DOI QR코드

DOI QR Code

Two-stage damage identification for bridge bearings based on sailfish optimization and element relative modal strain energy

  • Minshui Huang (School of Civil Engineering and Architecture, Wuhan Institute of Technology) ;
  • Zhongzheng Ling (Tongji Architectural Design (Group) Co., Ltd.) ;
  • Chang Sun (School of Civil Engineering and Architecture, Wuhan Institute of Technology) ;
  • Yongzhi Lei (Centre for Infrastructural Monitoring and Protection, School of Civil and Mechanical Engineering, Curtin University) ;
  • Chunyan Xiang (School of Civil Engineering and Architecture, Wuhan Institute of Technology) ;
  • Zihao Wan (School of Civil Engineering and Architecture, Wuhan Institute of Technology) ;
  • Jianfeng Gu (School of Civil Engineering and Architecture, Wuhan Institute of Technology)
  • 투고 : 2023.01.13
  • 심사 : 2023.05.05
  • 발행 : 2023.06.25

초록

Broad studies have addressed the issue of structural element damage identification, however, rubber bearing, as a key component of load transmission between the superstructure and substructure, is essential to the operational safety of a bridge, which should be paid more attention to its health condition. However, regarding the limitations of the traditional bearing damage detection methods as well as few studies have been conducted on this topic, in this paper, inspired by the model updating-based structural damage identification, a two-stage bearing damage identification method has been proposed. In the first stage, we deduce a novel bearing damage localization indicator, called element relative MSE, to accurately determine the bearing damage location. In the second one, the prior knowledge of bearing damage localization is combined with sailfish optimization (SFO) to perform the bearing damage estimation. In order to validate the feasibility, a numerical example of a 5-span continuous beam is introduced, also the noise robustness has been investigated. Meanwhile, the effectiveness and engineering applicability are further verified based on an experimental simply supported beam and actual engineering of the I-40 Bridge. The obtained results are good, which indicate that the proposed method is not only suitable for simple structures but also can accurately locate the bearing damage site and identify its severity for complex structure. To summarize, the proposed method provides a good guideline for the issue of bridge bearing detection, which could be used to reduce the difficulty of the traditional bearing failure detection approach, further saving labor costs and economic expenses.

키워드

과제정보

This study was supported by the National Natural Science Foundation of China (Project No. 52178300) and the Graduate Innovative Fund of Wuhan Institute of Technology (No: CX2020107).

