Steel and Composite Structures

  • 제50권5호
  • /
  • Pages.515-529
  • /
  • 2024
  • /
  • 1229-9367(pISSN)
  • /
  • 1598-6233(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Assessment of cold-formed steel screwed beam-column conections: Experimental tests and numerical simulations

  • Merve Sagiroglu Maali (Civil Engineering Department, Erzurum Technical University) ;
  • Mahyar Maali (Civil Engineering Department, Erzurum Technical University) ;
  • Zhiyuan Fang (School of Engineering, The University of Waikato) ;
  • Krishanu Roy (School of Engineering, The University of Waikato)
  • 투고 : 2023.04.03
  • 심사 : 2023.11.08
  • 발행 : 2024.03.10
⟨ 이전 논문 다음 논문 ⟩

초록

Cold-formed steel (CFS) is a popular choice for construction due to its low cost, durability, sustainability, resistance to high environmental and seismic pressures, and ease of installation. The beam-column connections in residential and medium-rise structures are formed using self-drilling screws that connect two CFS channel sections and a gusset plate. In order to increase the moment capacity of these CFS screwed beam-column connections, stiffeners are often placed on the web area of each single channel. However, there is limited literature on studying the effects of stiffeners on the moment capacity of CFS screwed beam-column connections. Hence, this paper proposes a new test approach for determining the moment capacity of CFS screwed beam-column couplings. This study describes an experimental test programme consisting of eight novel experimental tests. The effect of stiffeners, beam thickness, and gusset plate thickness on the structural behaviour of CFS screwed beam-column connections is investigated. Besides, nonlinear elasto-plastic finite element (FE) models were developed and validated against experimental test data. It found that there was reasonable agreement in terms of moment capacity and failure mode prediction. From the experimental and numerical investigation, it found that the increase in gusset plate or beam thickness and the use of stiffeners have no significant effect on the structural behaviour, moment capacity, or rotational capacity of joints exhibiting the same collapse behaviour; however, the capacity or energy absorption capacities have increased in joints whose failure behaviour varies with increasing thickness or using stiffeners. Besides, the thickness change has little impact on the initial stiffness.

