Structural Engineering and Mechanics

  • 제90권1호
  • /
  • Pages.51-70
  • /
  • 2024
  • /
  • 1225-4568(pISSN)
  • /
  • 1598-6217(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Influence of high axial compression ratios in RC columns on the seismic response of MRF buildings

  • Sergio Villar-Salinas (Civil and Environmental Engineering Department, Universidad Tecnologica de Bolivar, Campus Tecnologico km 1 Via Turbaco) ;
  • Sebastian Pacheco (Engineering/Research Department, PCEM SAS) ;
  • Julian Carrillo (Department of Civil Engineering, Universidad Militar Nueva Granada) ;
  • Francisco Lopez-Almansa (Department of Architecture Technology, Universitat Politecnica de Catalunya-BarcelonaTech (UPC))
  • 투고 : 2023.03.21
  • 심사 : 2024.04.03
  • 발행 : 2024.04.10
⟨ 이전 논문 다음 논문 ⟩

초록

Poorly designed reinforced concrete (RC) columns of actual moment-resisting frame (MRF) buildings can undergo Axial Compression Ratios (ACR) so high as their demand exceeds their capacity, even for serviceability gravity load combinations, this lack commonly leads to insufficient seismic strength. Nonetheless, many seismic design codes do not specify limits for ACR. The main contribution of this research is to investigate the need to limit the ACR in seismic design. For this purpose, three prototype 6 and 11-story RC MRF buildings are analyzed in this paper, these buildings have columns undergoing excessive ACR, according to the limits prescribed by standards. To better that situation, three types of alterations are performed: retrofitting the abovementioned overloaded columns by steel jacketing, increasing the concrete strength, and reducing the number of stories. Several finite element analyses are conducted using the well-known software SAP2000 and the results are used for further calculations. Code-type and pushover analyses are performed on the original and retrofitted buildings, the suitability of the other modified buildings is checked by code-type analyses only. The obtained results suggest that ACR is a rather reliable indicator of the final building strength, hence, apparently, limiting the ACR in the standards (for early stages of design) might avoid unnecessary verifications.

키워드

과제정보

The first author greatly appreciates the financial support from Fundacion Carolina and Universidad Tecnologica de Bolivar during his Doctoral research. Besides, the help of PCEM SAS with the drafting of some figures is thankfully acknowledged. The authors acknowledge each filiation institution, for facilitating or financing research activities.

