 것이다. 마지막으로 신재생 인력수요 전망을 바탕으로 효과적인 인력양성 프로그램을 구체화 해야 할 것이다.
-
Korea's RPS, which requires that power generation companies obtain a minimum percentage of their generation by using renewable energy, will take effect in 2012. Based on the first-year law enforcement, generation companies have to satisfy 2% of RPS compliance ratio in 2012. Then, the required RPS compliance ratio will increase up to 10% in 2022. Thus generation companies need to construct power plants that utilize various types of renewable energy sources such as PV and wind power. This work is aimed to analyze the cost of such a renewable power source in terms of capital cost, capacity factor, and fuel cost. We provide the analytical expectation on the renewable power generation cost of 2012 focusing on PV, onshore/offshore wind, fuel cell, and IGCC, which are focused by government policy.
-
청정 에너지원으로 높은 잠재력을 가지고 있는 가스하이드레이트는 상업적 기술개발이 미확보된 상태임에도, 우리나라에서 부존이 직접적으로 확인되었기 때문에 에너지원으로서 그 중요성이 부각되고 있다. 현재 전세계적으로 가스하이드레이트 개발 및 생산에 관한 연구가 활발히 진행되고 있으며 이에 대한 기초자료로서 가스하이드레이트가 함유된 퇴적층의 물성자료가 필요하다. 이에 따라 본 연구에서는 입도 분포별 총 5가지의 미고결 시료를 대상으로 투과도, p파속도, 전기비저항 측정을 수행하였다. 연구에 사용된 미고결 시료는 Hama#5(
$774{\mu}m$ ), #6($485{\mu}m$ ), #7($258{\mu}m$ ), #8($106{\mu}m$ ) 4가지와 Hama#6과 Hama#7을 1:1($371{\mu}m$ )로 혼합하여 사용하였다. 실험에 사용된 장비는 가스하이드레이트를 인공적으로 생성시키기 위해 퇴적층을 모사할 수 있는 고압셀과 자료획득장비, 유체 주입장비, 온도 유지장비이다. 또한 투과도 측정에는 차압계, 전기비저항 측정에 RLC meter, p파속도 측정에 음파 송수신장비를 사용하여 각각의 물성을 측정하였다. 실험과정을 단계별로 요약하면 먼저 시료를 고압셀에 충진한 뒤 주입된 물의 양으로부터 공극률을 측정하고, 절대 투수계수를 측정하였다. 그 후, 메탄가스를 주입하여 퇴적층 내 수포화도(water saturation)를 잔류상태(irreducible saturation)로 유지시키고 메탄가스를 추가적으로 주입하여 원하는 압력까지 가압한 뒤 온도를$1^{\circ}C$ 로 낮추었다. 가스하이드레이트의 생성은 급격한 압력강하로부터 알 수 있다. 최종적으로 가스하이트레이트가 함유된 퇴적층의 상대 투수계수를 측정하기 위해 메탄가스를 주입하였고 각각의 측정장비를 통해 전기비저항 및 p파 속도를 측정하였다.$V_g$ ,$V_h$ ,$V_w$ ,$V_ss$ 는 각각 가스의 부피, 하이드레이트의 부피, 물의 부피, 모래의 부피이다. 또한 수포화도,$S_w=\frac{V_w}{V_v}$ 이며 하이드레이트 포화도,$S_h=\frac{V_w}{V_v}$ , 가스 포화도,$S_g=\frac{V_g}{V_v}$ 로 정의된다. 본 실험의 결과 투과도는 가스의 부피비,$\frac{V_g}{V}=nS_g$ 에 민감한 반응을 보였으며, 비저항은 공극수의 부피비,$\frac{V_w}{V}=nS_w$ 에 민감한 반응을 보였다. 또한 p파 속도는 고체의 부피비,$\frac{V_s+V_h}{V}=n(1-S_h)$ 에 민감한 반응을 보였다. 이러한 실험의 결과는 가스하이드레이트 개발, 생산 연구에 있어 기초 물성자료로 활용되는데 도움을 줄 것이다. -
Large amounts of natural gas, mainly methane, in the form of hydrates are stored on continental margins. When gas hydrates are dissociated by any environmental trigger, generation of excess pore pressure due to released free gas may cause sediment deformation and weakening. Hence, damage on offshore structures or submarine landslide can occur by gas hydrate dissociation. Therefore, geotechnical stability of gas hydrate bearing sediments is in need to be securely assessed. However, geotechnical characteristics of gas hydrates bearing sediments including small-strain elastic moduli have been poorly identified. Synthesizing gas hydrate in natural seabed sediment specimen, which is mainly composed of silty-to-clayey soils, has been hardly attempted due to their low permeability. Moreover, it has been known that hydrate loci in pore spaces and heterogeneity of hydrate growth in specimen scale play a critical role in determining physical properties of hydrate bearing sediments. In the presented study, we synthesized gas hydrate containing sediments in an instrumented oedometric cell. Geotechnical and geophysical properties of gas hydrate bearing sediments including compressibility, small-strain elastic moduli, elastic wave, and electrical resistivity are determined by wave-based techniques during loading and unloading processes. Significant changes in volume change, elastic wave, and electrical resistivity have been observed during formation and dissociation of gas hydrate. Experimental results and analyses reveal that geotechnical properties of gas hydrates bearing sediments are highly governed by hydrate saturation, effective stress, void ratio, and soil types as well as morphological feature of hydrate formation in sediments.
-
용융탄산염 연료전지(MCFC)는
$650^{\circ}C$ 에서 작동하는 고온형 연료전지 시스템이다. 이 시스템은 천연가스 등을 개질하여 생산된 수소를 바로 전기로 생산할 수 있는 시스템으로 열효율이 높으며, 현재 대체 발전시스템으로 각광을 받고 있다. MCFC는 개질방식에 따라 내부개질 방식과 외부개질 방식이 있다. 내부개질 방식은 수소를 생산하는 개질기가 스택내부에 장착된 형식으로 천연가스를 스택내부에서 개질하여 바로 전기를 생산하는 방식이다. 이 내부개질반응에 사용되는 촉매로는 알루미나에 고함량 (약 50 wt.%)으로 담지된 니켈(Ni) 계열촉매이 주로 쓰이고 있다. 이 고함량으로 담지된 촉매는 대부분 높은 활성을 보인다. 비교적 낮은 온도 운전조건 (약$580{\sim}620^{\circ}C$ )을 가지는 MCFC 내부개질에 적용하기 위해서는 활성점인 니켈을 최대한 담지체에 고르게 분산 시켜야한다. 이를 위해서 MgO를 이용하여 촉매의 활성점을 높게 분산시키는 연구를 진행 하였다. 촉매를 제조하는 방법으로 요소(urea)를 이용한 균일용액침전법을 이용하였다. 니켈함량은 50 wt.%로 고정을 한 다음, MgO 양과$Al_2O_3$ 양을 각각 0 ~ 45 wt.%와 5 ~ 50 wt.%로 조절하면서 촉매를 제조하여 그 특성들을 분석하였다. 물성을 비교하기 위해서, X-선 회절분석 (XRD) 및 TPR, 물리화학흡착 실험을 하였다. 촉매의 활성을 살펴보기 위해서, fresh 상태 및 피독 상태에서 메탄수증기 개질활성 실험을 실시하였다. MgO 함량이 없거나 적은 촉매에서는 높은 BET surface area와 작은 NiO, metallic Ni 결정 크기가 나타났다. 반면 MgO 함량이 높은 촉매에서 낮은 BET surface area와 비교적 큰 NiO, metallic Ni 결정 크기가 나타났다. 또한 XRD 분석에서 MgO 함량이 증가할 수 록 MgO 결정 피크가 명확히 나타났으며,$MgAl_2O_4$ 피크는 나타나지 않았다. TPR 분석에서 촉매들의 환원 피크를 측정한 결과, 저함량의 MgO를 포함한 촉매는$700^{\circ}C$ 부근에 환원 피크가 관찰되었고 MgO가 고함량인 촉매는 환원 피크가$400^{\circ}C$ 부근에서 관찰되었다. 촉매의 초기 fresh 상태에서의 활성은 고함량 MgO를 포함한 Ni-90M10A 샘플을 제외하고 모든 촉매가 거의 비슷하게 나타났다. 그러나$K_2CO_3$ 피독 상태에서는 MgO 함량이 증가할 수 록 활성이 좋지 않았음을 알 수 있었다. 따라서 MgO가 소량 포함된 촉매의 경우 fresh 상태에서는 우수한 물성과 활성을 보이지만, 피독상태에서는 MgO가 포함되지 않은 Ni-$Al_2O_3$ 촉매가 우수한 활성을 보였다. -
In this work, magnesium (Mg) nanoparticles were plated onto the surfaces of multi-walled carbon nanotubes (MWNTs) in order to investigate the effects of their presence on the high pressure hydrogen storage behaviors of the resultant Mg/MWNTs. The structure of Mg/MWNTs was characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The pore structure and total pore volumes of Mg/MWNTs were analyzed by
$N_2$ /77 K adsorption isotherms. The hydrogen storage behaviors of the Mg/MWNTs were investigated by BEL-HP at 298K and 100 bar. From the results, it was found that Mg particles were homogeneously distributed on the MWNT surfaces. The hydrogen storage capacity increased in proportion to the Mg content. It can be concluded that Mg paricles play an important role in hydrogen storage characteristics due to the hydrogen spillover effect. -
리그노셀룰로오스 바이오매스를 원료로 하여 발효당을 생산하고자 할 때 최종적인 당수율은 적용하는 전처리 기술의 종류와 전처리 조건에 따라 크게 달라질 수 있다는 사실은 널리 알려져 있다. 또한 전처리물의 효소당화에서 셀룰로오스의 당전환율은 효소의 종류와 사용량에 의존적이므로 부족한 전처리 효과를 일부 보완하기도 한다. 본 연구에서는 바이오매스의 효소당화에 흔히 사용되고 있는 특정효소와 최근 공급되기 시작한 새로운 효소를 시료로 하여 해바라기 줄기의 열수전처리에 이은 효소당화에서 효소의 종류가 최종 당수율, 효소당화 시간 및 전처리효과에 미치는 영향을 측정하였다. 해바라기 줄기 분말을
$180^{\circ}C$ 에서 30분 동안 열수전처리하였을 때 헤미셀룰로오스의 수율이 최대가 되었으나 이 조건에서는 후속 효소당화에 의한 포도당 수율이 높지 않았다. Celluclast 1.5L 혹은 Celluclast conc BG는 전처리 물의 당화속도가 상대적으로 빠른 편이었고, 이 효소에 의한 당수율은 해바라기 줄기 셀룰로오스 함량의 80% 내외였으며, 바이오매스 1g당 효소첨가량이 3ml까지 증가함에 따라 당수율도 꾸준히 증가하는 경향을 보였다. 반면에 노보자임 스코리아로부터 분양받은 효소로서 NS22074와 NS50010의 혼합물은 Celluclast보다 약 10% 더 높은 당수율을 보여주었으나 당화는 상대적으로 느리게 진행되어 72시간 이상이 소요되었다. Endoxylanase 혹은 hemicellulase 등 다른 효소를 NS22074와 NS50010의 혼합물에 가하여도 당수율의 증대 효과는 미미하거나 거의 없었다. 시험에 사용한 효소제제에는 포도당, 소르비톨 등 여러 가지 당들이 보존제 혹은 안정화제로 함유되어 있는 것으로 나타나서 사용에 주의할 필요가 이었다. -
Anaerobic digestion(AD) has successfully been used for many applications that have conclusively demonstrated its ability to recycle biogenic wastes. AD has been successfully applied in industrial waste water treatment, stabilsation of sewage sludge, landfill management and recycling of biowaste and agricultural wastes as manure, energy crops. During AD, i.e. organic materials are decomposed by anaerobic forming bacteria and fina1ly converted to excellent fertilizer and biogas which is primarily composed of methane(CH4) and carbon dioxide(CO2) with smaller amounts of hydrogen sulfide(H2S) and ammonia(NH3), trace gases such as hydrogen(H2), nitrogen(N2), carbon monoxide(CO), oxygen(O2) and contain dust particles and siloxanes. The production and utilisation of biogas has several environmental advantages such as i)a renewable energy source, ii)reduction the release of methane to the atomsphere, iii)use as a substitute for fossil fuels. In utilisation of biogas, most of biogas produced from small scale plant e.g. farm-scale AD plant are used to provide as energy source for cooking and lighting, in most of the industrialised countries for energy recovery, environmental and safety reasons are used in combined heat and power(CHP) engines or as a supplement to natural. In particular, biogas to use as vehicle fuel or for grid injection there different biogas treatment steps are necessary, it is important to have a high energy content in biogas with biogas purification and upgrading. The energy content of biogas is in direct proportion to the methane content and by removing trace gases and carbon dioxide in the purification and upgrading process the energy content of biogas in increased. The process of purification and upgrading biogas generates new possibilities for its use since it can then replace natural gas, which is used extensively in many countries, However, those technologies add to the costs of biogas production. It is important to have an optimized purification and upgrading process in terms of low energy consumption and high efficiency giving high methane content in the upgraded gas. A number of technologies for purification and upgrading of biogas have been developed to use as a vehicle fuel or grid injection during the passed twenty years, and several technologies exist today and they are continually being improved. The biomethane which is produced from the purification and the upgrading process of biogas has gained increased attention due to rising oil and natural gas prices and increasing targets for renewable fuel quotes in many countries. New plants are continually being built and the number of biomethane plants was around 100 in 2009.
-
Ryou, Y.S.;Kang, Y.K.;Kim, Y.H.;Jang, J.K.;Kim, J.G.;Lee, H.M.;Kang, G.C.;Nah, K.D.;Huh, T.H. 190
In South Korea the gross generation and heated effluent of power generation plant was 259 TWh and 4.73 billion tons in 2008. And then the waste heat from power generation was 388 TWh. It shows that the efficiency of thermal power generation plant is about 40%. Therefore to reduce$CO_2$ emission from thermal power generation plant, the energy of this heated effluent must be reused to heat buildings or farm facilities. In South Korea horticultural facilities of about 25% are heated in winter season. Total area of greenhouses which are heated is about 13,000 ha. Total heat amount needed to warm greenhouse of 13,000 ha in winter season is only 3.4% of total waste heat from power generation plant. In this study a heat pump system was designed to reuse the waste heat from power generation. Especially new heat exchanger was developed to recover the thermal energy from waste water and this model considered anti-corrosion against sea water and low cost for economic feasibility. This heat recovery system was installed in mango growing greenhouse around thermal power generation plant in Seogwipo-city, Jeju Special Self-Governing Province. The result of preliminary test shows that the heating cost of about 90% is saved as compared to boiler using tax free light oil as a fuel. -
현재까지 대부분의 지열원 열펌프 시스템에 관한 연구는 열펌프 유닛과 지중열교환기에 대해 개별적으로 수행되었으며, 열펌프 유닛과 지중열교환기 설계 및 최적화의 공통변수인 지중순환수 유량에 따른 시스템 전체에 대한 연구성과는 매우 미미한 실정이다. 본 연구에서는 현재 국내에서 인증되어 보급되고 있는 물매물 지열원 열펌프 유닛의 성능 자료를 분석하고, 지중순환수 유량 변화에 따른 물대물 열펌프 유닛의 성능 실험 및 지중열교환기 형상에 관한 설계 및 분석을 수행하여 지열원 열펌프 시스템 최적화에 관한 기반 기술 확보하고자 하였다. 현재 국내의 물대물 지열원 열펌프 유닛의 냉방 및 난방 조건에서의 최소 인증 COP는 각각 4.1과 3.45이다. 다양한 용량 및 성능을 갖는 국내 인증 물대물 지열원 열펌프 유닛에 대한 정량적 성능 분석을 위하여 3.5kW(1RT) 용량당의 지중순환수 유량과 COP를 고찰하였다. 냉방운전시 3.5kW 단위 용량당 열펌프 유닛의 지중순환수 유량은 10.73에서 18.52LPM을 나타냈으며, 난방운전에는 10.41에서 18.16LPM을 나타냈다. 이때, 냉방 COP는 4.1에서 5.4의 값을 나타냈으며, 난방 COP는 각각 3.5에서 4.2를 나타냈다. 인증 열펌프 유닛에서 지중순환수 유량과 열펌프 유닛의 냉난방 성능은 일정한 경향성을 나타내지 않았다. 지중순환수 유량에 따른 지열원 열펌프 유닛과 시스템의 성능을 정량적으로 분석하고자 지중순환수 유량 변화에 따른 물대물 지열원 열펌프 유닛 성능 실험을 수행하고 이를 기반으로 지중열교환기를 설계 및 분석하였다. 냉난방 각 운전모드에서 ISO 13256-2 규격과 NRGT 101 규격을 기준으로 지중순환수와 부하측 유량 6LPM 에서 36LPM 사이에서 변화시키며 성능 실험을 수행하였다. 냉방 및 난방모드 모두 유량이 증가함에 따라 열펌프 유닛 COP가 증가하였으나, 유량 증가에 따른 열펌프 유닛 COP 증가율은 감소하였다. 지중순환수 유량이 18LPM 이상에서는 COP 상승폭은 미소하였다. 기존문헌의 부하 산정자료와 열펌프 유닛 실험 성능 데이터를 이용하여 지식경제부 고시 2009-332호에 준하여 수직밀폐형 지중열교환기를 설계하고 순환펌프 소요동력을 이용하여 시스템 COP를 분석하였다. 지중열교환기 설계 시 국내에서 가장 많이 사용되고 있는 상용지중열교환기 설계프로그램인 GLD 프로그램을 사용하였다. 지중순환수와 부하측 2차 유체 유량 증가 시에 열펌프 유닛 COP 증가율 대비 시스템 COP 증가율은 감소하였으며, 난방모드에서는 일정 유량 이상에서는 열펌프 유닛 COP는 증가하였으나, 시스템 COP는 감소하였다. 또한, 지중순환수 유량 증가에 따라 지중열교환기 길이가 증가하였으며, 냉난방시의 지중열교환기 길이차이가 증가하였다. 지열원 열펌프 시스템의 고효율화 및 시공비 절감을 통한 경제성 확보를 위해서는 지열원 열펌프 유닛 성능과 지중열교환기 형상 공통 변수인 지중순환수 유량을 함께 고려하여 시스템을 설계하여야한다.
-
Cooling and Heating system using Geothermal energy in the country has shown rapid development in the research and business field during about 10 years. However, like other renewable energy sources, high initial construction cost is acting as an obstacle to apply widely. Therefore Energy pile system(Heat Exchanger inserted inside the structure pile) that can save about 25 % initial construction cost has been studied in European countries and recently being studied in our country. Therefore, KPECO(Korea Electric Power Corporation) is also studying energy pile system to improve cooling & heating system in substation that install about 200 pile. KPECO is aimed to make energy pile design, construction and maintenance standards because substation has good applicability. In this study, we studied to make new grout material and design program to make optimized design & counstruction method of energy pile system. And planing to peform field test for energy pile system in a 154 kV substation to obtain long-term behavior and efficiency of the system.
-
ATES(Aquifer Thermal Energy Storage) 열펌프 시스템은 기존의 다양한 열원 적용 시스템 대비 효율이 우수한 것으로 알려져 유럽과 미국에서 건물 냉난방 시스템으로 적용되고 있다. 특히, ATES 시스템은 기존의 냉난방 시스템 대비 경제성이 우수한 것으로 알려져 있으나 국내에서는 이에 대한 연구 결과는 전무한 실정이다. 본 연구에서는 ATES 열펌프 시스템의 실증 성능 결과를 분석하였으며, LNG 보일러와 에어컨을 사용하는 기존의 냉난방 시스템을 비교시스템으로 ATES 열펌프 시스템의 경제성 평가를 수행하였다. ATES 시스템의 연간 실증 성능 실험결과 ATES 시스템은 외기온도와 무관하게 연중 안정적인 성능을 나타내었다. 경제성 평가시에 생애주기법(Life Cycle Cost)을 적용하여 ATES 열펌프 시스템의 설치 및 운전에 필요한 총 소요비용을 산정하고, 이 결과를 바탕으로 투자회수기간법을 통해 ATES 시스템의 투자회수 기간을 산정하였다. 생애주기법 적용 시에 현재가치법을 사용하였으며, 현재가치법은 수명주기에 발생하는 모든 투자비용과 절감액을 일정한 시점을 기준으로 등가환산하는 방법을 의미한다. 현재가치법에 사용되는 현재가치는 초기비용과 현재가치계수의 곱으로 나타나는데, 여기에서 현재가치계수는 임의의 이자율로 일정기간 동안 정기적인 할부금액이 적립될 때의 현재금액을 구하기 위해 사용하는 계수를 의미한다. 전기와 LNG는 각각 2009년 7월의 (주)한국전력공사와 (주)한국가스공사의 고시요금을 적용하였다. 본 시스템은 실증 설비용량인 20RT를 대상 건물로 가정하였고, 초기투자비는 크게 공사비와 냉난방 설비 구입비로 구성되어 있으며, 기본적인 물가지표는 (사)한국물가정보(KPI)의 고시 데이터를 참조하였다. 각 시스템의 초기투자비는 ATES 시스템이 비교대상 기존 냉난방 시스템 대비 5.7배 높게 나타났다. 일일 8시간 사용기준으로 계절별 전력요금을 고려한 연간운전 비용은 ATES 시스템이 기존 시스템 대비 냉난방 시에 각각 77%와 16%를 나타내어 운전비용이 연간 절감되었고, 난방 운전 시 절감 비율이 냉방시보다 크게 나타났다. 두 시스템에 대한 생애주기비용을 산정하기 위하여 에어컨과 보일러의 기존시스템과 ATES 시스템의 가용연수를 모두 20년으로 설정하였고, 유지보수 비용은 초기투자비용의 2%로 설정하고, 할인율은 은행 예금이자를 기준으로 5%로 설정하였다. 전기와 LNG의 요금 상승률은 (사)한국물가정보를 바탕으로 각각 2%와 8%로 가정하였다. 이러한 조건에서 생애주기법을 이용한 경제성평가는 ATES 시스템의 경우 생애운전비용이 초기투자비용보다 작게 나타났으며, 기존 냉난방 시스템은 생애운전비용이 초기투자비용에 비하여 높게 나타났다. 본 연구 대상 ATES 열펌프 시스템의 실증 성능 데이터와 기존 문헌으로부터 얻은 냉난방 시스템의 성능 결과를 이용하여 생애주기 비용을 적용한 결과 ATES 시스템의 기존 시스템 대비 투자회수 기간은 6.62년으로 나타났다. 특히, 본 연구에서는 ATES 시스템이 국내 최초로 적용됨에 따라 스크린 등의 부품을 다소 고가의 제품으로 시스템에 적용하였으므로 ATES 시스템의 신뢰성과 안정성이 확보되면 초기 투자비 감소가 가능할 것으로 예상되며, 기존 시스템 대비 투자회수 기간은 더욱 감소될 수 있을 것으로 예상된다.
-
Performance of the raw water-source heat pump system with a thermal storage tank has been analyzed in winter season. The raw water is transferred through the multi-regional water supply system from Han river. Raw water is large temperature difference resource compared with groundwater. Although the raw water temperature drops to
$0.6^{\circ}C$ due to the heavy snowfall and the severe cold in late January and early February, 2010, the system has been normally operated without any trouble this winter. The unit COP and system COP considered all pump power consumption were estimated based on the second-by-second data of the all sensors. The monthly averaged unit COP and system COP are 3.37 and 2.76 respectively with$1.4^{\circ}C$ of raw water in January, 3.55 and 2.89 with$1.6^{\circ}C$ raw water in February, 3.82 and 3.15 with$5.4^{\circ}C$ raw water in March. The performance of the system are increased with raw water temperature, and the COPs are higher than the water-to-air heat pump system using relatively high temperature raw water from Daecheong reservoir because the water-to-water system was operated on the full load condition and was stopped when the thermal storage tank was full of the high temperature water. -
본 논문에서 연구하고자 하는 팬은 대형 차량용 라디에이터 냉각팬으로써 수치해석을 통한 일반적인 팬의 성능 평가시 팬과 쉬라우드의 형상만을 이용하여 시뮬레이션 하지만 라디에이터를 거쳐 공기가 유입되는 실제 현상에 좀 더 가깝게 모사하고자 라디에이터의 압력 부하를 고려한 시뮬레이션을 수행하였고 기존 해석 결과와 비교하였다. 연구된 냉각팬은 쉬라우드의 전방에 라디에이터가 설치되며 라디에이터를 통하여 공기가 유입되기 때문에 라디에이터의 압력 부하에 따라 팬 성능에 영향을 준다. 라디에이터의 압력 부하 성능을 모사하기 위하여 쉬라우드 입구에 박스 형태로 라디에이터의 외부 크기를 모델링 한 후 수치해석 시 porous media model을 사용하여 풍속에 따른 압력 강하 곡선을 적용하였다. 수치해석에서 porous media model을 적용할 경우 실제적인 형상 모델링 없이도 실험으로부터 도출한 성능곡선을 조건으로 입력하여 실제 현상에 가까운 시뮬레이션을 할 수 있다. 그리고 팬 날개수 증가에 따른 해석을 수행하여, 날개수 변경에 따른 성능개선의 여지를 확인 하였다.
-
본 논문은 상용차용 전동 쿨링팬 모듈의 개발을 위한 5kW급 브러시리스 DC 전동기에 관하여 기술한다. 개발 대상전동기는 정격 3,000rpm의 회전속도를 목표로, 기존 팬 쉬라우드에 장착 가능한 박형으로 설계되며, 코깅토크 저감을 위한 회전자와 고정자 형상 최적화를 수행하여, 구동시 소음과 진동을 감소시키고자 하였다. 전동기를 제작하여 입출력 특성을 분석하고, 최종적으로 기 개발된 팬 블레이드와 결합하여, 쿨링팬 시스템의 유량 및 유압 특성시험을 진행하였다.
-
Plastic product is increasing by the growth of its demand and most of refused plastics are incinerated or reclaimed. However, the refused plastic is not easily decomposed and has the environmental problem with its various toxic gas in case of incineration. Therefore, many countries such as USA, Japan, Germany and other developed industrial countries as well as Korea are interested in studying the recyclable resource of refused plastic. The macromolecular waste pyrolysis has the advantage of collecting of raw materials in high price and can at least get fuel gas or oil with high heat capacity. It also discharges low waste gas and low toxic gas including SOx, NOx and HCl heavy metals. However, pyrolyzed oil includes enough excess unsaturated hydrocarbons to form tar, which can cause the nozzle of engines to plug when pyrolyzed oil is used as fuel. Activated carbon was proven to have prominent adsorption capability among the other adsorbents that were mainly composed of carbon. This study examined the possibility of application in activated charcoal of its solid formation by analysing the feature of pyrolysis which is one of the chemical recycling methods and getting chemical analysis of the product and activated energy. Analyze the element of the oil produced by pyrolysis using GC-MS. The experiment of tar adsorption using fly-ash showed that fly-ash improved the optical intensity of pyrolyzed oil and decreased oxygen compounds in the pyrolyzed oil.
-
풍력터빈에 적용되는 제어로직에 대한 검증을 실험실 기반에서 검증하기 위해서는 바람 및 터빈에 대한 적절한 모델링이 선행되어야 한다. 특히 피치 및 토크제어에 대한 특성을 검증하기 위해서는 블레이드 공력특성 및 터빈의 동특성에 대한 반영이 필연적이다. 본 논문에서는 풍력터빈 적용 제어로직 검증을 위하여 대상터빈에 대한 스케일링 결과, 바람을 모사하기 위한 구동장치 동작 및 터빈 모사장치에 대한 설계 결과에 대하여 소개하도록 한다.
-
The final site of offshore wind power plant should be decided by comprehensive examination of various conditions such as wind resource, sea depth, geology, grid connection, social circumstance and environmental issue. Wind condition is typically regarded as the most important factor because wind energy increases in proportion to wind velocity and it directly relates to the amount of power output, efficiency of power plant and profitability. Advanced countries in the offshore wind power sector such as Denmark, UK and Germany, they are analyzing wind resource accurately by installing the meteorological mast in the ocean in order to get the optimal type of wind turbine and maximum generation efficiency. Also, it is made much of designing offshore power plant on the basis of actual measurement by met-mast and those wind farms have a chance to get the loan with reduced interest rate in project financing. In Korea, the HEMOSU-1 is installed in the ocean around Wido island to analyze wind resource of test bed of 100MW offshore wind power on october last year. This paper deals with the design and construction procedure of the first met-mast in Korea and also shows the site characteristics of test bed. Therefore, this paper will give useful information to local governments and private business sector who are trying to construct offshore wind farm and it can also be a good reference for the following projects of meteorological mast in near future.
-
This study focus on the performance of blade with blunt airfoil which used at root region on Computational Fluid Dynamics(CFD). Based on the Phase VI had experiment by NREL, the experiment condition is also used for the performance of blade with the airfoil that trailing edge is changed. The thickness of airfoil trailing edge 1% and 5% is substituted for original airfoil. This study was progressing to calculate the pressure coefficient and torque from the effect on each airfoil according to difference of the thickness.
-
As rotor blade of a wind turbine becomes larger to satisfy the economic efficiency for offshore wind farm, the numerical analysis considering wind profile is getting emphasized. In this paper, the study for the power characteristic of a wind turbine is carried out using NREL phase VI wind turbine applied wind profile. The experimental data of NASA Ames wind tunnel for inflow velocity 7m/s is used and the numerical result is obtained by using CFD commercial solver(FLUENT).
-
본 논문에서는 소음을 저감하고 구조적 안전도를 향상시키기 위하여 10kW급 소형 복합재 풍력터빈 블레이드를 해석, 설계하였다. 풍력터빈 블레이드 설계의 기본 사항에 맞추어 블레이드의 스팬 길이는 약 4m, 중량은 30kg 내외가 되도록 설정하였다. 풍력발전기용 블레이드는 경량화가 중요하므로 유리섬유복합재 (glass fiber reinforce pastics), 탄소섬유복합재 (carbon fiber reinforced plastics)가 사용되었다. 본 설계에서는 Carbon prepreg (WSN3KY), Carbon UD(UIN150c), E-glass 등을 사용하였다. 상용 유한요소 프로그램인 NASTRAN을 이용해 Carbon prepreg (WSN3KY), Carbon UD (UIN150c)의 탄소섬유복합재만으로 구성된 블레이드 구조해석을 수행한 결과 중량 조건 및 강도의 안전도는 충족되었으나, 높은 가격을 감안하여 E-glass와 조합하여 블레이드를 재설계할 예정이다. 이번 설계는 소형 풍력발전용 블레이드 설계이므로 좌굴은 고려하지 않았으며, 향후 필요에 따라서 좌굴 및 피로해석도 수행하여 검증할 예정이다. 그리고 블레이드가 복합재로 구성되면 감쇠력이 감소할 가능성이 있다. 탄소섬유복합재로만 구성된 블레이드 구조해석에서도 최대 40cm의 변형이 예측되었으며, 감쇠값 저하 문제도 고려하여야 될 것 같아 BEMT (Blade Element Momentum Theory) 공력모델을 이용해 구조-유체 연성 결합 해석을 수행할 계획이다.
-
In this study, the effects of shear flows around a 2-dimensional airfoil, S809 on its aerodynamic characteristics were analyzed by CFD simulations. Various parameters including reference inflow velocity, shear rate, angle of attack, and cord length of the airfoil were examined. From the simulation results, several important characteristics were found. Shear rate in a flow makes some changes in the lift coefficient depending on its sign and magnitude but angle of attack does not have a distinguishable influence. Cord length and reference inflow also cause proportional and inversely proportional changes in lift coefficient, respectively. We adopted an analytic expression for the lift coefficient from the thin airfoil theory and proposed a modified form applicable to the traditional load analysis procedure based on the blade element momentum theory. Some preliminary results applied to an well known load simulation software, FAST, are presented.
-
In this paper, the purpose is a study on structural analysis for offshore wind turbine using commercial code. Because offshore wind turbine is subjected to great wind and wave force, it is necessary to analyse the dynamics and minimize the response of wind turbine. The offshore wind turbine tower is modelled as a single degree of freedom and multi degree of freedom structure. It is assumed that the blades, nacelle are composed of concentrated masses.
-
본 연구에서는 5MW급 수평축 풍력터빈 블레이드에 대해 국내 서남해안의 풍속특성을 고려한 최적설계를 수행 하였다. 최적설계를 수행하기 위해 블레이드 해석은 Blade Element and Momentum Theory를 이용 하였으며, 설계 시 적용된 기저형상은 NREL에서 제안한 5MW급 풍력터빈 블레이드을 선정하였다. 최적설계를 수행하기 전 설계에 사용된 설계변수들이 풍속에 대해 어떠한 경향을 가지고 있는지 알아보기 위해 Parametric Study를 수행 하였으며, 최적설계는 다목적 최적화 유전 알고리즘인 NSGA-II를 이용하여 평균풍속이 낮은 서남해안의 연간에너지 생산량과 설비이용률을 최대화하였다. 최적화 결과들로부터 설계 조건에 맞는 최적해를 도출 할 수 있었으며, 이를 통해 기저형상의 연간에너지 생산량 및 설비이용률을 보다 향상 시킬 수 있었다.
-
In this research, CFD calculation was implemented to analyze wind tunnel effect or rotor experiment in wind tunnel. One case included model wind turbine and all wind tunnel geometries. The other case include only rotor and nacelle system. Star-CCM+ was used for CFD analysis and rigid body motion around rotor area was applied to simulate rotating rotor. As for turbulence model, K-omega SST was used. The results were compared in 15m/s inflow condition. These results shows a good agreement with the measurement. Then, the result without wind tunnel was slightly different to the result with wind tunnel. Thus, in the case of Mexnex wind tunnel measurement, the wind tunnel don't affect the measurement result. Then, this wind tunnel and rotor size ratio can be reference for wind tunnel experiment of wind turbine rotor.
-
Although there are many activities on the construction of wind farm to produce amount of power from the wind, in practice power productions are not as much as its expected capabilities. This is because a lack of both the prediction of wind resources and the aerodynamic analysis on turbines with far wake effects. In far wake region, there are velocity deficits and increases of the turbulence intensity which lead to the power losses of the next turbine and the increases of dynamic loadings which could reduce system's life. The analysis on power losses and the increases of fatigue loadings in the wind farm is needed to prevent these unwanted consequences. Therefore, in this study velocity deficits have been predicted and aerodynamic analysis on turbines in the far wake is carried out from these velocity profiles. Ainslie's eddy viscosity wake model is adopted to determine a wake velocity and aerodynamic analysis on wind turbines is predicted by the numerical methods such as blade element momentum theory(BEMT) and vortex lattice method(VLM). The results show that velocity recovery is more rapid in the wake region with higher turbulence intensity. Since the velocity deficit is larger when the turbine has higher thrust coefficient, there is a huge aerodynamic power loss at the downstream turbine.