키워드

참고문헌

  1. ABAQUS (2018), Analysis User's Manual-Version 6.14-2, ABAQUS Inc., USA.
  2. Alireza, B.S., Petkovski, M., Pilakoutas, K. and Mirghaderi, R. (2012), "Development of cold-formed steel elements for earthquake resistant moment frame buildings", Thin-Wall. Struct., 53. https://doi.org/10.1016/j.tws.2012.01.004
  3. American Iron and Steel Institute (2016), Specification for the Design of Cold-Formed S.S.M, USA.
  4. Ananthi, G.B.G., Roy, K., Chen, B. and Lim, J.B.P. (2019), "Testing, simulation and design of back-to-back built-up cold-formed steel unequal angle sections under axial compression", Steel Compos. Struct., 33(4). https://doi.org/10.12989/scs.2019.33.4.595.
  5. Anwar, G.A., Dinu, F. and Ahmed, M. (2019), "Numerical study on ultimate deformation and resistance capacity of bolted T-stub connection", Int. J. Steel Struct., 19(3). https://doi.org/10.1007/s13296-018-0186-8.
  6. Anwer, B., Saad, S. and Osman, H. (2012), "Structural performance of bolted moment connections among single cold-formed channel sections", Int. J. Eng. Technol., 2(4).
  7. Australian/New Zealand Standard (AS/NZS) (2018), Cold-Formed Steel Structures, AS/NZS 4600:2018, Australia, New Zealand.
  8. Aydin, A.C., Ardalani, A., Maali, M. and Kilic, M. (2021), "Numeric modelling of innovative semi-rigid connections under cyclic loading", Steel Construct., 14(1). https://doi.org/10.1002/stco.201900037.
  9. Aydin, A.C., Kilic, M., Maali, M. and Saʇiroʇlu, M. (2015), "Experimental assessment of the semi-rigid connections behavior with angles and stiffeners", J. Construct. Steel Res., 114. https://doi.org/10.1016/j.jcsr.2015.08.017.
  10. BS EN 1993-1-8 (2005), Design of Steel Structures; Design of Joints, European Committee for Standardization, Brussels, Belgium.
  11. Chavan, A.M. and Angalekar, S.S. (2016), "Finite element analysis of cold form perforated steel beam column connection IRJET Journal Finite element analysis of cold form perforated steel beam column connection", Int. Res. J. Eng. Technol., 3(7).
  12. Chen, B., Roy, K., Fang, Z., Uzzaman, A., Pham, C.H., Raftery, G.M. and Lim, J.B.P. (2022), "Shear capacity of cold-formed steel channels with edge-stiffened web holes, unstiffened web holes, and plain webs", J. Struct. Eng., 148(2). https://doi.org/10.1061/(asce)st.1943-541x.0003250.
  13. Chen, B., Roy, K., Uzzaman, A., Raftery, G. and Lim, J.B.P. (2020), "Axial strength of back-to-back cold-formed steel channels with edge-stiffened holes, un-stiffened holes and plain webs", J. Construct. Steel Res., 174. https://doi.org/10.1016/j.jcsr.2020.106313.
  14. Daudet, L.R. and LaBoube, R.A. (1996), "Shear behavior of self drilllng screws used in low ductility steel", In International Specialty Conference on Cold-Formed Steel Structures: Recent Research and Developments in Cold-Formed Steel Design and Construction.
  15. Fang, Z., Roy, K., Xu, J., Dai, Y., Paul, B. and Lim, J.B.P. (2022), "A novel machine learning method to investigate the web crippling behaviour of perforated roll-formed aluminium alloy unlipped channels under interior-two flange loading", J. Build. Eng., 51. https://doi.org/10.1016/j.jobe.2022.104261.
  16. Hancock, G.J. (2016), "Cold-formed steel structures: Research review 2013-2014:", 19(3), 393-408. https://doi.org/10.1177/1369433216630145.
  17. Hassan, E.M., Serror, M.H. and Mourad, S.A. (2017), "Numerical prediction of available rotation capacity of cold-formed steel beams", J. Construct. Steel Res., 128. https://doi.org/10.1016/j.jcsr.2016.08.010.
  18. Hazlan, A.H., Tahir, M.M., Sulaiman, A. and Mahendran, M. (2011), "Bolted beam-column moment connections between cold-formed steel members", In Incorporating Sustainable Practice in Mechanics of Structures and Materials - Proceedings of the 21st Australian Conference on the Mechanics of Structures and Materials. https://doi.org/10.1201/b10571-119.
  19. Kilic, M., Maali, M. and Aydin, A.C. (2019), "The preliminary uniaxial compression behavior of corrugated cold formed steel members", Architect. Civil Eng. Environ., 12(2). https://doi.org/10.21307/acee-2019-027.
  20. Lee, Y.H., Tan, C.S., Mohammad, S., Md Tahir, M. and Shek, P.N. (2014) "Review on cold-formed steel connections", Sci. World J., https://doi.org/10.1155/2014/951216.
  21. Maali, M. (2020), "Failure modes of end-plate connections with outer flange stiffeners: an experimental and numerical study", Sadhana - Academy Proceedings Eng. Sci., 45(1). https://doi.org/10.1007/s12046-019-1262-2.