참고문헌

  1. Ahmadi, H.R. and Anvari, D. (2018), "Health monitoring of pedestrian truss bridges using cone-shaped kernel distribution", Smart Struct. Syst., 22(6), 699-709. https://doi.org/10.12989/sss.2018.22.6.699.
  2. Ahmadi, H.R., Daneshjoo, F. and Khaji, N. (2015), "New damage indices and algorithm based on square time-frequency distribution for damage detection in concrete piers of railroad bridges", Struct. Control Hlth., 22(1), 91-106. https://doi.org/10.1002/stc.1662.
  3. Ahmadi, H.R., Mahdavi, N. and Bayat, M. (2021), "A new index based on short time Fourier transform for damage detection in bridge piers", Comput. Concrete, 27(5), 447-455. https://doi.org/10.12989/cac.2021.27.5.447.
  4. Ahmadi, H.R., Mahdavi, N. and Bayat, M. (2021), "A novel damage identification method based on short time fourier transform and a new efficient index", Struct., 33, 3605-3614. https://doi.org/10.1016/j.istruc.2021.06.081.
  5. Bayat, M., Ahmadi, H.R. and Mahdavi, N. (2019), "Application of power spectral density function for damage diagnosis of bridge piers", Struct. Eng. Mech., 71(1), 57-63. https://doi.org/10.12989/sem.2019.71.1.057.
  6. Bonabeau, E., Dorigo, M. and Theraulaz, G. (2000), "Inspiration for optimization from social insect behaviour", Nature, 406(6791), 39-42. https://doi.org/10.1038/35017500.
  7. Chen, Z. and Yu, L. (2018), "A new structural damage detection strategy of hybrid PSO with Monte Carlo simulations and experimental verifications", Measure., 122, 658-669. https://doi.org/10.1016/j.measurement.2018.01.068.
  8. Chen, Z., Fang, H., Ke, X. and Zeng, Y. (2016), "A new method to identify bridge bearing damage based on radial basis function neural network", Earthq. Struct., 11(5), 841-859. https://doi.org/10.12989/eas.2016.11.5.841.
  9. Cornwell, P., Doebling, S.W. and Farrar, C.R. (1999), "Application of the strain energy damage detection method to plate-like structures", J. Sound. Vib., 224(2), 359-374. https://doi.org/10.1006/jsvi.1999.2163.
  10. Cui, M., Wu, G., Chen, Z., Dang, J., Zhou, M. and Feng, D. (2021), "Geometric attention regularization enhancing convolutional neural networks for bridge rubber bearing damage assessment", J. Perform. Constr. Facil., 35(5), 04021061. https://doi.org/10.1061/(asce)cf.1943-5509.0001634.
  11. Ding, Z., Li, J. and Hao, H. (2019), "Structural damage identification using improved Jaya algorithm based on sparse regularization and Bayesian inference", Mech. Syst. Signal. Pr., 132, 211-231. https://doi.org/10.1016/j.ymssp.2019.06.029.
  12. Dinh-Cong, D. and Nguyen-Thoi, T. (2021), "A new efficient two-stage method for damage localization and quantification in shell structures", Appl. Soft Comput., 108, 107468. https://doi.org/10.1016/j.asoc.2021.107468.
  13. Dinh-Cong, D., Nguyen-Thoi, T. and Nguyen, D.T. (2021), "A two-stage multi-damage detection approach for composite structures using MKECR-Tikhonov regularization iterative method and model updating procedure", Appl. Math. Model., 90, 114-130. https://doi.org/10.1016/j.apm.2020.09.002.
  14. Dinh-Cong, D., Nguyen-Thoi, T. and Vinyas, M. (2019b), "Two-stage structural damage assessment by combining modal kinetic energy change with symbiotic organisms search", Int. J. Struct. Stab. Dyn., 19(10), 1950120. https://doi.org/10.1142/S0219455419501207.
  15. Dinh-Cong, D., Vo-Duy, T. and Nguyen-Thoi, T. (2018), "Damage assessment in truss structures with limited sensors using a two-stage method and model reduction", Appl. Soft Comput., 66, 264-277. https://doi.org/10.1016/j.asoc.2018.02.028.
  16. Dinh-Cong, D., Vo-Duy, T., Ho-Huu, V. and Nguyen-Thoi, T. (2019a), "Damage assessment in plate-like structures using a two-stage method based on modal strain energy change and Jaya algorithm", Invers. Probl. Sci. Eng., 27(2), 166-189. https://doi.org/10.1080/17415977.2018.1454445.
  17. Fan, Q. (2021), "A two-step damage identification based on cross-model modal strain energy and simultaneous optimization", IOP Conf. Ser.: Earth Environ. Sci., 643(1), 012145. https://doi.org/10.1088/1755-1315/643/1/012145.
  18. Farrar, C.R., Baker, W.E., Bell, T.M., Cone, K.M., Darling, T.W., Duffey, T.A., ... & Migliori, A. (1994). "Dynamic characterization and damage detection in the I-40 bridge over the Rio Grande (No. LA-12767-MS)", Los Alamos National Lab., NM, USA. https://doi.org/10.2172/10158042.
  19. Gu, J., Gul, M. and Wu, X. (2017), "Damage detection under varying temperature using artificial neural networks", Struct. Control Hlth. Monit., 24(11), e1998. https://doi.org/10.1002/stc.1998.
  20. Holland, J.H. (1992), Adaptation in Natural and Artificial Systems: An Introductory Analysis with Applications to Biology, Control, and Artificial Intelligence, The MIT Press.
  21. Huang, M. and Lei, Y. (2020), "Bearing damage detection of a reinforced concrete plate based on sensitivity analysis and chaotic moth-flame-invasive weed optimization", Sensor., 20(19), 5488. https://doi.org/10.3390/s20195488.
  22. Huang, M., Cheng, S., Zhang, H., Gul, M. and Lu, H. (2019), "Structural damage identification under temperature variations based on PSO-CS hybrid algorithm", Int. J. Struct. Stab. Dyn., 19(11), 1950139. https://doi.org/10.1142/s0219455419501396.