-
본 연구에서는 풍력 터빈 블레이드의 다분야 통합 최적 설계를 위하여, 진동하는 비정상 공력하중에 의한 작동 수명을 고려한 최적화 과정을 수행하였다. 최적화 대상으로는 NREL의 1.5MW 급 풍력터빈을 baseline 으로 하였고, NREL의 FAST 프로그램을 이용하여 발전기의 정격 출력 및 블레이드에 작용하는 비정상 공력 하중 특성을 분석하였다. 최적화 수행 시 블레이드 형상의 효율적인 구현을 위해 형상모델링 함수를 이용하여 코드 길이와 트위스트 분포를 모델링하였다. 그리고 상용 MDO Framework 인 Piano를 이용하여 블레이드 루트부의 비정상 공력하중 조건을 완화시키는 최적화 설계를 수행하였다. 정격출력을 유지하면서도 Out of Plain 방향의 하중 조건을 개선하여 보다 긴 작동 수명을 기대할 수 있는 블레이드 형상을 설계하였다.
-
This study is to develop a 1kW-class small wind turbine blade which will be applicable to relatively low speed regions. For this blade, a high efficiency wind turbine blade is designed and a light and low cost composite structure blade is adopted considering fatigue life. In this study, shape design of 1kW-class small wind turbine blade for hybrid power generation system is carried out by BEMT(blade element momentum theory). X-FOIL open software was used to acquire lift and drag coefficients of the 2D airfoils used in power prediction procedure. Moreover, pressure and velocity distributions are investigated according to TSR by CFD analysis.
-
풍력 터빈은 복잡한 바람 조건에 노출되어 운용 되는 시스템으로서 경제성과 신뢰성을 확보하기 위해서는 이러한 조건하에서 시스템에 작용하는 정확한 공력 하중 예측이 필요하다. 여러 조건 중에서도 요에러는 풍향이 수시로 바뀌기 때문에 피할 수 없는 비정상 유동 중에 하나이다. 본 연구에서는 이러한 요에러 발생시 공력 하중예측을 적절히 예측하기 위해서 와류 격자 기법을 기반으로 하는 비선형 와류 보정기법을 적용하였다. 비선형 와류 보정기법은 실속 이후의 공력 예측을 위해 기지의 공력 테이블을 이용하는 방법으로서 실속 이후의 공력 테이블 값의 양력과 와류 격자 기법에서의 양력 값이 일치하도록 순환(circulation)을 분포시키는 기법이다. 또한 요에러시에 발생할 수 있는 동적 실속을 계산하기 위해 Beddoes-Leishmen 동적 실속 모델을 비선형 와류 보정 기법에 적용하는 연구를 수행하였다. 요에러시 공력 하중 예측에 관한 수치해석 기법 연구의 적절성을 알아보기 위해 NREL-Phase VI Rotor 실험 결과와 비교 하였다. 그 결과 기존의 여타의 기법들과 비교하여 본 연구에서 제안한 기법의 적절성을 확인 할 수 있었다. 앞으로 본 연구를 바탕으로 다양한 비정상 공력 조건에 대한 풍력 블레이드의 공력 하중 해석에 대해 수행할 계획이다.
-
The spanwise aerodynamic loads of the wind turbine blade are investigated numerically. The blade shape such as twist and chord length along the blade span is obtained from the procedure of aerodynamically optimal design. The rated tip speed ratio and the rated wind velocity are set to 7 and 12m/s respectively. The BEM method is applied to obtain both the aerodynamic performance of the wind turbine (Fig.1) and the spanwise aerodynamic loads along the blade span including Prandtl's tip loss factor. The maximum running power coefficient is occurred around 90% radial position from hub (Fig.2). The distributed aerodynamic loads along the blade span can be used for structure analysis.
-
The wind can be stronger and steadier further from shore, but water depth is also deeper. Then bottom-mounted towers are not feasible, and floating turbines are more competitive. There are additional motions in an offshore floating wind turbine, which results in a more complex aerodynamics operating environment for the turbine rotor. Many aerodynamic analysis methods rely on blade element momentum theory to investigate aerodynamic load, which are not valid in vortex ring state that occurs in floating wind turbine operations. So, vortex lattice method, which is more physical, was used in this analysis. Floating platform's prescribed positions were calculated in the time domain by using floating system RAO and waves that are simulated using JONSWAP spectrum. The average value of in-plane aerodynamic force increase, but the value of out-of-plane force decrease. The maximum variation aerodynamic force abruptly increases in severe sea state. Especially, as the pitch motion of the barge platform is large, this motion should be avoided to decrease the aerodynamic load variation.
-
This study predicted broadband noise from a generic 2.5MW wind turbine blade in the time domain. The rotor blade was modeled as thin rectangular flat plates. A simplified analytic model proposed by Amiet was used to model the unsteady surface pressure distribution. The acoustic pressure was calculated by using the loading term of Formulation 1A proposed by Farassat. The validation was also performed by comparing with an experiment of Brooks, Pope, and Marcolini. By using these numerical methods, the broadband noise signal of the wind turbine was successfully predicted in this study.
-
본 연구에서는 제주 삼달 지역의 Hub 높이에서 측정된 실측 자료와 기상청에서 측정된 AWS 자료 1년(2010년)치를 토대로 Wind-Pro에 적용하여 풍황자원 분석을 하였다. 허브의 실측높이인 삼달지역 관측자료(100m)와 허브 보정값인 기상청 AWS 자료(15m)를 통해 각각의 연간발전량과 단지 효율을 측정하여 비교 분석하였고 실측높이와 보정치를 이용한 값을 적용하여 발전량 및 효율을 산출 비교하고 이를 통해 그 차이점을 분석하고자 한다. 이는 단지분석 시에 발생될 보정값의 불확도를 판단하는데 그 의의가 있다.
-
The objective of this study is to investigate the aerodynamic characteristics of a small vertical axis wind turbine with dual blade type. The Wind turbine with dual blade has various angle of attack. so this turbine improve starting characteristics. The various arrangement of the vertical axis wind turbine with dual blade is designed. Among them, it shows superior quality that is arranged in three rows. Among arrangement in three rows, we use general computational fluid dynamics program CFX to find out the optimal arrangement. By comparing the predicted results of the aerodynamic characteristics of the different arrangement of the blades, an appropriate arrangement of the blade is suggested to design the small wind turbine blade.
-
Small horizontal axis wind turbines (HAWTs) can be used to produce power in areas where the wind conditions are not favorable or optimal for large HAWTs. A newly designed airfoil for use in small HAWTs was analyzed in CFD to predict the aerodynamic performance at various Reynolds numbers over a various angles of attack. The coefficient of lift and drag, CL and CD, and the pressure distribution over the airfoil was obtained. It was found that the airfoil could achieve very good aerodynamic characteristics. The results of the numerical analysis will be compared against experimental data for validation purposes.
-
해상용(offshore) 부이(bouy)는 선박의 항로를 지시하거나 암초, 침몰선 등 항해상의 위험물을 알리기 위해 사용 되며, 야간을 위해 등화장치를 설치한 것을 등부표라 한다. 등부표는 야간 점등을 위해 자체 전력 생산시스템을 갖추고 있으나, 기존의 태양광을 이용한 전력 시스템은 해상 환경에 따른 제약이 많아 안정적인 운영이 어려우므로 풍력 발전기(wind turbine)를 이용한 하이브리드 전력 생산시스템으로의 전환이 필요한 실정이다. 선행 연구는 수직축(vertical axis) 양력(lift) 및 항력(drag) 조합형 해상용 풍력발전기 개발에 대하여 수행하였으나, 본 논문에서는 풍력발전기의 효율 증대를 위해 날개 길이 및 후면부 절개 비율에 따른 수직축 풍력발전기 특성에 대하여 연구하였다. 풍력발전기의 설치조건은 선행연구와 동일하게 등명구 교체 작업을 원활하게 하기 위하여 설치 공간을
$1m{\times}1m$ 로 제한하였으며, 등부표의 구조를 고려하여 최상단에 지지 프레임을 별도로 구성 하였다. 풍력발전기의 블레이드는 0.6mm의 알루미늄 박판을 절곡하여 NACA 4418의 외형을 가지도록 제작하였고, 블레이드 설계 시 에어포일의 후면부를 절개하여 양력과 항력을 효과적으로 이용하며 저속과 고속에서 높은 효율을 가지도록 설계하였다. 또한 블레이드 날개 길이와 후면부 절개 비율에 따른 풍력발전기 특성을 실험을 통해 비교하여 기준 해상 풍속에서 블레이드 설계 최적화를 수행하였으며 비교 모델 대비 약32% 발전량이 증가한 설계변수 조합을 구하였다. -
Knowledge of the solar radiation components and classified wavelength are essential for modeling many solar energy systems. This is particularly the case for applications that concentrate the incident energy to attain high photo-dynamic efficiency achievable only at the higher intensities. In order to estimate the performance of concentrating solar systems, it is necessary to know the intensity of the beam radiation, as only this components can be concentrated, and The new solar system can generate electricity from ultraviolet and infrared light as well as visible light. The Korea Institute of Energy Research(KIER) has began collecting solar radiation components data since January, 1988, and solar radiation classified wavelength data since November, 2008. KIER's solar radiation components and classified wavelength data will be extensively used by concentrating solar system users or designers as well as by research institutes.
-
It is necessary to estimate empirical constants in order to predict the monthly mean daily global radiation on a horizontal surface in the developing areas for alternative energy. Therefore many different equations have proposed to evaluate them for certain areas. In this work a new correlation has been made to predict the solar radiation for any areas over Korea by calculating the regression models taking into account latitude, percentage of possible sunshine, and cloud cover. From the results, the single linear equation proposed by using percentage of possible sunshine method shows reliable results for estimating the global radiation with average annual deviation of -3.1 to +0.6 % from measured values.
-
석탄가스화 복합발전(IGCC) 시스템은 고온 고압으로 운전되는 가스화기에서 미분탄을 산소와 함께 가스화하여 주로 CO 및
$H_2$ 를 생성하고 이때 발생되는 먼지 및 황성분은 각각 집진기 및 탈황장치에서 제거되며, 석탄 회분은 고온에서 용융되어 슬래그의 형태로 배출되는 방식을 사용하고 있다. 본 연구에서는 석탄가스화 복합발전시스템 설계에 필요한 기본자료를 파악하기 위해서, 고온 고압의 운전조건에서 1일 3톤의 석탄을 처리할 수 있는 Bench Scale급 석탄가스화기를 이용하여 가스화에 사용된 원탄 및 가스화기 설비의 각 지점에서 샘플링한 고체 시료를 중심으로 열화학적 특성을 살펴보았다. 가스화 실험은 아역청탄 계열의 ABK 석탄을 대상으로 가스화기 내부의 온도와 압력을$1400{\sim}1450^{\circ}C$ ,$7.5{\sim}7.6Kg/cm^2$ 로 유지시키면서 실시하였다. 실험에 사용된 석탄 시료의 기본적인 물성치를 조사하기 위하여 표준방법에 따라 석탄의 공업분석, 원소분석, 발열량분석 등을 실시하였다. 석탄가스화기에서 배출된 슬래그와 대상 석탄 회분의 특성을 파악하기 위해서 XRF를 이용한 회분의 성분분석, Heating Microscope를 이용한 회분의 용융점 분석, XRD를 이용한 회분과 슬래그내의 화합물의 형태 및 결정구조 파악, SEM을 이용한 슬래그의 형상 등을 분석하였다. 또한 석탄가스화기 시스템을 구성하는 각 설비의 특성을 파악하기 위해서 관련 설비의 특정 지점에서 채취한 시료의 입도분석, 원소분석, 촤 회분 무게비, 슬래그중의 잔존탄소함량, 슬래그와 슬래그로부터 제조된 용출수내의 중금속 함량분석 등을 실시하였다. -
Baek, Jeom-In;Lee, Kisun;Wi, Yong-Ho;Choi, Dong Hyeok;Eom, Tae-Hyoung;Lee, Joong Beom;Ryu, Chong Kul 73.2
석탄 합성가스 중에는$H_2S$ , HCl,$NH_3$ 와 같은 불순물이 포함되어 있다. 이러한 가스들은 오염가스 배출과 관련한 환경기준 준수와 터빈과 같은 설비의 보호를 위해 제거되어야 한다. 석탄 합성가스 중 HCl 농도는 탄종에 따라 다르기는 하지만 많게는 1000 ppmv 수준까지 존재한다. 합성가스를 이용하여 발전을 하는 경우 가스터빈 보호를 위해 HCl은 <3 ppmv 이하로 정제되어야 하고, 합성가스를 연료전지에 사용하고자 하는 경우에는 HCl을 <0.5 ppmv 수준까지, 화학원료로 사용하고자 하는 경우에는 <10 ppbv 수준까지 정제하여야 한다. 또한 HCl은 고온 탈황공정에 사용되는 흡수제의 활성에도 장기적으로 부정적인 영향을 주기 때문에 고온에서 HCl을 정제할 수 있는 흡수제가 필요하다. 본 연구에서는 알칼리금속을 활성물질로 사용하여 분무건조법으로 제조한 HCl 흡수제에 대해 물성 및 HCl과의 반응성을 살펴보았다.$300-500^{\circ}C$ 영역에서 K-계 및 Na-계 흡수제에 대해 고정층반응기에서 HCl 가스를 함유한 모사 합성가스를 이용하여 상압 조건에서 Cl 흡수능을 측정한 결과 15wt% 이상의 흡수능을 나타내었으며 반응온도가 높을수록 흡수능이 증가함을 알 수 있었다. XRD 분석을 통하여 Cl은 K 및 Na와 반응하여 KCl과 NaCl을 형성하면서 흡수됨을 알 수 있었다. 20 bar 조건에서 실험한 결과에서도 동일한 경향의 반응성을 나타내었으며 반응온도가 낮을수록 흡수능은 감소하지만 Cl을 더 낮은 농도로 정제할 수 있었다. 본 실험에 사용된 Na 및 K계 흡수제는 모두 연소 후 배가스 중$CO_2$ 를 제거하기 위한 흡수제로 사용되는 고체 흡수제이다. 석탄화력발전소 배가스에 연계되어$CO_2$ 회수실험에 사용되었던 사용 후$CO_2$ 흡수제에 대해 HCl 흡수 실험을 수행한 결과에서도 우수한 HCl 제거 성능을 보여 주었다. 이로부터, 폐$CO_2$ 흡수제의 HCl 흡수제로서의 활용가능성을 확인 하였다. -
탄소나노튜브는 높은 전기 전도성과 열 전도성을 가지며, 이러한 특성 때문에 21세기를 주도해 나갈 수 있는 차세대 첨단 소재로서 각광을 받고 있다. 또한 최근에는 나노공학기술의 발달로 인하여 획기적으로 높은 열전도도를 나타내는 다중벽 탄소나노튜브(Multi-walled Carbon Nanotubes, MWCNTs)의 대량 생산이 가능하게 되면서 다중벽 탄소나노튜브의 높은 열전도도 특성을 이용하여 탄소나노튜브를 기본 유체 및 기능성 유체에 안정하게 분산 시킨 후 이를 이용하고자 하는 연구가 활발히 진행되고 있으며, 탄소나노튜브를 유체에 안정하게 분산시키기 위한 방법으로는 기계적 분산법, 물리적 흡착에 의한 분산법, 화학적 개질에 의한 분산법이 있다. 따라서 본 연구에서는 이들 분산 방법과 탄소나노튜브 입자의 물성치에 따른 나노유체의 특성을 알아보기 위하여 나노유체의 열전도도와 점도 특성을 비교 분석하였다. 모든 물성치는 같지만 탄소나노튜브의 길이만 다른 두 종류의 다중벽 탄소나노튜브에 각각 계면 활성제(Sodium Dodecyl Sulfate, SDS) 100 wt%와 고분자 화합물(Polyvinyl Pyrrolidone, PVP) 300 wt%를 첨가하여 나노유체를 제조하였으며, 산화처리 된 다중벽 탄소나노튜브(Oxidized Multi-Walled Carbon Nanotubes, OMWCNTs)를 증류수에 초음파 분산하여 산화나노유체를 제조하였다. 나노유체의 열전도도는 전기 전도성 유체의 비정상 열선법(Transient Hot-wire Method)을 이용하여 측정하였고, 나노유체의 점도는 회전형 디지털 점도계를 이용하여 측정하였다. 실험 결과, 상온에서 동일 혼합비의 나노유체를 비교했을 때, 산화나노유체가 SDS 100 wt%, PVP 300 wt%를 혼합한 다른 나노유체보다 높은 열전도도 특성을 보였으며 점도 특성 또한 가장 낮은 것으로 측정되었다. 특히 상온에서 0.1vol%의 산화 CM-100 나노유체는 증류수보다 열전도도가 8.34%가 증가하였고,
$10^{\circ}C$ 의 저온에서는 상온에서 증류수와 비교하여 측정된 열전도도 값보다 0.36%가 감소한 7.98%가 증가함을 보였다. 본 연구를 통하여 얻어진 결과는 높은 열전도도를 필요로 하는 열교환기의 작동유체나 기타 활용 분야에 대한 기초 자료로써 유용한 정보를 제공할 것이라 판단된다. -
A simulation study on synthesis gas process in GTL process was carried out in order to find optimum operation conditions for GTL (gas-to-liquid) pilot plant design. Optimum operating conditions for synthesis gas process were determined by changing reaction variables such as feed temperature and pressure. During the simulation, overall synthesis process was assumed to proceed under steady-state conditions. It was also assumed that physical properties of reaction medium were governed by RKS (Redlich-Kwong-Soave) equation. The effect of temperature and pressure on synthesis gas process
$H_2$ /CO ratio were mainly examined. Simulation results were also compared to experimental results to confirm the reliability of simulation model. Simulation results were reasonably well matched with experimental results. -
화석연료의 고갈과 온실가스 배출의 증가로 지속 가능한 친환경 에너지 생산이 요구되는 가운데, 태양광 발전은 이러한 조건을 만족시키는 에너지 생산 방안으로 주목받고 있다. 태양광 발전은 태양 직사광을 이용한 발전 방법 때문에 실외에 설치되어야 하며 이에 따라 외부의 충격이나 오염물질로부터 태양전지 패널을 보호하기 위한 보호층이 필수적이다. 그러나 보호층에 의한 입사광의 반사 및 먼지나 황사에 의한 보호층의 오염 등은 태양전지의 발전 효율을 감소시키는 요인으로 작용하여 이에 대한 대응이 필요하다. 본 연구에서는 PET 필름에 나노 임프린트 리소그래피 및 핫 엠보싱 공정을 이용하여 moth-eye 반사방지 패턴을 형성함으로써 보호층에서의 입사광 반사를 억제하였다. 또한, 이러한 반사방지 패턴에 초소수성 자기조립단분자막을 코팅하여 표면 에너지를 낮춤으로써 먼지 및 황사에 의해 오염되었을 경우에도 빗물에 의해 오염 물질이 쉽게 씻겨 내릴 수 있는 자정기능을 부여하였다. 이러한 반사방지를 통한 입사광 투과량의 향상 및 초소수성 표면에 의한 자정작용에 의하여 태양전지의 발전 효율이 증가되었다.
-
국내 유인도서의 상당수는 전력의 대부분을 디젤발전으로 생산한다. 향후 발전설비의 교체 혹은 증설이 있을 경우 신재생에너지원 설비의 보급 여지가 있다. 이에 본 연구는 울릉도에 화력발전 설비만을 증설했을 경우와 이를 신재생에너지복합시스템 설비로 대체했을 때의 경제적 타당성을 비교분석한다. 우리는 복합발전 시스템을 풍력터빈, PV, 소수력발전 등의 신재생에너지 설비, Batteries, Converter와 같은 보조전원, 저장 및 back up을 위한 flywheel과 Diesel generator등으로 구성했다. 분석에 사용한 HOMER(Hybrid Optimization for Energy Renewable)는 신재생에너지복합 발전시스템 분석에 사용되며 결과를 NPC(Net Present Cost)의 오름차순으로 제시하여 발전설비구성의 조합들 중 최적의 시나리오를 보여준다. 분석결과 울릉도의 경우 신재생에너지복합 발전의 보급이 잠재적으로 가능할 것으로 보인다. 또한 계통운영의 기술적인 측면을 감안할 경우 정밀한 분석이 가능할 것이다. 따라서 본 연구는 계통운영과 경제성분석 연구의 연계를 위한 사전연구로써 그 의미를 갖는다.
-
With the growing penetration of distributed generation including from renewable sources, smart grid power system is needed to address the reliability problem. One important feature of smart grid is demand response. In order to design a demand response program, it is indispensable to understand how consumer reacts upon the change of electricity price. In this paper, we construct an econometrics model to estimate the hourly price elasticity of demand. This panel model utilizes the hourly load data obtained from KEPCO for the period from year 2005 to 2009. The hourly price elasticity of demand is found to be statistically significant for all the sample under investigation. The samples used for this analysis is from the past historical data under the price structure of three different time zones for each season. The result of the analysis of this time of use pricing structure would allow the policy maker design an appropriate incentive program. This study is important in the sense that it provides a basic research information for designing future demand response programs.
-
Kim, Hak-Joo;Jung, Heon;Lee, Ho-Tae;Yang, Jung-Il;Chun, Dong-Hyun;Yang, Jung-Hoon;Park, Ji-Chan;Kim, Byung-Kwon 76.2
석탄으로부터 합성석유를 생산하는 상용기술을 도입하여 건설하고 이와 더불어 원천기술 개발을 위한 국산화 기술 개발을 병행하여 향후 고유가 시대를 대비한 국가 에너지 안보 확립과 국내 기술 개발의 가속화를 추구해야 할 필요성이 대두되고 있다. 본 타당성 조사는 3종류의 석탄(호주 Wyong탄, 인도네시아 NTC탄, 인도네시아 KBB탄)으로부터 가스화에 의하여 합성석유스를 생산하는 공정에 대한 타당성 조사(Feasibility Study, FS)를 Class 5(하한 -50~-20%, 상한 30~100%)의 정확도로 수행하는 것을 내용으로 하고 있다. 플랜트의 규모는 합성석유 기준으로 20,000배럴/일이다. 플랜트의 건설을 위해서 광양제철소 슬래그처리장 내 12만평 부지에 조성 중인 포스코 SNG 생산공장 부지의 일부를 사용하는 것을 기준으로 하였다. 일반적으로 석탄의 종류에 따라서 가스화기의 종류 및 성능이 결정된다. 본 타당성 조사 연구에서 선정된 3종류의 석탄의 조성, 발열량, 회분 함량 등의 특성을 고려하여 각각의 석탄에 적합한 현존하는 상용급 가스화기를 선정하였다. 해당 석탄이 가스화기 종류에 따라 적절한 전처리 과정(건조, 분쇄, 슬러리화)을 거친 후 가스화기에 공급되는 것을 가정하여 석탄의 원소분석 조성, 발열량, 회분함량, 회분조성, 회 용융점 등의 변수에 따라서 각각 해당 가스화기에서 가스화되었을 때의 생성되는 합성가스의 조건을 시뮬레이션을 통하여 얻었다. 가스화기 시뮬레이션 결과를 토대로 합성석유 및 합성천연가스 생산을 위한 공정의 물질수지식 및 에너지수지식이 계산되었으며 이로부터 각 공정에서 발생되는 부생성물과 폐기물에 대한 양이 결정되고 이를 처리하는 방안 등도 제시되었다. 실증시설은 20,000배럴/일 규모의 CTL 및 전기 병산 시설이 적합하다. 더 큰 규모 공장은 투자비가 너무 커서 유가 또는 석탄가 변동에 따라 사업의 수익성이 크게 변하여 위험도가 큰 단점이 있기 때문이다. CTL 공장에 전기 병산이 추천되는 이유는 산소생산공장(APU), 압축 등 석탄전환공장에는 자체적인 전기수요가 막대하여 따로 스팀터빈용 발전소를 운영하므로 이를 효율적으로 대체하고자 하기 때문이다. 즉, 석탄가스화에 의해 기름을 최대한 만들고 미반응가스는 가스터빈 및 스팀터빈의 복합발전에 의해 고효율로 전기를 생산하면 최소의 비용으로 최대한 전기를 생산하여 자체소비 전력을 충당하고 남는 전기는 판매하여 수익률을 높일 수 있다. -
Yang, Jung Hoon;Hur, Young Gul;Yang, Jung-Il;Kim, Hak-Joo;Chun, Dong Hyun;Kim, Byung Kwon;Lee, Ho-Tae;Jung, Heon 77.1
슬러리 기포탑 반응기는 열 및 물질 전달의 용이성, 낮은 운전비용 및 장치의 간단성의 장점을 가지고 있어서 Fischer-Tropsch 반응, bio-reaction 등에 많이 응용되고 있다. 특히, 반응물은 기체 상태로 반응기에 투입이 되는데, 이 기포입자의 상승하는 힘을 바탕으로 기상/액상/고상이 균일하게 혼합되게 된다. 많은 연구자들이 이러한 기포탑 반응기의 성능을 개선하고자, 다양한 반응기 디자인에 대하여 보고하고 있다. 특히 반응기 내부에 tray를 설치함으로써, 기포 포집율을 증진시기고 액상의 역류를 최소화시키는 연구가 활발히 진행되고 있다. 본 연구에서는, 다양한 기공크기를 갖는 tray를 활용함으로써 높이에 따른 기포 포집율의 변화 및 반응기 내에 기포 입자의 거동 특성에 대하여 살펴보았다. -
고온고압에서 운전되는 분류층 석탄가스화기에서 석탄의 회성분을 용융슬래그로 원활하게 배출하는 것은 석탄가스화기의 안정적인 운전을 위하여 매우 중요하다. 본 연구에서는 분류층 석탄가스화기에서 원활한 슬래그의 배출조건을 파악하기 위해서 여러 슬래그 점도예측 모델들을 사용하여 가스화기의 운전온도 변화에 따른 슬래그의 점도변화를 해석하여 점도해석모델들의 적용성을 비교분석하였다. 본 연구에서 선정한 가스화기 설계탄의 회 성분을 토대로 슬래그의 점도를 계산한 결과 점도해석 모델별로 온도에 대한 점도 값이 매우 상이하게 예측되었다. 또한 설계탄에 대한 점도예측 모델들을 적용한 계산결과로부터 슬래그의 점도가 80 poise가 되는 온도인
$T_{80}$ 이 매우 높은 값으로 예측되었다. 따라서 가스화기의 운전온도에서 용융 슬래그를 원활하게 배출하기 위해서 설계탄에 Flux를 첨가하여 슬래그의 점도를 낮추어 줄 필요가 있음을 알았다. 기존의 점도예측 모델들 중에 점도 예측 값이 중간치 정도의 경향을 보이는 Hoy가 개발한 모델을 기준으로 가스화기의 적정 운전온도에서 Flux로 첨가할 석회석 양을 산출하였다. 본 슬래그 점도모델들의 적용 결과로부터 실제 가스화기의 운전이나 설계에 슬래그의 특성을 파악하여 운전조건 도출이나 해석에 활용하기 위해서는 운전예정인 탄종에 대한 점도측정 실험을 병행하여 적정한 점도 예측모델을 선정하는 것이 중요함을 알 수 있었다. -
Ra, Howon;Choi, Young Chan;Lee, Dongwook;Hong, Jaechang;Bae, Jongsoo;Park, Sejun;Lee, Youngju 78.1
분포지역과 매장량이 한정되어 있는 석유에 비하여 석탄은 가채년수가 길고 세계 전역에 널리 분포되어 있으므로 향후 안정적인 에너지 공급으로 각광받고 있다. 석탄을 이용하여 CWM을 제조하는 기술은 석유에 비하여 저장, 수송, 분진 비산등의 문제점을 개선하여 위하여 1980년대부터 석탄 물 혼 합연료(Coal-Water Mixture)의 기술개발을 위한 연구가 진행되었다. 이는 미분탄(유연탄)에 30%정도의 물과 약간의 첨가제를 혼합하여 유체화하여 수송성은 액체연료와 같고 연소성은 석탄의 성상을 갖는 특징을 가지게 된다. 본 연구에서는 당센터에서 보유하고 있는 습식 분류층 가스화장치에 적용하기 위한 CWM(Coal Water Mixture)제조 특성을 연구하였다. 습식 석탄 가스화기에 사용되는 CWM은 미분되어진 석탄과 물, 첨가제를 일정비율로 혼합하여 사용하게 된다. 이때 공급되어지는 미분의 입도와 분쇄 형태에 따른 입자 형태, 입자의 분포에 따라서 CWM의 특성이 각각 다르게 나타나게 된다. 이때 만들어진 CWM의 농도와 점도 특성에 따라서 버너의 성능 및 가스화기 운전 조건등에 많은 영향을 미치게 된다. 습식 석탄 가스화에 적용된 예정인 대상탄을 대상으로 하여 석탄분쇄 형태에 따른 CWM의 제조 특성을 실험하였다. -
To achieve the required higher efficiency and lower emission performance, Korea's 300 MW IGCC RDD&D (Research Development, Demonstration and Dissemination) project was launched in December 2006 under the leadership of the Korea Electric Power Corporation (KEPCO), with the support of the Korea Ministry of Knowledge Economy. Our research group, KEPCO Research Institute had set-up the a coal gasifier for the pilot test and conducted many experiments for parametric study in this project. Our group focused visualization of pulverized coal injection pattern in the gasifier. Through this study we found that two types of coal burners having different oxygen supply angles can be a source changing gasification condition like temperature.
-
인쇄전자 기술은 기존의 다양한 인쇄 공정에 전자 재료를 적용하여 전자소자 및 전자소자에 적용 가능한 제품들을 생산하는 기술이다. 인쇄 공정은 크게 접촉식과 비접촉식으로 구분할 수 있는데 비접촉식 인쇄 방식의 대표적인 예가 잉크젯과 스프레이 방식을 이용한 인쇄라고 할 수 있다. ESD는 정전기력을 이용한 스프레이 방식의 인쇄 공정으로써 기존의 정전기력만을 이용한 인쇄 방식과는 달리 정전기력과 공압을 동시에 적용하여 상대적으로 빠른 시간 내에 나노 박막의 코팅과 패터닝이 가능한 공정이다. 일반적으로 터치 패널에 사용되는 ITO의 경우는 증착 방식에 의존하고 있어 공정 시간이 길고 생산 단가도 비싸다는 단점이 있다. ESD 코팅의 경우는 기존의 증착 방식이 아닌 직접 인쇄 방식으로 공정 시간과 비용을 절감할 수 있는 장점이 있다. 투명 전도막 형성에 사용되는 전도성 고분자의 경우 ITO를 대체할 수 있을 만큼의 성능을 지니고 있어 터치 패널용 전극으로 응용할 수 있다. 따라서 본 논문에서는 ESD 공정을 이용하여 ITO 대체가 가능한 터치패널용 투명전극을 형성하였다. 전도성 고분자의 코팅 두께에 따라 전기적인 특성이 변화하지만 투과도 80%를 전후로 면저항이
$60{\sim}80{\Omega}/{\Box}$ 의 성능이 나타남을 확인할 수 있었다. 또한 코팅된 투명 전도막을 이용하여 터치패널용 모듈 제작을 통해 동작 여부도 확인할 수 있었다. -
플라이 휠 에너지 저장장치(Flywheel Energy Storage System: FESS)는 전기 에너지를 회전 운동 에너지로 저장하였다가 필요시 회전 운동에너지를 전기 에너지로 변환하여 재사용 가능한 에너지 저장장치 이다. 최근 전력 변환 기술의 발전으로 인하여 플라이휠 에너지 저장 장치의 에너지 입출력 속도가 빨라지고 대용량의 에너지를 저장할 수 있게 되었다. 본 논문에서는 이러한 플라이휠 에너지 저장 장치의 전력 입출력 특성을 이용하여 전력 시스템에서 발생하는 저주파 진동(Low frequency oscillation)을 억제하는 방안을 제시 하여 안정도를 향상 시키고자 하였다. 전력 시스템은 발전조건, 전송조건, 부하조건에 따라 동작 조건이 지속적으로 변하고 있다. 이러한 동작 환경 변화는 전력 시스템에 대한 수학적인 표현과 실제 전력계통간의 차이가 발생하기 때문에 정확한 제어 목적을 달성하기가 힘들다. 따라서 본 논문에서는 제어기 설계 단계에서 전력 계통의 불확실성을 고려할 수 있는
$H_{\infty}$ 제어 기법을 이용하여 플라이휠 에너지 저장장치를 위한 강인 제어기를 설계 하였다. 제안한 플라이휠 에너지 저장장치의 강인 제어기의 유용성을 입증하기 위하여 1기 무한대 모선에 적용한 결과를 비선형 시뮬레이션을 통하여 다양한 외란이 발생한 경우에 외란 억제 성능과 강인성에 대하여 고찰 하였으며, 제안한 방식이 기존의 전력계통 안정화 장치(Power system stabilizer: PSS) 보다 효율적이며 전력계통의 안정도 향상에 크게 기여함을 보이고자 하였다. -
Effect of heat pump performance improvement by use of thermal tank with temperature seperation plateThis study was carried out in order to estimate the effect of heat pump performance by use of thermal tank with 3 seperation plates which were able to divide thermal tank into 3 chambers that have different temperatures levels. For testing the effect of developed thermal tank which was installed for supplying the heat to the paprika greenhouse in Jinju city. The volume of thermal storage tank was designed for
$110m^3$ which was able to cover 30% of heating capacity. The temperature difference was 3 degree Celcius between high temperature and low temperature when only heating circulation was made from heat pump to thermal tank. but 5.5 degree Celcius difference was made when heating circulation of heat pump to thermal thank and hot water supplying circulation of thermal tank to greenhouse was done simultaneously. As a result of this study showed that COP of heat pump was increased by 15% or more than that of using normal thermal tank because heat pump was able to take 3 ~ 5 degree Celcius lower thermal thank water constantly. -
Fossil fuel was a major energy resource but the consumption of fossil fuel will decrease gradually because of limited deposits and non-environmental features. In contrast, because the renewable energy resources are infinite and sustainable, their consumption has increased annually. To promote the supply of these infinite natural energy we have to develop more efficient and inexpensive heat recovery system. In this study a simple device was designed as a heat exchanger, that is a direct contact heat exchanger. This heat exchanger was manufactured in cylindrical shape with height of 1,500 mm and diameter of 1,000 mm. To test the efficiency of this heat exchanger, it was connected to the evaporator of heat pump system. During the experimental tests, the humid air of
$10{\sim}30^{\circ}C$ was supplied to this air-to-water heat exchanger and then the water flow rate was set to 2500~3500 L/h. Heat recovery rate of this heat exchanger increased in proportion to entering air temperature and water flow rate. -
The residential Fuel Cell system has high efficiency of 85% with transferring natural gas to electrical power and heat, directly and it is a friendly environmental new technology in that
$CO_2$ emission can reduce 40% compared with conventional power generator and boiler. The residential fuel cell system consists of two main parts which have electrical and hot storage units. The electrical unit contains a fuel processor, a stack, an inverter, a control unit and balance of plant(BOP), and the cogeneration unit has heat exchanger, hot water tank, and auxiliaries. 5kW class fuel process was developed and tested from 2009, it was evaluated for long-term durability and reliability test including with improvement in optimal operation logic. Stack development was crried out through improvement of design and evaluation protocol. Development of system controller was successfully accomplished through strenuous efforts and original control logic was optimized in 5kW class PEMFC system. In addition, we have been focused on development of system process and assembly technology, which bring about excellent improvement of reliability of system. The 5kW class PEMFC system was operated under dynamic conditions for 1,000 hours and it showed a good performance of total efficiency and durability. -
1kW급 가정용 연료전지 블로어는 다이어프램방식에 의해 고압 및 일정유량의 가스를 이송시키는 역할을 하고 있다. 본 연구에서는 연료전지 중 연료승압블로어를 대상으로 흡입 및 토출시의 다이어프램 캐비티(Cavity) 내의 공기유동 특성을 수치해석을 적용하여 평가하였다.
