권호 표지

한국전기전자재료학회논문지 (Journal of the Korean Institute of Electrical and Electronic Material Engineers) (Journal of the Korean Institute of Electrical and Electronic Material Engineers)

한국전기전자재료학회 (The Korean Institute of Electrical and Electronic Material Engineers)

  • 격월간
  • /
  • 1226-7945(pISSN)
  • /
  • 2288-3258(eISSN)

Aim & Scope

The Journal of the Korean Institute of Electrical and Electronic Material Engineers is published 6 times annually by the Korean Institute of Electrical and Electronic Material Engineers (KIEEME). Abbreviated title is ‘J. Korean Inst. Electr. Electron. Mater. Eng.’. It was launched in 1988. It is devoted to reports of original short communications, research and review articles. The J. Korean Inst. Electr. Electron. Mater. Eng. encompasses all types of semiconductor, electronic ceramics, insulation materials, thin films and sensors, display and optical devices, superconductor and magnetic materials, high voltage and discharge engineering, nano and oxide electronics, energy materials, technology education, light source and application technology, and disaster prevention materials, and so on. Full text is freely available from: http://www.jkieeme.org/paper/intro/intro03.htm. It is printed on acid-free paper. Indexed in Korea Citation Index.

http://www.jkieeme.org KSCI KCI

제29권10호

  1. 강창수;이재학 595
    https://doi.org/10.4313/JKEM.2016.29.10.595 PDF KSCI
    In this paper, the oxide currents of thin silicon oxides is investigated. The oxide currents associated with the on time of applied voltage were used to measure the distribution of voltage stress induced traps in thin silicon oxide films. The stress induced leakage currents were due to the charging and discharging of traps generated by stress voltage in the silicon oxides. The stress induced leakage current will affect data retention in memory devices. The oxide current for the thickness dependence of stress current and stress induced leakage currents has been measured in oxides with thicknesses between $109{\AA}$, $190{\AA}$, $387{\AA}$, and $818{\AA}$ which have the gate area $10^{-3}cm^2$. The oxide currents will affect data retention and the stress current, stress induced leakage current is used to estimate to fundamental limitations on oxide thicknesses.
  2. 이민선;윤지선;박운익;홍연우;백종후;조정호;박용호;정영훈 601
    https://doi.org/10.4313/JKEM.2016.29.10.601 PDF KSCI
    Piezoelectric thick films of soft $Pb(Zr,Ti)O_3$ (PZT) based commercial material (S55) were fabricated using a conventional tape casting method. Ag-Pd electrodes were printed on the piezoelectric film at room temperature and all 5 layered films with a dimension of $12mm{\times}16mm$ were successfully laminated for a multi-layered piezoelectric ceramic actuator. The laminated specimens were co-fired at $1,100^{\circ}C$ for 1 h. A flat layered and dense microstructure was obtained for the $112{\mu}m$ thick piezoelectric actuator after sintering process. Thereafter, a prototype piezoelectric speaker was fabricated using the multi-layered piezoelectric ceramic actuator which can operate as a bimorph. Its SPL (sound pressure level) characteristic was also evaluated for speaker application. Frequency response revealed that the output SPL with a root mean square voltage of 10 V increased gradually to the highest peak of 87.5 dB for 1.5 kHz and exhibited a relatively stable behavior over the measured frequency range (${\leq}20kHz$) at a distance of 10 cm, implying that the fabricated piezoelectric speaker is potential for speaker applications.
  3. 김유석;한종대;류주현;정영호 608
    https://doi.org/10.4313/JKEM.2016.29.10.608 PDF KSCI
    In this study, in order to develop relaxor ferroelectric ceramics for refrigeration device application with large electrocaloric effect and low sintering temperature, PLZT(8/65/35) ceramics was fabricated using conventional solid-state method with the variation of sintering temperature ($1,050^{\circ}C$, $1,100^{\circ}C$, $1,200^{\circ}C$). The XRD pattern of all specimens indicated general perovskite structure with secondary phase. From the results of temperature dependence of dielectric constant, the $T_C$ (ferroelectric-paraelectric phase transition temperature) was shifted toward high temperature with increasing sintering temperature. When the specimen was sintered at $1,100^{\circ}C$, the optimal value of ${\Delta}T{\sim}0.349^{\circ}C$ in ambient temperature of $215^{\circ}C$ was appeared. It is considered that PLZT(8/65/35) ceramics possess the possibility of refrigeration device application.
  4. 박재준 613
    https://doi.org/10.4313/JKEM.2016.29.10.613 PDF KSCI