참고문헌

  1. Abou-Elfath, H., Ramadan, M. and Alkanai, F.O. (2017), "Upgrading the seismic capacity of existing RC buildings using buckling restrained braces", Alex. Eng. J., 56(2), 251-262. https://doi.org/10.1016/j.aej.2016.11.018.
  2. ACI 318 (2014), Building Code Requirements for Structural Concrete and Commentary.
  3. AIS (2010), NSR-10, Reglamento Colombiano de Construccion Sismo Resistente, Bogota DC.
  4. AISC 360 (2016), Specification for Structural Steel Buildings.
  5. Alfarah, B., Lopez-Almansa, F. and Oller, S. (2020), "Numerical study on the relevance of columns hidden failure modes in the seismic capacity of non-ductile RC Frames", J. Earthq. Eng., 24(9), 1417-1434. https://doi.org/10.1080/13632469.2018.1458666.
  6. Al-Osta, M.A., Khan, U., Baluch, M.H. and Rahman, M.K. (2018), "Effects of variation of axial load on seismic performance of shear deficient RC exterior BCJs", Int. J. Concrete Struct. Mater., 12, 1-20. https://doi.org/10.1186/s40069-018-0277-0.
  7. ASCE 7-16 (2017), Minimum Design Loads for Buildings and other Structures, American Society of Civil Engineers, Reston, Virginia.
  8. ASCE/SEI 41-17 (2017), Seismic Evaluation and Retrofit of Existing Buildings, Standards.
  9. Bhatt, C. and Bento, R. (2014), "The extended adaptive capacity spectrum method for the seismic assessment of plan-asymmetric buildings", Earthq. Spectra, 30(2), 683-703. https://doi.org/10.1193/022112EQS048M.
  10. Buildings Department (HKBD) (2013), Code of Practice for Structural Use of Concrete 2013, The HKSAR Government, Hong Kong.
  11. Caredda, G., Makoond, N., Buitrago, M., Sagaseta, J., Chryssanthopoulos, M. and Adam, J.M. (2023), "Learning from the progressive collapse of buildings", Dev Built Environ 2023, 15, 100194. https://doi.org/10.1016/j.dibe.2023.100194.
  12. Carrillo, J. and Gonzalez, G. (2007), "Inelastic modeling of concrete frames with nonreinforced masonry", DYNA, 74(152), 229-239.
  13. Chen, Z.Y., Chen, W., Zhang, W. and Lou, M.L. (2016), "Effects of axial compression ratio of central columns on seismic performance of a multi-story underground structure", Int. J. Comput. Meth., 13(04), 1641014. https://doi.org/10.1142/S0219876216410140.
  14. China Architecture & Building Press (2010), National Standard of the People's Republic of China, Code for Seismic Design of Buildings (GB 50011-2010), Beijing.
  15. Cimellaro, G.P., Giovine, T. and Lopez-Garcia, D. (2014), "Bidirectional pushover analysis of irregular structures", J. Struct. Eng., 140(9), 04014059. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001032.
  16. Comert, M., Demir, C., Ates, A.O., Orakcal, K. and Ilki, A. (2017), "Seismic performance of three-storey full-scale sub-standard reinforced concrete buildings", Bull. Earthq. Eng., 15, 3293-3320. https://doi.org/10.1007/s10518-016-0023-4.
  17. Computer and Structures Inc. (2016), Concrete Frame Design Manual ACI 318-11 for SAP 2000, Computers & Structures, Inc.
  18. Computer and Structures Inc. (2017), Steel Frame Design Manual AISC 360-16 for SAP 2000.
  19. Dominguez, D., Lopez-Almansa, F. and Benavent-Climent, A. (2016), "Would RC wide-beam buildings in Spain have survived Lorca earthquake (11-05-2011)?", Eng. Struct., 108, 134-154. https://doi.org/10.1016/j.engstruct.2015.11.020.
  20. Elwood, K.J. and Moehle, J.P. (2005), "Drift capacity of reinforced concrete columns with light transverse reinforcement", Earthq. Spectra, 21(1), 71-89. https://doi.org/10.1193/1.1849774.
  21. Elwood, K.J. and Moehle, J.P. (2008), "Dynamic collapse analysis for a reinforced concrete frame sustaining shear and axial failures", Earthq. Eng. Struct. Dyn., 37(7), 991-1012. https://doi.org/10.1002/eqe.787.
  22. EN-1998 (2004), Eurocode 8: Design of Structures for Earthquake Rsistance-Part 1: General Rules, Seismic Actions and Rules for Buildings (EN-1998-1), European Comitee for Standarization.