-
본 연구에서는 SOFC 시스템 설계기술 개발을 위한 기초 연구로서 전산해석을 이용한 SOFC 성능예측 기법을 개발하였다. 기본설계 단계에서 SOFC의 성능을 개략적으로 예측할 수 있는 1차원 예측 모델을 정립하였으며, 온도, 조성, 전해질, 전극 두께 등을 비롯한 다양한 조건 변화에 따른 성능예측을 수행하여 실험값과 비교한 결과 최대전력밀도 조건에서 23%의 오차를 갖는 것으로 나타났다. 또한 Stack 제작단계에서 다양한 운전조건과 형상변화에 따른 SOFC 성능 변화를 예측할 수 있는 3차원 해석기법을 정립하였으며, 최대전력밀도에서 5.1%의 오차를 보였다. 포괄적인 열 및 물질 전달 현상과 전기화학반응을 3차원적으로 해석함으로써 보다 정확한 예측이 가능하였다. 또한 수소와 적당량의 수분을 함께 공급할 경우 SOFC 성능이 향상되는 것으로 나타났다. 본 연구에서 개발된 기술을 활용할 경우 시제품 제작 전에 전지시스템의 성능을 미리 예측할 수 있으므로, 향후 제품 개발시 제작비용 절감과 설계기간 단축에 기여할 수 있을 것으로 기대된다.
-
본 연구는 아연/공기전지 설계기술 개발을 위한 기초 연구로서 전산해석을 이용하여 전해질 유동에 따른 아연/공기전지의 성능 예측에 관한 것이다. 전산해석모델은 전기화학 방정식과 유체유동 방정식으로 구성하였으며, 화학종 반응에 관한 지배방정식으로는 Nernst-Planck식을 이용하였고 전극표면의 전기화학반응은 Butler-Volmer식을 이용하였다. 또한 유체유동 방정식은 Navier-Stoke식을 적용하여 전해질 유동에 따른 전기화학적 성능 변화를 모사하였다. 아연/공기전지 성능 평가 실험으로부터 얻은 I-V 곡선과 전산해석결과와의 비교/분석을 통하여 전기화학모델의 타당성을 검증하였으며, 유체 유동 방정식과의 연동해석을 적용하여 전해질 유입 위치 및 유입 속도에 따른 아연/공기전지의 성능 변화를 조사하였다. 아연/공기전지의 성능은 전해질 유입 위치가 아연극에 가까울수록, 유입 속도가 빠를수록 향상되는 것을 확인할 수 있었다.
-
According to green growth's policy, green-home dissemination's projects are promoting. Among them, stationary fuel cell systems are receiving attention due to high efficiency and clear energy. But it need absolutely to develop cost down technologies and improve system durability for commercialization of the fuel cell system. To achieve this objectives, in 2009, the Korean Government and "Korea Institute of Energy Technology Evaluation and Planning(KETEP)" launched into the strategic development project of BOP technology for practical applications and commercializations of stationary fuel cell systems, named "Technology Development on Cost Reduction of BOP Components for 1kW Stationary Fuel Cell Systems to Promote Green-Home Dissemination Project". This paper introduces a summary of improved BOP performances that has been achieved through the 2nd year development precesses(2010.06~2011.05) base on 1st year development precesses(2009.06~2010.05). The major elements for fuel cell systems are cathode air blowers, burner air blowers, preferential oxidation air blowers, fuel blowers, cooling water pumps, reformer water pumps, heat recovery pumps, mass flow meters, electrical valves, safety valves and a low-voltage inverter. Key targets of those elements are the reduction of cost, power consumption and noise. Invert's key targets are development the low -voltage technologies in order to reduce the number of unit cell in fuel cell system's stack.
-
Stainless steel bipolar plates have many advantage such as high electrical conductivity and mechanical strength and low fabrication cost. However, they need a passivation layer due to low corrosion resistance under PEM fuel cell operation condition. In this study, polyphenyene sulfide(PPS)/carbon composite coated stainless steel bipolar plates were fabricated by compression molding method after PPS/carbon composite sprayed on the stainless steel plate. PPS and carbon were chosen as the binder and conductive filler of passivation layer, respectively. The interfacial contact resistance and corrosion resistance of PPS/carbon composite coated stainless steel bipolar plates were investigated and compared to the stainless steel. The PPS/carbon composite coated stainless steel compared to stainless steel was improved interfacial contact resistance. The results of the potentiodynamic and potentiostatic measurements also showed that the PPS/carbon composite coated stainless steel did not corroded under PEM fuel cell operating conditions.
-
연료전지 분리판은 연료, 공기, 수분이 흐를 수 있는 채널들이 포함되어 있으며, 전지들에 의해서 생산되는 전류를 흐르게 할 수 있는 전기전도성을 가져야 할 필요가 있다. 일반적인 금속판들은 연료전지 스택 내의 산성 분위기에 존재해야 하기 때문에 표면 부식이 쉽게 발생한다. 그라핀(graphene)은 우수한 전기전도성을 가지고 있을뿐만 아니라 물리화학적 내식성 및 내구성을 가지고 있어 연료전지 분리판으로서 응용이 가능할 것으로 판단된다. 본 연구에서는 일반적으로 널리 사용하고 있는 스테인리스강(stainless steel)을 모재로 사용하였으며, 그라핀을 전기분무법(electro spray coating)으로 코팅하여 스테인리스강의 내식성 및 전기전도성을 동시에 향상시키고자 하였다. 그라핀은 에탄올을 용매로 사용하여 분산하였으며, 분산제로 소량의 다이페닐다이에톡시실란(diphenyldiethoxysilane)을 첨가하여 코팅용액을 제작하였다. 코팅공정은 15kV 전압을 가하여 1시간동안 코팅을 진해하였으며, 그라핀-스테인리스강 모재의 미세구조를 전자현미경과 광학현미경을 통하여 관찰하였다. 또한 X-선 회절분석법을 이용하여 그라핀의 결정구조를 분석하였다. 한편 스택의 내부와 유사한 산화성 분위를 모사하기 위해
$80^{\circ}C$ 의 0.1N$H_2SO_4+2ppm\;F^-$ 용액에서 내식성 실험을 수행하였고, 면간접촉저항도 측정하였다. 그라핀이 코팅된 스테인리스강 시편은 고분자전해질 연료전지 분리판의 요구조건을 만족하였으며, 연료전지 분리판으로서의 적용가능성을 확인하였다. -
세계 각 국에서는 선진국을 중심으로 기후변화와 치솟는 유가에 대응하기 위하여 다양한 에너지원의 확보를 위해 부단히 노력하고 있다. 특히, 신재생에너지원 중 에너지 지속성이 가장 우수한 연료전지의 경우 1kW급 건물용 연료전지시스템이 도시가스 인프라가 가장 우수한 한국 및 일본을 중심으로 상용화에 가장 근접해 있는 실정이다. 일본의 경우 가정용 연료전지시스템 '에너팜'의 일부 제품이 올해부터 200만엔대로 가격을 내려 보급되어질 예정이고, 아직은 경제성이 떨어지지만 연료전지 조기 상용화를 위해 시스템 가격저감을 통한 기술개발이 한창이다. 또한 700W급 고체산화물형 연료전지시스템을 세계에서 처음 시판 계획을 가지고 있다. 국내의 경우 2009년도부터 시작된 '그린홈 보급확대를 위한 건물용 연료전지 보조기기 가격저감 기술개발'연구를 통해 블로워, 밸브, 유량계 및 펌프 등의 보조기기의 단가를 낮추고자 기술개발에 박차를 가하고 있다. 이에 따른 연료전지 부품 가격저감 기술이 국내 건물용 연료전지 시장보급의 활력소가 되기를 기대한다. 본 연구에서는 건물용 연료전지의 보조기기인 블로워의 가격저감을 위한 연구의 일환으로 블로워의 안전성능 평가를 통한 보조기기의 가격저감 및 안전성을 확보하고자 한다. 1kW급 건물용 연료전지시스템의 여러 블로워 중 도시가스용 연료승압 블로워, 선택산화 공기 블로워, 버너 공기 블로워 및 캐소드 공기 블로워의 안전성능 평가를 수행하였고, 평가결과의 공유를 통하여 국내 블로워 제조사의 설계방향을 제시하고 연료전지시스템의 안전성을 확인하고자 한다. 특히, 내구성, 기밀, 가혹조건시험 및 소음, 진동, 습도, 온도와 같은 내주위환경시험 등의 평가결과 비교를 통하여, 연료전지 부품 인증기준을 재정립하여 연료전지 부품산업의 조기 활성화를 도모하고자 한다.
-
고분자 전해질 연료전지 (PEMFC)의 핵심 부품 중의 하나인 Bipolar Plate (분리판)을 제조하기 위해서 고분자/그라파이트 복합재료를 사용하였다. 고분자 매트릭스로는 경화시 뛰어난 화학적, 기계적 특성을 갖는 에폭시를 채택하였고, 전기 전도성을 부여하기 위해 그라파이트를 도입하였으며, 에폭시 수지의 내충격성을 향상시키기 위해서 Carbon Fiber를 채택하였다. 에폭시 분말과 그라파이트 분말, 그리고 1cm 정도의 길이를 갖는 Carbon Fiber을 믹서에 넣고 균일하게 혼합하였다. 이 혼합물을 이형제 처리된 몰드에 주입하고, Hot Press를 사용하여 가열, 가압 (
$150^{\circ}C$ , 4 ton/$cm^2$ , 2시간)하면서 경화시켰다. 일정 비율로 고정된 에폭시/그라파이트 계에 Carbon Filber의 혼합 비율을 변화시키면서 전기적, 물리적 성질의 변화를 연구하였다. -
고분자전해질 연료전지 (PEMFC)의 가격 결정 요인 중 막 전극 접합체 (MEA)가 차지하는 비중은 약 45%정도이며, 이것을 구성하는 주요 부품인 기체 확산층 (GDL)은 carbon paper나 carbon cloth 형태가 사용되고 있다. 그렇지만 GDL을 제조하는 공정은 매우 복잡하고, 그 가격이 너무 높은 단점이 있다. 본 연구에서는 카본블랙, 흑연 등의 탄소화합물과 polymer binder를 이용하여 단순화된 공정으로 GDL을 제조하였다. 또한, GDL의 물리적 특성이 전극 성능에 미치는 영향을 분석하기 위하여 표면 morphology, 접촉각 및 표면에너지, 전기전도도, 기체투과도, porosity, pore distrivution 등을 측정하였고, 각각의 GDL 표면에 동량의 Pt 촉매를 도포하여 MEA를 제작한 후 그 성능을 평가하였다.
-
To obtain higher power efficiency of Residential Power Generation System(RPG), it is needed to operate system on optimized stoichiometric ratio of fuel and air. In this paper, optimizing stoichiometric ratio of fuel/air is conducted through systematic experiments and modeling. Based on fundamental principles and experimental data, constraints are chosen. Using these stoichiometric ratios as decision variables, maximum power efficiency of system could be found. As a result of research, power efficiency of RPG system is improved.
-
In this work, graphite nanofibers (GNFs) were prepared for using catalyst supports in fuel cells. The GNFs were chemically activated to obtain high surface area and small pore diameter with different potassium hydroxide (KOH) amounts, i.e., 0, 1, 3, 4, and 5 g as an activating agent. And then Pt-Ru was deposited onto activated GNFs (A-GNFs) by chemical reduction method. The characteristics of Pt-Ru catalysts deposited onto A-GNFs were determined by specific surface area and pore size analyzer, X-ray diffraction (XRD), transmission electron microscopy (TEM), and inductive coupled plasma-mass spectrometer (ICP-MS). The electrochemical properties of Pt-Ru/A-GNFs catalysts were also analyzed by cyclic voltammetry (CV) experiments. From the results, the A-GNFs carbon supports activated with 4 g of KOH (A4g-GNFs) showed that the highest specific surface areas. In addition, the A4g-GNFs led to uniform dispersion of Pt-Ru onto A4g-GNFs, resulting in the enhancement of electrochemical activity of Pt-Ru catalysts.
-
In this work, ordered mesoporous carbons (OMCs) were prepared by the conventional templating method using mesoporous silica (SBA-15) for Pt-Ru catalyst supports in fuel cells. The influence of surface modification on carbon supports on the electrochemical activities of Pt-Ru/OMCs was investigated with different pH. The neutral-treated OMCs (N-OMCs), base-treated OMCs (B-OMCs), and acid-treated OMCs (A-OMCs) were prepared by treating OMCs with 2 M
$C_6H_6$ , 2 M KOH, and 2 M$H_3PO_4$ , respectively. The surface characteristic of the carbon supports were determined X-ray photoelectron spectroscopy (XPS). The electrochemical activities of the Pt-Ru catalysts had been enhanced when the OMCs supports were treated by basic or neutral agents, while the electrochemical activities had been decayed for the A-OMCs supported Pt-Ru. -
In this work, multi-functional groups, i.e., nitrogen and oxygen, contained microporous carbons (MF-MCs) were prepared by the one step carbonization of the poly(vinylidene chloride-co-acrylonitrile-co-methyl methacryalte) (PVDC-AN-MMA) without activation. The electrochemical performance of MF-MCs was investigated as a function of carbonization temperature. It was found that MF-MCs had a high specific surface area over
$800m^2/g$ without additional activation, resulting from the micropore's formation by the release of chlorine groups. In addition, although functional groups decreased, specific surface area was increased with increasing carbonization temperature, leading to the enhanced electrochemical performance. The pore size of the carbon distributed mainly in small micropore of 1.5 to 2 nm, which was idal for aqueous electrolyte. Indeed, the unique microstructure features, i.e. high specific surface area and optimized pore size provided high energy storage capability of MF-MCs. These results indicated that the microporous features of MF-MCs lead to feasible electron transfer during charge/discharge duration and the presence of nitrogen and oxygen groups on the MF-MCs electrode led to a pseudocapacitive reaction. -
In this work, graphene was prepared by modified Hummers method and prepared graphene was applied to electrode materials for supercapacitor. In addition, to enhance the electrochemical performance of graphene, carbon black was deposited onto graphene via chemical reduction. The effect of the carbon black content incorporated on the electrochemical properties of the graphene-based electrodes was investigated. It was found that nano-scaled carbon black aggregates were deposited and dispersed onto the graphene by the chemical reduction of acid treated carbon black and graphite oxide. From the cyclic voltammograms, carbon black-deposited graphene (CB-GR) showed improved electrochemical performance, i.e., current density, quicker response, and better specific capacitance than that of pristine graphene. This indicates that the carbon black deposited onto graphene served as an conductive materials between graphene layers, leading to reducing the contact resistance of graphene and resulted in the increase of the charge transfer between graphene layers by bridge effect.
-
In order to achieve high performance and low cost for commercial applications, the development of membrane electrode assemblies (MEA), in which the electrochemical reactions actually occur, must be optimized. Expensive platinum is currently used as an electrochemical catalyst due to its high activity. Although various platinum alloys and non-platinum catalysts are under development, their stabilities and catalytic activities, especially in terms of the oxygen reduction (ORR), render them currently unsuitable for practical use. Therefore, it is important to decrease platinum loading by optimizing the catalysts and electrode microstructure. In this study, we prepared several different MEAs (non-uniform Nafion
$^{(R)}$ ionomer loading electrode) which have dual catalyst layers to find the optimal Nafion$^{(R)}$ ionomer distribution in the electrodes. We changed Nafion$^{(R)}$ ionomer content in the layers to find the ideal composition of the binder and Pt/C in the electrode. For MEAs with various ionomer contents in the anodes and cathodes, the electrochemical activity (activation overpotential) and the mass transport properties (concentration overpotential) were analyzed and correlated with the single cell performance. The dual catalyst layers MEA showed higher cell performance than uniformly fabricated MEA, especially at the high current density region. -
Solid oxide fuel cells(SOFCs) can convert the chemical energy of fuel into electricity directly. With the rising fuel prices and stricter emission requirement, SOFCs have been widely recognized as a promising technology in the near future. In this study, lean premixed flame using the orifice swirl burner was analyzed numerically and experimentally. We used the program CHEMKIN and the GRI 3.0 chemical reaction mechanism for the calculation of burning velocity and adiabatic flame temperature to investigate the effects of equivalence ratio on the adiabatic flame temperature and burning velocity respectively. Burning velocity of hydrogen was calculated by CHEMKIN simulation was 325cm/s, which was faster than that of methane having 42 cm/s at the same equivalence ratio. Also Ansys Fluent was used so as to analysis the performance with alteration of swirl structure and orifice mixer structure. This experimental study focused on stability and emission characteristics and the influence of swirl and orifice mixer in Solid Oxide Fuel Cell Systme burner. The results show that the stable blue flame with different equivalence ratio. NOx was measured below 20 ppm from equivalence ratios 0.72 to 0.84 and CO which is a very important emission index in combustor was observed below 160 ppm under the same equivalence region.
-
Water transport through the microporous membrane was modeled considering capillary condensation as well as capillary flow in porous media as a function of pore diameter and relative humidity at the surface. The present model was adopted by the numerical simulation of non-isothermal, non-homogenous flow in a shell and tube typed gas to gas membrane humidifier for PEMFC (proton exchange membrane fuel cell) and the result shows good agreement with experimental data.
-
저온에서 양이온 고분자막을 사용하는 고분자 연료전지의 경우 뛰어난 성능과 다양한 응용분야로 인해 많은 연구와 실증이 이루어지고 있지만 공기극에서의 느린 산소 환원반응으로 인해 백금과 같은 귀금속의 사용이 불가피하고 백금의 제한된 매장량과 높은 가격으로 인해 상용화가 늦어지고 있다. 그래서 많은 연구자들이 합금 촉매 또는 비귀금속 촉매를 이용한 전극 개발에 집중하고 있다. 알칼리 분위기에서 저가의 전이 금속들이 백금과 비슷한 활성을 보이고 고체 음이온 교환막이 개발됨에 따라 최근 알칼리 연료전지가 다시금 큰 주목을 받고 있다. 그러나 고분자 연료전지와는 달리 아직 촉매나 전해질막, 이오노머의 특성 및 메커니즘에 관해 별로 알려진 것이 없다. 본 연구에서는 직접 개발한 세공충진막 형태의 탄화수소계의 음이온 교환막과 비귀금속 공기극 촉매를 이용하여 막전극접합체(MEA)를 개발하였고 촉매 및 이오노머 함량과 같은 전극 조성, 막전극접합체의 제조 및 체결, 가습이나 가스조성 등의 단위전지 운전조건과 같은 다양한 변수에 대해에 최적 조건을 도출하고자 하였다. 공기극 촉매는 Cu-Fe/C를 이용한 상용 촉매를 이용하였고 이오노머의 경우는 탄화수소계의 상용 제품을 사용하였으며 음이온 교환막에 전극층을 형성하기 위해서는 스프레이 공정을 이용하였다. 단위전지를 통해 성능을 확인하였고 임피던스 및 CV를 통해 전기화학적인 특성을 규명하였다. 조건의 최적화를 통해 상당한 성능 향상을 이루었으나 추가적인 성능 향상 및 내구성 확보 등에 대해 계속적인 실험을 진행할 예정이다.
-
Park, Sungho;Kal, Hanjoo;Jeong, Youngsik;Lee, Sanghoon;Lee, Jaejun;Oh, Yongmin;Kim, Seonhwa 97.2
본 연구는 연료전지 중 용융탄산염을 전해질로 하는 MCFC의 MBOP에 포함된 부품으로 매우 중요한 역할을 하는 가습기와 이때 발생되는 폐열을 회수하기 위한 장치인 HRU에 관한 것이다. 가습기는 연료와 물이 가습기 상부로 유입되어 가습기 하부로 유입되는 배가스와 열교환을 하면서 물이 스팀화 되어 연료가 가습된 상태로 가습기 출구로 일정온도를 유지하며 배출된다. 또한 HRU는 가습기에서 배출된 고온의 배가스를 물을 이용하여 열교환을 통해서 열을 회수하여 난방 및 온수로 사용할 수 있는 열교환 장치를 말한다. 먼저 이들의 특성을 파악하기 위해 가습기 및 HRU를 설계, 제작하여 각각의 특성을 확인하였다. 가습기와 HRU의 성능 향상을 위해 먼저 열교환부에 적용될 튜브의 수치해석적 분석을 통해서 최적의 열전달 성능을 얻을 수 있는 가습기 및 HRU를 설계, 제작하였으며 이들의 성능을 파악하기 위해 120,000kcal/h 용량을 테스트 할 수 있는 장치를 구축하여, 이들의 열전달 특성, 압력강하, 회수 열량, 가습기 온도 등의 특성을 파악하였다. 이 장치를 통해서 확인된 가습기와 HRU의 특성은 수치해석을 통해서 얻은 값과 거의 유사함을 확인할 수 있었으며, 가습 성능도 효과적으로 달성할 수 있었다. 가습기와 HRU의 특성 중 압력강하 부분은 지속적인 연구가 필요한 부분이며, 가습기와 HRU의 일체화를 통하여 소형화 및 설치공간 축소 효과를 얻을 것으로 본다. -
We present here an isothermal, one-dimensional, steady-state model for a solid alkaline fuel cell (SAFC) with an anion exchange membrane. The conducting ions now move from the cathode to the anode in SAFC. The water is produced at the anode and is also a stoichiometric reactant at the cathode as well as hydrogen and oxygen. In the present model, a net-water-per-proton flux ratio can be predicted and the water transport in the SAFC is explained for various operating conditions.
-
For optimal performance of a proton exchange membrane fuel cell (PEMFC), the membrane electrode assembly (MEA) requires hydration, and the membrane's conductivity depends on water content. A humidifier is required to ensure that the reactant gas, usually hydrogen and air, is hydrated before entering the fuel cell. Dry membrane operation or improper hydration causes performance degradation. Typically, the humidification of a fuel cell is carried out by means of an internal or external humidifier. A membrane humidifier is applied to the external humidification of transportation or residential power generation fuel cell due to its convenience and high performance. In this study, The experiments were constructed with a plate-type membrane humidifier in terms of geometric parameters and operating parameters. The results show that the temperature and pressure, the channel length, the membrane thickness and gas flow rate are critical parameters affecting the performance of the humidifier.
-
Electrochemical impedance spectroscopy(EIS) are using widely as a useful technique mainly in the field of electrochemical for the analysis of electrode reactions or characteristics of the composites. The response analysis of the systems technique provides comprehensive informations about the characteristic and structure of complex and internal reaction. The EIS is the method to measure impedance of the measurement target classified by the frequency, it select the equivalent impedance model to give same response from the result and it calculate the parameter. Therefore, the chemical reaction inside the fuel cell is to modeling to electrical impedance. And as repeating the same experiment in each of the operating point, we can get each different parameter. As a result, we can establish the equivalent impedance model in each operating point. Therefore, if we use these models, we can evaluate the fuel cell without the internal design parameter of the fuel cell as required in existing modeling. The EIS is used typically technique for distinguish status of fuel cell called SOH(State Of Health). When the fuel cell is degradation, Efficiency and health of the fuel cell is reduced because internal impedance is increase. As usage of these principles, we can evaluate state of fuel cell through the impedance analysis of fuel cells. In this study, we are presents EIS distinction system and algorithm for residential fuel cell systems. At the time of the fuel cell installation in the fields, the EIS system and proposed algorithm will be able to apply as technique for efficiency and performance evaluation about fuel cell system.
-
Park, Jongwook;Yang, Seoungryoung;Chung, Chunsub;Park, Sungho;Kal, Hanjoo;Jeong, Youngsik;Lee, Sanghoon;Lee, Jaejun;Oh, Yongmin;Kim, Seonhwa 100.2
본 연구과제는 유망상품인 "발전용 MCFC 모듈형 BOP" 중 가습기 내부에 장착되는 연료-물 Mixing 시스템을 개발하는 것이다, 가습기 내부에서 공급된 연료-물은 연료전지 스택(Stack)으로부터 가습기로 유입된 고온의 가스로부터 열을 공급 받아 증발 및 혼합과정을 거치게 되며, 스팀-연료 혼합기로 형성되어 개질기(reformer)로 공급되게 된다. 이때, 물과 연료의 공급 상태에 따라 균일한 스팀-연료 혼합기가 형성되는지가 결정되며, 경우에 따라서는 고온의 가습기 내부의 국부적 온도분포의 큰 차이를 발생시켜 용접부의 균열을 발생시킬 수도 있기 때문에, 가습기의 설계와 함께 중요한 장치로 여겨진다. 본 연구에서는 다양한 가습기에 적용이 가능한 Mixer 모델을 설정하고, Analytic calculation을 통한 노즐설계와 1pass/Full scale 성능 실험 장치를 통해 상용화를 목표로 추진 되었으며, 특히 노즐별 유량분배 변동율은${\pm}3%$ 이내로 달성하고, 스팀/연료 공급 비율은 2:1 이내로 달성할 수 있는 시스템을 구축하게 될 것이다. 최종적으로 개발 완료 시 다양한 가습기에 직접 장착하여 운전이 가능할 수 있도록 실용화에 중점을 두고, 보다 안정적인 성능을 나타낼 수 있는 제품 개발이 가능하리라 사려된다. -
Kim, Chan Seok;Lee, Seunghun;Tak, Sung Ju;Choi, Suyoung;Boo, Hyun Pil;Lee, Jeong Chul;Kim, Donghwan 103.1
실리콘 이종접합 태양전지에서 계면 결함 밀도는 효율을 결정하는데 가장 중요한 요인으로 작용한다. 계면 결함은 캐리어의 재결합 위치로 작용하여, 계면 결함 밀도가 증가하면 재결합 속도가 증가하게 된다. 흡수층으로 사용되는 실리콘 웨이퍼 (결정질 실리콘)를 가능한 깨끗하게 세정함으로써, 또한 emitter로 쓰이는 비정질 실리콘을 낮은 데미지로 증착하여 계면 결함 밀도를 감소 시킬 수 있다. 이러한 계면 결함 밀도의 감소가 어떠한 변화로 인해 태양전지 특성에 영향을 주는지 시물레이션을 통해 알아보았다. n-type 웨이퍼에 p-type 비정질 실리콘을 emitter로 하여 TCO/p/i/n-type wafer/i/n/TCO/metal의 구조를 적용했고, wafer 전면과 i로 쓰인 무첨가된 비정질 실리콘 간의 계면 결함 밀도를 변수로 적용했다. 그 결과, 계면 결함 밀도가 감소함에 따라 재결합이 감소하여 태양전지 특성이 증가하는 측면도 있지만, 흡수층의 장벽 (barrier height)이 높아져 재결합을 더욱 감소시킴으로 인해 태양전지 특성이 증가함을 알 수 있었다. -
Jang, JiHoon;Han, Kang-Soo;Cho, Jun-Sik;Lee, Heon;Park, Hai Woong;Song, Jinsoo;Lee, Jeong Chul 103.2
비정질 실리콘 태양전지의 효율을 증가하기 위하여 많이 사용되는 방법 중 하나는 입사되는 빛의 산란을 증가하여 태양전지의 광흡수를 증가시키는 방법이다. 이를 위하여 양극전극으로 사용되는 TCO층의 일정한 패턴 처리를 통하여 광산란을 증가시키는 방법이 사용되고 있다. 본 연구에서는 나노 임프린트 리소그래피방법을 사용하여 Ag 나노로드를 증착한 기판을 제조하고 이를 비정질 실리콘 태양전지에 적용하였다. 실험결과, 그림과 같이 높이와 너비가 300nm 정도로 일정한 패턴의 Ag 나노로드를 제조하였다. 또한, 그 위에 증착된 Si 박막의 경우, 나노로드 전체를 감싸는 돔 형태로 성장하였다. 이와 같은 나노로드 위에 substrate n-i-p 구조의 비정질 박막 태양전지를 증착하고 그 특성변화를 분석하고자 하였다. -
Kim, Y.H.;Kim, I.K.;Pyun, S.C.;Ham, C.W.;Kim, S.B.;Park, W.S.;Park, C.K.;Kang, H.D.;You, C.;Kang, S.H.;Kim, S.W.;Won, D.Y.;Choi, Y.;Nam, J.H. 104.1
가볍고, 유연성(flexibility)을 갖는 박막(thin film)형 플랙서블 태양전지(flexible solar cell)는 상황에 따른 형태의 변형이 가능하여, 휴대가 간편하고, 기존 혹은 신규 구조물의 지붕(rooftop)등에 설치가 용이하여, 차세대 성장 동력 분야에서 각광받고 있다. 그러나 아직까지 플랙서블 태양전지는 제작시 열에 의한 기판의 변형, 기판 이송시 너울 현상, 대면적 패터닝(patterning) 기술 등 많은 어려움 등으로 웨이퍼나 글라스 기판에 제조된 태양전지 대비 낮은 광전환 효율을 갖는다. 따라서 본 연구에서는 플랙서플 태양전지 성능개선을 위해 3.5세대급 ($450{\times}450cm^2$ ) 스퍼터(sputter), 금속유기 화학기상장치 (MOCVD), 플라즈마 화학기상장치 (PECVD), 레이저 가공장치 (Laser scriber)를 이용하여 a-Si:H/a-SiGe:H 이중접합(tandem)을 갖는 태양전지를 제작하였고, 광 변환효율 특성을 평가하였다. 전도도(conductivity), 라만(Raman)분광 및 UV/Visible 분광 분석을 통하여 박막의 전기적, 구조적, 광학적 물성을 평가하여 단위박막의 물성을 최적화 했다. 또한 제작된 태양전지는 쏠라 시뮬레이터 (Solar Simulator)를 이용하여 성능 평가를 수행하였고, 상/하부층의 전류 정합 (current matching)을 위해 외부양자효율 (external quantum efficiency) 분석을 수행하였다. 제작된 이중접합 접이식 태양전지로 소면적($0.25cm^2$ )에서 8.7%, 대면적($360cm^2$ 이상) 8.0% 이상의 효율을 확보하였으며, 성능 개선을 위해 대면적 패턴 기술 향상 및 공정 기술 개선을 수행 중이다. -
세계적으로 환경오염이 심각해짐에 따라 친환경적으로 에너지를 생산하는 기술이 주목받고 있다. 그 중에서도 태양광을 이용하여 전력을 생산하는 태양광 태양전지의 경우 원리가 간단하고 에너지원의 수급이 용이하다는 장점으로 인하여 많은 연구가 진행되고 있다. 그러나 태양광 태양전지의 경우, 태양전지 기판에서의 반사로 인하여 발전 효율이 낮아는 문제점이 있다. 이를 해결하기 위해 텍스처링 공정을 통해 태양전지 기판에서의 반사를 줄이고 태양전지의 효율을 증가시키는 방법이 이용되고 있다. 본 연구에서는 나노 돌기를 가진 저반사 패턴을 이용하여 태양전지용 실리콘 기판을 제작함으로써, 태양전지 기판에서의 반사를 줄이고자 하였다. 나노 돌기를 가진 저반사 패턴이 형성 된 태양전지용 실리콘 기판을 제작하기 위해 ICP 장비를 이용한
$Cl_2$ 플라즈마 식각공정을 진행하였다. 먼저 Au agglomeration 기술을 이용하여 Au nano particle을 실리콘 기판 위에 형성 후, 이를 식각 마스크로 이용하여 ICP 식각을 진행하였다. 이어서 나노 돌기가 형성 된 실리콘 기판 위에$Cl_2$ 플라즈마에 내식각성이 우수한 레지스트를 이용하여, 나노 임프린트 리소그래피 기술을 통해 저반사 패턴을 형성하였다. 이 방법으로 형성 된 저반사 패턴을 식각 마스크로 사용하여 앞의 공정과 동일한 조건으로 실리콘 기판을 식각하였다. 최종적으로 agglomerated Au particle과$Cl_2$ 플라즈마에 내식각성이 우수한 레지스트를 이용하여 나노 돌기를 가진 저반사 패턴이 형성된 실리콘 기판을 제작하였다. -
To enhance the performance of photovoltaic a-Si:H solar cells with a hybrid-type light absorbing structure of single crystal silicon nanoparticles (Si NPs) in a-Si:H matrix, single crystal Si NPs were produced by laser pyrolysis. The Si NPs were synthesized by
$SiH_4$ gas decomposition using a$CO_2$ laser. The properties of Si NPs were controlled by process parameters such as$CO_2$ laser power, reactive gas pressure, and$H_2/SiH_4$ gas flows. The crystalline properties and sizes of Si NPs were analyzed by High Resolution Transmission Electron Microscopy (HRTEM). The sizes of Si NPs were controllable in the range of 5-15 nm in diameter and the effects of process parameters of laser pyrolysis were systematically investigated. -
화비정질 실리콘의 빛에 의한 노화현상 (light-induced degradation; LID)은 이미 1977년 보고된 Staebler-Wronski 효과에 의해서 확인된 바 있다. 이는 비정질 실리콘이 빛에 노출될 때, 이미 포함되어 있는 수소원자가 빛 에너지에 의해서 이동하게 되고, 이로 인해서 생성 또는 소멸되는 댕글링 본드 때문에 일어난다. 특히, 일상적인 태양광의 노출 하에서 태양전지의 장시간 성능을 예측하는데 물리적인 이해의 부족 및 기술 환경적인 어려움이 있고, 이러한 요인들은 안정된 태양전지를 개발하는데 장해요인으로 나타난다. 그러므로 비정질 실리콘 태양전지가 장시간 태양광에 노출되어 시간이 지남에 따라서 "성능이 어떻게 변하는지?" 그리고 "이에 대한 원인은 무엇인지?" 등은 여전히 과학적으로 풀어야할 숙제로 남아있다. 본 논문에서는 비정질 실리콘으로 구성된 태양전지가 태양광에 노출될 때 시간이 지남에 따라서 (1) 성능이 어떻게 변하는지, (2) LID의 변화는 언제 안정화되는지, 그리고 (3) 성능변화에 대한 원인은 무엇인지에 대해서 논의한다. 본 논문은 장시간 빛에 노출되는 비정질 실리콘 태양전지의 성능예측에 관해서 연구하였다. 결함밀도의 운동학적 모형을 통해서 태양광 노출에 대한 태양전지 성능변화를 예측하는데 초점을 맞추었고, 이를 위해서 태양전지에 조사되는 태양광 세기, 주변온도, 등이 고려되었다. 특히, 전하운반자의 수명이 결함밀도에 의해서 결정되기 때문에 비정질 실리콘 태양전지의 빛에 대한 노화현상 (LID)이 확장지수함수 (stretched-exponential) 완화법칙을 따르는 결함밀도에 의해서 물리적으로 설명된다. 한편 이와 같은 물리적 계산의 유용성을 확인하기 위해서 동일한 태양전지에 대해서 AMPS-1D 컴퓨터 프로그램을 사용하였고, 이를 통해서 비정질 실리콘 태양전지의 빛에 대한 노화현상을 물리적 및 정량적으로 이해하였다. 본 연구에 적용되는 태양전지는 비정질 실리콘으로 구성된 pin 구조 (glass/
$SnO_2$ /a-SiC:H:B/a-Si:H/a-Si:H:P/ITO)로서 다음과 같은 특성을 갖는다: 에너지 띠간격~1.72 eV, 두께~400 nm, 내부전위~1.05 V, 초기 fill factor~0.71, 초기 단락전류~16.4 mA/$cm^2$ , 초기 개방전압 0.90 V, 초기 변환효율 10.6 %. 우리는 이와 같은 연구를 통해서 과학적으로 비정질 실리콘의 빛에 의한 노화현상을 이해하고, 기술적으로 효율 및 경제성이 높은 태양전지의 개발에 도전한다. -
The Cu(In,Ga)Se2 (CIGS) thin film solar cells have been achieved until almost 20% efficiency by NREL. These solar cells include chemically deposited CdS as buffer layer between CIGS absorber layer and ZnO window layer. Although CIGS solar cells with CdS buffer layer show excellent performance, the short wavelength response of CIGS solar cell is limited by narrow CdS band gap of about 2.42 eV. Taking into consideration the environmental aspect, the toxic Cd element should be replaced by a different material. Among Cd-free candidate materials, the CIGS thin film solar cells with ZnS buffer layer seem to be promising with 17.2%(module by showa shell K.K.), 18.6%(small area by NREL). However, ZnS/CIGS solar cells still show lower performance than CdS/CIGS solar cells. There are several reported reasons to reduce the efficiency of ZnS/CIGS solar cells. Nakada reported ZnS thin film had many defects such as stacking faults, pin-holes, so that crytallinity of ZnS thin film is poor, compared to CdS thin film. Additionally, it was known that the hetero-interface between ZnS and CIGS layer made unfavorable band alignment. The unfavorable band alignment hinders electron transport at the heteo-interface. In this study, we focused on growing defect-free ZnS thin film and for favorable band alignment of ZnS/CIGS, bandgap of ZnS and CIGS, valece band structure of ZnS/CIGS were modified. Finally, we verified the photovoltaic properties of ZnS/CIGS solar cells.