    The aim of this study is to improve of dielectric properties using epoxy/nano alumina composites with adding glycerol diglycidyl ether (GDE:1,2 g). This paper deals with the effects of dielectric properties(${\epsilon}^{\prime}_r$ and $tan{\delta}$) for epoxy/nano alumina contents (1,3 phr) and GDE addition (1,2 g)composites. 5 kinds specimen were prepared with containing epoxy resins, epoxy nano alumina composites. Average particle size of nano used were 30 nm. The nano alumina used were gamma phase particles of spherical shape. The suppression of epoxy chain motion by addition of nano alumina+GDE decreased dielectric loss and relative permittivity magnitude.
  5. 이명복 620
    https://doi.org/10.4313/JKEM.2016.29.10.620 PDF KSCI
    Ferroelectric $Pb(Zr_{0.52}Ti_{0.48})O_3$ (PZT) films were deposited on SrTiO3(100) substrate by using conductive $SrRuO_3$ films as underlayer and their structural and ferroelectric properties were investigated. PZT films were grown in (00l) orientation on well lattice-matched pseudo-cubic $SrRuO_3$ films. Thickness dependence of ferroelectric and electrical properties of PZT films was investigated. PZT film with 400 nm thickness showed a remanent polarization ($P_r$) of $29.0{\mu}C/cm^2$ and coercive field ($E_c$) of 83 kV/cm, and $P_r$ decreased and $E_c$ increased with thickness reduction. The dielectric constant for PZT films showed gradual decrease with thickness reduction. Breakdown field of PZT films did not show the thickness dependence and displayed as high value as 1 MV/cm.
  6. 권오태;김태완 625
    https://doi.org/10.4313/JKEM.2016.29.10.625 PDF KSCI
    Electrical and optical properties of the AC voltage driven organic light-emitting diodes were investigated by measuring the electroluminescence of the device. Device structure of ITO(170 nm)/TPD(40 nm)/Alq3(60 nm)/LiF(0.5 nm)/Al(100 nm) was manufactured using a thermal evaporation. Sinusoidal and square-type AC voltage was applied to the device using a function generator. Amplitude of the applied voltage was 9.0 V, and a frequency was varied from 50 Hz to 50 kHz. Electroluminescence out of the device was measured in a Si photodetector simultaneously with the applied voltage together. An intensity and a delayed residual luminescence from the device were depended on the frequency of the sinusoidal voltage. It is thought to be due to a contribution of the capacitive nature in the equivalent circuit of the device. An electron mobility was estimated using a time constant obtained from the luminescence of the device driven by the square-type AC voltage.
  7. 한태희;임성훈 630
    https://doi.org/10.4313/JKEM.2016.29.10.630 PDF KSCI
    In this paper, we analyzed the power consumption and the accumulated energy in HTSC (high-TC superconducting elements) according to the resistance of HTSC element and the winding current of transformer type SFCL (superconducting fault current limiter) using double quench. For the analysis, two different inductances of the one secondary winding among two secondary windings comprising the transformer type SFCL were selected and the short-circuit tests were carried out. The consumed power and the accumulated energy in HTSC element connected into the secondary winding with larger inductance were analyzed to be larger compared to the one connected into the secondary winding with lower inductance.
  8. 박경수;왕국명;황성철;김선재;길경석 635
    https://doi.org/10.4313/JKEM.2016.29.10.635 PDF KSCI
    This paper dealt with the deterioration characteristics and an on-line diagnosis equipment for SPDs (surge protective devices). An accelerated aging test was carried out using a $8/20{\mu}s$ standard lightning impulse current to analyze the changes of electrical characteristics and to propose the diagnostic parameters and the criterion for deterioration of ZnO varistor which is the core component of SPDs. Based on the experimental results, an on-line diagnosis equipment for SPD was fabricated, which can measure the total leakage current, reference and clamping voltage. The leakage current measurement circuit was designed using a low-noise amplifier and a clamp type ZCT. A linear controller, the leakage current measurement part and a HVDC were used in the measurement of reference voltage. The measurement circuit of clamping voltage consisted of a surge generator and a coupling circuit. In a calibration process, measurement error of the prototype equipment was less than 3%.
  9. 박재준 641
    https://doi.org/10.4313/JKEM.2016.29.10.641 PDF KSCI
