Smart Structures and Systems

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

Safety diagnosis process for deteriorated buildings using a 3D scan-based reverse engineering model

  • Jae-Min Lee (Department of Architecture, Yeungnam University) ;
  • Seungho Kim (Department of Architecture, Yeungnam University College) ;
  • Sangyong Kim (Department of Architecture, Yeungnam University)
  • Received : 2021.09.28
  • Accepted : 2022.09.12
  • Published : 2023.01.25
⟨ Previous Next ⟩

Abstract

As the number of deteriorated buildings increases, the importance of safety diagnosis, maintenance, and the repair of buildings also increases. Traditionally, building condition assessments are performed by one person or one company and various inspections are needed. This entails a subjective judgment by the inspector, resulting in different assessment results, poor objectivity and a lack of reliability. Therefore, this study proposed a method to bring about accurate grading results of building conditions. The limitations of visual inspection and condition assessment processes previously conducted were identified by reviewing existing studies. Building defect data was collected using the reverse-engineered three-dimensional (3D) model. The accuracy of the results was verified by comparing them with the actual evaluation results. The results show a 50% time-saving to the same area with an accuracy of approximately 90%. Consequently, defect data with high objectivity and reliability were acquired by measuring the length, area, and width. In addition, the proposed method can improve the efficiency of the building diagnosis process.

Keywords

Acknowledgement

This work was supported by the National Research Foundation of Korea (NRF) grant funded by the Korea government (MSIT) (No. 2020R1A2C1005263).