-
다층 박막 구조로 이루어진 CdS/CdTe 태양전지의 경우, 각각의 박막이 다양한 제조 공정을 거치면서 물성특성의 변화를 겪게 된다. 각각의 박막이 고온의 열처리 공정과,
$CdCl_2$ 용액 처리 및 후면 산화막 제거 공정 등을 거치게 되면서 겪게 되는 물성 변화 분석을 살펴보고자 한다. 각각의 박막 제조 방식은 일반적으로 사용되는 방식으로, CdS의 경우는 용액성장법(Chemical Bath Deposition, CBD), CdTe의 경우는 근접승화법(Closed Space Sublimaition, CSS)을 사용했으며, X-Ray Diffractometer (XRD), Raman spectroscopy, Field Emission Scanning Electron Microscope (FE-SEM), Energy Dispersive Spectroscopy (EDS), X-ray Photoelectron Spectroscopy (XPS) 등을 이용하여 분석하였다. 각각의 셀 제조 공정을 거치면서 CdS, CdTe 박막들은 결정, 광 특성, 성분 변화를 보였다. -
Kim, Soo Min;Bae, Su Hyun;Kim, Seong Tak;Kim, Hyun Ho;Park, Hyo Min;Kim, Young Do;Park, Sungeun;Tark, Sung Ju;Kim, Donghwan 107.1
현재 상용으로 많이 사용되는 p-type 태양전지는 Dopant로 사용된 Boron이$O_2$ 와 결합하면서 Light induced degradation이 발생하여 태양 전지 효율의 감소를 불러일으키는 단점이 있다. 이러한 문제를 해결하기 위하여 여러 가지 방법들이 제시되었는데 일반적으로 n-type wafer를 이용함으로써 Light induced degradation을 해결하는 방법이 주로 사용된다. n-type 태양전지를 제조함에 있어서 보다 높은 효율을 달성하기 위하여 태양전지 후면 구조에 local contact 개념을 도입하여 rear local emitter를 형성함으로써 전체적인 효율 증가를 도모하였다. 이러한 local contact을 제조하기 위해서는 전기적으로 구조적으로 고려할 사항들이 여러 가지 존재한다. 따라서 우리는 이러한 고려 사항들을 실험적인 방법으로 결정하는 것이 아니라, 정교한 변수 통제를 이용한 시뮬레이션으로 최종적인 효율 상승을 가져오는 조건을 찾으려고 한다. 이때 사용될 수 있는 시뮬레이션은 여러 가지 종류가 존재하는데 우선 상용 태양전지의 해석에 가장 많이 사용되는 PC1D프로그램이 있다. 그러나 PC1D의 경우에는 1차원의 해석만 가능하기 때문에 local contact의 2차원 이상의 구조 변화에 따른 최종적인 효율을 계산하는데 무리가 따르게 된다. 따라서 2차원 이상의 형상에 대한 분석이 가능한 프로그램을 이용하여 실제 셀에서 일어나는 현상을 더 정밀하게 모사함으로써 local contact에서 일어나는 전기적, 구조적 변화가 최종적인 효율에 어떻게 영향을 미치는지를 파악해볼 것이며, 어떤 구조를 선택하였을 때 가장 높은 효율을 달성할 수 있는지 알아보려고 한다. -
태양광발전 시스템의 성능 평가는 신뢰할 수 있는 데이터의 취득 및 분석을 통하여 발전성능을 제시할 수 있다. 발전성능에 영향을 미치는 요인으로는 일사량과 온도 등의 환경적인 요인, 시스템 구성에 따른 기술적인 요인에 의해 결정될 수 있다. 특히, 시스템 구성에 의해 결정되는 기술적인 요인은 태양전지 모듈의 어레이 손실 및 BOS의 자체 손실 등을 분석하여 전체 시스템의 발전성능을 분석하여 그 성능을 평가할 수 있다. 본 논문에서는 기 설치된 태양광발전 시스템에서 취득된 데이터를 통하여 용량별, 지역별에 따른 태양광발전 시스템의 성능 분석과 손실 원인을 분석하였다. 분석결과 시스템의 성능은 환경적인 요인과 기술적인 요인에 의해 발전성능이 달라진다는 것을 확인할 수 있었다. 본 논문의 결과는 향후 태양광 발전 시스템의 성능의 기준을 제시하는 연구를 위한 사전연구로써 유용한 자료가 되리라 믿는다.
-
KEPCO was operating power plants with diesel generators in 49 islands including Baekryeong-Do, and the generation capacity was about 66 MW in 2008. The cost of fuel is increasing by the international oil price inflation and continuous rise of oil price is predicted. For the stabilizing of electric power supply to the separate islands, renewable energy and fuel cell systems were considered. Hydrogen is made using renewable energy such as wind power and solar energy, and then a fuel cell system generates electricity with the stored hydrogen. Though the system efficiency is low, it is treated as the only way to secure the stable electric supply using renewable energy at this present. The analytic hierarchy process was used to select suitable candidate island for the system installation and 5 islands including Ulleung-Do were selected. Economic evaluation for the system composed of a kerosene generator, a wind power, an electrolysis, and a fuel cell system was conducted with levelized generation cost based on present value methode. As the result, the necessity of renewable energy combined generation system and micro grid composition in the candidated islands was confirmed. Henceforth, the development of an integration technology which connects micro grid to the total power grid will be needed.
-
A photovoltaic system is getting the spotlight for a environment-friendly energy source. But its location is limited because a lot of land is necessary for photovoltaic arrays. Nevertheless, its dissemination is rapidly increasing more than 40 % every year and exceeded about 400 MW in 2009. The radical growth of a photovoltaic system aggravated a lack of sites, so that forests and farmland were destroyed. It is demanded to make use of a vacant lot or little piece of land for the way to solve the lack of sites and improve the location requirements for a photovoltaic system. General photovoltaic arrays are consist of a single layer structure and needs enough separation distances to maximize the amount of solar radiation and to eliminate influences by the shadow of other arrays. So that a large amount of land is required for the site. The solar cell arrays with long separation distances can not be placed in a small vacant lot and its site application efficiency is low. This study optimized photovoltaic arrays as multilayered structure with movable sleeves for the efficient photovoltaic in a small site. The existing photovoltaic arrays with a single layer structure were fixed or tracking systems. In this experimental equipment, photovoltaic arrays attached to the multilayers have rectilinear movement and rotary motion using sleeves. Therefore, shadow influences were removed and the generation capacity was improved. On the simulation result, generation increased by about 30% in the same site considering shadow influences and so on.
-
This study analyzed the performance of long term operation photovoltaic system The 50 kWp grid connected photovoltaic system which was installed at KEPRI site in 1999 has been operated more than 12 years. In order to acquire long term operation characteristics of medium size photovoltaic system, the operation test data related on power generation electricity and capacity factor of 50 kWp system, which have been collected since 1999, were analysed. From the analysing results, 57.7 MWh in annual power generation electricity of 50 kWp photovoltaic system in 1999 has been decreased 49.1 MWh in 2005 and reached 38.0 MWh in 2010. In addition to, the capacity factor of 50 kWp photovoltaic system also showed 13.2 % in 1999, 11.2% in 2005 and finally reached 8.8% in 2011. The operation test data showed a trend of decreasing of generation electricity and capacity factor during the 12 years operation time and we guessed that was caused by solar cell performance degradation and decreasing of PCS system efficiency.
-
일본 Sanyo 사에 의해서 획기적으로 HIT 태양전지가 개발된 바 있다. 이러한 HIT 태양전지는 기존의 확산-접합 Si 태양전지에 비해서 저비용 고효율의 장점을 갖는다: 22% 이상의 변환효율,
$200^{\circ}C$ 이하의 공정온도, 낮은 태양전지 온도 의존도, 높은 개방전압. 한편 Sanyo사의 HIT 태양전지는 n-형 Si 웨이퍼를 이용한 반면에, 최근 미국 National Renewable Energy Laboratory는 p-형 Si 웨이퍼를 이용해서 변환효율 19% 대의 HIT 태양전지를 개발한 바 있다. 그 동안 지속적으로 p-형 Si HIT 태양전지를 고효율화하기(< 22%) 위해서 많은 노력이 진행되어 왔지만 이와 같은 노력에도 불구하고 아직 p-형 HIT는 n-형 HIT 태양전지에 비해서 다소 성능면에서 떨어져 있다. 본 연구는 n- 및 p-형 실리콘 웨이퍼로 구성된 HIT 태양전지의 물리적인 차이점에 초점을 맞추고, 결정 및 비정질 실리콘 층의 역할에 대해서 연구하였다. 특히 태양전지 효율을 향상시키는 요소들로서 결정 실리콘의 불순물 준위(n- 및 p-형) 또는 비저항, 비정질 실리콘으로 구성된 emitter 층, intrinsic 층, 경계면이 고려되었다. 그리고 이러한 요소들이 HIT 태양전지에 미치는 영향을 조사하기 위해서 AMPS-1D 컴퓨터 프로그램을 사용하였고, 이를 통해서 HIT 태양전지의 결정 및 비정질 실리콘 층의 역할을 물리적 정량적으로 분석하였다. 본 연구에 적용되는 HIT는 ITO/a-Si:H(p+)/a-Si:H(i)/c-Si(n)/a-Si:H(i)/a-Si:H(n+) 및 ITO/a-Si:H(n+)/a-Si:H(i)/c-Si(p)/a-Si:H(i)/a-Si:H(p+)의 구조로서 다음과 같은 태양전지 특성을 갖는다: n-형 HIT의 경우, fill factor ~ 0.78, 단락전류밀도 ~ 38.1$mA/cm^2$ , 개방전압 0.74 V, 변환효율 22.3 % (그리고 p-형 HIT의 경우, fill factor ~ 0.76, 단락전류밀도 ~ 36.5$mA/cm^2$ , 개방전압 0.69 V, 변환효율 19.4 %). -
The solar energy is dramatically increasing as the alternative energy source and the silicon(Si) solar cell are used the most. In this study, the improved process and equipment for the metallurgical refinement of multicrystalline Si were evaluated for the inexpensive solar cell. The planar plane and columnar dendrite aheadof the liquid-solid interface position caused the superior segregation of impurities from the Si. The solidification rate and thermal gradient determined the shape of dendrite in solidified Si matrix solidified by the directional solidification(DS) method. To simulate this equipment, the commercial software, PROCAST, was used to solve the solidification rate and thermal gradient. Si was vertically solidified by the DS system with Stober process and up-graded metallurgical grade or metallurgical grade Si was used as the feedstock. The inductively coupled plasma mass spectrometry (ICP) was used to measure the concentration of impurities in the refined Si ingot. According to the result of ICP and simulation, the high thermal gradient between the two phases wasable to increase the solidification rate under the identical level of refinement. Also, the separating heating zone equipped with the melting and solidification zone was effective to maintain the high thermal gradient during the solidification.
-
야금학적 방법을 통한 태양전지용 실리콘 제조를 위하여 아크로(Arc furnace)에서 제조된 용융 상태의 금속급 실리콘을 슬래그와 직접 반응시켜 불순물을 제거하는 공정에 관한 연구를 수행하였다. 이를 위해 아크로와 고주파 유도용해로(High-frequency induction furnace)를 이용하여 금속급 실리콘을 제조와 정련 특성 실험을 수행하였다. 본 연구에서 금속급 실리콘을 제조하기 위한 장비로 150kW급-DC 아크로와 300kW급-AC 아크로를 사용하였다. 원재료로 규석, 코크스(Cokes), 숯, 그리고 우드칩(Wood chip)을 실험 비율에 맞춰 아크로 내부에 장입하고, 이를 용융환원 방법을 통해 반응을 시켰다. 이때 생산된 금속급 실리콘의 순도는 약 99.2~99.8% 이었으며, 원재료의 순도, 장입 비율 및 아크로 운전 특성에 따라 편차가 있다. 아크로에서 생산된 금속급 실리콘의 경우 인(phosphorus), 붕소(boron)를 다량 함유하고 있고, 이를 제거하기 위하여 50kW급 고주파 유도용해로 장비를 사용하여 슬래그 정련 실험을 수행하였다. 슬래그 정련시 사용한 성분은 SiO2, CaO 그리고 CaF2 이며, 금속급 실리콘과 슬래그의 질량비 및 반응 시간에 따른 실리콘 불순물 특성을 평가하였다. 실험결과 인과 붕소는 각각 1 ppm 이하, 5 ppm 이하 였으며, 칼슘을 제외한 대부분의 금속 불순물의 경우 0.1~0.2% 임을 확인하였다.
-
The back contact solar cell (BCSC) has several advantages compared to the conventional solar cell since it can reduce grid shadowing loss and contact resistance between the electrode and the silicon substrate. This paper presents the effect of the surface texturing of the silicon BCSC by varying the texturing depth or the texturing gap in the commercially available simulation software, ATHENA and ATLAS of the company SILVACO. The texturing depth was varied from
$5{\mu}m$ to$150{\mu}m$ and the texturing gap was varied from$1{\mu}m$ to$100{\mu}m$ in the simulation. The resulting efficiency of the silicon BCSC was evaluated depending on the texturing condition. The quantum efficiency and the I-V curve of the designed silicon BCSC was also obtained for the analysis since they are closely related with the solar cell efficiency. Other parameters of the simulated silicon BCSC are as follows. The substrate was an n-type silicon, which was doped with phosphorous at$6{\times}10^{15}cm^{-3}$ , and its thickness was$180{\mu}m$ , a typical thickness of commercial solar cell substrate thickness. The back surface field (BSF) was$1{\times}10^{20}\;cm^{-3}$ and the doping concentration of a boron doped emitter was$8.5{\times}10^{19}\;cm^{-3}$ . The pitch of the silicon BCSC was$1250{\mu}m$ and the anti-reflection coating (ARC) SiN thickness was$0.079{\mu}m$ . It was assumed that the texturing was anisotropic etching of crystalline silicon, resulting in texturing angle of 54.7 degrees. The best efficiency was 25.6264% when texturing depth was$50{\mu}m$ with zero texturing gap in case of low texturing depth (<$100{\mu}m$ ). -
PVT(Photovoltaic Thermal) 모듈은 태양광과 태양열 에너지를 동시 이용이 가능한 모듈로서 태양광전지(PV, Photovoltaic)모듈에 열교환기를 접합한 형태로 전기에너지뿐만 아니라 열에너지를 동시에 생산할 수 있는 시스템이다. 기존 PV 모듈은 일사량이 많으면 전력 생산량이 증가하는 동시에 PV모듈의 온도가 상승함에 따라 발전 효율이 감소하는 문제점이 있으며 일반적으로
$25^{\circ}C$ 이상 조건에서 모듈 온도가$10^{\circ}C$ 증가할수록 발전효율의 약 4~5% 정도 감소하는 것으로 보고되고 있다. PVT 모듈은 기존 태양광모듈에 열교환기를 접합하여 냉각함으로써 PV모듈의 온도를 낮추어 발전효율을 증가시키는 동시에 부가적으로 발생하는 온수를 직접이용하거나 다양한 계통의 보조 열원으로 이용할 수 있는 장점이 있다. 본 연구에서는 수치해석기법(CFD)을 활용하여 PV모듈 냉각 및 온수 발생을 위한 열교환기를 설계하였으며 다양한 형상의 열교환기에 대해 유동해석을 수행하여 최적의 열흡수효율을 갖는 열교환기의 형상을 설계하였다. 또한 최적 설계된 PVT 모듈을 제작하여 실제 태양과 유사한 광원을 갖는 인공태양조건에서의 실내 실험을 통해 PVT 모듈의 성능을 검증하였으며 또한 실제 노상에 설치하여 ASHRAE 93-77의 실험기준과 ECN의 PVT 집열기 성능측정 가이드라인에 따라 옥외 시험평가를 하여 PVT 모듈의 성능 검증을 하였다. 최적 설계된 PVT모듈에 대한 성능평가 결과 기존 PV 모듈보다 발전효율이 약 15%(기존 발전효율 대비) 향상된 결과를 확인하였다. -
PEMS (printed electro-mechanical system) is fabricated by means of various printing technologies. Passive and active compo-nents in 2D or 3D such as conducting lines, resistors, capacitors, inductors and TFT(Thin Film Transistor), which are printed withfunctional materials, can be classified in this category. And the issue of PEMS is applied to a R2R process in the manu-facturing process. In many electro-devices, the vacuum process is used as the manufacturing process. However, the vacuum process has a problem, it is difficult to apply to a continuous process such as a R2R(roll to roll) printing process. In this paper, we propose an ESD (electro static deposition) printing process has been used to apply an organic solar cell of thin film forming. ESD is a method of liquid atomization by electrical forces, an electrostatic atomizer sprays micro-drops from the solution injected into the capillary with electrostatic force generated by electric potential of about several tens kV. ESD method is usable in the thin film coating process of organic materials and continuous process as a R2R manufacturing process. Therefore, we experiment the thin films forming of PEDOT:PSS layer and active layer which consist of the P3HT:PCBM. The organic solar cell based on a P3HT/PCBM active layer and a PEDOT:PSS electron blocking layer prepared from ESD method shows solar-to-electrical conversion efficiency of 1.42% at AM 1.5G 1sun light illumination, while 1.86% efficiency is observed when the ESD deposition of P3HT/PCBM is performed on a spin-coated PEDOT:PSS layer.
-
Gang, In-Gu;Kim, Hyeok-Jong;Kim, Do-Hyeong;Kim, Jin-Sik;Kim, Hyo-Jae;Won, Su-Hyeon;Jo, Seong-Hun;Lee, Sang-Gwon;Ha, Jeong-Won;Choe, Byeong-Ho 113.2
Sn-Ag계 합금은 대표적인 무연 솔더 조성으로 전자제품의 실장 및 접합에 적용되어 왔으며, 태양전지 분야에서도 모듈의 전극과 bus바로 사용되는 등 다양한 분야에서 사용되고 있다. 그러나 최근 Ag 가격의 급격한 상승과 솔더 접합부의 신뢰성을 보다 향상시키고자 Ag의 함량을 줄이고 다원계 합금 조성의 무연 솔더 연구가 활발히 진행되고 있다. 본 실험에서는 기존의 연구 결과를 바탕으로 Sn-1.0Ag-0.5Cu-0.4In 4원계 무연솔더 조성에 Bi를 첨가하여 최적의 융점과 용융구간을 가지는 5원계 Sn-Ag-Cu-In-Bi 계 솔더 합금을 설계하였다. 이 설계된 합금은 기존의 유연 솔더인 Sn-Pb와 대표적인 무연 솔더인 Sn-3.5Ag와 각각의 특성을 비교 분석하였다. 젖음성을 평가하기 위하여 wetting balance tester를 이용하여 실험을 행하였고 Differential Scanning Calorimetry(DSC)를 분석하여 젖음 정도와 조성 분석 및 고상점과 액상점 등의 녹음 거동을 확인하였다. 또한 각각의 조성별 전단응력에 따른 파괴 거동을 분석하였다. -
Electrical sintering of the front electrode for crystalline silicon solar cells was performed applying a constant DC current to the printed lines. Conducting lines were printed on glass substrate by a drop-on-demand (DOD) inkjet printer and silver nanoparticle ink. Specific resistance and microstructure of sintered silver lines and were measured with varying DC current. To find the relation between temperature increase with changing applied current and specific resistance, temperature elevation was also calculated. Sintering process finished within a few milliseconds. Increasing applied DC current, specific resistance decreased and grain size increased after sintering. Achieved minimum specific resistance is approximately 1.7 times higher than specific resistance of the bulk silver.
-
비정질 실리콘 박막 태양전지연구에 일반적으로 사용되고 있는 ASA (Advanced Semicon ductor Analysis) simulation을 이용하여 TCO/p에 삽입될 버퍼층의 최적 구조를 설계해보았다. 기본적인 p,i,n층 단일막 data 값을 고정시켜 버퍼층의 광학적 밴드갭을 1.75~1.95eV, 활성화 에너지를 0.3~0.4eV, 두께를 5~15nm로 가변해 보았다. 첫 번째로 동일한 활성화 에너지를 갖는 버퍼층의 광학적 밴드갭을 증가 시켰을 경우 built-in potential이 증가하였으며 이는 개방전압의 증가로 이어졌다. 두 번째로 활성화 에너지가 작은 경우 큰 경우에 비하여 Conduction-band와 Fermi-level의 차이가 증가 하게 되어 활성화 에너지가 큰 경우에 비해 높은 built-in potential을 얻을 수 있었다. 또한 버퍼층과 p층의 접합부분에서의 barrier가 활성화 에너지의 차이를 줄일수록 감소 함 을 알 수 있었다. 장벽의 감소로 정공의 흐름을 방해하는 요소가 줄어들었고 효율도 증가하였다. 마지막으로 버퍼층 두께가 두꺼워 질수록 박막 내에서 빛 흡수가 많아지게 되어 광 흡수층으로 가야할 빛의 양이 줄어들게 되어 단락전류값이 감소하는 것을 알 수 있었다. Simulation결과 버퍼층의 광학적 밴드갭이 1.95eV로 크고 활성화 에너지가 0.3eV이하로 p층에 비하여 낮으며 두께가 5nm로 얇을수록 좋다는 결과를 알 수 있었다.
-
최근 기본적인 pin 구조의 박막 cell 에서 i layer를 최적화 시키는 방안으로 double layer 구조가 많이 연구되고 있다. 본 연구에서는 ASA(Advanced Semicon ductor Analysis) simulation을 이용하여 i-double layer 최적화에 대한 연구를 진행해 보았다. 두께 150/150nm의 i double layer의 band gap 가변을 한 simulation 결과를 보았을 때, p쪽의 band gap이 상승하면서 intrinsic layer 내의 field가 증가하여 recombination center가 감소하였으나 FF의 감소가 있었다. n쪽의 band gap을 상승 시켰을때 n/i 쪽 field 증가로 Voc가 상승되어 초기 효율이 증가하였으나 intrinsic layer내의 field가 감소하여 recombination center가 오히려 증가하였다. 결과적으로 electric field와 효율을 동시에 고려했을 때 두께 300nm, 1.75의 band gap을 가지는 single layer 보다 150/150nm두께에 1.8/1.7 또는 1.8/1.75의 bandgap을 가지는 double layer를 사용하였을 때 보다 높은 효율을 얻을 수 있었다.
-
실리콘 박막 태양전지는 기판의 표면형상에 따라 셀 내부에서 이동하는 빛의 광학적인 경로가 크게 증가하여 변환효율의 향상을 기대할 수 있다. 금속 기판은 다양한 표면형상으로 가공이 용이하고 강도와 인성이 우수하며 가격이 저렴하여 실리콘 박막 태양전지의 기판재로 활발한 연구가 진행되고 있다. 본 연구에서는 금속 기판의 표면형상이 반사특성에 미치는 영향을 알아보고자 하였다. 금속 기판재의 표면형상은 기계적 연마 방식을 응용하여 다양하게 제작하였다. 반사특성을 보기 위하여 UV-visible spectrometer를 사용하여 총 반사율과 산란 반사율을 측정하였고, 표면 형상에 따른 Fe-Ni 기판과 Ag 후면반사막의 반사 특성이 태양전지 셀 내부의 광포획의 증가에 어떠한 영향을 주는지 비교 분석하였다.
-
Materials with a combination of high electrical conductivity and optical transparency are important components of many electronic and optoelectronic devices such as liquid crystal displays, solar cells, and light emitting diodes. In this study, to fabricate a low-resistance and high optical transparent electrode film for organic photovoltaic, the following steps were performed: the design and manufacture of an electroforming stamp mold, the fabrication of thermal roll imprinted (TRI) poly-carbonate (PC) patterned films, the manufacture of high-conductivity and low-resistance Ag paste which was filled into patterned PC film using a doctor blade process and then coated with a thin film layer of conductive polymer by a spin coating process. As a result of these imprinting processes the PC films obtained a line width of
$10{\pm}0.5{\mu}m$ , a channel length of$500{\pm}2{\mu}m$ , and a pattern depth of$7.34{\pm}0.5{\mu}m$ . After the Ag paste was used to fill part of the patterned film with conductive polymer coating, the following parameters were obtained: a sheet resistance of$9.65{\Omega}$ /sq, optical transparency values were 83.69 % at a wavelength of 550 nm. -
연성 CIGS 태양전지를 제작하기 위해서는 휘어지는 연성 기판재의 적용이 반드시 필요하다. 상용되는 연성 기판재로는 플라스틱, 폴리이미드, 금속재가 있다. 그러나 플라스틱과 폴리이미드는 고효율의 CIGS 흡수층을 제조하기 위한
$500{\sim}600^{\circ}C$ 의 공정에 접합하지 못하다. 금속 기판재의 경우는 몰리브데늄, 알루미늄, 티타늄, 크롬강, 스테인레스강, 합금재 등이 있다. 이러한 금속 기판재 중에서 Fe-Ni 합금재는 Ni 함량의 변화에 따라 기계적, 자기적, 열팽창 특성이 다르게 나타나는 것으로 알려져 있다. 선행 연구에서 CIGS 태양전지의 기판재로 열팽창 계수가 박막층과 유사한 SUS400번 계열과 Fe-52Ni이 적합하다는 것을 확인 하였다. 따라서 본 연구에서는 유한요소해석(Finite element analysis) 프로그램인 Algor를 이용하여 CIGS solar cell을 설계하고 Fe-52Ni 기판재와 절연층인 SiO2, 흡수층인 CIGS의 두께에 따른 Cell의 잔류응력을 해석하였다. -
We have demonstrated Forst-type resonance energy transfer (FRET) in the quasi-solid type dye-sensitized solar cells between organic fluorescence materials as an energy donor doped in polymeric gel electrolyte and ruthenium complex as an energy acceptor on surface of
$TiO_2$ . The strong spectral overlap of emission/absorption of energy donor and acceptor is required to get high FRET efficiency. The judicious choice of energy donor allows the enhancement of light harvesting characters of energy acceptor in quasi-solid dye sensitized solar cells which increase the power conversion efficiency. The enhanced light harvesting effect by the judicious choice/design of the fluorescence materials and sensitizing dyes permits the enhancement of photovoltaic performance of DSSC. -
Since Gratzel and co-workers developed a new type of solar cell based on the nanocrystalline TiO2 electrode, dye-sensitized solar cells (DSSCs) have attracted considerable attention on account of their high solar energy-to-conversion efficiencies (11%), their easy manufacturing process with low cost production compared to conventional p-n junction solar cells. The mechanism of DSSC is based on the injection of electrons from the photoexcited dye into the conduction band of nanocrystalline TiO2. The oxidized dye is reduced by the hole injection process from either the hole counter or electrolyte. Thus, the electronic structures, such as HOMO, LUMO, and HOMO-LUMO gap, of dye molecule in DSSC are deeply related to the electron transfer by photoexcitation and redox potential. To date, high performance and good stability of DSSC based on Ru-dyes as a photosensitizer had been widely addressed in the literatures. DSSC with Ru-bipyridyl complexes (N3 and N719), and the black ruthenium dye have achieved power conversion efficiencies up to 11.2% and 10.4%, respectively. However, the Ru-dyes are facing the problem of manufacturing costs and environmental issues. In order to obtain even cheaper photosensitizers for DSSC, metal-free organic photosensitizers are strongly desired. Metal-free organic dyes offer superior molar extinction coefficients, low cost, and a diversity of molecular structures, compared to conventional Ru-dyes. Recently, novel photosensitizers such as coumarin, merocyanine, cyanine, indoline, hemicyanine, triphenylamine, dialkylaniline, bis(dimethylfluorenyl)-aminophenyl, phenothiazine, tetrahydroquinoline, and carbazole based dyes have achieved solar-to-electrical power conversion efficiencies up to 5-9%. On the other hand, organic dye molecules have large
${\pi}$ -conjugated planner structures which would bring out strong molecular stacking in their solid-state and poor solubility in their media. It was well known that the molecular stacking of organic dyes could reduce the electron transfer pathway in opto-electronic devices, significantly. In this paper, we have studied on synthesis and characterization of dendritic organic dyes with different number of electron acceptor/anchoring moieties in the end of dendrimer. The photovoltaic performances and the incident photon-to-current (IPCE) of these dyes were measured to evaluate the effects of the dendritic strucuture on the open-circuit voltage and the short-circuit current. -
The dye-sensitized solar cell (DSSC) is a device for the conversion of visible light into electricity, based on the sensitization of wide bandgap semiconductors. The performance of the cell mainly depends on a dye used as sensitizer. The absorption spectrum of the dye and the anchorage of the dye to the surface of TiO2 are important parameters determining the efficiency of the cell. Generally, transition metal coordination compounds(ruthenium polypyridyl complexes) are used as the effective sensitizers, due to their intense charge-transfer absorption in the whole visible range and highly efficient metal-to ligand charge transfer. However, ruthenium polypyridyl complexes contain a heavy metal, which is undesirable from point of view of the environmental aspects. Moreover, the process to synthesize the complexes is complicated and costly. Alternatively, organic dyes can be used for the same purpose with an acceptable efficiency. The advantages of organic dyes include their availability and low cost. We designed and synthesized a series of organic sensitizers containing long wavelength absorption-chromophores for the dye sensitized solar cell. The DSSC composed of Blue-chromophores for the sensitization absorbed long wavelength region which is different also applied into the dye-cocktail (mixing) system. The photovoltaic property of DSSCs organic long wavelength absorption-chromophores were measured and evaluated by comparison with that of individual chromophores.
-
In order to increase the energy conversion efficiency of dye-sensitized solar cells (DSSCs), we employed a counter electrode that was platinum coated using a doctor blade technique on synthesized ZnO nanostructures on fluorinedoped tin oxide (FTO). The ZnO nanostructures possessing high electrochemical activity and large surface area of the counter electrode were grown by a chemical bath deposition (CBD) method at various times, 2, 4, and 8 h. The efficiency of DSSC with the Pt-ZnO counter electrode was improved 7.01% (grown for 2 h), 7.63% (grown for 4 h), and 6.13% (grown for 8 h), respectively. Compared with a standard DSSC without ZnO nanostructures, whose efficiency was 6.27%, the energy conversion efficiency increased approximately 22% for the DSSC with the Pt-ZnO (grown for 4 h) electrode. It indicates that the Pt coated on the ZnO nanostructure improves the electrocatalytic activity of the counter electrode.
