초록
목적: 본 연구는 서로 다른 필러를 가지는 복합레진에서 표면 연마 정도에 따라 수종의 레진 표면 강화제(Surface sealant)를 도포했을 때 복합레진의 거칠기에 미치는 영향에 대해 연구해 보고자 한다. 연구 재료 및 방법: 미세입자형 복합레진(Metafil CX, Sun Medical Co.)과 혼합형 복합레진(AeliteTM LS posterior, Bisco)을 사용하여 직경 8 mm, 높이 4 mm의 시편을 레진당 60개씩 제작하고, 3개 군으로 나누어 주수 하에 600, 1000, 2000 grit 사포(Tamiya finishing abrasives, Tamiya Inc.)로 연마하였다. 연마된 표면의 표면 조도(Ra)값은 Surface Roughness Tester (SJ-301, Mytutoyo)를 이용해 측정하였으며 연마된 각 시편에 레진 표면 강화제인 BisCoverTM LV (Bisco), Optiguard® (Kerr), and Seal-n-ShineTM (Pulpdent)를 각각 제조사의 지시에 따라 도포하였다. 레진 표면 강화제 처리 전과 후에 시편의 표면 조도를 측정하였으며 주사전자현미경(JSM-7500, JEOL)과 원자현미경(MultiMode IV, Veeco Instruments)으로 관찰하였다. 결과: 600 grit 사포로 연마한 후 레진 표면 강화제를 처리한 군은 도포 전보다 더 낮은 표면 조도(Ra)값을 보였으나(P < 0.05), 1000, 2000 grit으로 연마한 군에서는 도포 전 후 간에 통계적으로 유의한 차이를 보이지 않았다. 레진 표면 강화제 제품 간 뚜렷한 거칠기 차이는 나타나지 않았다. SEM과 AFM으로 시편을 관찰 시 마무리와 연마 후 레진 표면에 형성된 미세한 결함이 레진 표면 강화제를 처리한 후 현저히 줄어드는 양상을 보였다. 결론: 본 연구 결과, 마무리와 연마 후 복합레진 표면이 거친 경우에는 레진 표면 강화제의 도포가 미세한 결함을 채워서 거칠기에 영향을 줄 수 있지만 복합레진 표면의 연마 상태가 우수한 경우 레진 표면 강화제의 도포가 거칠기에 크게 영향을 주지 않음을 보여준다.
Purpose: This study aimed to evaluate the influence of surface sealants on the surface roughness of composite resins. Materials and Methods: The study used microfilled composite resin (Metafil CX, Sun Medical Co.) and hybrid composite resin (AeliteTM LS posterior, Bisco). Sixty specimens (8 mm in diameter and 4 mm in height) of each composite resin type were prepared and divided into 3 groups. Each specimen was ground with 600, 1000, and 2000-grit sandpaper. The Surface roughness (Ra) values were measured using a surface roughness tester (SJ-301, Mytutoyo) before and after surface sealant application. Surface sealants, BisCoverTM LV (Bisco), Optiguard® (Kerr), and Seal-n-ShineTM (Pulpdent), were applied to the specimens, as instructed and observed by scanning electron microscope (JSM-7500, JEOL) and atomic force microscope (MultiMode IV, Veeco Instruments). Results: Specimens ground with 600-grit sandpaper coated with surface sealants exhibited significantly lower Ra values than the untreated group (P < 0.05). Specimens ground with 1000 and 2000-grit sandpaper showed statistically no difference. There was no significant difference in surface roughness among BisCoverTM LV, Optiguard®, and Seal-n-ShineTM. SEM and AFM revealed remarkably decreased microdefects on the surfaces of composite resins after surface sealant application. Conclusion: Surface sealants can influence surface roughness when applied on the rough surface of composite resins but not on highly polished composite resins.