  22. Maali, M., Kilic, M. and Aydin, A.C. (2016), "Experimental model of the behaviour of bolted angles connections with stiffeners", Int. J. Steel Struct., 16(3). https://doi.org/10.1007/s13296-015-0183-0.
  23. Maali, M., Kilic, M. and Aydin, A.C. (2019), "Experimental behaviour of bolted connections with stiffeners", Steel Construct., 12(2). https://doi.org/10.1002/stco.201800010.
  24. Maali, M., Kilic, M., Sagiroglu, M. and Aydin, A.C. (2017), "Experimental model for predicting the semi-rigid connections' behaviour with angles and stiffeners", Adv. Struct. Eng., 20(6). https://doi.org/10.1177/1369433216665621.
  25. Maali, M., Kilic, M., Sagiroglu, M. and Cuneyt Aydin, A. (2018), "Experimental behavior of bolted T-stub connections with IPE standard profile", J. Civil Environ. Eng., 08(03). https://doi.org/10.4172/2165-784x.1000312.
  26. Maali, M., Sagiroglu, M. and Semih Solak, M. (2018), "Experimental behavior of screwed beam-to-column connections in cold-formed steel frames", Arab. J. Geosci., 11(9). https://doi.org/10.1007/s12517-018-3540-4.
  27. Mills, J. and LaBoube, R. (2002), "Self-drilling screw joints for cold-formed channel portal frames", In International Specialty Conference on Cold-Formed Steel Structures: Recent Research and Developments in Cold-Formed Steel Design and Construction. https://doi.org/10.1061/(asce)0733-9445(2004)130:11(1799).
  28. Mills, J. and LaBoube, R. (2004), "Self-drilling screw joints for cold-formed channel portal frames", J. Struct. Eng., 130(11), 1799-1806. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:11(1799).
  29. Rogers, C.A. and Hancock, G.J. (1998), "Behaviour of thin G550 sheet steel screwed connections", In International Specialty Conference on Cold-Formed Steel Structures: Recent Research and Developments in Cold-Formed Steel Design and Construction.
  30. Roy, K., Ting, T.C.H., Lau, H.H. and Lim, J.B.P. (2018), "Nonlinear behaviour of back-to-back gapped built-up cold-formed steel channel sections under compression", J. Construct. Steel Res., 147. https://doi.org/10.1016/j.jcsr.2018.04.007.
  31. Sagiroglu, M. (2018), "Experimental evaluation of the post-fire behavior of steel T-component in the beam-to-column connection", Fire Safety J., 96. https://doi.org/10.1016/j.firesaf.2018.01.007.
  32. Sagiroglu, M., Maali, M. and Yazici, C. (2023), "Experimental investigation of screwed beam-column connection using cold-formed steel back-to-back sections with gusset-plate", Structures, 47, 2025-2036. https://doi.org/https://doi.org/10.1016/j.istruc.2022.12.030.
  33. Sagiroglu, M., Maali, M., Kilic, M. and Aydin, A.C. (2018), "A Novel Approach for Bolted T-Stub Connections", Int. J. Steel Struct., 18(3). https://doi.org/10.1007/s13296-018-0034-x.
  34. SB EN ISO 898-1:2009 (2009), Mechanical Properties of Fasteners Made of Carbon Steel and Alloy Steel. Bolts, Screws and Stud, British Standard; UK.
  35. Serror, M.H., Hassan, E.M. and Mourad, S.A. (2016), "Experimental study on the rotation capacity of cold-formed steel beams", J. Construct. Steel Res., 121. https://doi.org/10.1016/j.jcsr.2016.02.005.
  36. Torabian, S., Zheng, B. and Schafer, B.W. (2015), "Experimental response of cold-formed steel lipped channel beam-columns", Thin-Wall. Struct., 89. https://doi.org/10.1016/j.tws.2014.12.003.
  37. UNE-EN 10002-1 (2002), Materiales met'alicos. Ensayos de tracci'on. Parte 1: M'etodo de ensayo a temperatura ambiente, Normalizacion Espanola; Spain.
  38. Wong, M.F. and Chung, K.F. (2002), "Structural behaviour of bolted moment connections in cold-formed steel beam-column sub-frames", J. Construct. Steel Res., 58(2). https://doi.org/10.1016/S0143-974X(01)00044-X.
  39. Yang, H., Wang, H., Qian, H., Jin, X., Chen, D., He, Y., Quanqi Li, Q. and Fan, F. (2022), "Mechanical performance of pre-engineered closed section beam-column connections in CFS frames: Experimental investigation", Structures, 39. https://doi.org/10.1016/j.istruc.2022.03.032.
  40. Zhang, J.H. and Young, B. (2015), "Numerical investigation and design of cold-formed steel built-up open section columns with longitudinal stiffeners", Thin-Wall. Struct., 89. https://doi.org/10.1016/j.tws.2014.12.011.
  41. Zhang, J.H. and Young, B. (2018a), "Experimental investigation of cold-formed steel built-up closed section columns with web stiffeners", J. Construct. Steel Res., 147. https://doi.org/10.1016/j.jcsr.2018.04.008.
  42. Zhang, J.H. and Young, B. (2018b), "Finite element analysis and design of cold-formed steel built-up closed section columns with web stiffeners", Thin-Wall. Struct., 131. https://doi.org/10.1016/j.tws.2018.06.008