-
Since Gratzel et al. reported the first efficient dye-sensitized solar cells(DSSCs) in 1991, they have attracted much attention due to their relatively high power conversion efficiency and potentially low cost production. To date, high performance and good stability of DSSC based on Ru-dyes as a photosensitizer had been widely addressed in the literatures. However, the Ru-dyes are facing the problem of manufacturing costs and environmental issues. In order to obtain even cheaper photosensitizers for DSSC, the metal-free organic photosensitizers are strongly desired. The metal-free organic dyes offer superior molar extinction coefficients, low cost, and diverse molecular structures as compared to the conventional Ru-dyes, In this work, we have studied on the synthesis and characterization of the organo dendritic dyes containing different number of electron acceptor moieties in a molecule.
-
Dye-sensitized solar cells (DSSC) are currently attracting wide spread academic and commercial interest for the conversion of sunlight into electricity because of their easy manufacturing process and high efficiency. The solar energy conversion efficiencies of DSSC are strongly dependent on dye molecules adsorbed on the TiO2 surface which used for photosensitization of sun light, since an excited state of dye could inject an electron into the conduction band of semiconductor. We have developed novel organic dyes which have phenothiazine moieties as an electron donor in their charge-transfer chromophore for application of DSSCs. We had synthesized a series of phenothiazine derivatives which have different wave length absorbing chromophore in the molecule with high molar extinction coefficient. The photovoltaic performance of DSSC composed of organic chromophores with broad wavelength absorption property were measured and evaluated by comparison with that of pristine ruthenium dye.
-
Increase the efficiency of PV modules for high-efficiency solar cells, light transmittance improvements, increasing the module, and much more research and development. Dual we light transmittance for photovoltaic module materials in low iron tempered glass in SiO2 using liquid AR implementation, light transmittance to solar modules to increase the efficiency of research.
-
The improvement of solar energy-to-electricity conversion efficiency has continued to be an important research area of dye-sensitized solar cells (DSSCs). The mechanism of DSSCs is based on the injection of electrons from the photoexcited dye into the conduction band of nanocrystalline TiO2 or ZnO. Thus, the electronic structures, such as HOMO, LUMO, and HOMO-LUMO band gaps of dye moleculed in DSSC are deeply related to the electron transfer by photoexcitation and redox potential. Organic dyes, because of their many advantages, such as high molar extinction coefficients, convenience of customized molecular design for desired photophysical and photochemical properties, inexpensiveness with no transition metals contained, and environment-friendliness, are suitable as photosensitizers for DSSC. We believe that practically useful organic dye photosensitizers can be produced by exploiting electron donor/acceptor system with proper length of
${\pi}$ -conjugation in a chromophore to control the absorption wavelength and enhance the photovoltaic performance. In this research, We designed and synthesized organic dyes also investigated the photoelectrochemical properties of a series of ionic dyes in DSSCs. -
Bae, Soohyun;Park, Sungeun;Kim, Young Do;Park, Hyomin;Kim, Soo Min;Kim, Seongtak;Kim, Hyunho;Tark, Sung Ju;Kim, Dongwhan 121.1
현재 상용화되고 있는 단결정 실리콘 태양전지는 알루미늄 페이스트를 이용하여 후면의 전 영역에 전계를 형성한다. 최근에는 고효율을 얻기 위하여 후면에 패시베이션 효과와 장파장에 대한 반사도를 증가 시키는 SiNx막을 증착 후, 국부적으로 전계를 형성하는 국부 후면 전극(Local back surface field)기술이 연구되고 있다. 본 연구에서는 전면만 텍스쳐 된 단결정 실리콘 웨이퍼를 이용하였다. Plasma Enhanced Chemical Vapor Deposition(PECVD)를 이용하여 전,후면에 SiNx를 증착 하였고 후면의 국부적인 전극 패턴 형성을 위하여 SiNx 식각용 페이스트를 사용한 스크린 프린팅 기술을 이용하였다. 스크린 프린팅을 이용하여 패턴이 형성된 후면에 알루미늄을 인쇄 한 후 Rapid Thermal Process(RTP)를 이용하여 소성 공정 조건을 변화시켰다. 소성 조건 동안 형성되는 후면 전계층은 peak 온도와 승온속도, 냉각 속도에 따라 형상이나 특성이 변화하기 때문에 소성 조건을 변화시키며 국부적 후면 전계 형성의 최적화에 관한 연구를 수행하였다. 패이스트를 이용하여 SiNx를 식각 후 광학 현미경(Optical Microscopy)을 사용하여 SiNx의 식각 유무를 살펴보았고, RTP로 형성된 국부 전계층의 형성 두께, 주변 부분의 형상을 살피기 위해 도핑 영역을 혼합수용액으로 식각하여 주사 전자 현미경(SEM)을 이용하여 관찰 하였다. 또한 후면의 특성을 살펴보기 위해 분광 광도계(UV/VIS/NIR Spectrophotometer)를 사용하여 후면 SiNx층의 유무에 따른 반사도를 비교, 측정 하였다. -
Aluminum-doped Zinc Oxide (AZO) is considered as an excellent candidate to replace Indium Tin Oxide (ITO), which is widely used as transparent conductive oxide (TCO) for electronic devices such as liquid crystal displays (LCDs), organic light emitting diodes (OLEDs) and organic solar cells (OSCs). In the present study, AZO thin film was applied to the transparent electrode of a channel-shaped flexible organic solar cell using a low-temperature selective-area atomic layer deposition (ALD) process. AZO thin films were deposited on Poly-Ethylene-Naphthalate (PEN) substrates with Di-Ethyl-Zinc (DEZ) and Tri-Methyl-Aluminum (TMA) as precursors and
$H_2O$ as an oxidant for the atomic layer deposition at the deposition temperature of$130^{\circ}C$ . The pulse time of TMA, DEZ and$H_2O$ , and purge time were 0.1 second and 20 second, respectively. The electrical and optical properties of the AZO films were characterized as a function of film thickness. The 300 nm-thick AZO film grown on a PEN substrate exhibited sheet resistance of$87{\Omega}$ /square and optical transmittance of 84.3% at a wavelength between 400 and 800 nm. -
Boo, Hyun Pil;Kang, Min Gu;Lee, KyungDong;Lee, Jong-Han;Tark, Sung Ju;Kim, Young Do;Park, Sungeun;Kim, Dongwhan 122.1
Phosphorus is known to pile-up at the silicon surface when it is thermally oxidized. A thin layer, about 40nm thick from the silicon surface, is created containing more phosphorus than the bulk of the emitter. This layer has a gaussian profile with the peak at the surface of the silicon. In this study the pile-up effect was studied if this layer can act as a front surface field for solar cells. The effect was also tested if its high dose of phosphorus at the silicon surface can lower the contact resistance with the front metal contact. P-type wafers were first doped with phosphorus to create an n-type emitter. The doping was done using either a furnace or ion implantation. The wafers were then oxidized using dry thermal oxidation. The effect of the pile-up as a front surface field was checked by measuring the minority carrier lifetime using a QSSPC. The contact resistance of the wafers were also measured to see if the pile-up effect can lower the series resistance. -
결정질 태양전지 제작에서, passavtion은 표면의 반사도를 줄여주는 반사 방지막의 역할과 표면의 dangling bond를 감소시켜, 표면 재결합 속도를 줄이고 minority carrier lifetime을 증가하는 데 큰 영향을 미친다. 그렇기 때문에 저가형 고효율 태양전지 제작에서 우수한 특성을 가지는 passivation막은 매우 중요한 이슈이다. 본 연구에서는 LBC(local back contact) 구조를 가지는 단결정 태양전지 후면에, 기존의 Full Al-BSF의 passivation 막을 SiNx와 ONO passivation 막으로 각각 대체하여, LBC 구조에서 더 적합한 passivation 막을 찾고자 하였다. SiNx와 ONO passivation 막은 단결정 LBC 구조 태양전지 후면에 각각 형성되었고
$800^{\circ}C$ , 20 sec 조건으로 소성되었다. 실험결과는 minority carrier lifetime과 surface recombination velocity로 관찰하였다. 그 결과, SiNx passivation 막의 표면 재결합 속도는 29.7cm/s이고, ONO passivation 막의 표면 재결합 속도는 24.5cm/s로, Full Al-BSF 표면 재결합 속도 750cm/s에 비해 더 적합한 passivation 막으로 확인할 수 있었다. 결과적으로 SiNx,ONO passivation 막이 Full Al-BSF보다 전극에 수집되는 캐리어의 양이 많아짐에 따라 효율향상을 가져올 수 있을 것이다. -
기존의 p-type 태양전지 공정과 유사한 공정으로 제작되는 n-type
$ALU^+$ 태양전지는 후면에 Al을 screen printing하여 emitter층을 형성한 구조이다. screen printing은 공정의 단순화와 제조 단가의 저비용으로 인해, metalization 공정에서 많이 쓰이고 있다. 본 연구에서는 양산 가능한 n-type$ALU^+$ 태양전지 제작을 위해, 후면 Al emitter 층을 single, dobule, triple로 변경하며 Al의 양을 가변하였고, 그에 따른 특성의 변화를 연구하였다. screen printing 횟수가 변경된 후면 Al emitter 층의 특성은 DIV와 LIV 측정을 통해 분석하였다. 실험 결과 Al을 single printing 하였을 때보다, double, triple printing을 통하여 Al의 양을 증가하였을 때, DIV 데이터에서 직렬저항(Rs)가$24.44{\Omega}/cm^2$ 에서$0.31{\Omega}/cm^2$ 으로 감소하였고, 단락전류(Jsc)는 1.26mA/$cm^2$ 에서 37.7mA/$cm^2$ 으로 약 300% 증가한 것을 확인할 수 있었다. 프린팅 횟수에 따른 LIV 데이터의 Fill Factor를 분석하게 되면, double printing이 64.35%로 54.75%의 triple printing보다 약 1.17배 더 향상된 것으로 확인하였다. 이러한 결과를 바탕으로 후면 Al emitter 형성시에 Al의 양이 적절하지 못한 이유로, Al emitter가 제대로 형성되지 못하거나 과하게 형성되면, 태양전지 내부에 누설 저항의 변화와 누설 전류의 증가로 인해, 단락전류(Jsc)와 Fill Factor 감소의 주요 원인이 된다는 것을 확인할 수 있었다. -
$ALU^+$ 태양전지는 PN접합을 후면에서 즉, Al을 소성하여 형성시키기 때문에 얼마나 균일하고 두껍게 형성하는 것이 가장 중요하다. 소성(Firing)은 태양전지 제조 과정에서 후면의 접촉을 위한 중요한 공정이다. 본 연구에서는 상업화가 가능한 n-type$ALU^+$ Emitter 태양전지에서 소성 횟수에 따른 특성을 연구 하였다.$ALU^+$ emitter 형성의 최적화를 위해 소성온도를 가변하고, 최적화된 온도에서 소성 횟수에 따른 DIV 측정을 통해 셀을 분석 하였다. 소성 횟수는 1~3회로 하였고, 그 결과 단락전류 밀도(Jsc)가 33.57mA/$cm^2$ 로 처음보다 15.1%증가 하였고, 곡선인자(Fill Factor)는 3회에서 66.04%로 218%증가 하였다. Al을 짧은 시간 안에 소성을 시키므로 해서 후면의$P^+$ Emitter가 균일하게 형성되었기 때문에 개방전압(Voc)의 증가를 확인하였다. 본 연구를 통해$ALU^+$ 태양전지의 후면 Aluminium 소성 조건의 최적화를 통하여$ALU^+$ emitter가 충분히 형성되지 못하면 누설전류가 발생되고 직렬저항(Rs)이 크게 증가하여 개방전압(Voc) 및 단락전류밀도(Jsc)의 감소가 발생하게 되고, 직렬저항(Rs)의 증가와 병렬저항(Rsh)의 감소는 Fill Factor의 급격한 감소를 초래하게 됨을 알 수 있다. 이를 개선하면 태양전지 효율을 상승시키는 결과를 얻을 수 있음을 확인하였다. -
결정질 태양전지에서 도핑(Doping)은 반도체(Semiconductor)의 PN 접합(Junction)을 형성하는 중요한 역할을 한다. 도핑은 반도체에 불순물(Dopant)을 주입하는 공정으로 고온에서 진행되며 온도는 중요한 변수(Parameter)로 작용한다. 본 연구에서는 여러 가지 도핑 방법 중 SOD(Spin-On Dopant)를 이용하여 온도에 따른 도핑 결과와 특성을 분석 하였다. P-type 웨이퍼(Wafer)에 SOD를 이용하여 불순물을 증착 후 Hot-plate에서 15분간 Baking 하였다. Baking된 웨이퍼는 노(Furnace)에 넣고
$860^{\circ}C{\sim}880^{\circ}C$ 까지$10^{\circ}C$ 씩 가변하였다. 각각의 조건에 대해 Lifetime과 Sheet Resistance을 측정하였고, 그 결과$880^{\circ}C$ 에서의 Lifetime이$23.58{\mu}s$ 로$860^{\circ}C$ 에 비해 235.8% 증가하여 가장 우수 하였으며, Sheet Resistance 또한$68{\Omega}$ /sq로$860^{\circ}C$ 에서 가장 우수하게 측정되었다. SOD의 속도 가변에 따른 특성 변화를 보기 위해 온도는$880^{\circ}C$ 에 고정한 후 속도를 3000rpm~4500rpm까지 500rpm간격으로 1시간동안 실험한 결과 rpm 속도에 따른 lifetime 변화는 거의 없었으며, Sheet Resistance는 3000rpm에서$63{\Omega}$ /sq로 가장 우수 하였다. 본 연구를 통해 온도와 Spin rpm에 따른 특성을 확인한 결과 온도가 높을 때 Sheet Resistance가 가장 안정화 되며, lifetime이 더욱 우수한 것을 확인할 수 있었다. -
현재 박막형 태양전지는 실리콘계가 주류를 이루고 있으며, 유리기판 또는 유연성 기판에 비정질 실리콘 박막을 형성시킨 태양전지와 실리콘 기판 양면에 태양전지를 형성하는 방법 등 효율을 극대화시킨 이종접합 태양전지 등이 연구되고 있다. 예컨대 밴드갭이 서로 다른 박막들 간의 이종접합을 이용한 tandem 구조 및 triple 구조의 Si 박막 태양전지의 경우 13%대 변환효율을 나타낸다고 보고된 바 있다. 본 연구에서는 비정질 Si 박막 태양전지 내 흡수층의 효율을 최대화하기 위하여 AZO/Ag 이중구조 박막의 특성에 관한 연구를 수행하고자 한다. combinatorial sputtering system을 이용하여 AZO/Ag 이중구조 박막을 제작하였으며 타겟으로는 4-inch target(Ag, 2wt% Al2O3 doped ZnO)이 사용되었다. 유리기판 상에 combinatorial sputter system으로 상온에서 제작된 Ag 박막의 두께는 25nm로 성장시켰으며 연속공정으로 AZO 박막을 제작하였고, AZO 박막은 100~500nm의 두께경사를 나타내었다. 이 때 유리기판상에 성장된 Ag/AZO 박막의 면저항은 약
$2{\Omega}/{\Box}$ 값을 나타내었다. 본 발표에서는 AZO/Ag 이중 구조 박막의 우수한 전기적 특성을 기반으로 표면 거칠기 및 반사도 특성 등에 관하여 추가적으로 토론한다. -
빛 에너지를 전기에너지로 변환하는 발전소자인 태양전지는 청정 재생 에너지원으로 최근 Si 박막 태양전지의 고 효율화를 위해 여러 기술적인 면에서 개발되어지고 있다. 현재 박막형 태양전지는 실리콘계가 주류를 이루고 있으며, 유리 혹은 유연성기판(금속 or 고분자)에 비정질 실리콘 박막을 형성시킨 태양전지와 실리콘웨이퍼의 양면에 태양전지를 형성함으로써 효율을 극대화시킨 이종접합태양전지 등이 연구되고 있다. 특히 flexible 태양전지는 hard 기판에 비해 비교적 저가인 플라스틱 필름과 금속 foil을 기판으로 이용함으로서 저가화가 용이하며, 가볍고 유연성을 갖추고 있어 휴대와 시공에 있어 매우 우수한 장점을 가지고 있다. 본 연구에서는 flexible 기판(stainless steel)을 이용하여 태양전지 내 반사막 층이 미치는 영향을 알아보기 위하여 AZO/Ag 이중구조 박막의 특성을 연구하였다. RF magnetron sputtering system을 이용하였으며, 상온에서 Ag/AZO 이중구조 박막을 제조하였다. stainless steel 기판 위에 Ag층을 25nm 두께로 증착하였으며 연속공정으로 AZO 박막을 100~500nm의 두께경사를 가지도록 성장시켰다. 이 때의 AZO/Ag 이중구조 박막의 표면 morphology는 AFM 분석결과 7nm~3nm의 값을 나타내었으며, AZO 박막의 두께가 증가할수록 rms 값이 감소하는 경향을 보여주었다. 본 발표에서는 flexible 기판 상에 성장된 AZO/Ag 이중구조 박막의 전기적, 광학적 특성 등에 관하여 추가적으로 토론한 후 태양전지 효율 중 흡수층 내 반사막 층이 미치는 역할을 알아보겠다.
-
CuInGaSe2 (CIGS)을 포함한 Chalcopyrite계 물질은 직접천이형 반도체이면서,
${\sim}1{\times}10^5cm^{-1}$ 이상의 광흡수계수를 보이며, 조성제어를 통한 밴드갭 조절이 가능해 차세대 고효율 박막태양전지재료로 매우 주목받고 있다. 최근, CIGS 박막태양전지 제조를 위해 CIGS 흡수층의 여러 가지 박막제조 공정들이 개발되고 있으나, 동시증착법과 소위 2단계법이라 일컬어지는 금속 전구체 스퍼터링 증착 후 셀렌화 공정을 가장 대표적인 공정이라 말 할 수 있다. 동시증착법은 실험실 수준의 소면적 셀에서 20%에 가까운 높은 효율의 CIGS 박막태양전지 제조에 성공하였음에도 불구하고, 상용화를 위한 대면적 셀 제조를 위해 해결해야 할 문제들이 아직 남아있다. 또한, 2단계법의 경우는 스퍼터링 공정을 기반으로 대면적 셀 제조에는 용이하나, CIGS/Mo 계면에서의 Ga 응집현상의 발생 및 셀렌화 공정에 사용되는 독성가스($H_2Se$ )의 문제 등이 남아 있어 새로운 시각에서의 접근 방법이 요구되고 있다. 본 연구에서는 CIGS 4성분계 단일 타겟을 사용, RF 스퍼터링 공정을 통해$200{\times}200mm^2$ 기판 위에 CIGS 박막을 제조하여 그 특성을 분석하였다. XRD 분석결과, 동시증착법에서 일반적으로 관찰되는 CIGS/Mo 계면에서의$MoSe_2$ 상의 존재는 관찰되지 않았으며, CIGS 단일상의 다결정 박막이 제조되었음을 알 수 있었다. 또한, CIGS 박막제조 후, RTA 공정을 통해 CIGS 박막의 결정성이 향상됨을 관찰 할 수 있었으며, SIMS 분석결과, Mo층의 공정 조건에 따라 CIGS/Mo 계면에서의 금속원소 (In, Ga, Mo)의 상호확산이 크게 억제됨을 알 수 있었다. 그 외의 특성평가 결과들을 통하여 CIGS 4성분계 단일 타겟을 사용한 CIGS 박막태양전지 제조의 유용성에 대해 논의하고자 한다. -
박막형 태양전지의 효율 향상을 위하여 광확산 패턴이 형성된 기판을 제작하고 이를 이용하여 비정질 실리콘 박막 태양전지를 제작하였다. 나노 임프린트 방법을 사용하여 제작된 광확산 패턴은 불규칙한 마이크로-나노 크기의 미세구조를 가지고 있어 빛의 확산투과 비율을 향상시켜주는 역할을 하였다. 제작된 광확산 기판위에 TCO물질을 증착하고, PECVD법을 사용하여 비정질 실리콘 p-i-n 접합 구조를 형성하였다. 제작된 태양전지 소자를 1.5 AM의 조건에서 I-V 특성을 분석하였으며, 비교군으로 사용된 일본 Asahi 사의 U-type glass에 비해 높은 Jsc 값을 나타내었다. 또한 외부양자효율을 측정함으로써 광확산 패턴에 의한 양자효율 변화를 확인 할 수 있었다.
-
Yang, Hyeon-Hun;Kim, Han-Wool;Han, Chang-Jun;So, Soon-Youl;Park, Gye-Choon;Lee, Jin;Chung, Hea-Deok;Lee, Suk-Ho;Back, Su-Ung;Na, Kil-Ju;Jeong, Woon-Jo 126.2
ZnS thin films were deposited with the radio frequency magnetron sputtering technique at various temperatures and sputtering powers. With the increase in the deposition temperature and the decrease in the radio frequency sputtering power, the crystallinity was increased and the surface roughness was decreased, which lead to the decrease in the electrical resistivity of the film. It is also clearly observed that, the intensity of the (111) XRD peak increases with increasing the substrate temperature. On the other hand, as seen in the FWHM decreased with increasing the substrate temperature. Since the FWHM of the (111) diffraction peak is inversely properties to the grain size of the film, then grain size of ZnS thin film increases with increasing the substrate temperature. The electrical resistivity and optical transmittance of the ZnS film as a function of the post-annealing temperature. It can be seen that with the annealing temperature set at$400^{\circ}C$ , the resistivity decreases to a minimum value of$2.1{\times}10^{-3}\;{\Omega}cm$ and the transmittance increases to a maximum value of 80% of the ZnS film. -
Yang, Hyeon-Hun;Kim, Han-Wool;Han, Chang-Jun;So, Soon-Youl;Park, Gye-Choon;Lee, Jin;Chung, Hea-Deok;Lee, Suk-Ho;Back, Su-Ung;Na, Kil-Ju;Jeong, Woon-Jo 127.1
In this paper, ZnO:Al thin films with c-axis preferred orientation were prepared on Soda lime glass substrates by RF magnetron sputtering technique. AZO thin film were prepared in order to clarify optimum conditions for growth of the thin film depending upon process, and then by changing a number of deposition conditions and substrate temperature conditions variously, structural and electrical characteristics were measured. For the manufacture of the AZO were vapor-deposited in the named order. It is well-known that post-annealing is an important method to improve crystal quality. For the annealing process, the dislocation nd other defects arise in the material and adsorption/decomposition occurs. The XRD patterns of the AZO films deposited with grey theory prediction design, annealed in a vacuum ambient($2.0{\times}10-3$ Torr)at temperatures of 200, 300, 400 and$500^{\circ}C$ for a period of 30min. The diffraction patterns of all the films show the AZO films had a hexagonal wurtzite structure with a preferential orientation along the c-axis perpendicular to the substrate surface. As can be seen, the (002)peak intensities of the AZO films became more intense and sharper when the annealing temperature increased. On the other hand, When the annealing temperature was$500^{\circ}C$ the peak intensity decreased. The surface morphologies and surface toughness of films were examined by atomic force microscopy(AFM, XE-100, PSIA). Electrical resistivity, Gall mobility and carrier concentration were measured by Hall effect measuring system (HL5500PC, Accent optical Technology, USA). The optical absorption spectra of films in the ultraviolet-visibleinfrared( UV-Vis-IR) region were recorder by the UV spectrophotometer(U-3501, Hitachi, Japan). The resistivity, carrier concentration, and Hall mobility of ZnS deposited on glass substrate as a function of post-annealing. -
본 연구에서는 RF Magnetron Sputtering System을 이용하여 ZnO계 투명전도막 증착시 Vaporization된 MeOH를 유입함으로써 박막증착과 동시에 표면의 Roughness를 제어하여 이에따른 전기적 특성 및 광학적 특성의 개선에 대하여 연구하였다. 실험방법으로 기존의 RF Magnetron Sputtering System에 Vaporization이 가능한 Ultrasonic을 이용하여 MeOH를 Vaporized시켜 MFC Controll을 통해 챔버에 유입하여 ZnO계 투명전도막의 박막증착과 동시에 표면 Texturing을 하였다. ZnO계 투명전도막의 박막증착시 Vaporized MeOH의 유입에 따른 광학적 특성변화를 UV-visible-nIR spectrometry로 조사하였으며, 전기적 특성 변화를 4-Point-Probe로 조사하였으며, 표면적 특성 변화를 Atomic Force Microscope(AFM), Scanning Electron Microscopy(SEM)를 조사하였으며, 박막의 결정성장특성 변화를 X-ray Diffraction(XRD)으로 조사하였으며, Vaporized MeOH 유입에 따른 박막의 성분분석을 Secondary Ion Mass Spectrometry (SIMS)로 조사함으로써 최적의 조건 및 공정을 확립하였다.
-
Song, JunYong;Jeong, Daeyoung;Kim, Kyoung Min;Park, Joo Hyung;Song, Jinsoo;Kim, Donghwan;Lee, JeongChul 128.1
In amorphous silicon and crystalline silicon(a-Si:H/c-Si) heterojuction solar cells, intrinsic hydrogenated amorphous silicon(a-Si:H) films play an important role to passivate the crystalline silicon wafer surfaces. We have studied the correlation between the surface passivation quality and nature of the Si-H bonding at the a-Si:H/c-Si interface. The samples were obtained by VHF-CVD under different deposition conditions. The passivation quality and analysis of all structures studied was performed by means of quasi steady state photoconductance(QSSPC) methods and fourier transform infrared spectrometer(FTIR) measurements respectively. -
Jang, Eunseok;Baek, Sanghun;Jang, Byung Yeol;Lee, Jeong Chul;Park, Sang Hyun;Rhee, Young Woo;Cho, Jun-Sik 128.2
스테인레스 스틸 유연기판 위에 플라즈마 화학기상 증착법 (plasma enhanced chemical vapor deposition)을 이용하여 nip 구조의 미세결정질 실리콘 박막 태양전지 (microcrystalline silicon thin film solar cell)를 제조하고 i${\mu}c$ -Si:H광 흡수층과 p${\mu}c$ -Si:H 사이에 i a-Si:H 버퍼 층을 삽입하여 i/p 계면특성을 개선하고 이에 따른 태양전지 성능특성 변화를 조사하였다.${\mu}c$ -Si:H 박막으로 이루어진 i/p 계면에서의 구조적, 전기적 결함은 태양전지 내에서 생성된 캐리어의 재결합과 shunt resistance 감소를 초래하여 개방전압 (open circuit voltage) 및 곡선 인자 (fill factor)를 감소시키는 것으로 알려졌다. 제조된 미세결정질 실리콘 박막 태양전지는 SUS/Ag/ZnO:Al/n${\mu}c$ -Si:H/i${\mu}c$ -Si:H/p${\mu}c$ -Si:H 구조로 제작되었으며 i/p 계면 사이의 i a-Si;H 버퍼층 두께를 변화시키고 이에 따른 태양전지의 특성을 조사하였다. 태양전지의 구조적, 전기적 특성 변화는 Scanning Electron Microscope (SEM), UV-visible-nIR spectrometry, Photo IV와 Dark IV를 통하여 조사하였다. -
Jeong, Daeyoung;Song, Junyong;Kim, Kyungmin;Park, Joo Hyung;Song, Jinsoo;Lee, Hi-Deok;Lee, JeongChul 129.1
a-Si:H/c-Si 구조의 이종접합 태양전지 전면 투명전도막으로 Indium tin oxide(ITO) 박막의 조건에 따라 태양전지 특성을 연구하였다. ITO 박막은 파우더 타겟으로 마그네트론 스퍼터링 방식으로 성막하였고, 증착 온도(Ts)에 따라 전기적, 광학적 특성을 비교, 분석하였다. 기판 증착 온도가 증가할수록 박막의 저항이 낮아지는 것으로 나타났으며$350^{\circ}C$ 조건에서 가장 낮은 저항($34.2{\Omega}$ /sq)을 보였다. 투과도 또한 기판 증착 온도가 올라갈수록 전반적인 향상을 나타냈다. a-Si:H/c-Si 기판의 MCLT(minority carrier lifetime)는$350^{\circ}C$ 에서 최적($359{\mu}s$ )의 결과를 나타냈다. 그 이상의 기판 온도에서는 오히려 감소하였는데, 이는 높은 온도에서의 a-Si:H/c-Si 계면의 열손상으로 판단된다. -
Kim, Kyung Min;Jeong, Dae Young;Song, Jun Yong;Park, Joo Hyung;Oh, Byung Sung;Song, Jinsoo;Lee, Jeong Chul 129.2
본 연구에서는 a-Si:H/c-si 구조의 이종접합 태양전지의 p a-Si:H 에미터 층의 박막 조건에 따라 태양전지 특성을 연구하였다. p, n-layer는 PECVD (Plasma-enhanced chemical vapor deposition) i-layer는 HWCVD(Hot wire chemical vapor deposition), ITO는 RF 마그네트론 스퍼터링법으로 제작하였다. p-layer의 도핑 농도, 기판 증착 온도, 증착 높낮이에 따라 특성을 비교 분석 하였다. QSSPC로 minority carrier life time, 자외 가시선 분광분석 장치로 투과 반사도를, Ellipsometer로 흡수 계수, 두께, FTIR로 막의 구성요소 등의 변화를 조사하여 개선된 p a-Si:H의 특성이 이종접합 태양전지에서 효율향상에 영향을 주는지 Photo IV와 EQE를 통하여 조사하였다. -
Nowadays, the number of PV module corporation is increasing due to demand growth of silicon solar module. However almost study of module is research about increasing of efficiency for it. This study is evaluation and development for process of module using the silicone encapsulation material instead of existing EVA sheet. We are changed adding material ratio on silicone and thickness of silicone. So we get better efficiency than EVA sheet through the evaluation for silicone liquid and modulation. Also, we are test after establishing manufacture system being able to quicker than existing modules line. The result of EVA sheet is average 207.47W and silicone material is 211.32W so we think that silicone is better than EVA sheet.
-
Kim, JungJin;Cho, Jun-Sik;Lee, Ji Eun;Jang, Ji Hun;Cho, Yong Soo;Park, Joo Hyung;Song, Jinsoo;Lee, Jeong Chul 130.2
본 연구에서는 RF magnetron sputtering을 이용하여 실리콘 박막 태양전지용 ZnO:Al 전면전극을 제작하고 다양한 식각조건에 따른 ZnO:Al 박막의 표면형상 변화와 함께 전기적 및 광학적 특성 변화를 조사하였다. pin 구조를 갖는 실리콘 박막 태양전지의 효율 향상을 위해서는 입사광의 산란효과에 따른 광포획 증가가 필수적이며 이를 위하여 ZnO:Al 전면전극의 표면텍스처링 형성이 필요하다. 식각용액으로는 HCl과 HF 등을 사용하였으며 식각용액 농도 및 식각시간을 변화시켰다. 식각 후의 ZnO:Al 박막의 표면형상은 SEM(Scanning Electron Microscope)과 AFM(Atomic Force Microscope)을 이용하여 분석을 하였고, UV-visible-nIR spectrometer를 이용하여 총 투과도 및 산란 투과도를 측정하였다. 이 외에도 four-point probe 및 Hall measurement를 이용하여 전기적 특성 변화를 조사하였다. 다양한 식각조건에 따라 제조된 ZnO:Al 박막 위에 실리콘 박막 태양전지를 제작하여 전면전극의 표면형상에 따른 태양전지 성능변화를 비교 분석하였다. -
우리나라는 2012년부터 신재생에너지 공급의무화제도(Renewable Portfolio Standards, RPS)의 도입을 확정하였다(지식경제부 고시 제2010-244호). RPS 제도는 기존의 발전사업자에게 총 발전량 중 일정량 이상을 신재생에너지 전력으로 공급토록 의무화하는 제도이다. RPS의 도입을 통해 일차적으로 신재생에너지의 보급 확대를 도모할 수 있으며, 부차적으로 신재생에너지 공급확대의 비용의 소비자 귀착을 기대할 수 있다. 본 연구는 RPS 제도로 인한 신재생에너지 보급확대의 비용이 소비자에게 전가된다는 가정 하에, 조건부가치평가법(Contingent valuation)을 적용하여 신재생에너지 전력에 대한 지불의사액(Willingness to pay)을 분석하였다. 본 연구의 주된 목적은 신재생에너지 전력에 대한 지불의사액을 분석하는 데 있어 지역별로 어떠한 차이가 나타나는지 알아보는 데 있다. 이에, 서울, 울산, 강원도, 전라남도의 4개 지역을 설문대상 지역으로 선정하였다. 서울은 신재생에너지를 포함한 에너지 관련 시설에 대한 경험이 거의 없는 비교군에 해당하며, 강원도와 전라남도는 신재생에너지의 이용이 활발한 지역을 대표하는 대조군에 해당된다. 울산은 신재생에너지 이용이 활발하지는 않으나 굴지의 산업단지가 입지한 지역으로, 대형 에너지 관련 시설에 대해 특수한 선호를 보일 것이라 추측되어 대조군으로 선정하였다. 본 연구에서는 이 4개 지역의 주민들을 대상으로 조건부가치평가법을 적용한 설문조사를 시행하여 신재생에너지 전력에 대한 지불의사액을 도출한 후, 이를 비교 분석하였다. 본 연구결과를 통해 신재생에너지에 관련된 경험이 선호에 어떠한 영향을 미치는지 파악할 수 있으며, 도출된 신재생에너지 전력에 대한 지불의사액은 향후 RPS 정책 도입시 전기요금 산정 관련 논의의 참고자료로 활용될 수 있을 것으로 기대된다.
-
2012년 RPS 제도가 시행되게 되면 발전설비용량 기준 500MW이상의 발전 사업자는 전체 전력생산량 중 일정 부분을 신재생에너지로 생산, 공급해야 한다. 최근 지경부에서 고시한 제5차 전력수급기본계획에서도 이러한 점을 반영하여 2024년까지 전체 발전량의 8.9%를 신재생에너지원으로 대체하겠다고 발표하였다. 신재생에너지 기술 수준, 시장여건 등을 고려하였을 때 앞으로 가장 크게 보급량(penetration)이 증가할 것으로 보이는 신재생에너지원은 태양광과 풍력인데 이 두 에너지원은 간헐성(intermittency)으로 인한 비급전성이라는 특징을 가지고 있어 향후 그 비중이 증가하면 전력계통의 안정성에 미치는 영향에 대해 고려해야할 것으로 보인다. 본 연구에서는 태양광과 풍력의 간헐성을 고려했을 때 추가적으로 발생하는 비용을 고려했을 경우 각 에너지원의 용량비용은 어떻게 되는지 알아보고자 한다.