  23. Fadaei, E., Shakib, H. and Azarbakht, A. (2020), "Structural global performance assessment versus individual element-oriented performance-based assessment", Iran. J. Sci. Technol., Trans. Civil Eng., 44, 141-150. https://doi.org/10.1007/s40996-020-00379-9.
  24. Falcone, R., Carrabs, F., Cerulli, R., Lima, C. and Martinelli, E. (2019, December), "Seismic retrofitting of existing RC buildings: A rational selection procedure based on Genetic Algorithms", Struct., 22, 310-326. https://doi.org/10.1016/j.istruc.2019.08.006.
  25. FEMA 440 (ATC-55) (2005), Improvement of Nonlinear Static Seismic Analysis Procedures, FEMA.
  26. Han, S.W. and Chopra, A.K. (2006), "Approximate incremental dynamic analysis using the modal pushover analysis procedure", Earthq. Eng. Struct. Dyn., 35(15), 1853-1873. https://doi.org/10.1002/eqe.605.
  27. Jaradat, Y. and Far. H. (2021), "Optimum stiffness values for impact element models to determine pounding forces between adjacent buildings", Struct. Eng. Mech., 77(2), 293-304. https://doi.org/10.12989/sem.2021.77.2.293.
  28. Kamal, M., Inel, M. and Cayci, B.T. (2022), "Seismic behavior of mid-rise reinforced concrete adjacent buildings considering soil-structure interaction", J. Build. Eng., 51, 104296. https://doi.org/10.1016/j.jobe.2022.104296.
  29. Leti, M. and Bilgin, H. (2024), "Investigation of seismic performance of a premodern RC building typology after November 26, 2019 earthquake", Struct. Eng. Mech., 89(5), 491-505. https://doi.org/10.12989/sem.2024.89.5.491.
  30. Li, Y.J. and Liu, P. (2012), "Effect of axial compression ratio on ductility and bearing capacity of specially shaped columns with HRB500 reinforcement", Appl. Mech. Mater., 204, 1066-1069. https://doi.org/10.4028/www.scientific.net/AMM.204-208.1066.
  31. Lopez-Almansa, F., Dominguez, D. and Benavent-Climent, A. (2013), "Vulnerability analysis of RC buildings with wide beams located in moderate seismicity regions", Eng. Struct., 46, 687-702. https://doi.org/10.1016/j.engstruct.2012.08.033.
  32. Mander, J.B., Priestley, M.J. and Park, R. (1988), "Theoretical stress-strain model for confined concrete", J. Struct. Eng., 114(8), 1804-1826. https://doi.org/10.1061/(ASCE)0733-9445(1988)114:8(1804).
  33. Miano, A., Chiumiento, G., Formisano, A. and Prota, A. (2022), "How does the knowledge level affect the seismic retrofit cost? The case study of a RC building", Struct. Eng. Mech., 82(5), 557-569. https://doi.org/10.12989/sem.2022.82.5.557.
  34. Moehle, J.P. (2000), "State of research on seismic retrofit of concrete building structures in the US", US-Japan Symposium and Workshop on Seismic Retrofit of Concrete Structures, 16, June.
  35. Nahar, M., Islam, K. and Billah, A.M. (2020), "Seismic collapse safety assessment of concrete beam-column joints reinforced with different types of shape memory alloy rebars", J. Build. Eng., 29, 101106. https://doi.org/10.1016/j.jobe.2019.101106.
  36. Pampanin, S. and Akguzel, U. (2011), "Performance-based seismic retrofit of existing reinforced concrete frame buildings using fibre-reinforced polymers: Challenges and solutions", Struct. Eng. Int., 21(3), 260-270. https://doi.org/10.2749/101686611X13049248220041.
  37. Pujades, L.G., Barbat, A.H., Gonzalez-Drigo, R., Avila, J. and Lagomarsino, S. (2012), "Seismic performance of a block of buildings representative of the typical construction in the Eixample district in Barcelona (Spain)", Bull. Earthq. Eng., 10, 331-349. https://doi.org/10.1007/s10518-010-9207-5.
  38. Quintana Gallo, P., Akguzel, U., Carr, A.J. and Pampanin, S. (2022), "Seismic response of a non-ductile RC frame building subjected to shake-table excitations", Bull. Earthq. Eng., 1-29. https://doi.org/10.1007/s10518-021-01228-4.