References

  1. Ani, A.I.C., Johar, S., Tawil, N.M., Abd Razak, M.Z. and Hamzah, N. (2015), "Building information modeling (BIM)-based building condition assessment: A survey of water ponding defect on a flat roof", Jurnal Teknologi, 75(9), 25-31. https://doi.org/10.11113/jt.v75.5222
  2. Anuar, M.Z.T., Sarbini, N.N., Ibrahim, I.S., Osman, M.H., Ismail, M. and Khun, M.C. (2019), "A comparative of building condition assessment method used in Asia countries: A review", IOP Conference Series: Mater. Sci. Eng., 513(1), 012029. https://doi.org/10.1088/1757-899X/513/1/012029
  3. Celik, O., Terrell, T., Gul, M. and Catbas, F.N. (2018), "Sensor clustering technique for practical structural monitoring and maintenance", Struct. Monitor. Maint., Int. J., 5(2), 273-295. https://doi.org/10.12989/smm.2018.5.2.273
  4. Craig, G. (2021), "Issue : Commercial Drones", SAGE business researcher, pp. 1-15.
  5. Choi, S.S. and Kim, E.K. (2015), "Design and implementation of ision-based structural safety inspection system using small unmanned aircraft", Proceeding of the 2015 17th International Conference on Advanced Communication Technology, New York, USA, July. https://doi.org/10.1109/ICACT.2015.7224924
  6. Choi, J., Yeum, C.M., Dyke, S.J. and Jahanshahi, M.R. (2018), "Computer-aided approach for rapid post-event visual evaluation of a building facade", Sensors, 18(9), 3017. https://doi.org/10.3390/s18093017
  7. Falorca, J.F. and Lanzinha, J.C.G. (2020), "Facade inspections with drones-theoretical analysis and exploratory tests", Int. J. Build. Pathol. Adaptat., 39(2), 235-258. https://doi.org/10.12989/smm.2021.8.3.257
  8. Faqih, F., Zayed, T. and Soliman, E. (2020), "BIM Based Facility Condition Assessment", Proceedings of International Conference on Civil Infrastructure and Construction, pp. 162-171. http://dx.doi.org/10.29117/cic.2020.0022
  9. Fils, P., Jang, S. and Sherpa, R. (2021), "Field implementation of low-cost RFID-based crack monitoring using machine learning", Struct. Monitor. Maint., Int. J., 8(3), 257-278. https://doi.org/10.12989/smm.2021.8.3.257
  10. Frohlich, C. and Mettenleiter, M. (2004), "Terrestrial laser scanning-new perspectives in 3D surveying", Int. Arch. Photogramm. Remote Sens. Spatial Inform. Sci., 36(Part 8), W2.
  11. Huang, H., Zhang, C. and Hammad, A. (2021), "Effective Scanning Range Estimation for Using TLS in Construction Projects", J. Constr. Eng. Manage., 147(9), 04021106. https://doi.org/10.1061/(ASCE)CO.1943-7862.0002127
  12. IM-19-E6-007 (2019), Detailed Guidelines for Implementation of Safety and Maintenance of Facilities (Safety Inspection and Diagnostics) Instructions, Korea Authority of Land & Infrastructure Safety; Jinju, Korea.
  13. Jang, K. and An, Y.K. (2018), "Multiple crack evaluation on concrete using a line laser thermography scanning system", Smart Struct. Syst., Int. J., 22(2), 201-207. https://doi.org/10.12989/sss.2018.22.2.201
  14. Jung, H.J., Lee, J.H., Yoon, S. and Kim, I.H. (2019), "Bridge Inspection and condition assessment using Unmanned Aerial Vehicles (UAVs): Major challenges and solutions from a practical perspective", Smart Struct. Syst., Int. J., 24(5), 669-681. https://doi.org/10.12989/sss.2019.24.5.669
  15. Kang, T.W., Kim, J.E. and Jung, T.S. (2016), "Deriving measures to improve MEP facility management work based on 3D reverse design", JKAIS, 17(8), 38-45.
  16. Kim, S.K. (2017), Application and Utilization of Drone Imaging, Korea Society Broadcasting Media Magazine, April.
  17. Kim, S.H. (2019), "3D Point Cloud and 4D BIM-based Construction Project EV Tracking Process", Ph.D. Dissertation, Yeungnam University, Gyeongsan, Korea.
  18. Kwan, A.K.H. and Ng, P.L. (2015), "Building Diagnostic Techniques and Building Diagnosis: The Way Forward", Engineering Asset Management-Systems, Professional Practices and Certification, New York, USA. https://doi.org/10.1007/978-3-319-09507-3_74
  19. Lattanzi, D. and Miller, G.R. (2014), "3D scene reconstruction for robotic bridge inspection", J. Infrastr. Syst., 21(2), 04014041. https://doi.org/10.1061/(ASCE)IS.1943-555X.0000229
  20. Law, D.W., Holden, L. and Silcock, D. (2015), "The assessment of crack development in concrete using a terrestrial laser scanner (TLS)", Austral. J. Civil Eng., 13(1), 22-31. https://doi.org/10.1080/14488353.2015.1092635
  21. Liu, D., Chen, J., Hu, D. and Zhang, Z. (2019), "Dynamic BIMaugmented UAV safety inspection for water diversion project", Comput. Indust., 108, 163-177. https://doi.org/10.1016/j.compind.2019.03.004
  22. Liu, D., Xia, X., Chen. J. and Li, S. (2021), "Integrating building information model and augmented reality for drone-based building inspection", J. Comput. Civil Eng., 35(2), 04020073. https://doi.org/10.1061/(asce)cp.1943-5487.0000958
  23. Mondal, T.G. and Jahanshahi, M.R. (2020), "Autonomous visionbased damage chronology for spatiotemporal condition assessment of civil infrastructure using unmanned aerial vehicle", Smart Struct. Syst., Int. J., 25(6), 733-749. https://doi.org/10.12989/sss.2020.25.6.733
  24. Mukupa, W., Roberts, G.W., Hancock, C.M. and Al-Manasir, K. (2016), "A review of the use of terrestrial laser scanning application for change detection and deformation monitoring of structures", Survey Rev., 49(353), 99-116. https://doi.org/10.1080/00396265.2015.1133039
  25. Ozcan, O. and Ozcan, O. (2021), "Automated UAV based multihazard assessment system for bridges crossing seasonal rivers", Smart Struct. Syst., Int. J., 27(1), 35-52. https://doi.org/10.12989/sss.2021.27.1.035
  26. Park, H.J., Ryu, J.R., Woo, S.H. and Choo, S.Y. (2016), "Improvement of the Building Safety Inspection Survey Method using Laser Scanner and BIM-based Reverse Engineering", J. Architect. Inst. Korea Plann. Des., 32(12), 79-90. https://doi.org/10.5659/JAIK_PD.2016.32.12.79
  27. Park, H.J., Lee, S.H., Kim, E.J. and Choo, S.Y. (2017), "A Proposal for Building Safety Diagnosis Processes Using BIM-Based Reverse Engineering Technology", Proceeding of the 22nd International conference of the Association for Computer-Aided Architectural Design Research in Asia, Hong Kong.
  28. Qi, Y., Yuan, C., Kong, Q., Xiong, B. and Li, P. (2021), "A deep learning-based vision enhancement method for UAV assisted visual inspection of concrete cracks", Smart Struct. Syst., Int. J., 27(6), 1031-1040. https://doi.org/10.12989/sss.2021.27.6.1031
  29. Sarker, M.M., Ali, T.A., Abdelfatah, A., Yehia, S. and Elaksher, A. (2017), "A cost-effective method for crack detection and measurement on concrete surface", Int. Arch. Photogramm. Remote Sens. Spatial Inform. Sci., 42, 237. https://doi.org/10.5194/isprs-archives-XLII-2-W8-237-2017
  30. Shi, Z. and Ergan, S. (2018), "Leveraging Point Cloud Data Detecting Building Facade Deteriorations Caused by Neighboring Consturction", Tamap J. Eng., 2018. https://doi.org/10.29371/2018.3.66
  31. Shi, Z. and Ergan, S. (2020), "Towards Point Cloud and ModelBased Urban Facade Inspection: Challenges in the Urban Facade Inspection Process", Proceeding of the Constuction Research Congress 2020: Safety, Workforce, and Education, Arizona, USA, March.
  32. Turkan, Y., Hong, J., Laflamme, S. and Puri, N. (2018), "Adaptive wavelet neural network for terrestrial laser scanner-based crack detection", Automat. Constr., 94, 191-202. https://doi.org/10.1016/j.autcon.2018.06.017
  33. Vasic, D., Ninkov, T., Bulatovic, V., Susic, Z. and Markovic, M. (2014), "Terrain mapping by applying unmanned aerial vehicle and lidar system for the purpose of designing in Serbia", Proceeding of the INGEO 2014-6th International Conference on Engineering Surveying, Prague, Czech Republic.
  34. Zhang, B., Wang, H., Huang, J. and Xu, N. (2019), "Model test on slope deformation and failure caused by transition from open-pit to underground mining", Geomech. Eng., Int. J., 19(2), 167-178. https://doi.org/10.12989/gae.2019.19.2.167