-
As eco-friendly energy is in the spotlight, lots of countries are out to develop and disseminate renewable energy. However, Korea still remains in relative newcomer position for renewable energy. To overcome the present condition, it is necessary to carry out a study of establishment of renewable energy policy that is appropriate the present situation of Korea from examples of advanced countries. Among several renewable energies, wind energy is known to be the most reliable energy. Germany that has increased the share of wind energy in total energy supply is a representative leading country for wind energy. Therefore wind energy policy in Germany will be a role model for that in Korea. In this study, as a research of portfolio for wind energy policy of advanced countries, a wide survey for current status of wind energy and energy policy in Germany is carried out.
-
정부의 제1차 국가에너지기본계획(국무총리실 외. 2008)과 제4, 5차 전력수급기본계획(지식경제부 2008, 2010)을 바탕으로 장기 에너지 시스템 분석모형인 LEAP(Long-range Energy Alternatives Planning system) 모형을 이용하여 2050년까지 발전 부문에서 재생가능 에너지의 확대를 통한 에너지 전환 시나리오에 대하여 정량적인 분석을 하였다. 기준 시나리오, 정부 정책 시나리오, 지속가능 사회 시나리오에 대한 발전량 및 설비 구성, 수입의존도, 연료 다양성 등 에너지 시스템에 대해 분석하는 한편, 온실가스, 대기오염물질, 온배수, 토지이용 등 환경영향을 검토하고, 시나리오별 총 비용을 분석하였다. 본 연구의 의의는 영국, 독일, 미국, 일본 등 선진국에서 전력 장기 시나리오들을 검토하는 한편, 국내 발전 부문 재생가능 에너지 전환의 가능성과 의미에 대해 화두를 던지고자 함이다.
-
세계 각국에선 에너지 고갈, 에너지 공급 불안정성 심화, 기후변화 심화 등 에너지 위기에 직면하여 에너지 모형에 기초한 다양한 지속가능한 에너지 시스템 연구가 추진되었다. 최근 일본의 원전사고는 장기 에너지믹스에서 원자력을 주요 에너지원으로 고려해 온 각국의 에너지 정책에 영향을 미치면서 세계적으로 지속가능한 에너지 시스템 구축에 대한 논의와 모색을 더욱 촉발하고 있다. 이 논문에선 독일, 영국, 일본, 미국, 덴마크, 한국 등 세계 각국에서 정부나 민간 연구자들이 발표했던 지속가능 에너지 시스템 정책과 시나리오를 에너지 모형을 중심으로 분석하고자 한다. 이 분석은 향후 국내 지속가능 에너지 시스템 연구의 방향과 방법론 설정에 활용될 수 있다.
-
The goal of this study is the derivation of priority for business in the areas of green energy technologies. In this paper, we calculated the importance weights of impact factors using the AHP (Analytic Hierarchy Process) method in order to derivation of priority to the green energy technologies business. AHP is a useful method for evaluating multi-criteria decision making problems. To apply the AHP method, specialists for the assessment have been identified by using the concept of 'plan, do, see' and the decision-making hierarchy was established. We selected 5 criteria and 16 sub-criteria for impact factors by brainstorming. According to the result in this study, the most important impact factor is the possibility of commercialization, the second is the possibility of developing the fundamental technology, and the third is the possibility of convergence technology.
-
An energy modeling analysis method currently has been considered as a new approach for energy policy research, because the importance of renewable energy use has been emphasized more and more. This study used RETScreen model as a clean energy decision making methodology for adaptation to climate change and elimination of various pollutions. This modeling method includes five step standard analysis; energy model, cost analysis, GHG analysis, financial analysis, and sensitivity & risk analysis and it also assesses both conventional and modern energy sources and technologies. This methodology for the photovoltaic(PV) energy modeling is used to evaluate the energy production, financial performance and GHG emissions reduction of photovoltaic projects. In addition, the PV application systems are classified into three basic applications; On-grid system, Off-grid system and water pumping system. This study assesses the renewable energy techno-economic modeling method with the feasibility analysis result of 10 MW PV power plant in Abu Dhabi in United Arab Emirates. Furthermore this study stresses the importance of renewable energy model research by applying to domestic PV power plant which is now in preparation.
-
In this work, we analyzed correlations between life-cycle greenhouse gas (GHG) emissions and life-cycle cost of energy resources. Energy resources studied in this paper include coal, natural gas, nuclear power, hydropower, geothermal energy, wind power, solar thermal energy, and solar photovoltaic energy, and all of them are used to generate electricity. We calculated the mean values, ranges of maximum minus minimum values, and ranges of 90% confidence interval of life-cycle GHG emissions and life-cycle cost of each energy resource. Based on the values, we plotted them in two dimensional graphs to analyze a relationship and characteristics between GHG emissions and cost. Besides, to analyze the technical maturity, the GHG emissions and the range of minimum and maximum values were compared to each other. For the electric generation, energy resources are largely inverse proportional to the GHG emission and the corresponding cost.
-
2010년말 기준으로 약 3,200MW의 신재생에너지 발전소가 전력시장에 참여하여 전력거래를 실시하고 있다. 이 논문을 통해 2010년 1년간 운전한 신재생에너지 발전소들의 발전실적을 월별, 지역별 등으로 분석해 보고, 또한 과거 발전 실적과 비교 분석해 보고자 한다.
-
본 연구는 바이오에너지 분야의 성장을 혁신 시스템 관점에서 이해할 필요성을 논하고, 시스템 관점에서의 이론적 분석 틀을 제공하고자 한다. 신재생에너지 보급에 의한 지역 및 국가 에너지 시스템 전환을 기술 혁신의 과정으로 이해할 때 혁신 시스템 관점은 기술 개발로부터 선별 및 확산에 이르기까지 관계되는 다양한 주체와 이들 간의 네트워크, 제도 관계를 통합적으로 바라보도록 한다. 특히 혁신 시스템에 대한 동학적 접근은 시스템의 변화에 초점을 맞추어 변화의 동인을 파악하는데 '시스템 기능'이라는 개념을 사용하면 복잡한 바이오에너지 성장 과정에 대한 시기별 접근과 기술 사례별 비교 분석이 용이해진다. 본 연구는 혁신 시스템 관점과 관련된 다양한 개념 정리 및 바이오에너지 분야의 성장에 대한 기존 시스템 관점의 연구들을 검토하여 바이오에너지분야의 성공 및 실패 요인을 도출하고 우리나라 바이오에너지 분야에 적합한 시스템 분석틀을 제시한다.
-
정부는 국가에너지 기본계획을 통하여 2030년까지 1차 에너지에 대해 신재생에너지 비중을 11%까지 확대하겠다는 목표를 설정하였다. 이에 대한 일환으로 신재생에너지 지방보급 사업 등 지역 별로 신재생에너지에 관한 투자 및 보급이 활발하게 진행되고 있는 상황이다. 더불어, 각 지방자치단체에서도 지역에 맞는 신재생에너지 계획을 수립하여 신재생에너지를 보급하고자 노력하고 있다. 신재생에너지 사업은 지역의 경제발전과 밀접한 연관을 가지고 있기 때문에 그 중요성이 더욱 부각되고 있는 실정이다. 본 연구에서는 우리나라 각 지역별 신재생에너지 계획안을 검토하여 어떠한 에너지원에 중점을 두고 사업을 추진하고 있는지 그 현황을 파악하고자 한다. 또한 이들 지역의 신재생에너지 계획안이 해당 지역의 신재생에너지 잠재량과 같은 지역의 특성을 잘 반영하고 있는지, 해당 지역의 신재생에너지 현황은 어떠한지 에너지기술연구원과 에너지관리공단의 관련 자료를 참고하여 검토할 것이다. 이를 통해 궁극적으로 각 지역의 신재생에너지 계획이 해당 지역이 보유하고 있는 자원(자연자원, 인력자원, 경제적 재원 등)을 효율적으로 활용하고 있는지 분석하고자 한다. 본 연구의 결과는 기존의 지역별 신재생에너지 계획을 평가하는데 사용될 수 있으며, 향후 지역 및 국가단위의 에너지 계획 수립에 참고자료로 활용될 수 있을 것이다.
-
Compared with a traditional power system of electricity providers, distributed power systems consist of power suppliers which are small and demand-oriented. Each small power supplier tends to utilizes renewable energy sources such as solar and wind power. It is because that home renewable energy systems do not need a large scale infrastructure which is required for traditional power plants. In this work we study an economic feasibility of such a renewable energy source. We describe how renewable power generation works and what it brings in terms of economic benefits. Also, we analyze limitations by the current policy and their possible solutions.
-
본 연구에서는 알콜계 물질인 1-propanol과 2-propanol이 가스 하이드레이트 형성과정에서 격자내로 포집됨과 열역학적 촉진제로서 작용함을 알아보기 위해
$CH_4$ (또는$CO_2$ ) + 1-propanol (또는 2-propanol) + 물계의 가스 하이드레이트 3상 평형 (하이드레이트(H) - 물(Lw) - 기상(V))을 측정하였으며,$^{13}C$ NMR 분석을 하였다. 1.0, 5.6, 10 mol%의 농도 1-propanol (또는 2-propanol) 용액을 가스 하이드레이트 계에 첨가하여 3상 평형을 측정한 결과,$CH_4$ 하이드레이트의 경우 전반적으로 촉진현상을 보였으며 5.6 mol%에서 가장 큰 촉진효과가 나타났다. 하지만$CO_2$ 하이드레이트의 경우 순수$CO_2$ 하이드레이트에 비해 저해효과가 나타났으며 농도가 높아질수록 저해현상은 커짐을 확인할 수 있었다.$^{13}C$ NMR을 통한 동공점유 특성과 하이드레이트 구조 분석 결과$CH_4$ + 1-propanol (또는 2-propanol)은 구조-II를 형성하며 1-propanol (또는 2-propanol)이 동공에 포집되어 있음을 확인할 수 있었다. 이상의 결과로부터 알콜계 물질이 단순히 저해제로만 작용하지 않고 가스 하이드레이트 형성에 참여하는 촉진제로 작용할 수 있다는 사실을 알 수 있었다. -
메탄 하이드레이트는 낮은 온도와 높은 압력 조건에서 물분자들의 격자구조에 메탄가스분자가 포획되어 수소결합으로 형성되는 외관상 얼음과 비슷한 결정성 화합물이다.
$1m^3$ 의 메탄 하이드레이트는 표준상태에서$172m^3$ 의 메탄가스와$0.8m^3$ 의 물로 분해되며,$-10^{\circ}C{\sim}-20^{\circ}C$ 의 온도에서는 하이드레이트 입자표면에서 생성되는 얼음막으로 인하여 상압에서도 안정하게 존재하는 자기보존 효과를 가지고 있다. 따라서 이와 같은 특징을 천연가스 수송 및 저장의 방법으로 이용할 경우$-162^{\circ}C$ 의 초저온을 만들고 유지시키기 위하여 고가의 설비를 필요로 하는 기존의 LNG 수송방법을 대체할 수 있다. 특히 연간 천연가스 소비량을 0.4 ~ 1.0 million ton으로 가정했을 때, 하이드레이트 수송방법은 LNG 수송에 비해 18 ~ 25% 정도의 비용을 절약할 수 있는 경제적인 방법으로 알려져 있다. 그러나 하이드레이트를 인공적으로 제조할 경우 물분자와 가스분자의 반응율이 낮기 때문에 하이드레이트가 생성되기까지 많은 시간이 소요되며, 하이드레이트에 포획되는 가스분자의 양도 적다. 따라서 본 연구에서는 이와 같은 문제점을 해결하기 위하여 다공성 물질인 천연 제올라이트와 제올라이트 13X를 이용하여 제올라이트 혼합유체를 제조하였으며, 메탄가스와 반응시켜 하이드레이트를 생성시키는 실험을 수행하였다. 그 결과, 하이드레이트 생성 시 천연 제올라이트와 제올라이트 13X 모두 0.01 wt%의 혼합비율에서 가장 좋은 효과를 나타내었으며, 하이드레이트에 포획된 가스의 양은 같은 과냉도 조건에서 천연제올라이트와 제올라이트 13X 혼합유체를 이용하여 하이드레이트를 생성 시켰을 때, 증류수보다 각각 4배, 5배 높음을 보였다. 또한 낮은 과냉도에서 하이드레이트 생성 시 제올라이트, 제올라이트13X 혼합유체에서 하이드레이트 생성시간이 증류수에서 하이드레이트를 생성시킬 때보다 빨라짐을 확인하였다. -
석탄가스화복합발전(IGCC)공정에서 가스화기를 거쳐 생성된 합성가스로부터
$CO_2$ 를 효과적으로 분리/회수하기 위해 가스 고형화법을 제안하였다. 가스 하이드레이트 형성과정에서의 반응특성을 살펴보기 위하여 반응시간에 따른 가스소모량과 기상의$CO_2$ 조성 변화를 측정하였다. 순수계와 촉진제 첨가계 (TBAB (10, 40 wt%), TBAF (10, 34 wt%), THF (4, 19 wt%))에 대하여 하이드레이트 생성 후의 기상과 하이드레이트상의$CO_2$ 조성을 측정하였으며, 그 결과 하이드레이트 형성법에 의해 고농도의$CO_2$ 가 하이드레이트상에 포집되는 것을 확인하였다. 가스 소모량 측정실험에서는 THF 19.1 wt%를 첨가하였을 때 가장 큰 소모량을 보였으며, TBAF 10 wt%를 첨가하였을 때 가장 적은 가스소모량을 보였다.$CO_2$ 조성 변화 실험에서는 가스 소모량 실험과 마찬가지로 THF 19.1 wt%를 첨가하였을 때 가장 큰 조성변화를 보였다. 이는 THF의 첨가로 인하여 가스 하이드레이트로의 전환율 증가로 많은 양의$CO_2$ 기체가 하이드레이트 상에 포집되었음을 나타낸다. 속도론적인 측면에서는 모든 실험조건에서 하이드레이트 형성반응이 1시간 이내에 대부분 종결되는 것을 볼 수 있었다. 또한$^1H$ -NMR을 통하여 혼합가스 하이드레이트의 구조적인 분석을 진행하였다. 본 실험에서 얻어진 결과는 가스 하이드레이트 형성법을 이용한 합성가스 분리 공정 개발에 중요한 기초자료가 될 것으로 사료된다. -
Molecular behaviors and crystal structures of the binary hydrates of
$CH_4$ and ethanol were identified by means of 13C solid-state NMR and powder XRD methods at various concentrations of ethanol. In addition, NMR peak areas were used to calculate cage occupancies for both guest species. Obtained results showed that more$CH_4$ molecules are captured into hydrate phase per unit mass of ethanol molecules because$CH_4$ molecule can occupy sII large cages more, and pure$CH_4$ hydrate can form more as well at lower ethanol concentrations. Even though tuning phenomenon was already reported for some aqueous hydrate promoters such as THF, aqueous ethanol solutions are found to play the same tuning role in the binary clathrate hydrates in this study. -
Ryu, Byong-Jae;Lee, Sung-Rock;Yoo, Dong-Geun;Kim, Gil-Young;Chun, Jong-Hwa;Bahk, Jang-Jun;Kim, Ji-Hoon;Lee, Joo-Yong 147.1
지식경제부 가스 하이드레이트 개발사업의 일환으로 동해 울릉분지 가스 하이드레이트 2차 시추(Ulleung Basin Gas Hydrate Drilling Expedition: UBGH2)가 2010년 7월 8일부터 9월 30일까지 D/V Fugro Synergy를 이용하여 수행되었다. UBGH2 수행을 위해 선정된 13개 site에서 약 1개월 동안 Schlumberger사의 장비를 이용 Logging-While-Drilling/Measurement-While-Drilling(LWD/MWD) 자료를 취득하였다. LWD/MWD 자료는 선상에서 분석되었으며, 이 결과는 coring 및 borehole plan 수립을 위하여 활용되었다. Coring Phase 동안 10개 site의 18개 hole로부터 퇴적물 코어 시료를 채취하고 선상에서 퇴적학, 지구화학, 생지화학, 물리적 특성 등 각종 분석과 측정 작업을 수행하였다. 약 2개월에 걸쳐 수행된 coring phase 동안에 2개 site에서 FAOL(Fugro Alluvial Offshore Limited)사의 장비를 이용 Wireline Logging/Vertical Seismic Profile(WL/VSP) 자료도 취득하였다. LWD/MWD phase와 coring phase 동안 12개 site에서 무인잠수정(remotely operated vehicle: ROV)를 이용하여 퇴적물 시료 채취, 해저면 관찰, 용존메탄 측정 등의 작업을 수행하였으며, 선상에서 취득된 이들 자료를 분석하였다. Coring을 수행한 모든 site에서 가스 하이드레이트 부존을 확인하였으며, 다양한 산상의 가스 하이드레이트 실물을 회수하고 분석하였다. -
새로운 에너지원으로서의 가스 하이드레이트 개발 연구는 한국에서는 2005년 산업자원부에 의해 가스하이드레이트 개발 연구 사업이 정식으로 출범하면서 활발히 진행되기 시작하였다. 2007년도에 종료된 1단계 연구를 통하여 동해에서 가스 하이드레이트 부존이 확인됨에 따라 2단계에서 부터는 가스하이드레이트 생산 연구가 연구의 중심으로 떠오르게 되었다. 생산 연구는 물성/생산 실험 연구, 전산모사 연구, 해외 현장 시험 생산 연구로 크게 나뉘어 질 수 있는데 현재 한국에서는 물성/생산 실험 연구가 가장 활발히 진행되어 왔다. 이에 따라 보다 체계적이고 계획적인 연구를 위하여 기 실험된 연구를 종합 분석하여 체계적인 실험 결과의 활용과 향후 연구 계획을 하고자 한다. 본 발표에서는 기 실행된 실험 연구를 수행기관, 시료의 크기, 경계조건 등의 실험 규모, 시료의 종류, 하이드레이트 형성 조건, 측정 물성, 채택 생산 기법 등의 실험 내용 등을 종합하여 소개하고자 한다. 1단계에서는 주로 실험실 스케일, 인공 모래 시료, 인공 가스하이드레이트를 이용한 실험연구가 주를 이루었으며 이를 보완하기 위하여 2단계에서는 중규모, 자연시료, 자연 하이드레이트를 이용한 실험연구가 시작되었다. 초기 단계에서 생산 기법으로 감압법, 열수 주입법, 열자극 법, 화학 억제제 주입법, 치환 생상법 등이 연구되었으며 그 결과 감압법을 주 생산 기법으로 하여 열수 주입법, 열자극법, 화학 억제제 주입법 등을 하이드레이트 재생성 억제기법으로 혼합하여 쓰는 하이브리드 기법들이 연구 되었으며 현재 세계적인 수준의 실험 연구 기술 수준을 보유 하고 있는 치환 생산법 연구가 또한 현재까지 활발히 진행되고 있다.
-
본 연구에서는 가스 하이드레이트의 미래 상업생산을 위한 연구활동으로 동해 울릉분지 현장시료를 채취하여 가스 하이드레이트 함유토의 열전도 현상에 관한 연구를 실시하였다. 두 종류의 현장시료를 이용하여 메탄 하이드레이트를 생성하여 공극비 및 포화도에 따라 조건을 달리하여 실험을 수행하였다. 열전도도 측정을 위하여 Transient Plane Source (TPS) 기법을 이용하였다. 현장시료의 사용에 앞서 예비실험으로써 F110표준사를 사용, 비교 분석 자료로써 활용하였다. 하이드레이트 생성 확률을 높이는 기법으로써 불포화시료를 동결, 해동 후 가스를 주입하였으며 동결된 불포화 시료의 열전달양상의 변화를 함께 고찰하였다. 실험결과, 하이드레이트의 포화도가 증가함에 따라 함유토의 열전도도의 증가함을 알 수 있어다. 거의 동일한 물과 GH의 열전도도에도 불구하고 하이드레이트 결정화 작용으로 동일한 포화도의 불포화 시료와 비교하여 약간의 상승을 보였다. 또한 공극비 및 흙을 구성하는 미네랄의 성분에 따라 열전도도의 발현 양상이 상이함을 관찰하였다. 이에 차후 하이드레이트 생산을 위한 현장 측정 및 전산 모사시 이에 관한 고려가 필요할 것으로 사료된다.
-
천연의 메탄 하이드레이트를 생산하기 위한 방법으로는 크게 다음의 세 가지가 알려져 있다; 감압법, 열 자극법, 저해제 주입법. 갑압법이 가장 경제성이 높은 방법으로 보고 있으며, 이를 활용한 개발생산 시에는 해리 이후의 잔류 물에서 하이드레이트 전구체라고 알려진 하이드레이트 구조가 남아 있으며 이는 생산된 메탄 가스의 이송 과정에서 하이드레이트 재생성의 위험을 높이게 된다. 하이드레이트 재생성을 방지할 수 있는 한 가지 수단으로는 억제제를 주입하는 방법이 가능한데, 적절한 양을 주입함으로써 생산의 경제성을 높일 수 있다. 최근 들어 kinetic 억제제의 적용이 인기를 얻고 있는 바, 수용성 고분자인 이들 억제제를 적용하여 초기 하이드레이트 핵 생성을 지연시킬 수 있다. 이들 kinetic 억제제를 메탄 하이드레이트 생산 과정에서 투여하는 방법을 실험적으로 측정해 보았고, 잔류의 하이드레이트 구조에 대한 존재여부에 대하여 간접적으로 증명해보고자 하였다. kinetic 억제제로는 Poly Vinyl Caprolactam (PVCap)을 선택하였다. 해리압력, PVCap 주입 농도에 변화를 주면서 메탄 하이드레이트 생산, 수송과정에서 발생할 수 있는 하이드레이트 재생성 억제에 대한 효과를 실험적으로 측정하였다.
-
Structure-II hydrate has been highlighted due to its higher gas storage capacity and favorable thermodynamic conditions. In this study, we introduce a new structure-II hydrate former, tert-butyl hydroperoxide (TBHP) and confirm the structural characteristics through High-Resolution Powder Diffraction (HRPD),
$^{13}C$ solide-state NMR and Ramanspectroscopy. Here,we also investigated the thermodynamic stability of binary(TBHP+gaseous) clathrate hydrates. The experimental data were generated using an isochoric pressure-search method. The dissociation data for (TBHP +gaseous) clathrate hydrates are compared with the other hydrocarbon hydrate and pure gaseous hydrate. -
Unlike non-ionic clathrate hydrates stably formed by van der Waals interaction between a guest molecule and a surrounding host framework, ionic clathrate hydrates are stabilized by ionic interaction between an ionic guest molecule and the host water-framework. Here, we firstly described the stable entrapment of the superoxide ions in
${\gamma}$ -irradiated$Me_4NOH+O_2$ hydrate. Owing to peculiar direct guest-guest ionic interaction, the lattice structure of${\gamma}$ -irradiated$Me_4NOH+O_2$ hydrate shows significant change of lattice contraction behavior even at relatively high temperature(120K). Particularly, we note that ionic-induced dimensional change is much greater than thermal-induced change. Such findings are expected to provide useful information for a better understanding of unrevealed nature of clathrate hydrate fields. -
It is of great importance to predict operating parameter characteristics of an integrated fuel processor by the increased life-time and system performance. In this study, computational analysis is performed to gain fundamental insights on transport phenomena and chemical reactions in reformer which consists of preheating, steam reforming, and water gas shift reaction beds. Also, a top-fired burner locates inside of the reforming system. The combustor is providing thermal energy necessary for the steam reforming bed which is a endothermic catalytic reactor. Two-dimensional numerical model of the integrated fuel processing system is introduced for the analysis of heat and mass transport phenomena as well as surface kinetics and catalytic process. A kinetic model was developed and then computational results were compared with the experimental data available in the literature. Subsequently, parameter study using the validated steam methane reforming model was conducted by considering operating parameters, i.e. steam to carbon ratio and temperature.
-
본 연구에서는 일단 수성가스전이반응 (Single stage water gas shift reaction)을 위해 높은 활성을 가진 백금 담지 촉매를 함침법 (Incipient wetness impregnation method)으로 제조하여 높은 공간 속도 (Gas hourly space velocity)
$45,515h^{-1}$ 에서 담체에 따른 촉매 활성을 평가하였다. 담체는$CeO_2$ ,$ZrO_2$ , MgO, MgO-$Al_2O_3$ (MgO = 30 wt%) 그리고$Al_2O_3$ 를 사용하였으며 백금의 담지량은 1 wt%로 고정하였다. BET, XRD, TPR, CO-chemisorption 분석을 통하여 담체의 구조적 특성이 촉매 활성에 미치는 영향에 대하여 조사하였다. -
선택적 CO 산화반응(PrOx)에 사용되는 촉매 중 Pt, Ru, Rh 등의 귀금속 계 촉매들은 비귀금속 계 촉매에 비해 활성이 좋은 반면 가격이 비싸다는 경제적인 제한점이 있다. 따라서 소량의 귀금속을 사용하여 높은 활성의 촉매를 제조하고자 활성금속의 고분산 담지 방법에 대한 연구가 이루어지고 있다. 본 연구에서는 담체인
${\gamma}-Al_2O_3$ 표면에 활성금속인 Pt의 고분산 담지를 위해 증착-침전법(Deposition-precipitation)을 적용하였으며 용액의 pH 변화에 따른 Pt 금속 입자의 분산도에 대한 영향을 살펴보았다. Pt의 함량은 1wt%로 고정하였고 침전제로 NaOH를 사용하여 용액의 pH를 pH 7.5 ~ 10.5로 변화시켰다. 제조된 촉매는 세척 후$400^{\circ}C$ , 3시간 소성 하였다. 제조된 1wt% Pt/$Al_2O_3$ 촉매의 특성분석을 위해 BET, TPR, CO-chemisorption을 수행하였다. PrOx 반응 실험은 GHSV=60,000$ml/g_{cat}{\cdot}h$ ,$T=100{\sim}200^{\circ}C$ ,${\lambda}$ =4 조건에서 수행되었으며 반응 전에 촉매는$400^{\circ}C$ , 3시간 환원 후 사용하였다. 촉매의 특성분석과 PrOx 반응 실험 결과를 통해 촉매가 담체 위에 고분산 되는 최적의 pH를 확인할 수 있었으며, 기존의 함침법으로 제조된 촉매와 성능 비교를 통해 제조방법에 따른 영향을 살펴보았다. -
In this work, we prepared Mg nanoparticles loaded graphite oxide (Mg-G) as a function of Mg content in order to investigate hydrogen storage behaviors. The structure and morphology of the Mg-G samples were characterized by X-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM). The textural properties of the samples were evaluated using
$N_2$ /77 K adsorption isotherms. The hydrogen adsorption capacities were investigated at 298 K/10 MPa. As a result, the hydrogen adsorption capacities of the Mg-G were enhanced with increasing the Mg content. Therefore, it was found that the presence of Mg on graphite surfaces created hydrogen-favorable sites, resulting in enhancing the hydrogen adsorption capacity. -
In this work, we prepared ultramicroporous carbons (UC) prepared by pyrolyzing poly(vinylidene fluoride) with different carbonization temperatures, and investigated the hydrogen storage behaviors. The surface functional groups and specific elements of UC were confirmed by Fourier-transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS), respectively. Textural properties were analyzed using
$N_2$ adsorption isotherms at 77 K. The hydrogen storage capacity of the UC samples were investigated by BEL-HP at 298 K/10 MPa. From the results, it was found that the hydrogen storage capacity was enhanced with increasing of specific surface area, resulting from the formation of ultramicropore on the UC. -
DME is acronym of dimethyl ether, which is spotlighted as an ideal fuel to produce hydrogen due to its high hydrogen/carbon ratio, high energy density and easiness to carry. In this research, we calculated thermodynamic hydrogen (or syngas) yield from DME autothermal reforming and compared to other fuels. The reforming efficiency was about 80% above
$700^{\circ}C$ . Lower OCR has higher reforming efficiency but, it requires additional heat supply since the reactions are endothermic. SCR has no significant effect on the reforming efficiency. The optimized condition is$700^{\circ}C$ , SCR 1.5, OCR 0.45 without additional heat supply. Comparing to other commercial gaseous fuels (methane and propane), DME has higher selectivity of$H_2O$ and$CO_2$ than the others due to the oxygen atom in the molecule. To apply DME autothermal reforming to real system, a proper catalyst is required. Therefore, it is performed the experiment comparing various novel metal catalysts based on CGO. Experiments were performed at calculated condition. The composition of product was measured and reforming efficiency was calculated. The catalysts have similar efficiency at high temperature(${\sim}800^{\circ}C$ ) but, CGO-Ru has the highest efficiency at low temperature ($600^{\circ}C$ ). -
Partial oxidation reformer was fabricated and operated using commercial transportation fuels. Fuel injector and heating coil were used for fuel atomization and startup, respectively. The reformer was designed to produce syngas for
$150{\sim}200W_e$ class solid oxide fuel cell. The reformer was operated in the$O_2$ /C range between 0.6 and 0.8 while the capacity was fixed at$150W_e$ . The temperature range in catalyst bed was between$500^{\circ}C$ and$900^{\circ}C$ . Only 83% fuel was converted to$H_2$ , CO,$CO_2$ and$CH_4$ at the operating conditions. The lowest temperature increase to$700^{\circ}C$ when the reformer was operated at$200W_e$ , Although the temperature profiles was improved, fuel conversion was 88%. On the other hand, fuel was completely converted when micro-reactor operated at the same condition. This difference maybe due to aromatic compounds formation at homogeneous region. In addition, a significant amount of coke deposition was observed at vent line. Homogeneous reaction depends on the degree of mixing. For this purpose, two fluid nozzle and Ultra sonic injector were compared to investigate the effect of atomization. Sauter mean diameter(SMD) of Ultra sonic injector was lower than two-fluid nozzle at test condition. However, conversion efficiency and fuel conversion were not improved by using two-fluid nozzle. these results imply that the temperature of homogeneous reaction region should be controlled to prevent coke formation. -
In this study, we prepared the activated graphite nanofibers (A-GNFs) via chemical activation with KOH reagent. The effect of A-GNFs on the surface and textural properties of Ni-loaded graphite nanofibers (Ni/GNFs) was investigated by X-ray diffraction (XRD), transmission electron microscope (TEM), and Brunauer-Emmett-Teller (BET). The textural properties of samples were investigated by
$N_2$ /77K adsorption isotherms. The electrochemical performances were investigated by cyclic voltammetry. As a results, the electrochemical performances of Ni/GNFs were improved with usage of A-GNFs. This could be interpreted by the high specific surface area and large total pore volume of the A-GNFs. -
세계는 지금 지구 온난화 및 화석연료의 고갈로 인해 대체 에너지 자원의 확보문제가 급속히 대두되고 있다. 이에 조류발전은 오염이 발생하지 않는 친환경 에너지원으로서, 날씨나 계절에 상관없이 항상 발전할 수 있는 신뢰성 있는 에너지이며, 높은 밀도를 가지는 작동유체가 수차에 미치는 영향 또한 크므로 지속적으로 예측이 가능한 장점을 가지고 있다. 이러한 조류에너지는 실 해역에 적용하기 위해서는 전격유효 전력이 생산 가능한 지리적 요인에 대한 고찰과 더불어 조류발전 터빈의 개념설계가 고려되어야 한다. 본 연구는 다양한 설치 공간을 형성할 수 있으며, 장, 단점이 보완될 수 있는 조류발전 터빈의 개념설계 연구 단계로서, 내부 유동 특성을 고려하여 입구를 설계하였으며, 일정한 속도로 유입되는 유량을 노즐의 장착을 통해 에너지 밀도를 높일 수 있게 된다. 이러한 개념형상 설계로 추가 작동이나, 장치의 사용 없이 양방향 발전이 가능해 진다.
-
Due to global warming, the need to secure an alternative resource has become more important nationally. Due to the high tidal range of up to 9.7m on the west coast of Korea, numerous tidal current projects are being planned and constructed. To extract a significant quantity of power, a tidal current farm with a multi-arrangement is necessary in the ocean. The rotor, which initially converts the energy, is a very important component because it affects the efficiency of the entire system, and its performance is determined by various design variables. The power generation is strongly dependent on the size of the rotor and the incoming flow velocity. However, the interactions between devices also contribute significantly to the total power capacity. Therefore, rotor performance considering the interaction problems needs to be investigated for generating maximum power in a specific field. This paper documents the characteristics of wake induced by horizontal axis tidal current power turbine.
-
Previously, many researchers assessed nearshore wave energy in two ways. The first is a simulation with respect to the offshore wave time series to validate the wave buoy data and the wave model results, and the other is to simulate the representative waves of typical seasonal wave conditions. The former requires enormous computational time and effort. The latter yields inspection on the patterns for the spatial and temporal distribution of nearshore wave energy but tends to underestimates the amount of wave energy in the nearshore region owing to the correlation between the significant wave height and wave period.
$\ddot{O}$ zger et al. (2004) derived the stochastic wave energy formulation by introducing a correction factor explicitly in terms of the covariance of the wave energy and significant wave height. In this study, a correction factor was applied for the assessment of nearshore wave energy obtained by numerical simulation of wave transformation with respect to representative waves. -
지구온난화에 따른 대체에너지 자원확보가 국가적으로 중요한 과제로 대두되고 있고 여러 대체에너지원 중 국내의 해양에너지는 잠재량이 매우 높다. 여러 해양에너지 중에서 빠른 흐름을 이용하는 조류발전은 서해안과 남해안에 적용하기에 적합하며 해양환경을 보존하면서 많은 에너지를 생산할 수 있는 장점이 있다. 조류발전에서 1차적으로 에너지를 변환시키는 로터는 주요한 장치중의 하나로 여러 변수에 의해 그 성능이 결정된다. 로터의 블레이드 수, 형상, 단면적, 허브, 직경 등 여러 요소를 고려하여 설계되어야 한다. 또한 조류발전을 적용하는 해양환경에서 최대 출력을 생산할 수 있는 로터가 적용될 수 있도록 블레이드의 후류 영향을 고려해야한다. 본 논문에서는 날개요소이론을 바탕으로 수평축 조류발전 터빈을 설계하여 실험 및 유동해석을 통해 성능을 평가하고, 후류에 미치는 영향을 분석하였다.