  39. Requena-Garcia-Cruz, M.V., Morales-Esteban, A. and Durand-Neyra, P. (2022), "Assessment of specific structural and ground-improvement seismic retrofitting techniques for a case study RC building by means of a multi-criteria evaluation", Struct., 38, 265-278. https://doi.org/10.1016/j.istruc.2022.02.015.
  40. Reyes, J.C. and Chopra, A.K. (2011), "Three-dimensional modal pushover analysis of buildings subjected to two components of ground motion, including its evaluation for tall buildings", Earthq. Eng. Struct. Dyn., 40(7), 789-806. https://doi.org/10.1002/eqe.1060.
  41. Ricci, P., De Luca, F. and Verderame, G.M. (2011), "6th April 2009 L'Aquila earthquake, Italy: Reinforced concrete building performance", Bull. Earthq. Eng., 9, 285-305. https://doi.org/10.1007/s10518-010-9204-8.
  42. Sezen, H. (2008), "Shear deformation model for reinforced concrete columns", Struct. Eng. Mech., 28(1), 39-52. https://doi.org/10.12989/sem.2008.28.1.039.
  43. Sheth, R., Prajapati, J. and Soni, D. (2018), "Comparative study nonlinear static pushover analysis and displacement based adaptive pushover analysis method", Int. J. Struct. Eng., 9(1), 81-90. https://doi.org/10.1504/IJSTRUCTE.2018.090753.
  44. Singh Rawat, V. (2017), "Increasing the strength of existing building using steel jacketing in seismic zone", Int. J. Civil Eng., Diciembre.
  45. Standards New Zealand (SNZ) (1995), Concrete Structure Standard-the Design of Concrete Structures (NZS 3101: Part 1: 1995), Wellington, New Zealand.
  46. Sullivan, T.J., Saborio-Romano, D., O'Reilly, G.J., Welch, D.P. and Landi, L. (2021), "Simplified pushover analysis of moment resisting frame structures", J. Earthq. Eng., 25(4), 621-648. https://doi.org/10.1080/13632469.2018.1528911.
  47. Standards New Zealand (SNZ) (2006), Concrete Structure Standard-the Design of Concrete Structures Incorporating Amendment No. 1 & 2 (NZS 3101: Part 1: 2006-A1&A2), Wellington, New Zealand.
  48. Su, R.K.L. and Wong, S.M. (2007), "Seismic behaviour of slender reinforced concrete shear walls under high axial load ratio", Eng. Struct., 29(8), 1957-1965. https://doi.org/10.1016/j.engstruct.2006.10.020.
  49. Tena-Colunga, A., Godinez-Dominguez, E.A. and Hernandez-Ramirez, H. (2022), "Seismic retrofit and strengthening of buildings. Observations from the 2017 Puebla-Morelos earthquake in Mexico City", J. Build. Eng., 47, 103916. https://doi.org/10.1016/j.jobe.2021.103916.
  50. Tore, E., Demir, C., Comert, M. and Ilki, A. (2021), "Seismic collapse performance of a full-scale concrete building with lightly reinforced columns", J. Struct. Eng., 147(12), 04021207. https://doi.org/10.1061/(ASCE)ST.1943-541X.0003178.
  51. Tsompanakis, Y. (2014), "Earthquake return period and its incorporation into seismic actions", Encyclopedia of Earthquake Engineering, 1-35.
  52. Villar-Salinas, S., Guzman, A. and Carrillo, J. (2021), "Performance evaluation of structures with reinforced concrete columns retrofitted with steel jacketing", J. Build. Eng., 33, 101510. https://doi.org/10.1016/j.jobe.2020.101510.
  53. Yang, Y., Hao, N., Xue, Y., Feng, S., Yu, Y. and Zhang, S. (2022), "Seismic performance of RC columns retrofitted using high-strength steel strips under high axial compression ratios", Struct. Eng. Mech., 84(3), 345-360. https://doi.org/10.12989/sem.2022.84.3.345.
  54. Yu, Q.S. "Kent," Pugliesi, R., Allen, M. and Bischoff, C. (2004), "Assessment of modal pushover analysis procedure and its application to seismic evaluation of existing buildings", 13th World Conf. Earthq. Eng., Paper No. 1104, Vancouver, Canada.
  55. Yuen, T.Y., Kuang, J.S. and Ho, D.Y. (2016), "Ductility design of RC columns. Part 1: Consideration of axial compression ratio", HKIE Trans., 23(4), 230-244. https://doi.org/10.1080/1023697X.2016.1232179.
  56. Zimos, D.K., Papanikolaou, V.K., Kappos, A.J. and Mergos, P.E. (2020), "Shear-critical reinforced concrete columns under increasing axial load", ACI Struct. J., 117(5), 29-39. https://doi.org/10.14359/51725886.