    Coil specimen was prepared by coating a copper wire with two varnish thin layers: the first was polyamideimide (PAI)/nanosilica (5 wt%) varnish and the second was anti-corona PAI/nanosilica (15 wt%) varnish. Insulation breakdown voltage was investigated under inverter surge condition at $20^{\circ}C$, $70^{\circ}C$, $100^{\circ}C$, $150^{\circ}C$, $200^{\circ}C$, $250^{\circ}C$, respectively. The insulation lifetime of the two layered coil was tens of times longer than that of original PAI coil. And the insulation lifetime decreased with increasing ambient temperature because there was weak binding strength between copper and varnish layer.
  10. 진인영;최순호;김관식;허창수 647
    https://doi.org/10.4313/JKEM.2016.29.10.647 PDF KSCI
    The power relay can easily control high voltage and high current through metallic contacts. In addition, it has the advantage in reasonable price. So it has been used in many applications. But the power relay has a weak point by mechanical movements. These mechanical movements cause the bouncing phenomenon. Arc and bouncing phenomenon are the main causes of electric abrasion and material erosion. In this study, mechanical repetitive experiments and repetitive experiments in electrically connected state are conducted. Then these two experimental results in terms of bouncing phenomenon and changes in the contact surface are compared. In all number of repetitions, contacts in an electrically connected state cause smaller number of bounce. Also, It has lower contents of silver on eroded surface than the other. The experimental results would be helpful to the further study of contacts life span.
  11. 임채남;이정민;박병준;강승호;정해원 652
    https://doi.org/10.4313/JKEM.2016.29.10.652 PDF KSCI
    Thermal batteries use inorganic salt as electrolyte, which is inactive at room temperature. As soon as heat pellets are fired by an igniter, all the solid electrolytes are instantly melted into excellent ionic conductors. However, the abnormal heat generation by the igniter flame or heat pellets causes the thermal decomposition of the electrode and the melting of the anode, eventually leading to a thermal runaway, which results in overheating or explosion. The thermal runaway can be significantly reduced by the adoption of $Zr/BaCrO_4$ heat papers. In this study, the heat papers with various ratios of fuel (Zr) and oxidizer ($BaCrO_4$) were prepared by the paper-making process. We have investigated the calorimetric value, burning rate, and ignition sensitivity. The ignition test of heat pellets and the discharge test of thermal batteries were also carried out. At the composition of 40 wt.% of Zr, the heat papers showed the highest specific calorimetric value and burning rate. As a result, $Zr/BaCrO_4$ heat paper made by the paper-making process has shown the applicability for thermal batteries.
  12. 송승원;민의홍;이동원;김정수;남대근;오원태 659
    https://doi.org/10.4313/JKEM.2016.29.10.659 PDF KSCI
    Thermal and electrical conductivities of the natural, artificial, and expandable graphites were analyzed after treatment in NaOH aqueous solution. In order to investigate the elimination of the oxidized groups and impurities on the graphite surfaces after NaOH treatment, the graphite samples were structurally characterized by using XRD, XPS, Raman, FE-SEM. The thermal and electrical conductivities of the graphite samples were significantly improved after NaOH treatment. These results were caused by the structural rehabiliation.
  13. 이한찬 665
    https://doi.org/10.4313/JKEM.2016.29.10.665 PDF KSCI
    Prevailing dissemination of machine tools and cutting technology have caused drastic developments of high speed dry machining with work materials of high hardness, and demands on the high-hardness-materials with high efficiency have become increasingly important in terms of productivity, cost reduction, as well as environment-friendly issue. Addition of Si to TiAlN has been known to form nano-composite coating with higher hardness of over 30 GPa and oxidation temperature over $1,000^{\circ}C$. However, it is not easy to add Si to TiAlN by using conventional PVD technologies. Therefore, Ti-Al-Si-N have been prepared by hybrid process of PVD with multiple target sources or PVD combined with PECVD of Si source gas. In this study, a single composite target of Ti-Al-Si was prepared by powder metallurgy of MA (mechanical alloying) and SPS (spark plasma sintering). Properties of he resulting alloying targets were examined. They revealed a microstructure with micro-sized grain of about $1{\sim}5{\mu}m$, and all the elements were distributed homogeneously in the alloying target. Hardness of the Ti-Al-Si-N target was about 1,127 Hv. Thin films of Ti-Al-Si-N were prepared by unbalanced magnetron sputtering method by using the home-made Ti-Al-Si alloying target. Composition of the resulting thin film of Ti-Al-Si-N was almost the same with that of the target. The thin film of Ti-Al-Si-N showed a hardness of 35 GPa and friction coefficient of 0.66.