-
In the present study, two numerical methods were developed and compared for the performance prediction of the horizontal axis energy conversion turbine. The Blade Element Momentum Theory was adopted, and the rotating reference frame method for Computational Fluid Dynamics solver was also used. Hybrid meshing was used for the complex geometry of turbines. The analysis results using each method were compared to figure out a better method for the performance prediction.
-
Dye to recent development such as increasing price of fossil fuels and energy offers such a solution. Wave energy supplies. Weve energy offers such a solution. Wave energy is the most consistent of all the intermittent renewable energy sources. In addition to this, very large energy fluxes occur in the ocean waves and by using appropriate wave energy converters the energy can be harnessed. The present study looks at utilizing a direct drive turbine of cross flow type to extract energy from ocean waves indirectly. This novel design incorporates a turbine in an enclosed in a closed tank. utilizing the energy generated from sloshing.
-
The rotor design is fundamental to the performance and dynamic response of the Counter-rotating marine tidal current turbine. The wind industry has seen significant advancement single rotor blade technology, offering considerable knowledge and making it easy to transfer to tidal stream energy converters. In this paper, 3D flow and performance an alysis on a 100 kW counter-rotating marine current turbine blade was carried out by using the 3-D Navier-Stokes commercial solver(ANSYS CFX-11.0) to provide more efficient design techniques to design engineers. The front and rear rotor diameter is 8m and the rotating speed is 24.72rpm. Hexahedral meshing was generated by ICEM-CFD to achieve better quality of results. The rated power and its approaching stream velocity for design are 100 kW and 2 m/s respectively. The pressure distribution on the blade's suction side tells us that the pressure becomes low at the leading edge of the airfoil as it moves from the hub to the tip.
-
Incheon Bay of Korea is one of the most famous regions for high tidal range. Ministry of Land, Transport and Maritime Affairs(MLTM) has implemented preliminary investigation for tidal power energy development in this area since 2006. Through field observations, various kinds of marine data consisting of depth and geography, marine weather, tidal currents, wave, seawater characteristics, geology, marine ecosystem and marine environment were gathered. To use these data efficiently for the determining of feasibility of developing and appropriateness of project scale, spatial data management and application system is essential. Therefore, in this study, the concept, methodology and procedure of spatial data modeling are defined for tidal energy development. Spatial data modeling consists of essential model relating to tidal energy directly and optional model including environmental factors. Essential model is composed with fundamental elements like as depth, geography, and several numerical modeling results(tide, tidal current, wave).
-
Sustainable energy generation is becoming extremely imperative due to the expected limitations in current energy resources and to reduce pollution. Especially, because of its considerable energy potential, ocean wave energy has been investigated with regard to power generation. To develop large high power wave generator system, it is important to make a small scale proto type and to test that. Thus the objective of this research is to examine the characteristics of a mechanically excited generator system having small power capacity experimentally. The water reservoir (4 m length, 1.5 m width and 1.8 m depth) having a wave maker to make arbitrary height and period of the water wave was made. The proto type consists of three main parts; a buoy, rack-pinion base one-way mechanism, and a wave generator(Fig.1). The water wave is going up and down and the hexahedron buoy is following the wave. The rack gear attached to the buoy is also going up and down to roll the pinion connected to an electric generator then it produces electricity. The experiments were performed with several conditions of water waves, and the power outputs over 30 W could be measured for some conditions. In future works, to achieve higher performance for the proto type, the effects of primary parameters (buoy shape and mass, etc.) on the system efficiency will be identified.
-
Motions in nature, for example ocean wave, has been playing a significant role for generating electricity production in our modern life. This paper presents an innovative approach for electric power conversion of the vast ocean wave energy. Here, a floating-buoy wave energy converter (WEC) using hydrostatic transmission (HST), which is shortened as HSTWEC, is proposed and designed to enhance the wave energy harvesting task during all wave fluctuations. In this HSTWEC structure, the power take-off system (PTO) is a combination of the designed HST circuit and an electric generator to convert mechanical energy generated by ocean wave into electrical energy. Several design concepts of the HSTWEC have been considered in this study for an adequate investigation. Modeling and simulations using MATLAB/Simulink and AMESim are then carried out to evaluate these design concepts to find out the best solution. In addition, an adaptive controller is designed for improving the HSTWEC performance. The effectiveness of the proposed HSTWEC control system is finally proved by numerical simulations.
-
The high fuel flexibility of gas turbine power system has boosted their use in a wide variety of applications. Recently, the demand for biogas generated from the digestion of organic wastes and sewage waste water as a fuel for gas turbines has increased. We investigated the performance of high pressure biogas compression system and operating conditions for supplying biogas. The total flow per minute of biogas from food waste water digestion tank is
$54Nm^3$ . The main type of biogas compression system is the reciprocating system and screw type system. The target of biogas mechanical data is the as belows; inlet pressure 0.045bar, supplying biogas temperature is$30{\sim}60^{\circ}C$ , and final pressure is above the 25 bar. Also, inlet conditions of biogas consist of CH4 48.5%~83%,$H_2S$ Max. 500ppm,$NH_3$ Max. 1,500ppm and Siloxane 2.7~4.6ppm. The boosting Blower system raises a pressure from 0.045bar to 1bar before main compressor. The main system lay out of reciprocating consisits of compressor driver, filter, cooling system, blowdown vessel, control system and ESD(Emergency Shut Down) system. And an enclosure package needs to be installed for reducing noise up to 75dB. The system driver is the electronic motor of explosion proof type. Forthe compressor system reliable operation, the cleaning system something like particulate filter needs to be set up in the inlet of compressor and Coalescing Filter in the outlet of compressor. Particulate Filter has to be removed above$10{\mu}m$ size of the particles in biogas. The coalescing filter(Micofine Borosilicate Glass Fibers Filter treated phenol acid) also removes moisture and oil of above$0.3{\mu}m$ to be involved in high pressure biogas up to 90%~98%. -
대체 에너지 자원 중 폐기물의 소화 가스를 이용한 바이오가스 발전은 이산화탄소에 비해 온실효과 영향력에 21배에 해당하는 메탄가스를 연료로 사용하여 환경부하를 저감시키고 에너지를 생산한다. 바이오가스에 포함된
$H_2S$ 는 연소 후$SO_2$ 형태로 발생되는데$SO_2$ 는 수분과 반응을 하게 되면$H_2SO_4$ 등의 강한 산성을 띄는 물질로 생성되어 배관 및 발전기에 손상을 주고 저온부식현상을 유발하게 하며, 동물이나 인체에 노출되면 기관지 수축현상이 일어나 호흡기에 영향을 주는 질식성을 띄는 가스이다. 축산바이오가스에 포함된$H_2S$ 의 함유량과 가스엔진의 연소 시 배출되는$SO_2$ 배기가스 성분의 관련성을 검증하기 위해 60-65%의$CH_4$ 와 30-35%의$CO_2$ 성분의 바이오가스를 50kW급 발전기에서 사용하였고 연소 후 배출되는 가스 성분을 분석하였다. -
Kim, Jae-Kon;Lee, Donmin;Park, Chunkyu;Lim, Eui Soon;Jung, Choong-Sub;Kim, Ki-Dong;Oh, Youngsam 174.1
Biogas production and utilisation is an emerging alternative energy technology. Biogas is produced from the biological breakdown of organic matter through anaerobic digestion. Biogas can be utilized for various energy services such as heating, electricity generation and vehicle fuel. Especially, to be utilized as vehicle fuel, raw biogas needs to be upgraded, that is, mainly the removal of carbon dioxide to increase the methane content, up to more than 95% in some cases, similar to the composition of fossil-based natural gas. Biogas fuelled vehicles can reduce$CO_2$ emission by between 75% and 200% compared with fossil fuels. Biomethane development is largely driven by national initiative and predominately by concerns for national air pollution and waste management. Recently, biogas projects for vehicle fuels by some companies are ongoing and Korea government also announced investment to develop biogas as a transport fuel. Therefore, the aim of this study is to examine the feasibility of biomethane as a transport fuel in Korea. In this study, we investigated quality characteristics, quality standard and upgrading technology to use vehicle fuel of transport sector in Korea. -
최근 유가상승과 석유, 천연가스의 가채 매장량의 한계등과 함께 온실가스에 의한 지구온난화 방지를 위하여 미국, 유럽국가 및 캐나다 등에서는 바이오매스를 이용한 에너지 회수 기술개발에 많은 관심과 연구를 수행하고 있다. 바이오 매스는 에너지 밀도 대비 존재하는 지역이 광범위하여 발생, 수집, 수송에 따른 비용이 많이 소요되는 특성이 있어 산지에서 직접처리하거나 수집하여 대규모처리등과 같이 여러 가지 현장상황에 따라 적정한 플랜트 운용의 유연성을 갖추고 있어야 한다. 일반적으로 바이오매스로부터 중소형으로 분산형 발전이나 수소제조를 위해서는 직접 연소법 보다는 가스화 방식을 이용하고 있는데, 연소에 의해 열을 생산하여 전기를 생산하는 방식은 스팀터빈을 이용하는 것이며, 스팀터빈은 소형 운용이 어렵기 때문이다. 본 연구에서는 폐목재로부터 합성가스제조를 위하여 5톤/일 규모 가스화기를 제작하였으며, 타르 및 수트와 같은 미반응 물질을 제거할 수 있는 집진, 세정장치를 설계 및 제작하였다. 또한 합성가스에 함유된 현열로부터 열회수를 위하여 열교환기를 설치하였으며, 정제된 합성가스를 이용하는 가스엔진을 통하여 열병합 발전시스템 연계운전을 수행하였다. 운전 실험을 폐목재 가스화 3톤/일 규모로 수행하였으며, 평균 1,500kcal/
$Nm^3$ 의 발열량을 갖는 합성가스를 생성시킬 수 있었다. 사이클론, 스크러버 및 기수분리 장치를 이용하여 정제된 합성가스는 합성가스 엔진을 통하여 72kW 이상의 전력생산이 가능하였다. 열교환기를 통하여 평균 15,000kcal/h의 배열 회수가 가능하였으며, 바이오매스 가스화 합성가스를 이용한 열병합 발전이 가능함을 입증하였다. -
우드칩을 포함하는 화석연료대비 발열량이 낮은 바이오매스를 가스화를 통하여 활용하는 경우 타르 및 수트를 포함하는 저열량의 합성가스가 생성된다. 이러한 합성가스를 엔진을 통한 발전, 스팀, 수소 및 화학제품 생산으로 활용하기 위해서는 고효율의 타르 정제 및 제거가 필수적이다. 특히 착화가 어렵고 연소온도 및 연소율이 낮으며, 화염구간이 좁은 저열량의 합성가스를 이용하여 스팀을 생산하기 위해서는 많은 문제점으로 인하여 기술 개발이 필요하다. 본 연구에서는 하향류식 가스화기를 이용하여 우드칩을 연료로 합성가스를 제조하였으며, 합성가스에 포함되어 있는 타르 및 수트와 같은 미반응 물질을 제거할 수 있는 집진, 세정장치를 설계 및 제작하였다. 특히 고효율 타르의 제거를 위하여 두 종류의 산화촉매를 이용한 합성가스 내 타르의 제거 연구를 수행하였다. Ru 촉매를 이용하는 경우 합성가스 내 타르의 농도를 100ppb 정도까지 저감이 가능하였다. 정제된 합성가스는 유류 혼소 버너를 통하여 보일러 연소실에서 혼합연소되어 30만kcal/h의 열을 공급함으로써 스팀을 생산 하였으며, 생성된 스팀은 블록 건조 시설에서 이용하였다.
-
바이오디젤의 국가별 의무 사용 정책 확대로 인해 원료유 가격이 상승하고 있으며 원료유가 부족한 상황으로 다양한 원료를 찾는 연구가 진행되고 있다. 육상 유지 작물보다 단위면적당 생산성이 매우 높은 미세조류는 제3세대 바이오매스로 주목받고 있으며 산업체 배출 이산화탄소를 이용해 작은 면적에서 배양할 수 있는 장점이 있다. 미세조류로부터 바이오디젤 생산은 먼저 오일 함량이 높은 미세조류 종의 선정과 배양 및 수확 후 효율적인 방법으로 바이오디젤 원료유를 추출하는 과정이 중요하다. 본 연구는 Microwave로 전처리된 미세조류로 부터 원료유를 추출하여, 인지질, 단백질, 엽록소 등의 반응저해 물질을 일부 감소시키고 추출수율을 높였지만, 산가가 80이상으로 높게 추출되고 추출된 오일이 높은 점성을 가지는 문제가 있다. 이로 인해 전이에스테르화 반응의 진행이 불가하였으며 이러한 문제를 해결하기 위해, 에스테르화 반응에 용매를 혼합하여 반응성을 개선하고자 하였다. 추가된 보조 용매는 오일과 쉽게 혼합되어 반응물의 점성을 낮추고, 반응 완료후, 물에 쉽게 용해되는 불순물, 미 반응물, 촉매 등의 분리 및 제거를 용이하게 하는 장점이 있다. 또한 오일과 비교하여 낮은 끓는점을 갖는 용매는 증류를 통해 쉽게 제거가 가능하다. 반응이 완료된 오일은 초기산가 80에서 10이하의 감소를 나타내 용매 혼합 에스테르화의 효율적인 부분을 확인하였다.
-
바이오디젤 대체 원료로서 폐돈지, 폐우지를 이용한 오일 추출 및 바이오디젤 생산 반응을 진행하고 이때 사용되는 과잉 메탄올의 회수 및 재사용에 관한 연구를 수행하였다. 추출된 오일의 상태에 따라 전처리를 위한 에스테르화 반응여부를 판단하게 되지만 에스테르화 반응과 전이에스테르화 반응 모두에서 상당량의 과잉 메탄올을 투입하게 된다. 에스테르화 반응에서는 이론량보다 20~50배 가량을 투입하고 전이에스테르화 반응에서는 오일:메탄올 이론 몰비인 3:1 보다 2~4배 가량을 이용하게 된다. 에스테르화 반응에 사용되는 촉매는 균질계 액체 산 촉매와 불균질계 고체 산 촉매가 이용될 수 있으며 본 연구에서는 황산을 이용한 에스테르화 반응을 실시하였으며 전이에스테르화 반응에서는 KOH를 촉매로 이용하였다. 각각의 공정에 사용된 과잉 메탄올의 재이용 방안을 조사하였으며 메탄올을 단증류를 통해 회수하는 방법과 회수된 메탄올을 이용한 에스테르화 반응 및 전이에스테르화 반응을 실시해 반응성을 조사하였다. 이를 통해 미반응 과잉메탄올의 회수 정제시 메탄올의 최대 수분함량(%) 허용치를 결정할 수 있었다. 회수된 메탄올을 재이용함에 따라 바이오디젤 생산비 중의 원료(메탄올) 및 설비비 절감이 가능할 것으로 판단된다.
-
피마자유(Castor oil)는 합성수지, 그리스, 유압용 오일, 윤활기유 등의 다양한 용도로 쓰이는 오일로서 점도가 높고 무색에서 황갈색을 띈다. 피마자유 추출은 압착 착유 또는 용매 추출로 얻게 되며 본 실험에 사용된 오일은 압착 착유한 것으로 매우 진한 갈색을 띄는 정제전 오일을 이용하였다. 실험에 사용된 피마자유의 초기 산가는 1mgKOH/g 이하로 낮은 유리지방산 함량을 보였으며 수분은 0.3%로 전이에스테르화 반응을 위해서는 수분 증발이 필요했다. 피마자유의 바이오디젤 생산을 위해 진행된 물성 분석 항목은 산가, 수분, 인함량, 황함량, 점도, 고형물이며 원료유와 그 바이오디젤에 대해 각각 물성 분석을 실시하였다. 피마자유의 가장 큰 특징은 다른 식물성 오일과는 다르게 오일이 알코올에 녹는 특성이 있으며 이런 이유로 전이에스테르화 반응 후 바이오디젤과 글리세롤이 분리되지 않는 문제점을 갖고 있다. 피마자유를 이용해 제조한 바이오디젤, 즉 지방산메틸에스터의 함량을 분석한 결과 약 90%의 메틸에스터화 반응 전환율을 나타내었으나 국내외 품질규격상의 탄소수 C14~C24:0의 지방산 에스터(fatty acid methyl esters)로 검출되는 바이오디젤의 함량은 10% 미만으로 나타났으며 나머지 90%는 라이신올레익산메틸에스터(ricinoleic acid methyl ester)로 분석되었다. 따라서, 기존의 대두유, 유채유, 팜유, 폐식용유로부터 제조한 바이오디젤과 물성이 매우 상이하고 특히 끊는점(boiling point)과 점도가 높아 경유 대체연료로는 활용이 불가능할 것으로 판단된다. 하지만 기존의 다양한 용도의 오일로 사용하기 위해 정제하는 과정에서 전체 착유 오일중의 약 10%만을 선택적으로 분리하여 바이오디젤 원료로 활용하는 방안은 가능할 것으로 판단된다.
-
국내 바이오디젤의 원료로 사용되는 식물성 오일은 거의 전량이 수입된 것으로 원료를 자급화 하기 위한 방안으로 국내 동물성 폐자원을 이용한 바이오디젤 연구가 활발히 진행되고 있다. 본 연구에서는 전자레인지를 이용해 동물성 폐자원인 폐돈지 및 폐우지로부터 오일을 추출 후 물성을 분석하고 전이에스테르화 반응을 진행하였으며 바이오디젤 제조 특성을 조사하고자 하였다. 전이에스테르화 반응에 사용되는 염기 촉매를 몇가지 선정하여 각각의 촉매에 따른 바이오디젤의 반응특성을 메탄올 양을 변화시키며 조사 실험하였다. 기존에 사용된 바이오디젤 제조 촉매는 KOH를 주로 사용하였으며 본 연구에서는 KOH, NaOH,
$NaOCH_3$ 를 촉매로 사용하여 오일질량 대비 0.8~1.2%의 촉매를 사용하였으며 메탄올의 양은 오일 몰수 대비 6:1~12:1의 비율로 사용하여 반응시간에 따른 반응특성과 제조 바이오디젤의 물성을 분석해 각 촉매에 따른 바이오디젤 생산 특성을 비교분석하였다. -
세계적인 자원고갈과 지구온난화와 같은 환경문제가 발생됨에 따라 대체에너지 개발에 대한 연구가 활발히 이루어지고 있다. 섬유소 기질을 이용한 바이오에탄올 생산은 세계적으로 막대한 자원이 있으며 광합성에 의해 재생산되는 무한한 재원으로서 환경적으로도 대기오염물질을 적게 배출하여 유용한 에너지원으로 각광받고 있다. 하지만 섬유소 기질은 cellulose, hemicellulose, lignin과 같은 고분자 화합물이 유기적으로 결합된 단단한 결정구조로 이루어져 있어 이를 분해하여 원하는 물질을 얻기 위해서는 전처리 과정이 필요하다. 전처리 공정은 바이오에탄올을 생산하는 당화 및 발효공정의 효율 및 반응시간 단축에 기여하며, 특히 섬유소 기질일 경우에는 필수불가결한 공정이다. 전처리 공정은 물리적, 화학적, 생물학적 방법으로 나누어지며, 이러한 방법들 중 기질의 특성과 처리효율에 따라 기술들을 병합하여 사용하기도 한다. 이에 본 연구에서는 산 처리, 암모니아 처리, 과산화수소 처리 및 효소를 이용한 생물학적 처리를 단독 또는 병행하여, 전환된 당 성분 및 함량을 조사함으로서 섬유소계 기질인 채소 음식물류 쓰레기를 대상으로 바이오에탄올을 경제적으로 생산하기 위한 적합한 전처리법을 검토하였다. 전처리 방법별 당화율을 살펴보면, 산 처리와 암모니아-과산화수소-계면활성제 처리가 각각 65.3 % 및 65.7 %로 가장 높았으며, 과산화수소 처리는 16.2 %로 가장 낮았다. 반면 전처리 공정 없이 효소를 이용한 당화만을 실시한 경우에는 4.3 %의 낮은 당화율을 나타내었다. 섬유소계 기질의 전처리 효율을 향상시키기 위해 첨가하는 계면활성제의 효과는 암모니아-과산화수소 및 암모니아-과산화수소-계면활성제 처리의 당화율을 비교한 결과, 뚜렷한 효과를 확인할 수 없었다. 전처리 방법별 당의 성분 및 함량을 비교한 결과 육탄당은 암모니아-과산화수소-계면활성제 전처리에서 가장 많이 검출되었다. 오탄당은 산 처리 후 그 함량이 현저히 높았으며, 오탄당 중 xylose의 함량이 60.49 mg/g로 가장 많이 차지하고 있었다. 이 결과로부터 전처리 방법에 관계없이 당화율은 유사한 수준을 보이지만, 당화된 당의 성분 및 함량에는 큰 차이가 있음을 알 수 있었다. 이당류의 경우 과산화수소 및 암모니아-과산화수소 처리를 제외한 나머지 전처리 방법에서 유사한 수준을 나타내었다. 암모니아 처리 및 과산화수소 처리를 순차적으로 병행한 암모니아-과산화수소 처리에서는 각각의 처리시보다 육탄당의 함량은 증가하였으나 암모니아 처리시보다 이당류의 함량은 감소한 것으로 나타났다.
-
DME is generally expected to be used as a promising clean alternative fuel to diesel fuel. DME is not natural product but a synthetic product that is produced either through the dehydration of methanol or a direct synthetic from syngas. As DME has no carbon-carbon bond in its molecular structure and is an oxygenate fuel, it's combustion essentially generates no soot. DME has such cetane number of 55~60 that it can be used as a diesel engine fuel. However, DME has low lubricity but a proven method to solve the poor lubricity is by adding lubricity improver. Therefore, the aim of this study is to develop lubricity improver of DME as a transport fuel in Korea. In this study, we investigated a possibility of fatty acid ester compounds as a candidate to improve DME lubricity as compared with current lubricity improver of diesel. We also evaluated quality characteristics, storage stability of DME with lubricity additives.
-
바이오디젤이란 식물성 기름, 동물성 지방, 폐식용유 등의 재생 가능한 자원을 촉매 존재 하에 알코올과 반응시켜 생성되는 에스테르 혼합물을 말하며 경유와 물성이 유사하므로 경유에 혼합하여 압축착화 방식인 디젤엔진에 사용할 수 있다. 그러나 바이오디젤은 경유에 비하여 탄소-탄소 간 이중결합을 가지고 있는 성분을 많이 함유하고 있기 때문에 공기에 의해 산화가 일어나기 쉽다. 일반적으로 폐놀계 향산화제인 t-buthylhydroquinone(TBHQ)를 사용하여 산화안정성을 향상시키나 국내에서 사용되는 산화방지제는 전량 수입에 의존하고 있어 제품 개발에 의한 국산화가 시급한 실정이다. 본 연구에서는 폐유지로부터 생산한 바이오디젤의 산화안정성 향상을 위하여 폐놀 및 아민계 등의 산화방지제를 합성하여 바이오디젤에 적용하였으며, 다양한 물성시험방법을 적용하여 석유 및 석유대체연료 사업법에서 규정하는 바이오디젤의 품질기준을 확인하였다. 또한 EN 14112 바이오디젤 산화안정성 시험방법으로 폐놀 및 아민계 등의 산화안정성을 확인하였다. 본 연구는 산학연 공동기술개발 1차년도 사업으로 한국화학연구원과 공동으로 수행하였으며, 산화방지제 적용평가를 통해 우수한 제품을 선정하여 2차년도에는 차량 테스트를 통해 연료 첨가제로서의 적합성을 검증할 예정이다.
-
Bark, Surn-Teh;Koo, Bon-Cheol;Choi, Yong-Hwan;Moon, Youn-Ho;Ahn, Seung-Hyun;Cha, Young-Lok;Kim, Jung Kon;An, Gi Hong;Suh, Sae-Jung;Park, Don-Hee 179.1
Pretreatment of cellulosic biomass is necessary before enzymatic saccharification and fermentation. The objective of this study was to evaluate the effect of combined aqueous ammonia-dilute sulfuric acid treatment on cellulosic biomass. Miscanthus was pretreated using aqueous ammonia and dilute sulfuric acid solution under high temperature and pressure conditions to be converted into bioethanol. Aqueous ammonia treatment was performed with 15 %(w/w) ammonia solution at$150^{\circ}C$ of reaction temperature and 20 minutes of reaction time. And then, dilute sulfuric acid treatment was performed with 1.0 %(w/w) sulfuric acid solution at$150^{\circ}C$ of reaction temperature and 10 minutes of reaction time. The compositional variations of this combined aqueous ammonia-dilute sulfuric acid treatment resulted in 68.0 % of cellulose recovery and 95.7 % of hemicellulose, 81.3 % of lignin, 89.1 % of ash removal respectively. The enzymatic digestibility of 90.5 % was recorded in the combined pretreated Miscanthus sample and it was 14.7 times higher than the untreated sample. The ethanol yield in the Simultaneous Saccharification and Fermentation was 90.4 % of maximum theoretical yield based on cellulose content of the combined pretreated sample and it was about 98 % compared to the${\alpha}$ -cellulose ethanol yield. -
바이오매스 가스화 프로세스 개발에 있어서 가장 기본적인 해결과제는 고발열량의 합성가스 제조, 냉가스 효율의 향상, 타르 발생량 저감 및 제거이다. 가스화 효율 향상에 대한 연구는 국내외 적으로 많이 이루어지고 있으나, 타르 발생량 저감에 대한 연구는 많이 이루어져 있지 않다. 타르는 분자량이 큰 방향적 탄화수소로 응축되면 점성이 높아 배관폐쇄, 정제설비의 압력손실 증가로 인해 운전정지 및 가스화율 저하의 원인이 된다. 가스화로에서 타르 발생량을 저감시키는 방법 중에는 Ni계 촉매를 이용하는 방법이 있으나, 카본 누적에 의한 활성저하, 알칼리금속에 의한 응집 등의 문제가 발생할 수 있다. 한편 철산화물은 합성가스 중의 C2-C3계의 타르를 분해하는데 효과가 알려져 있다. 따라서 본 연구에서는 적벽돌, 염색슬러지 회재 등에는 철산화물이 다량 함유되어 있는 것에 착안하여 폐기물중의 폐금속을 이용한 바이오매스 가스화에 대한 연구를 수행하였다. 점토광물계 폐기물인 적벽돌 파쇄물(
$SiO_2$ 67.2%,$Al_2O_3$ 19.7%,$Fe_2O_3$ 8.7%,$K_2O$ 2.0%,$TiO_2$ 1.2%, MgO 0.7%)을 전처리 한 후 유동매체로하여 우드펠렛을 가스화한 결과, 가스 생성량이 증가하고, 타르 및 탄화수소류가 감소하는 경향을 나타내었다. 특히 타르는 후단의 타르 트랩에서 타르가 거의 검출이 되지 않았다. 전처리를 하지 않은 적벽돌 파쇄물은 반응시간이 경과한 후에 가스화율이 증가함에 따라 철화합이 가스화로내에서 환원되어 타르를 분해하는데에는 어느 정도의 반응시간이 필요한 것을 확인하였다. -
본 연구는 중 소규모 매립지가스(LFG)의 활용을 위한 가스고체화(Gas-To-Solid) 기술개발을 목적으로 하고 있다. LFG는 환경적인 문제로 인하여 소각 등의 방법으로 처리하고 있으나, 약 5,000kcal/
$m^3$ 의 높은 발열량과 일반적으로 매립 후 20~30년 후까지 지속적인 발생특성으로 안정적인 공급이 가능한 신재생에너지원으로 활용될 수 있다. LFG 자원화 할 경우 발전 및 중질가스 등으로 활용하는 것이나, 중소규모 매립장의 경우 경제성 등의 문제로 자원화하지 못하고 태워지거나 방치되고 있다. 본 연구에서는 LFG의 저장과 수송 기술 중 GTS 기술을 통하여 저장과 수송에 제약이 크고 많은 비용이 소비되는 기체 상태의 에너지원을 하이드레이트화 시킴으로서 중 소규모 매립지에서 상대적으로 적은 비용으로 가스저장과 지상수송이 가능하게 할 수 있다. 본 연구의 결과로 LFG 에너지화 실증화 플랜트를 설계/제작 하였으며, 메탄+이산화탄소+물 하이드레이트 형성 실험을 통해 4.56 Mpa, 277.2 K 조건에서 3시간을 한 사이클로하는 공정운전을 가지는 것을 확인하였다. -
Yoon, Hyungchul;Cho, Sangsoon;Kang, Sukju;Kim, Jinhoon;Kim, Kyongtae;Ko, Daekwun;Lee, Sihun;Han, Gwangchun 185.2
1900년대 이후 산업발전에 따른 인구의 도시 집중화로 인한 하수량 증가에 따라 하수슬러지 발생량이 점차 증가하게 되면서 하수슬러지 처리에 관한 문제 등이 제기되기 시작하였다. 국내의 경우 2003년 하수슬러지의 매립이 금지된 후, 발생슬러지 대부분을 해양투기 등을 통해 처리하여왔다. 2009년 기준으로 국내에서 발생되는 하수슬러지량과 처리 분포를 살펴보면 전국 433개소 하수처리장에서 1일 평균 8,295톤(3,028천톤/년)이 발생되고 있으며, 이 중 47%가 해양투기 되고 있는 실정이다. 그러나 해양투기마저도 런던협약'96의정서 가입으로 2012년부터 금지됨에 따라 국내에서는 슬러지처리 및 재활용 방안과 관련한 연구개발이 활발히 진행되고 있는 중이다. 하수슬러지 처리 및 재활용기술의 경우 다양한 공법 등이 개발 중에 있으나 설비의 불안정 및 높은 투자비 등으로 인해 아직까지 상용화 된 설비 등은 많지 않은 실정이다. 이에 따라 본 연구에서는 POSCO 건설에서 개발한 슬러지 연료화 기술을 통해 생산된 슬러지 탄을 석탄 화력발전소 등에 석탄 보조연료로 활용할 수 있는 방안을 강구하여 상용화 가능한 혼소 기술을 개발하고자 하였다. 슬러지탄(발열량 3.000kcal 이상)을 석탄 화력발전소 보일러에 일정 비율로 혼소하여 슬러지탄의 품질평가, 중금속 용출시험 및 함량분석, 잔재물의 중금속 용출시험 등을 실시하였으며, 그 결과 모든 시험항목에서 연료화 관련 법적기준을 만족하는 것으로 나타났다. 슬러지탄을 화력발전소에 혼소하여 사용할 경우, 2012년부터 시행예정인 RPS(Renewable Portfolio Standard)법 대응 및 석탄사용량 저감 등을 통한$CO_2$ 저감으로 저탄소 녹색성장의 자원순환사회를 구축하는 데 이바지 할 것으로 판단된다. -
Most of waste plastics including waste vinyls have been recycled up to about 50% of waste production, 4.5 million ton per year in 2009. To fundamentally increase the recycled amounts of waste plastics to waste production, the energy utilization of waste plastics is inevitable. But the contents of PVC included in waste plastics can limit the use as a RPF and make the air pollutants such as HCl and dioxin when it burns in the combustion system. Accordingly the source dechlorination by using heating method can be applied to make low contents of HCl as less than 0.6%. In this study the twin screw reactor using heat medium was used for the source dechlorination. As results of study, it was considered that this system is effective for the industrilal application.
-
RDF 연료의 열이용은 2003 폐플라스틱 고형연료 사용에 관한 고시가 나온이후 생산과 이용이 꾸준히 증가하는 추세이며 최근에는 원주, 대구, 부산 등 각 지역의 RDF 생산시설 구축 및 열병합 보일러 건설사업의 추진으로 더욱 활발하게 진행되고 있다. 본 연구는 순환유동층 시범 연소로에서 RDF를 전용으로 연소하여 그 연소특성을 고찰하고 상용 보일러 설계를 위한 연소자료를 축적하는 데 있다. 본 연구는 실험을 위하여 자체로 건설한 순환유동층 보일러에서 수행하였다. 연소 연구에서는 연소특성과 더불어, 환경기술과 연소로의 부식방지에 관한 기술을 고찰하였다. 보일러의 스팀사양은
$300^{\circ}C$ 와 15ata 이상으로 하였다. 설치된 보일러는 장시간의 운전과 반복 실험을 통해 상용 규모 보일러의 설계에 적용할 연소자료를 확보하였다. 또한 연료특성을 파악하기 위하여 국내에서 생산되는 RPF와 RDF 각 일종을 입수하여 성분을 분석하고 그 특성 자료를 비교하였다. RDF는 순환유동층 보일러에서 뛰어난 연소 효율을 나타내었으며 배연특성도 연소하는 동안 일정하게 배출되었다. 온도나 압력등 연소 변수는 RDF는 연소실험 동한 안정적인 값을 나타내었다. 대부분의 배연물질은 환경기준을 충족할 수 있었다. 다만 HCl의 배출 특성은 환경 규제치를 넘어 섰으며 별도의 배가스 처리기술을 적용하여 환경기준을 맞출 수 있었다. -
RDF(Refuse-Derived Fuel) is a fuel of pelletized form made of combustible solid wastes and can not only be used as alternative energy to fossil fuel but also solve troubles in thermal uses of incinerator. As the first stage for obtaining elementary data required to develop criteria of raw materials appropriate to RDF combustion facilities actively spread recently in Korea, preliminary experiments were conducted on CO, SOx, NOx and HCl production and reduction characteristics in combustion of RDF. RDF samples weighing 2~3 g per a sample were manufactured in a lab-scale way and combustion tests of RDF were carried out in electric furnace with quartz tube of 50 mm inside diameter.