  23. Huang, M., Cheng, X. and Lei, Y. (2021), "Structural damage identification based on substructure method and improved whale optimization algorithm", J. Civil Struct. Hlth., 11(2), 351-380. https://doi.org/10.1007/s13349-020-00456-7.
  24. Huang, M., Lei, Y. and Li, X. (2019), "Structural damage identification based on [l. sub. 1] regularization and bare bones particle swarm optimization with double jump strategy", Math. Probl. Eng., 2019, 1-16. https://doi.org/10.1155/2019/5954104.
  25. Huang, M., Lei, Y., Li, X. and Gu, J. (2021), "Damage identification of bridge structures considering temperature variations-based SVM and MFO", J. Aerosp. Eng., 34(2), 04020113. https://doi.org/10.1061/(asce)as.1943-5525.0001225.
  26. Huang, M., Li, X., Lei, Y. and Gu, J. (2020), "Structural damage identification based on modal frequency strain energy assurance criterion and flexibility using enhanced Moth-Flame optimization", Struct., 28, 1119-1136. https://doi.org/10.1016/j.istruc.2020.08.085.
  27. Huang, M.S., Gul, M. and Zhu, H.P. (2018), "Vibration-based structural damage identification under varying temperature effects", J. Aerosp. Eng., 31(3), 04018014. https://doi.org/10.1061/(asce)as.1943-5525.0000829.
  28. Li, B., Lei, Y., Zhou, D., Deng, Z., Yang, Y. and Huang, M. (2021), "Bearing damage detection of a bridge under the uncertain conditions based on the bayesian framework and matrix perturbation method", Shock. Vib., 2021, 1-17. https://doi.org/10.1155/2021/5576362.
  29. Li, J., Law, S.S. and Ding, Y. (2012), "Substructure damage identification based on response reconstruction in frequency domain and model updating", Eng. Struct., 41, 270-284. https://doi.org/10.1016/j.engstruct.2012.03.035.
  30. Lieu, Q.X., Nguyen, P.C., Lee, S., Lee, J. and Luong, V.H. (2020), "Structural damage detection using model order reduction and two-stage method", ICSCEA 2019, Eds. Reddy, J.N., Wang, C.M., Luong, V.H. and Le, A.T., Singapore.
  31. Majumdar, A. and Nanda, B. (2020), "A comparative study on inverse vibration based damage assessment techniques in beam structure using ant colony optimization and particle swarm optimization", Adv. Sci., Eng. Medic., 12(7), 918-923. https://doi.org/10.1166/asem.2020.2649.
  32. Mirjalili, S., Mirjalili, S.M. and Lewis, A. (2014), "Grey wolf optimizer", Adv. Eng. Softw., 69, 46-61. https://doi.org/10.1016/j.advengsoft.2013.12.007.
  33. Ni, Y., Liu, C., Gao, E. and Song, W. (2020), "Research on damage index of bridge pot rubber bearing based on correlation and sensitivity analysis and SVM", 2020 International Conference on Urban Engineering and Management Science (ICUEMS), April.
  34. Pan, C.D., Yu, L., Liu, H.L., Chen, Z.P. and Luo, W.F. (2018), "Moving force identification based on redundant concatenated dictionary and weighted l1-norm regularization", Mech. Syst. Signal. Pr., 98, 32-49. https://doi.org/10.1016/j.ymssp.2017.04.032.
  35. Park, G., Hong, K.N. and Yoon, H. (2021), "Vision-based structural FE model updating using genetic algorithm", Appl. Sci., 11(4), 1622. https://doi.org/10.3390/app11041622.
  36. Seyedpoor, S.M. (2012), "A two stage method for structural damage detection using a modal strain energy based index and particle swarm optimization", Int. J. Nonlin. Mech., 47(1), 1-8. https://doi.org/10.1016/j.ijnonlinmec.2011.07.011.
  37. Shadravan, S., Naji, H.R. and Bardsiri, V.K. (2019), "The sailfish optimizer: A novel nature-inspired metaheuristic algorithm for solving constrained engineering optimization problems", Eng. Appl. Artif. Intel., 80, 20-34. https://doi.org/10.1016/j.engappai.2019.01.001.
  38. Sun, H., Lus, H. and Betti, R. (2013), "Identification of structural models using a modified Artificial Bee Colony algorithm", Comput. Struct., 116, 59-74. https://doi.org/10.1016/j.compstruc.2012.10.017.
  39. Torkzadeh, P., Goodarzi, Y. and Salajegheh, E. (2013), "A two-stage damage detection method for large-scale structures by kinetic and modal strain energies using heuristic particle swarm optimization", Int. J. Optim. Civil Eng., 3(3), 465-482.
  40. Weng, S., Zhu, H., Gao, R., Li, J. and Chen, Z. (2018), "Identification of free-free flexibility for model updating and damage detection of structures", J. Aerosp. Eng., 31(3), 04018017. https://doi.org/10.1061/(asce)as.1943-5525.0000837.
  41. Weng, S., Zhu, H.P., Xia, Y. and Mao, L. (2013), "Damage detection using the eigenparameter decomposition of substructural flexibility matrix", Mech. Syst. Signal. Pr., 34(1-2), 19-38. https://doi.org/10.1016/j.ymssp.2012.08.001.
  42. Xiang, C.S., Li, L.Y., Dang, C. and Zhou, Y. (2021), "Damage identification of simply support beam based on strain energy information entropy", Bridge Maintenance, Safety, Management, Life-Cycle Sustainability and Innovations. Eds. Yokota, H. and Frangopol, D.M., CRC Press.
  43. Xuxi, Q., Weijun, Q. and Kai, D. (2021), "A diagnosis method for slab bridge bearing failure based on vibration mode parameters", ICAIIS 2021: 2021 2nd International Conference on Artificial Intelligence and Information Systems, May.
  44. Yu, L. and Li, C. (2014), "A global artificial fish swarm algorithm for structural damage detection", Adv. Struct. Eng., 17(3), 331-346. https://doi.org/10.1260/1369-4332.17.3.331.
  45. Zhuang, J.S. (2015), Bridge Support, China Railway Publishing Housing, Beijing, China. (in Chinese)