-
태양광산업의 value chain중 up-stream쪽인 고순도 실리콘산업은 셀, 모듈, 시스템 쪽에 비하여 영업 이익률이나 부가가치 측면에서 매우 높은 성장성을 현재 보여주고 있으며 최근 원자력산업의 안전성 문제가 대두됨으로 인하여 태양광수요가 전 세계적으로 증대되는 경향을 나타내어 태양광용 실리콘의 수요가 확대됨과 아울러 spot시장에서의 가격 또한 상승하고 있다. 이런 관점에서 잉곳 및 웨이퍼 가공 중에 발생하는 고순도 실리콘 폐기물의 재활용 이 다시 주목받고 있다. 태양전지 웨이퍼(wafer)용 소재는 6N급 이상의 결정질 실리콘 잉곳(ingot)이 주를 이루며, 고효율의 셀을 제조하기 위해서 단결정 실리콘 잉곳이 많이 사용된다. 실리콘 단결정을 육성하는 방법에는 Floating zone 법, Czochralski 법, Bridgeman 법, CVD 등 매우 다양하다. 이 중 Czochralski 법은 전체 생산량의 대부분을 차지하고 있는 방법으로, 용융액에서 결정을 인상하여 ingot을 제작하는 방법이다. 그러나 대량의 전기에너지를 소비하여 제작되는 고순도의 실리콘 단결정 잉곳은 후 가공공정에서 그 절반 이상이 분말(powder) 및 슬러지(sludge)로 폐기되므로, 자원의 재활용 및 환경오염 측면에서 주요과제가 되고 있다. Czochralski 법으로 제작된 ingot의 경우 그 표면이 매끄럽지 못하여, 웨이퍼 단위의 가공 시 형태가 진원이 될 수 있도록 표면을 미리 연마(grinding)하는데, 이때에도 미세 분말이 다량 발생하게 된다. 본 연구에서는 이러한 고순도 단결정 실리콘 ingot의 연마 가공공정에서 발생한 미세 분말을 용해하여 보았다. 진공 챔버(chamber) 내부에 유도가열 코일과 냉도가니로 구성된 장비를 통해 전자기유도가열을 이용하여 실리콘 분말 폐기물을 용해하고, 그 시편을 ICP-MS 및 비저항 측정을 통해 분말 의 특성을 조사하여 재활용 가능성을 검토해 보았다.
-
0.5 ton/day 용량의 장비를 이용하여 초음파와 고전압 단독 처리에 의한 슬러지 용존화율을 조사하였다. 또한 초음파와 고전압을 병행한 방법에 의한 슬러지 용존화율을 조사하였다. 그 결과 초음파와 고전압을 개별적으로 적용하였을시 나타나는 슬러지 용존화율 보다 이 둘을 병행하여 함께 처리했을 시에 나타나는 슬러지 용존화율에 기대 이상의 상승효과가 있는 것을 알 수 있었다.
-
The use of renewable energy sources is becoming increasingly necessary to minimize the problems derived from the global warming impacts caused by the utilization of fossil fuels as well as their limited supply and reservoir. Also, localized heavy rain has occurred in many areas. As a result, suspended wood waste is being inflow into the dam and the problem of waste disposal has occurred. It is a unique renewable and alternative source for the production of energy. The experiment using wood waste (dry weight 25.0g) was conducted for extraction sugars such as xylose, lactose and glucose. For the sugar extraction from wood waste, hydrolysis experiment using wood waste was conducted by two steps. First step was reacted with 72% sulfuric acid (24.0N and 37.5 ml) for 1hr at
$30^{\circ}C$ and second step was reacted at$105^{\circ}C$ for one hour after adding 2.45times of hot water. Extracted sugar was used in the experiment of sugar consumption to estimate feasibility of ethanol production using yeast(P. Stipitis and S cerevisiae). As a result, sugar extracted from wood waste was effective consumed by yeast(P. Stipitis and S cerevisiae). The consumption rate by yeast was S. cerevisiae was faster than that of P. stipitis. It can be confirmed that resource as ethanol production using wood waste was available. -
Global warming effect was intensified due to rapid growth of fossil fuel consumption caused by urbanization and industrialization. Various efforts was being done to solve the problems leading to anomaly climate such as flood, downpour, heavy snow. As a results of international efforts for management of global warming, Kyoto Protocol, which was passed in Kyoto, Japan in 1997, designated
$CO_2$ ,$CH_4$ ,$N_2O$ , HFCs, PFCs,$SF_6$ as a global warming gases. And IPCC(Intergovernmental Panel on Climate Change) suggested IPCC guideline for systematic establishment of national greenhouse gas inventory. Among five categories in IPCC guideline, the representative emission source of waste category is SWDS(solid waste disposal site). The concentrative research should progress for effective management of greenhouse gas related with waste. In this study, Tier1 and Tier2 methods which was suggested by 2006 IPCC(Intergovernmental Panel on Climate Change) guideline, was used to predict methane generation from C sanitary landfill located in Chungju area. To predict methane generation from C sanitary landfill, all factors were defaults values that were provided by 2006 IPCC guideline and Korea emission factors for Tier1 and Tier2 method. And economics of generated methane was estimated. From the predicted result using IPCC guideline, the methane generation was persistingly increased over a 9-year period(2000 ~ 2008). Aggregated amount of methane generation was about 3,017ton and 3,170ton predicted by Tier1 and Tier2, respectively. From the results of estimated economic value gained by generated methane from the C sanitary landfill for ten years from now(2010 ~ 2020), the profit was about 2.39 ~ 2.76 hundred million won. -
매립가스(LFG)는 약 50v/v% 이상의 메탄가스로 이루어져 있어 LFG의 자원화 사업은 국내 신 재생에너지를 이용한 발전사업 중 태양광사업 다음으로 활발히 진행되고 있다. LFG의 대표적인 활용기술로는 가스엔진, 가스터빈 및 증기터빈을 이용한 발전과 중질가스 및 고질가스 형태의 연료로 생산하는 방식 등이 있으며 이러한 분야에 매립지가스를 적용하기 위해서는 장치 부식의 주 원인이 되는 황화수소 가스의 제거가 반드시 이루어져야 한다. 본 연구에서는 황화수소 제거를 위해 하이드레이트와 마찬가지로 동공을 형성하여 가스의 포집과 저장이 가능한 하이드로퀴논(HQ)을 이용하고자 한다. HQ은
$0^{\circ}C$ 부근에서 해리되는 하이드레이트와 달리 상온에서 고체 형태로 구조를 유지할 수 있어 가스의 포집 및 저장에 용이한 장점이 있다. 메탄, 이산화탄소, 황화수소 혼합가스에서 황화수소 90% 이상 제거를 목적으로 HQ와 반응시켜 동공 내에 이들 가스의 포집여부를 확인하였다. -
본 연구에서는 지열히트펌프 시스템의 열원으로써 지열이외에 건축물의 미활용 에너지라고 할 수 있는 상수도의 에너지를 활용하여 지중열교환기의 천공길이를 줄이는 것이 주요 목적이며, 또한 건물의 미활용에너지를 냉난방에너지원으로써 이용 가능한 것을 보여주는 것에 있다. 실험은 4인 가족기준으로 3RT 용량의 히트펌프를 설치하고 인당 평균 177 liter/day 기준으로 하루에 약 710 liter/day의 물을 사용하는 것으로 가정하였다(환경부 2007년 상수도 통계값). 시간당 가정내에서 사용하는 물량은 일정하지 않아 일일 8시간 사용하는 것으로 하여 약 1.5 LPM 으로 실험하였다. 저수조의 크기 및 지열 히트펌프의 열원으로써 사용가능한 열량을 계산하기 위해 CFD 시물레이션을 수행하였다. CFD의 결과 상수도를 급수하기 위한 저수조의 크기는
$2m^3$ 로 결정하였으며 이때 열원으로써 사용가능한 열량은 약 0.7RT였다. 48시간의 실험기간 동안 저수조를 통해 얻은 열원은 0.6RT 였으며 100m의 지중열교환기를 통해 얻은 열원은 2RT 였다. 히트펌프 자체의 난방 COP는 평균 4.2를 나타내었으며 펌프등의 소비전력을 포함한 System COP는 4.0 나타내었다. 이번 연구를 통해 건물의 미활용에너지인 저수조의 물을 이용하여 지열히트펌프의 열원으로써 이용 가능하며 기존의 지열히트펌프 시스템대비 천공길이 단축, 시공비 저감이 가능한 것을 볼 수 있었다. -
Heating and cooling performance has been analyzed for the water-source heat pump system using raw water from Daechung reservoir. During heating operation from March to May, water temperature is not good condition for a heat source due to the higher atmospheric temperature. Avearged heating load ratio is only 14.3%, and the averaged unit COP and system COP are estimated to be 2.46 and 2.15 respectively. The COP is affected considerably by the water temperature, and the unit COP is increased from 2.16 at
$5^{\circ}C$ to 2.95 at$11^{\circ}C$ . Cooling performance is analyzed with the measured data from June to August. During cooling operation, raw water has lower temperature by 4.$5^{\circ}C{\sim}4.7^{\circ}C$ than the atmosphere. The load ratio is 39.2%, and the averaged unit COP and system COP are estimated to be 7.25 and 6.13 respectively. The heating COP is affected by the load ratio rather than water temperature. The COP is increased for 20%~40% load ratio, while is decreased for 40%~60% load ratio. It is estimated that the compressor operation combination for 3 (two constant speed and one inverter) compressors is changed for the load ratio. -
This paper presents an experimental study on a new potential geothermal energy source obtained from tunnel structures. An "energy textile", which is a textile-type ground heat exchanger, was fabricated between a shotcrete layer and a guided drainage geotextile in the tunnel lining system. To examine the long-term thermal behavior of the energy textile, the difference in temperatures of the inlet and outlet fluid circulating through the heat exchange pipe within the energy textile was monitored using a constant-temperature water bath. Daily heat exchange rate of the energy textile during cooling operation was estimated from the measured temperatures of the inlet and outlet fluid through the energy textile. The air and ground temperature was also continuously monitored. The operation of the energy textile as a ground heat exchanger was simulated using a 3D numerical CFD model (Fluent). The thermal conductivity of shotcrete and concrete lining components and temperature variation of air in the tunnel were incorporated in the model. The numerical analysis shows a good agreement with the long-term monitoring result.
-
The borehole heat exchanger of Geothermal Heat Pump (GHP) system should be sustainable and cost effective for long term operation. To guaranty the performance of the system thermal Response Tests (TRTs) with simple recommended procedures have been applied in many countries. Korea government developed a standard TRT procedure in order to control the quality on GHP projects. In the TRT procedure interpretation method has a rule that data set has to be interpreted by the line source model(LSM). The LSM employes some assumptions that surrounding medium is homogeneous and the line source is infinite and constant heat flux, however real ground condition is unisotropic and heterogeneous, and showing regional or local ground water flows in many cases. We need to develope improved evaluation models to estimate accurate ground thermal conductivity with respect to geological and influence of ground water because current TRT standard test procedure has limitations to be applied for every locations and system. This study surveyed the uncertainty of the thermal parameters from the interpretation method considering different evaluation period. The interpretation of 208 TRT data sets represents limitations of LSM application that some obtained ground thermal conductivities are statistically unstable and convergence time of ground thermal conductivity over test period shows trends responding the length of test period. This evaluation study will be helpful to provide some effective procedure for the thermal parameter estimation and to complement current TRT standard procedure.
-
In this study, a test bed was constructed in order to evaluate thermal efficiency of the energy pile which carries out combined roles of a structural foundation and of a heat exchanger. The energy pile in this study is designed as a large-diameter drilled shaft equipped with the heat exchange pipes which configures a W-shape and an S-shape. The drilled shaft reached to the depth of 60 m whilst the heat exchange pipes were installed to about 30 m deep from the ground surface. The W-shaped and S-shaped heat exchange pipes were installed in the opposite sections of the same drilled shaft. In-situ thermal response tests were performed for both the shapes of heat exchange pipes. To avoid underestimating the thermal performance due to hydration heat of concrete inside the drilled shaft, the in-situ thermal response tests for the energy pile were performed after four weeks since the installation of the energy pile.
-
Yoon, Woon Sang;Lee, Tae Jong;Min, Ki-Bok;Kim, Kwang-Yeom;Jeon, Jongug;Cho, Yong-Hee;Song, Yoonho 196.2
지구온난화와 화석연료 고갈에 대한 우려로 전세계적으로 신재생에너지의 개발 및 활용이 본격화되고 있다. 특히, 다양한 신재생에너지원 중에서 날씨 및 계절에 의한 영향, 기저부하 담당, 지상 점유 면적, 소음 등 생활환경 영향, 경제성 등을 고려할 때 지열에너지는 미래 청정에너지원로서 기대와 관심이 집중되고 있다. 화산이 존재하지 않는 우리나라에서의 지열발전은 거의 불가능한 것으로 인식되어 지금까지의 심부 지열에너지 개발 프로젝트는 대부분 지역난방, 시설영농 등 직접이용을 목표로 추진되어 왔다. 그러나, 2003년부터 한국지질자원연구원에서 수행한 포항 심부지열에너지 개발사업의 결과로 얻어진 다양한 지질학적/지열학적 증거들을 토대로 분석한 결과, 국내 일부 지역에서는 지하 5 km 심도에서 최대 약$180^{\circ}C$ 의 지온이 예상되어 국내에서도 심부 지열에너지를 이용한 지열발전에 대한 가능성이 제기되어 왔다. 여기에, 유럽과 미국 그리고 호주 등 선진국을 중심으로 비화산 지역에서 지하 심부에 인공적으로 지열저류층(파쇄대)을 생성하고 이를 통해 열매체(물)를 순환시킴으로써 생산된 증기를 발전에 활용하는 EGS (Enhanced Geothermal System) 기술이 개발되고 몇몇 성공사례가 발표되었다. 또한, 이러한 기술개발에 힘입어 EGS 지열발전에 대한 선진국의 과감한 연구비 투자가 이어졌다. 이러한 기술적 배경에 발맞추어 우리나라에서도 2010년 12월에 EGS 지열발전 과제가 착수되었다. 이 프로젝트는 아시아에서는 최초로 수행되는 EGS 기술 개발과제로서 2015년까지 약 480억원의 R&D 예산을 투입하여 MW급의 지열발전 pilot plant의 구축을 목표로 하고 있다. 프로젝트가 성공적으로 추진될 경우 국내외적인 파급효과는 매우 클것이다. 특히 2015년까지 1.5 MW의 pilot plant의 구축이 성공적으로 추진될 경우 국내에서는 2017년까지 3 MW 이상, 2020년까지 20 MW이상, 2030년까지 200 MW 이상의 지열발전이 가능할 것으로 기대된다. 또한 축적된 기술개발 경험을 바탕으로 인도네시아, 필리핀 등의 해외의 지열발전 사업에도 진출할 수 있는 계기가 될 것이다. 프로젝트는 넥스지오를 주관기관으로 하고 한국지질자원연구원, 한국건설기술연구원 및 서울대학교 등의 지질자원 관련 연구 및 교육기관과 포스코, 이노지오테크놀로지 등의 산업체가 참여하여 컨소시엄 형태로 추진하고 있으며, 향후 관심있는 여러 기관 및 산업체의 지원과 참여를 기대한다. -
2010년 12월에 착수한 인공 지열 저류층 생성기술(EGS)를 이용한 지열발전 pilot plant 프로젝트에서 계획된 5 km 깊이의 doublet 시스템에서 실현 가능한 발전량 목표를 추정하였다. 지하 5 km 에서의 암반 온도는 경북 포항지역의 평균 지온증가율은
$33^{\circ}C$ /km로 하였을 때 지표온도를 감안하면$180^{\circ}C$ 로 추정된다. 암반과의 열교환을 통해 생산되는 지열수의 온도를$160^{\circ}C$ , 발전 후 주입수의 온도를$60^{\circ}C$ 로 생각할 수 있고, 이때 binary 발전의 열효율은 0.11이 가능하다. 최근의 EGS에서 실현 가능한 생산 유량인 40 kg/sec을 가정한다면 총 발전량은 1.848 MW로 계산되며, 지열수 양수 펌프와 binary 발전의 냉각에너지 소요량을 고려하면 순 발전량 1.5 MW가 가능해진다. -
Preliminary analysis on the modeling conditions and the simulation results is conducted only to evaluate the correctness of the simulation configuration further to apply for the LASGIT project. Except for the unrealistic modeling conditions for the relations of capillary pressure and relative permeability against water saturation used previously, the simulation results successfully demonstrate Helium propagation typical for two-phase flow. Further elaborated simulation with more realistic parameters should complete the weak points of the preliminary work.
-
Underground air is a special energy source in Jeju and distributes lava cave, pyroclastic, open joint, and crushing zone. A possible area to utilize underground air is 85% of Jeju except to the nearby area of Sambang Mt. and 25m high coastal area from sea level. In Jeju, underground air is used for heating agricultural facilities such as greenhouse cultivated mangos, Hallbong and mandarin orange, pigsty, mushroom cultivation house, etc. and fertilizing natural
$CO_2$ gas by suppling directly into agricultural facilities. But this heating method causes several problem because the underground air has over 90% relative humidity and is inadequate in heating for crops. Mangos are the most widely grown tropical fruit trees and have been cultivated since 1993 in Jeju. In Jeju, the cultivating area is about 20ha and amount of harvest is 275ton/year in 2010. In this study, the heat pump system using underground air as heat source was installed in mangos greenhouse which area is$495m^2$ . The capacity of heat pump system and heat storage tank was 10RT, 5ton respectively and heating effect and heating performance of the system were analysed. -
This study was carried out in order to estimate the greenhouse performance for Ground filtration water source heat pump which was installed for supplying the heat to the paprika greenhouse in Jinju city. Experimental area of Greenhouse was
$3,300m^2$ , For keeping the heat from greenhouse, single plastic covering and double thermal screen was installed. With considering all of greenhouse insulation condition and designed heatng temperature, heating capacity for experimental greenhouse was calculated as 320,000kcal/hr. Coefficient of performance(COP) of Ground filtration water source heat pump was gauged and greenhouse heating performance was tested from Febuary 1 to Febuary 28 in 2011. The result showed that COP of heat pump was in the range of 3.7~4.7 and COP of heating system was in the range of 3.0~3.5. The vaule of COP was very high and the temperature inside greenhouse was well corresponded to the setting temperature of greenhouse environment controlling system. lots of Ground filtration water made the the number of well fewer and the expense for installing heating system cheaper than that of geothermal system used custmarily. and this system went beyond the limitation of intaking amount of groundwater in normal Groundwater source heat pump. -
Ground heat exchanger is the most important part which than 14% of the cost of construction and the performance of Ground heat exchanger is depended on it. Grout is inserted into the hole to the ground fixed and serves to enhance the thermal conductivity. So the research and development is needed. We were using cement grout. The result of the test thermal conductivity is 3.14 W/mK. It is much better than the existing grout is the thermal conductivity. The developed materials was examined by applying the grout in the field.
-
A water-source heat pump system has been developed for cooling and heating of a green house on the waterfront in Jinju. In order to supply a heat source/sink of water in alluvium aquifer to the heat pump system, the riverbank filtration facility (two pumping wells and one recharge well) for water intake and injection has been constructed. To pump and recharge water sufficiently, the geometric design such as depth and diameter for the wells have been completed, and details of the well such as slot size and length of the screen and filter pack size have been designed based on the practical and theoretical design method including D30 technique. For the investigation of the hydrogeological characteristics, step-drawdown test, long-term pumping test, and recovery test have been carried out for two developed pumping wells. Step-drawdown test has been performed on 4 step flowrates of 150, 300, 450,
$600m^3$ /day for 1 hour, and long-term pumping test on flowrate of$500m^3$ /day for 24 hours, and recovery test for 6 hours. Since the underground water filtrated by riverbank is flowing smoothly into the well, the water level goes down slightly for the long-term test. Consequently, the stable pumping flowrate for two pumping well has been predicted at least over$1,647m^3$ /day which is larger than the flowrate of$1,000m^3$ /day for a 60 RT heat pump system. -
This study concerns a low head and kaplan turbine efficiency measurement using the acoustic scintillation flow meter(ASFM). The ASFM is one of absolute discharge measurement methods because it measures velocity-area of discharge with couples of transducers. This study shows that the highest efficiency of turbine is 87.7% and the efficiency is 85.8% in the rated output(600kW). The test result is reliable because the efficiency trend from this test is similar to the result of index test conducted in 1986. In this paper, the principle, measurement methods, application and test procedures of the test are discussed.
-
Micro hydraulic turbines take a growing interest because of its small and simple structure as well as high possibility of applying to micro and small hydropower resources. The differential pressure exiting within the city water pipelines can be used efficiently to generate electricity like the energy generated through gravitational potential energy in dams. In order to reduce water pressure at the inlet of water cleaning centers, pressure reducing valves are used widely. Therefore, pressure energy is wasted. Instead of using the pressure reduction valve, a micro counter-rotating hydraulic turbine can be replaced to get energy caused by the large differential pressure found in the city water pipelines. In this study, in order to acquire design data of counter-rotating tubular type micro-turbine, output power, head, and efficiency characteristics due to the diffuser.
-
Recently, various developments in the area of small hydropower have being made and small hydro turbines are suitable for domestic use because it is a clean and renewable energy source. A small hydropower generator produces power by using the different water pressure levels in pipe lines and energy which was initially wasted by use of a reducing valve at the end of the pipeline is instead collected by a tubular-type hydro turbine in the generator. In this study, in order to acquire the performance of tubular-type hydro turbine applied, the output power, head, efficiency characteristics due to the different guide vane and runner vane angle are examined in detail. Moreover, influences of pressure and velocity distributions with the variation of guide vane and runner vane angle on turbine performance are investigated by using a commercial CFD code.
-
Domestic hydroelectric power plants has been manufactured as the design condition by the demand. Hydraulic turbine power plants operating at appointed load shall be operate stable in terms of pressure, discharge, rotational speed and torque. A performance guarantees for hydro turbines shall be contain, as a minimum, guarantees covering power, discharge and specific hydraulic energy, efficiency, maximum momentary overspeed and maximum momentary pressure and maximum steady-state runaway speed, as well as guarantees related to cavitation. But, present in Korea, the absence of testing laboratories and technical criteria for the performance test of small hydropower degrades the efficiency of the domestic hydropower machines, and makes it difficult to objectively evaluate the performance of hydro turbine. Therefore We planned making a basis of performance test of small hydropower turbine by using our flowmeter calibration system the largest one in Korea. We planned the maximum measurable power of hydro turbine will be 200 kW in our system.
-
The performance of a francis turbine is studied by applying a new performance evaluation tester. the performance of a francis turbine is predicted under several operating conditions and the prediction results are compared with model test data. As a result, it is demonstrated that the present method can predict the performance of a francis turbine with high accuracy and has usefullness as an engineering tool on the performance of hydraulic turbines.
-
소수력자원의 개발을 위해서는 소수력발전입지에 대한 설계변수의 분석이 매우 중요하다. 설계변수는 해당유역의 강우사상과 밀접한 관계가 있으므로 이에 대한 정량적인 분석이 요구된다. 본 연구에서는 수계별 소수력발전입지에 대하여 설계변수의 특성을 분석하였다. 분석결과, 금강수계, 남한강수계 및 섬진강수계는 유역면적이 증가하여도 비가용량의 변화가 크지않지만, 낙동강수계와 북한강수계는 유역면적의 크기에 관계없이 비가용량의 변화가 크게 나타났다. 또한 비출력량의 경우에도 비가용량과 유사하게 금강수계, 남한강수계 및 섬진강수계는 유역면적이 증가하여도 비출력량의 변화가 크지않지만, 낙동강수계와 북한강수계는 유역면적의 크기에 관계없이 비출력량의 변화가 크게 나타났다. 이러한 현상은 우리나라의 연강수량이 남부지방이 중부지방에 비하여 많기 때문으로 판단된다. 낙동강수계는 하도가 남북으로 길기 때문에 소수력발전입지의 위치에 따라 비가용량의 크기의 변화가 크고, 북한강수계도 이와 비슷한 경향을 갖는다. 반면에 금강수계, 남한강수계 및 섬진강수계는 하도가 동서방향으로 길기 때문이다. 또한 연간가동율의 경우에는 모든 수계에 대하여 변화가 크지 않았고, 유역면적의 변화에 대해서도 큰 변화가 없었다.
-
우리나라 전국의 사찰수는 약 22,000개로 추정되며, e-나라지표에 의하면 사찰 역사가 오래되거나 전통 양식의 건축물과 문화재 등을 간직한 사찰로 문화체육관광부가 지정하는 전통사찰은 2010년 3월말 현재 전체의 4.2%인 935개로 알려져 있다. 대도시에 위치한 사찰을 제외하면 일반적으로 사찰은 계곡에 위치하여 인근에 하천이 있으며, 유역이 작아 유량은 적으나 경사가 심해 낙차를 크게 얻을 수 있다. 또한 설계제원이 비슷한 전통사찰들을 그룹핑하고 소수력발전시스템을 Kit형태로 표준화하여 개발한다면 초기투자비를 저감할 수 있는 장점도 있다. 따라서 본 연구에서는 전통사찰에 소수력발전의 적용가능성을 타진하기 위하여 유역면적이
$49.71km^2$ 인 사찰 1지점을 선정하여 인근의 하천을 이용한 소수력발전 성능특성을 분석하였다. 분석결과 단위 유효낙차당 설비용량은 약 9.3kW, 연간전기생산량은 약 28,602kWh로 산정되었으며, 낙차가 커질수록 설비규모와 연간전기생산량은 비례하여 증가될 것으로 추정된다. 부존자원이 부족하여 에너지해외의존도가 97%가 넘는 현실을 감안할때 전통사찰에 대한 타당성 조사를 통해 소수력발전을 적용함으로서 사찰에서 사용되는 전기에너지의 절약과 친환경 재생에너지의 활용을 확대해 나가는 것이 바람직 할 것으로 사료된다. -
기존의 수력발전방식은 물의 위치에너지를 이용하므로 적합한 입지가 제한된다. 그러나 수류에너지를 이용한 발전방식은 기존의 수력발전과는 달리 물의 운동에너지를 이용하기 때문에 입지에 제한이 적으며, 물은 밀도가 크기 때문에 작은 유속으로도 많은 에너지를 생산할 수 있고,댐을 필요로 하지 않으므로 하천생태계 및 환경에 영향을 주지 않는 장점이 있다. 따라서 하천 뿐 아니라 기존 물관련시설의 미활용 방류수를 이용할 수 있으므로 수력잠재량이 매우 크다. 본 연구에서는 다목적댐 방수로의 수류에너지 잠재량 산정을 위하여 유역면적이
$2,285km^2$ 이고 연평균 방류량이 약$29,389m^3/s$ 인 남강댐을 선정하였다. 분석결과 남강 다목적댐의 방수로를 이용한 수류에너지 잠재량은 연간 약 639,685.35kWh로 산정되었다. 향후 하천생태계와 환경에 영향을 주지않는 재생에너지원으로서의 수류에너지 이용은 미활용에너지의 적극 활용 측면과 미래전력 수요에 대한 중요한 원천으로써 재고되어야 할 것이다. -
In this work, the electrochemical properties of the surface treated multi-walled carbon nanotubes (MWNTs) are investigated for supercapacitors. Nitrogen- and oxygen functional groups containing MWNTs are prepared by nitrogen precursors and acidic treatment, respectively. The surface properties of the MWNTs are confirmed by X-ray photoelectron spectroscopy (XPS) and Zeta-potential measurements. The electrochemical properties of the MWNTs are investigated by cyclic voltammetry, impedance spectra, and charge-discharge cycling performance in 1 M
$H_2SO_4$ at room temperature. As a result, these functionalized MWNTs lead to an increase in the specific capacitance as compared with the pristine MWNTs. It proposes that the pyridinic and pyridinic-N-oxides nitrogen species influence on the specific capacitance due to their positive charges, and thus an improved electron transfer at high current loads, since they are the most important functional groups affecting capacitive behaviors. -
In this work, porous carbon based electrodes are prepared by carbonization using poly(vinylidene fluoride) (PVDF)/carbon nanotube (CNT) composites to further increase the specific capacitance for supercapacitors. Electrode materials investigate the aspects of specific capacitance, pore size distribution and surface area: influence of carbonization temperatures of PVDF/CNT composites. The electrochemical properties are investigated by cyclic voltammetry, impedance spectra, and galvanostatic charge-discharge performance with in
$TEABF_4$ (tetraethylammonium tetrafluoroborate)/acetonitrile as non-aqueous electrolyte. From the results, the highest value of specific capacitance of ~101$F{\cdot}g^{-1}$ is obtained for the samples carbonized at$600^{\circ}C$ . Furthermore, pore size of samples control be low 7 nm through carbonization process. It is suggested that micropores significantly contribute to the specific capacitance, resulting from improved charge transfer. -
Jang, Jae Kyung;Choi, Jung Eun;Ryou, Young Sun;Lee, Sung Hyung;Kim, Jong Goo;Kang, Youn Koo;Kim, Young Hwa;Lee, Hyung Mo 219.1
These studies carried out to know the effect of ammonium on the current generation in the microbial fuel cells (MFCs). MFCs used in the study were enriched with anaerobic digestion sludge and operated for 3 years using artificial wastewater (AWW). When the current was stably generated, ammonium ion with$27.0{\pm}0.0$ ,$51.5{\pm}0.0$ ,$103.5{\pm}0.0mg/L$ with acetate fed into the anode compartment. The current values under condition included ammonium were changed from its initial$6.30{\pm}0.06$ to$6.28{\pm}0.36$ ,$5.95{\pm}0.61$ ,$5.64{\pm}0.38mA$ , respectively. The current value was slightly decreased to$5.64{\pm}0.38mA$ compared to$6.30{\pm}0.06mA$ generated from MFC without ammonium ion in the AWW. But After 3days operating under ammonium concentration with$103.5{\pm}0.0mg/L$ , the current was unstably generated when artificial wastewater without ammonium was fed again. MFC enriched with AWW without ammonium ion was inhibited by high concentration of ammonium. At this time, the ammonium was removed 5.27~16.41 mg per day under all conditions. -
The oxyfluorination effects of electrospun carbon nanofibers (OFACFs) were investigated for
$CO_2$ storage. Carbon nanofibers were prepared form poly acrylonitrile / N,N-dimethylformamide solution through electrospinning method and heat treatment. Chemical activation of carbon nanofibers were carried out in order to improve the pore structure. And the surface modification of activated carbon nanofibers was conducted by oxyfluorination to improve the$CO_2$ storage on effect of introduced functional groups. The samples were labeled CF (electrospun carbon nanofiber), ACF (activated carbon nanofibers), OFACF-1 ($F_2:O_2$ = 3:7), OFACF-2 ($F_2:O_2$ = 5:5) and OFACF-3 ($F_2:O_2$ = 7:3). The functional group of OFACFs was investigated by x-ray photoelectron spectroscopy analysis. The specific surface area, pore volume and pore size of OFACFs were calculated and pore shape was estimated by the BET equation. Through the adsorption isotherm, the specific surface area and pore volume significantly decreased by oxyfluorination. -
In recent years, the importance of Carbon Capture and Storage (hereafter CCS) is growing bigger and bigger. The development and commercialization of CCS technology are concerned for reducing carbon dioxide(
$CO_2$ ) emissions. For the most studies, the technology of$CO_2$ storage is known as the geological storage, ocean sequestration, mineral carbonation, industrial utilization, and so on. The geological storage is adjudged the most reasonable technology from economic and environmental aspects. Generally, the$CO_2$ geological storage is comprised of compression - transportation - drilling/injection - storage/management process. The critical problem is a leakage of$CO_2$ in all process. For resolving a leakage problem, it is necessary to predict and build a monitoring system. Those systems are proved safety of a leakage and received positive social perceptions of$CO_2$ geological storage. For those reasons, a risk assessment of$CO_2$ geological storage is required. A risk assessment is an estimated process of the possible effects when spilling$CO_2$ . Although numerous studies of risk assessment have studied, it is incomplete to evaluate a risk and disaster quantitatively. The risk assessment will be developed for domestic application and safe$CO_2$ geological storage considering characteristics of Korea. -
Biodiesel and biodiesel blend fuel are receiving increasing attention as alternative fuels for diesel engines without substantial modifications. Biodiesel fuels and blending have been widely studied and applied in diesel engine because of biodiesel's lower sulfur, lower aromatic hydrocarbon and higher oxygen content. Biodiesels have the potential to be oxidized in different condition. It has reported that oxidation deterioration of biodiesel is different in the condition of storage and oxidation causes chemical property change of methyl esters. Sunlight intensity, temperature, material of container and contact surface with oxygen are key dominant factors accelerating oxidation deterioration. In this study, we chose temperature among key oxidation conditions and metal container filled with biodiesel was heated at about
$110^{\circ}C$ for 10 days in order to accelerate oxidation deterioration. To better understand the effect of biodiesel blends on emission, steady state tests were conducted on a heavy duty diesel engine. The engine was fueled with Ultra Low Sulphur Diesel(ULSD), a blend of 10% and 20%(BD10, BD20) on volumetric basis, equipped with a common rail direct injection system and turbocharger, lives up to the requirements of EURO 3. The experimental results show that the blend fuel of normal biodiesel with BD10 and BD20 increased NOx. The result of PM was similar to diesel fuel on BD10, but the result of PM on BD20 was increased about 63% more than its of diesel. The blend fuel of Oxidation biodiesel with BD10 and BD20 increased NOx as the results of normal biodiesel. But PM was all increased on BD10 and BD20. Especially THC was extremely increased when test fuel contains biodiesel about 140% more than its of diesel. Through this study, we knew that oxidation deterioration of biodiesel affects emission of diesel engine. -
In this study, we prepared the nitrogen-containing carbon spheres with mesopore processed by a facile polymerization-induced colloid aggregation method including carbonization in order to investigate the characterization and the effect on their carbon dioxide adsorption behaviors. The carbonization temperature was varied in the range of
$600^{\circ}C$ to$900^{\circ}C$ . The nitrogen contents of the mesoporous carbon sphere were characterized using XPS. The carbon dioxide adsorption capacities of the prepared mesoporous carbon sphere were determined by the amounts of carbon dioxide adsorptions at 298 K and 1.0 atm. The results showed that the prepared mesoporous carbons were highly effective for the carbon dioxide adsorption due to the increasing the affinity of the basic functionalities of adsorbent surface to acidic carbon dioxide. Maximum adsorption capacities of carbon dioxide at$25^{\circ}C$ were achieved up to 106 mg/g. -
In this study, we prepared the magnesium oxide decorated ordered mesoporous carbons processed by the reduction of magnesium oxide precursor on the CMK-3 surfaces in order to investigate the characterization and the effect on their carbon dioxide adsorption behaviors. The magnesium contents of the prepared samples were characterized using XPS. The textural properties of the prepared samples were investigated by
$N_2$ /77 K adsorption isotherms by BET equation. The carbon dioxide adsorption capacities of the prepared samples were investigated by the amounts of carbon dioxide adsorptions at 298 K and 1.0 atm. The results showed that the magnesium oxide on the CMK-3 surface enhanced interaction between carbon dioxide and adsorbents. Consequently, it was found that the magnesium oxide led to an increase in the carbon dioxide adsorption capacity of the CMK-3.